Motorola Mbp621-s User Guide

							Getting Started11
ENGLISH
2.2 Parent unit battery installation and power supply
A rechargeable battery pack is supplied and should be fitted, so that the parent 
unit can be carried to another location without losing the link and picture from 
the baby unit(s). Charge the parent unit before using it for the first time or when 
the parent unit indicates that battery is low. We recommend that the unit be 
charged for 15 hours prior to first use.       
1.Remove the belt clip/stand if it is attached to the parent unit.
2.Slide off the battery compartment cover.
3.Insert the plug of the rechargeable battery pack into the jack inside the 
battery compartment, and fit the battery pack into the compartment.
4.Slide the battery compartment cover back until it clicks into place, and re-
attach the belt clip/stand (refer to section 2.3).
5.Insert the DC plug of the power adapter with the bigger DC plug into the 
DC jack on the side of the parent unit.
6.Connect the other end of the power adapter to a suitable electrical outlet.
7.The battery level indicator comes on.
NOTE
Only use the provided power adapter and battery pack. 
We recommend that you install and fully charge the battery in the parent unit, 
so that it continues to work if you disconnect it from the electrical outlet to carry 
it to another location.
Battery JACK
Battery PLUG
DC PLUG
DC JACK 
						

							12Getting Started
2.3 Belt clip/stand on parent unit
1.The belt clip/stand attaches to the back of the parent unit and clips into the 
locking slots on each side.
NOTE
It will only fit one way, as indicated by UP and the arrows on the inner side of the 
clip.
2.The unit comes with the accessory fitted in the belt clip position.
3.You can convert it into the desktop position by simply pulling the back part of 
the clip out slightly and then rotating it by half a turn, as shown above.
Belt clip positionDesktop position 
						

							Using Your Digital Video Baby Monitor13
ENGLISH
3. Using Your Digital Video Baby Monitor
Please read these instructions carefully, and be aware that this digital video baby 
m o n i t o r  i s  o n l y  i n t e n d e d  a s  a n  a i d .  I t  i s not a substitute for responsible and proper 
adult supervision.
3.1 Power on or off the baby unit
•  Press and hold   to power on the baby unit. The Power/Link indicator turns 
on.
•  Press and hold   again to power off the baby unit. The Power/Link indicator 
turns off.
3.2 Power on or off the parent unit
•  Press and hold   to power on the parent unit. The Power/Link indicator and 
the LCD screen turn on.
•  Press and hold   again to power off the parent unit. The Power/Link 
indicator and the LCD screen turn off.
NOTE
If you place the parent and baby units too close together, you may hear a high 
pitched noise. This is not a fault. The units are designed to be operated at some 
distance apart, e.g. in separate rooms, so move the units further apart.
If the Power/Link indicator flashes on the baby unit or parent unit, they are not 
linked to each other. Make sure that both units are powered on, and reduce the 
distance between the units, but not closer than 3 feet.
3.3 Turn on or off the parent unit screen
You can turn off the parent unit screen without powering off the parent unit. 
When the screen is turned off, you can still hear sound from the baby unit.
•  Press   on the parent unit to turn off the screen at any time.
3.4 Adjust speaker volume of the parent unit
You can adjust the speaker volume from Volume 1 to Volume 5, or turn it off.
•  Press   or   on the parent unit when it is not in use.
When the speaker volume is set to off, the screen displays  . 
						

							14Using Your Digital Video Baby Monitor
3.5 Adjust LCD brightness of the parent unit
You can adjust the brightness of the parent unit screen from Level 1 to Level 5. 
The LCD brightness is preset to Level 3.
1.Press  when the parent unit is not in use.
2.Press 
- or + to scroll to  .
3.Press < or > to adjust brightness.
4.Press   to confirm your selection.
3.6 Adjust sound sensitivity of the baby unit
You can set the sound sensitivity level (Level 1 to Level 5) of the baby unit(s) from 
the parent unit. The higher the sound sensitivity level, the more sensitive the 
baby unit is in detecting sounds and transmitting them to the parent unit.
1.Press   when the parent unit is not in use.
2.Press 
- or + to scroll to  .
3.Press 
< or > to adjust the sensitivity level.
4.Press   to confirm your selection.
3.7 Turn sound activation on or off 
When the parent unit screen is turned off manually, you can set the screen to 
turn on automatically whenever sounds are detected from the baby unit(s). After 
20 seconds, when no sounds are detected from the baby unit(s), the parent unit 
screen will turn off automatically.
1.Press   when the parent unit is not in use.
2.Press 
- or + to scroll to  .
3.Press < or > to select   to turn on, or   to turn off sound activation.
4.Press   to confirm your selection.
You will hear a beep when the screen turns on or off due to sound activation.
3.8 Set temperature unit
You can set the temperature unit of the baby unit.
1.Press   when the parent unit is not in use.
2.Press 
- or + to scroll to  .
3.Press 
< or > to select oC or oF.
4.Press  to confirm your selection. 
						

