Home > Motorola > Baby Care > Motorola Mbp38s2 Manual

Motorola Mbp38s2 Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Motorola Mbp38s2 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 249 Motorola manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Getting Started11
    ENGLISH
    1. Connect the micro USB plug of the power adapter to the Parent Unit and 
    the other end to a suitable electrical outlet. Only use the enclosed power 
    adapter (5V DC / 1500mA) with the micro USB plug.
    2. Press and hold the 
    0 POWER ON/OFF button for 1 second to turn ON the 
    Parent Unit.
    3. Once the Baby and Parent Units are switched on, the display on the Parent 
    Unit will show the video captured by the Baby Unit.
    4. If there is no connection or you are out of range, the unit will beep every 5 
    seconds. Move the Parent Unit closer to the Baby Unit until the link is re-
    established.
    5. Press and hold the 
    0 POWER ON/OFF button, until the progress bar 
    finishes scrolling, to turn OFF the Parent Unit.
    NOTE
    The battery icon   turns RED to indicate that the battery is low, and the 
    parent unit will beep every 15 seconds. The battery needs to be recharged; it 
    will take16 hours to charge fully.
    When charging
    1. Whilst the power is OFF, and the adapter is plugged in, an adapter logo will 
    appear on-screen and a flashing battery logo will display for 15 seconds. The 
    Blue LED at the top left corner will light up; indicating that the adapter is 
    plugged in.
    2. Whilst the power is ON, and the adapter is plugged in, the battery icon at 
    the top right corner of the screen will show that the battery is charging. The 
    Blue LED at the top left corner will light up to indicate that the adapter is 
    plugged in. 
    						
    							12Getting Started
    2.3 Registration (Pairing)
    The Baby Monitor is pre-registered to your Parent Unit. You do not need to 
    register it again unless the Baby Unit loses its link with the Parent Unit.
    To re-register your Baby Unit, or register a new Baby Unit, follow the procedures 
    below:
    1. Press the 
    M button of the Parent Unit and the menu bar will pop up.
    2. Press the < LEFT button or > RIGHT button until   is highlighted, and 
    the  del/   add/   view/   scan menu will pop up.
    3. Press the + UP button or - DOWN button to select   add, and press the O button to confirm.
    4. Camera  will pop up, press the + UP button or - DOWN 
    button to select the desired Camera and press the O button to start 
    searching for a camera unit. The green audio level LED will flash rapidly 
    while searching.
    5. Press the 
    O button to confirm.
    6. Press and hold the PAIR button underneath the Baby Unit until the Parent 
    Unit finds the camera, beeps and the video from the camera appears.
    NOTE
    If a particular Baby Unit was registered previously, registering this current 
    Baby Unit again will overwrite the old registration.
    /      /      / 
    						
    							Using the Baby Monitor13
    ENGLISH
    3. Using the Baby Monitor
    3.1 Setting up
    •  Place the Baby Unit in a convenient location (e.g. on a table) and point the 
    camera lens towards the area you want to monitor.
    •  Adjust the angle of the Baby Units head by rotating the camera up, down, left 
    and right until you are satisfied with the image shown on the Parent Unit.
    NOTE
    Do not place the Baby Unit within the babys reach! If there is interference with 
    the picture or sound, try moving the units to different locations, and ensure they 
    are not close to other electrical equipment.
    3.2 Pan and Tilt
    The camera can be remotely controlled from the Parent Unit.
    1. Press the 
    + UP button or - DOWN button to tilt up or down.
    2. Press the < LEFT button or > RIGHT button to pan left or right.
    3.3 Night Vision Mode
    The Baby Unit has 8 high-intensity infrared LEDs for picking up clear images in 
    the dark. When the built-in photo sensor on the top of the unit detects a low level 
    of ambient light, the LEDs will automatically activate and the screen on the 
    Parent Unit will display in black and white. The   icon will be displayed at the 
    top of the screen.
    3.4 Talk Mode
    Press and hold the T TA LK  but ton on  the  P are nt U nit to  t alk  to you r baby throu gh 
    the Baby Unit’s loudspeaker. The 
    T icon will be displayed at the top of the LCD 
    screen.
    3.5 Video ON/OFF
    Press V VIDEO ON/OFF key to turn the LCD display on or off, whilst still 
    leaving the audio monitor on. 
    						
