Motorola Mbp25-2 User Guide

							Getting Started11
ENGLISH
2.Place the battery cover over the compartment and gently tighten the 
screw in a clockwise direction using a small cross-head or flat-head 
screwdriver.
2.3 Parent Unit Power Supply
IMPORTANT
Installing the rechargeable battery pack and charging it fully before use is 
recommended. This will allow the unit to operate on battery in the event of a 
power failure, or when moving to a different room.
1.Connect the small plug of the Power Adapter to the Parent Unit and the 
other end to the electrical outlet. Only use the enclosed Power Adapter (6V 
DC/500mA) with the slightly smaller DC plug.
2.Press and hold the 
P POWER ON/OFF button for 1 second to turn ON 
the Parent Unit.
3.Once the Baby and Parent Units are switched ON, the display on the Parent 
Unit will show the video captured by the Baby Unit.
Small cross-head or flat-head 
screwdriver. 
						

							12Getting Started
4.If there is no connection or you are out of range, the video display will go 
off, the symbol   will flash on the LCD display, and the unit will beep 
every 9 seconds. (If the unit is on scan   the   
1 ? symbol displays.) 
Move the Parent Unit closer to the Baby Unit to re-establish the link.
5.Press and hold the 
P POWER ON/OFF button, until the progress bar 
scrolls across fully, to turn OFF the Parent Unit.
NOTE
The battery icon   will turn Red, flash, and beep approximately every 5 
seconds to indicate that the battery is low and needs to be recharged. The 
battery pack will take approximately 16 hours to charge.
When charging
1.If the Parent Unit is turned OFF, when the Adapter is plugged in, it displays 
the Power Adapter icon briefly, then a large battery icon with internal 
segments cycling for 60 seconds, before the display goes blank. Note, the 
Unit will continue to charge. The Blue LED at the top left corner will light up 
to indicate that the Adapter is plugged in.
2.If the Parent Unit is turned ON, when the Adapter is plugged in, the battery 
icon in the screen’s top right corner will show that the battery is charging 
by cycling the internal segments. The segments stop cycling when the 
battery is fully charged. The Blue LED at the top left corner will light up to 
indicate that the Adapter is plugged in.
0 
						

							Getting Started13
ENGLISH
2.4 Registration (Pairing)
The Baby Monitor Camera is pre-registered to your Parent Unit. You do not 
need to register it again unless the Baby Unit loses its link with the Parent Unit.
To re-register your Baby Unit, or register a new Baby Unit, follow the procedure 
below:
1.Press the 
 button on the Parent Unit and then press the - DOWN button 
to select the ADD CAMERA icon  , and press the  button to confirm. 
2.
1 /  2 /  3 / 4 will pop up, press the + UP button or - DOWN button to 
select the desired Camera identification number and press the 
 button to 
start searching for a Camera Unit. The Green Audio Level LED turns on 
while searching.
3.Press and hold the PAIR button under the bottom left edge of the Camera 
Unit until the Parent Unit finds the Camera, beeps and the video from the 
Camera appears.
NOTE
If a particular Baby Unit was registered previously, registering this current Baby 
Unit again will overwrite the old registration.
If a Camera Unit is not found within about 30 seconds, the search will end and 
the Parent Unit will return to its previous mode. 
						

							14Using the Baby Monitor
3. Using the Baby Monitor
3.1 Setting Up
•  Place the Baby Unit in a convenient location (e.g. on a table) and point the 
camera lens towards the area you want to monitor.
•  Adjust the Baby Unit’s head angle by rotating the camera up, down, left and 
right until you are satisfied with the image on the Parent Unit.
NOTE
Do not place the Baby Unit within reach of a child or baby(s)! If there is 
interference with the picture or sound, try moving the units to different locations, 
and ensure they are not close to any other electrical equipment.
3.2 Night Vision Mode
The Baby Unit has 8 high-intensity infrared LEDs for picking up clear images in 
the dark. When the built-in photo sensor on the top of the unit detects a low level 
of ambient light, the LEDs will automatically activate and the screen on the 
Parent Unit will display in black and white. The 
N icon will be displayed at the top 
of the screen.
3.3 Video ON/OFF
Press the VIDEO ON/OFF button V on the Parent Unit to turn the LCD display 
on or off, but still leave the audio monitor on.
3.4 Talk Mode
Press and hold the T TALK button on the Parent Unit to talk to your baby through 
the Baby Unit’s loudspeaker. The 
T icon will be displayed at the top of the LCD 
screen. 
						

							Parent Unit Menu Options15
ENGLISH
4. Parent Unit Menu Options
4.1 Volume
1.While in monitor mode, press the + UP button or - DOWN button to 
select the desired volume level from level 1 ~ 8. (The default volume level 
setting is level 
4.)
4.2 Brightness
1.Press the  button and the first menu option will appear.
2.Select the BRIGHTNESS icon   and press the  button. 
3.Press the + UP button or - DOWN button to select the desired brightness 
level from level 1 ~ 8. (The default brightness level setting is level 4.)
4.Press the 
 button to return to the Monitor mode or the device will 
automatically return to the monitor mode after 30 seconds.
4.3 Zoom, Pan and Tilt
1.Press the Zoom button   to select 1X or 2X Zoom. (The default setting is 
1X.) When in 2X Zoom mode the   icon is displayed, and the functions of 
the + UP, - DOWN,   and   buttons are changed to allow you to view 
different areas of the original 1X video screen.
2.When in the 2X Zoom mode, press the + UP button or - DOWN button 
to move up or down the display view, or press the   or   buttons to pan 
the display left or right.
3.Press the ZOOM button   to return to normal mode.
4.4 Alarm
1.Press the  button and the first menu option will appear.
2.Press the - DOWN button to show the ALARM icon   and press the  button to confirm. 
3.Press the + UP button or - DOWN button to select the alarm time 
(6h, 4h, 2h). (The default setting is Alarm OFF (X).)
If an alarm time is selected, the Parent Unit will beep at the end of the 
selected 2, 4 or 6 hour period, and the alarm icon will flash red. The alarm is 
cancelled after 60 seconds or by pressing any button on the Parent Unit. 
Set the alarm again if you want another alarm call. 
						