							Using Your Digital Video Baby Monitor15
ENGLISH
3.9 Select camera
You can select the baby unit you want to view, or view all baby units in Scan 
Mode.
If you select Scan Mode, the screen switches to display another baby unit 
automatically after some time. The switching is made in a loop:   to  .
1.Press   when the parent unit is not in use.
2.Press 
- or + to scroll to  . 
3.Press 
< or > to select the baby unit you want to view (1, 2, 3 or 4) or Scan 
Mode ( ).
4.Press   to confirm your selection.
3.10 Zoom
You can zoom in or out when viewing an image from the baby unit.
1.Press 
> to zoom in.
2.Press and hold 
+, -, < or > to move the zoomed image upward, 
downward, leftward or rightward correspondingly.
3.Press 
< to zoom out.
3.11 Pairing and replacing baby unit(s)
The system comes with baby unit(s) already paired with the parent unit.
You can pair a maximum of four baby units to your parent unit. Each new baby 
unit must be paired to the parent unit before use.
To pair and replace a baby unit:
1.Press   when the parent unit is not in use.
2.Press 
- or + to scroll to  .
3.Press 
< or > to choose a desired baby unit slot, then press  . The screen 
displays .
NOTE
If you choose an occupied baby unit slot, the new baby unit will replace the 
existing baby unit.
4.Power on the new baby unit, and then immediately press and hold   until 
the Power/Link indicator flashes. 
						

							16Using Your Digital Video Baby Monitor
When pairing is successful, the screen displays  , followed by the image from 
the newly paired baby unit.
NOTE
If pairing fails, the screen displays  . Try the pairing process again. Only one 
baby unit can be paired at a time.
3.12 Talk to the baby unit
You can use the TALK function of the parent unit to talk to and comfort your 
baby. 
To talk to the baby unit: 
1.Press and hold 
T when viewing a baby unit. 
2.Speak towards the microphone on the parent unit. 
Your voice is broadcast to the baby unit. 
3.13 Reset settings to default
1.Press and hold   when the parent unit is not in use. At the same time, press 
 three times consecutively. 
2.Release  , and then press 
 again immediately. 
All settings will be reset to default. 
						

							Disposal of the Device (Environment)17
ENGLISH
4. Disposal of the Device (Environment) 
At the end of the product lifecycle, you should not dispose of 
this product with normal household waste. Take this product to 
a collection point for the recycling of electrical and electronic 
equipment. The symbol on the product, users guide and/or 
box indicates this.
Some of the product materials can be re-used if you take them 
to a recycling point. By reusing some parts or raw materials from used products 
you make an important contribution to the protection of the environment.
Please contact your local authorities in case you need more information on the 
collection points in your area.
Dispose of the battery pack in an environmentally-friendly manner according to 
your local regulations. 
						

							18Cleaning
5. Cleaning 
Clean your Digital Video Baby Monitor with a slightly damp cloth or with an anti-
static cloth. Never use cleaning agents or abrasive solvents.
Cleaning and care
•  Do not clean any part of the Digital Video Baby Monitor with thinners or other 
solvents and chemicals - this may cause permanent damage to the product 
which is not covered by the warranty.
•  Keep your Digital Video Baby Monitor away from hot, humid areas or strong 
sunlight, and do not let it get wet.
•  Every effort has been made to ensure high standards of reliability of your 
Digital Video Baby Monitor. However, if something does go wrong, please 
do not try to repair it yourself - contact Customer Service for assistance.
IMPORTANT
Always power off and disconnect the power adapter before cleaning your 
digital video baby monitor. 
						

							Troubleshooting19
ENGLISH
6. Troubleshooting
Power Indicator on the parent unit does not come on
•  Check whether the parent unit is powered on.
•  Check whether the supplied battery pack is correctly installed and that they 
are not drained.
•  Recharge the parent unit by connecting it to the electrical outlet.
Power/Link Indicator on the baby unit flashes
•  The baby unit may be not paired to the parent unit. Refer to section 3.11 to 
pair the baby unit.
•  The parent unit and the baby unit may be out of range with each other. 
Reduce the distance between the units, but not closer than 3 feet.
•  The baby unit may be powered off. Press and hold   to power on the baby 
unit.
Battery/Charging Indicator or   on the parent unit screen 
flashes
•  Battery pack in the parent unit is running low. Connect the parent unit to the 
electrical outlet with the supplied power adapter for recharging.
The parent unit beeps
•  The parent unit may have lost connection with the baby unit. Reduce the 
distance between the parent unit and the baby unit, but not closer than 
3 feet.
•  The baby unit may be powered off. Press and hold   to power on the baby 
unit.
•  Battery pack in the parent unit is running low. Connect the parent unit to the 
electrical outlet with the supplied power adapter for recharging. 
						

							20Troubleshooting
Cannot view the video image of the object from the parent 
unit
•  The LCD brightness may be set too low. Try to increase the brightness level. 
Refer to section 3.5 for details.
•  The parent unit and the baby unit may be out of range with each other. 
Reduce the distance between the units, but not closer than 3 feet.
•  Battery pack in the parent unit may be drained. Connect the parent unit to 
the electrical outlet with the supplied power adapter for recharging.
Cannot hear sound or baby cry from the parent unit
•  The volume level in the parent unit may be set too low, increase the volume 
level of the parent unit. Refer to section 3.4 for volume level settings.
•  The parent unit and the baby unit may be out of range with each other. 
Reduce the distance between the units, but not closer than 3 feet.
The digital video baby monitor system produces a high-
pitched noise
•  The parent unit and the baby unit are too close to each other. Make sure that 
the parent unit and baby unit are at least 3 feet away from each other.
•  The speaker volume of the parent unit may be set too high. Decrease the 
volume of the parent unit. Refer to section 3.4 for volume level settings.
Battery pack in the parent unit is running low quickly
•  The LCD brightness may be set too high. Try to decrease the brightness 
level. Refer to section 3.5 for details.
•  The volume level of the parent unit may be set too high, which consumes 
power. Decrease the volume level of the parent unit. Refer to section 3.4 for 
volume level settings.