    							14Using the Baby Monitor
    3.6 Temperature Display (HH °C / °F or LL °C / °F)
    The temperature reading from the temperature sensor at the back of the Baby 
    Unit will be displayed at the top of the LCD screen. The readings will turn RED if 
    the temperature goes above 29°C / 84°F or below 14°C / 57°F. The reading will 
    change to HH °C / °F if the temperature goes above 36°C / 97°F. The reading 
    will change to LL °C / °F if the temperature goes below 1°C / 34°F. 
    						
    							Parent Unit Menu Options15
    ENGLISH
    4. Parent Unit Menu Options
    4.1 Volume
    1. Press the Volume button - or + to adjust the volume level, the   icon will 
    pop up and you can select the desired volume level from level 0~8. (The 
    default volume level setting is level 5.) 
    4.2 Brightness
    1. Press the M button and the menu bar will pop up.
    2. Press the < LEFT button or > RIGHT button until   is highlighted.
    3. Press the + UP button or - DOWN button to select the desired brightness 
    level from level 1 ~ 8. (The default brightness level setting is level 4.)
    4.3 Lullaby
    1. Press the M button and the menu bar will pop up.
    2. Press the < LEFT button or > RIGHT button until   is highlighted.
    3. Press the + UP button or - DOWN button to select the desired song from 
    the 5 lullabies available. If an individual song is selected it will only play 
    once. (The default setting is lullaby OFF.)
    4. Press 
    O on the selected lullabies to select the desired song sound level.
    4.4 Zoom
    1. Press the M button and the menu bar will pop up.
    2. Press the < LEFT button or > RIGHT button until  is highlighted.
    3. Press the + UP button or - DOWN button to select the 1X or 2X Zoom. 
    (The default setting is 1X.) 
    4.5 Alarm
    1. Press the M button and the menu bar will pop up.
    2. Press the < LEFT button or > RIGHT button until   is highlighted.
    3. Press the + UP button or - DOWN button to select the alarm time (6h, 4h, 2h). (The default setting is Alarm OFF.)
    4. If an alarm time is selected, the Parent Unit will beep for about 45 seconds 
    after every 6, 4 or 2 hour period. 
    						
    							16Parent Unit Menu Options
    4.6 Camera Control
    4.6.1 Add (pair) a camera
    1. Press the M button and the menu bar will pop up.
    2. Press the < LEFT button or > RIGHT button until   is highlighted, and 
    the  del/   add/   view/   scan menu will pop up.
    3. Press the + UP button or - DOWN button to select  add, and press the O button to confirm.
    4. Camera   will pop up, press the + UP button or - DOWN 
    button to select the desired Camera, and press the O button to start 
    searching for a camera unit. The green audio level LED will flash rapidly 
    while searching.
    5. Press and hold the PA I R button on the underside of the Baby Unit until the 
    Parent Unit finds the camera, beeps and the picture from the camera appears.
    NOTE
    A camera can only be registered to one Parent Unit at any one time.
    4.6.2 View a camera
    1. Press the M button and the menu bar will pop up.
    2. Press the < LEFT button or > RIGHT button until   is highlighted and 
    the  del/   add/   view/   scan menu pops up.
    3. Press the + UP button or - DOWN button to select  view, and press the O button to confirm.
    4. Camera   will pop up, press the + UP button or - DOWN 
    button to select the desired camera, and press the  O button to view the 
    picture from that camera.
    TIP
    Quick Method to View Cameras instead of entering into the menu bar.
    Directly press OK repeatedly to select Camera , 
     scan.
    /      /      /
    /      /      /
    /      /      / 
    						
    							Parent Unit Menu Options17
    ENGLISH
    4.6.3 Delete a camera
    1. Press the M button and the menu bar will pop up.
    2. Press the < LEFT button or > RIGHT button until   is highlighted, and 
    the  del/   add/   view/   scan menu will pop up.
    3. Press the + UP button or - DOWN button to select  del, and press the O button to confirm.
    4. Camera   will pop up, press the + UP button or - DOWN 
    button to select the desired Camera, and press the O button to delete 
    that registration.
    Note:
    You are not allowed to delete the camera if there is only one registered camera 
    in the system.
    4.6.4 Scan camera
    1. Press the M button and the menu bar will pop up.
    2. Press the < LEFT button or > RIGHT button until   is highlighted, and 
    the  del/   add/   view/   scan menu will pop up.
    3. Press the + UP button or - DOWN button to select  scan, and press the O button to confirm.
    4. The screen will then display images from different registered cameras in a 
    loop of Camera 
     , changing about every 12 seconds.
    TIP
    Quick Method to View Cameras instead of entering into the menu bar.
    Directly press OK repeatedly to select Camera , 
     scan.
    4.7 Temperature
    1. Press the M button and the menu bar will pop up.
    2. Press the < LEFT button or > RIGHT button until   is highlighted.
    3. Press the + UP button or - DOWN button to select °C or °F.
    4.8 Power Saving mode
    1. Press the M button and the menu bar will pop up.
    2. Press the < LEFT button or > RIGHT button until V is highlighted.
    3. Press the + UP button or - DOWN button to select auto video off after 
    5 mins, 30 mins or 60 mins if not in charging.
    /      /      /
    /      /      /
    /      /      / 
    						
    							18Parent Unit Menu Options
    4.9 Video
    You can record a video of your baby with this function. The videos will be stored 
    on the SD Memory Card, so please ensure the memory card has enough free 
    memory.
    1. Press the 
    M button and the menu bar will pop up.
    2. Press the < LEFT button or > RIGHT button until   is highlighted.
    3. Press the + UP button or - DOWN button to select  , and press O 
    button to start video recording, press O button to stop.
    4. Press the + UP button or - DOWN button to select   and press O 
    button to play back the video. 
    Note:
    The video format is AVI which you can view on a computer/smartphone/tablet. 
    4.10 Time Setting
    1. Press the < LEFT button or > RIGHT button until   is highlighted and 
    press O Button.
    2. Press the < LEFT button or > RIGHT button to move between the settings.
    3. Press the + UP button or - DOWN button to set Date, Time format and 
    Ti m e .
    4.11 View multiple cameras on screen
    This function is only available when you have more than 1 Baby Unit (Camera).
    When the Picture in Picture function is On, you can view multiple cameras on 
    the screen.
    1. Press the 
    M button and the menu bar will pop up.
    2. Press the < LEFT button or > RIGHT button until   is highlighted.
    3. Press the O button to select Picture in Picture On/Off.
    4. When the Picture in Picture function is On, you can press the < LEFT 
    button/ > RIGHT button/ + UP button/ - DOWN button to switch 
    between cameras. 
    						
    							Disposal of The Device (environment)19
    ENGLISH
    5. Disposal of The Device (environment)
    At the end of the product lifecycle, you should not dispose of 
    this product with normal household waste. Take this product to 
    a collection point for the recycling of electrical and electronic 
    equipment. The symbol on the product, users guide and/or 
    box indicates this. 
    Some of the product materials can be reused if you take them to 
    a recycling point. By reusing some parts or raw materials from used products 
    you make an important contribution to the protection of the environment. 
    Please contact your local authorities in case you need more information on the 
    collection points in your area. 
    Dispose of the battery pack in an environmentally-friendly manner according to 
    your local regulations. 
    						
    							20Cleaning
    6. Cleaning 
    Clean the Baby Monitor with a slightly damp cloth or with an anti-static cloth. 
    Never use cleaning agents or abrasive solvents.
    Cleaning and care
    •  Do not clean any part of the product with thinners or other solvents and 
    chemicals – this may cause permanent damage to the product which is not 
    covered by the warranty.
    •  Keep the Baby Monitor away from hot, humid areas or strong sunlight, and 
    dont let it get wet.
    •  Every effort has been made to ensure high standards of reliability for your 
    Baby Monitor. However, if something does go wrong, please do not try to 
    repair it yourself – contact Customer Service for assistance. 
    						
    All Motorola manuals Comments (0)