							16Parent Unit Menu Options
4.5 Camera Control
4.5.1 Add (Pair) a camera
1.Press the  button and the first menu option will appear.
2.Press the 
- DOWN button to select the ADD CAMERA icon   and 
press the 
 button to confirm.
3.1 / 2 /  3 /  4 will pop up, press the + UP button or - DOWN button to 
select the desired Camera Unit, and press the 
 button to start searching 
for a Camera Unit. The Green Audio Level LED turns on while searching.
4.Press and hold the PAIR button underneath the Baby Unit until the Parent 
Unit finds the camera, beeps and the picture from the Camera appears.
NOTE
A Camera can only be registered to one Parent Unit at any one time.
4.5.2 View a Camera
1.Press the  button. 
2.Press the - DOWN button to select VIEW CAMERA icon   and press 
the 
 button to confirm.
3.
1 /  2 / 3 / 4 will pop up, press the + UP button or - DOWN button to 
select the desired Camera unit, and press the  button to view the picture 
from that Camera.
TIP
Quick Method to View Cameras instead of using the menu. 
Directly press   repeatedly to select 
1 / 2 /  3 /  4 or . 
						

							Parent Unit Menu Options17
ENGLISH
4.5.3 Delete a Camera
1.Press the  button.
2.Press the 
- DOWN button to select the DELETE CAMERA icon   and 
press the 
 button to confirm.
3.1 /  2 / 3 / 4 will pop up, press the + UP button or - DOWN button to 
select the desired Camera unit, press the 
 button then press the - 
DOWN button to select the DELETE CAM icon  .
4.Press the  button to confirm the deletion or   RETURN button to exit.
NOTE
You cannot delete the Camera if it is the only Camera paired in the system.
4.5.4 Scan the Cameras
1.Press the  button. 
2.Press the 
- DOWN button to select and choose the   symbol for Scan 
selection.
3.The screen will then display images from each registered Camera in a 
loop, changing once about every 10 seconds.
TIP
Quick Method to View Cameras instead of using the menu. 
Directly press   repeatedly to select 
1 / 2 /  3 /  4 or .
NOTE
If the Parent Unit is in scan mode and one of the registered Cameras is turned 
off or out of range, the scan will stop at the missing Camera (e.g. camera) and 
display the   
3 ? icon while emitting a warning beep every 8 seconds.
WARNING
Check the Camera and correct the fault immediately if you are using that 
Camera to monitor your baby.
If you want to continue in camera scan mode without that Camera, delete the 
Camera (see 4.5.3 Delete a Camera) and start the scan again. 
						

							18Disposal of the Device (environment)
5. Disposal of the Device (environment)
At the end of the product’s lifecycle, you should not dispose of 
this product with normal household waste. Take this product to 
a collection point for the recycling of electrical and electronic 
equipment. The symbol on the Product, User’s Guide and/or 
box indicates this. 
Some of the product materials can be reused if you take them to 
a recycling point. By reusing some parts or raw materials from used products 
you make an important contribution to the protection of the environment. 
Please contact your local authorities in case you need more information on the 
collection points in your area. 
Dispose of the battery pack in an environmentally-friendly manner according to 
your local regulations. 
						

							Cleaning19
ENGLISH
6. Cleaning 
Clean the Baby Monitor with a slightly damp or anti-static cloth. 
Never use cleaning agents or abrasive solvents.
Cleaning and care
•  Do not clean any part of the product with thinners or other solvents and 
chemicals –- this may cause permanent damage to the product which is not 
covered by the Warranty.
•  Keep your Baby Monitor away from hot, humid areas or conditions, strong 
sunlight and avoid moisture.
•  Every effort has been made to ensure high standards of reliability for your 
Baby Monitor. However, if something does go wrong, please do not try to 
repair it yourself – contact Customer Service for assistance. 
						

							20Help
7. Help
Display
No Display
•  Try recharging or replacing the Battery Pack.
•  Reset the Units. Disconnect the Battery Pack of the Parent Unit and unplug 
both the Units’ electrical power, then plug them back in.
•  Is the Unit turned on?
Press and hold the ON/OFF button 
P on the Parent Unit to turn it ON.
•  Is the correct Camera selected?
Change the Camera number, if necessary.
•  Is the video display turned on?
Press the VIDEO ON/OFF button 
V to turn it ON.
•  When operating using batteries only, the Display will go blank after 
4 minutes to save power. The unit is still active and will give you audio alerts. 
You can reactivate the screen by pressing any button. 
Registration
If the Baby Unit has lost its link with the Parent Unit
•  Try recharging or replacing the Battery Pack.
•  If the Baby Unit is too far away it may be out of range, move the Baby Unit 
closer to the Parent Unit.
•  Reset the Units by disconnecting them from the battery and electrical power. 
Wait about 15 seconds before reconnecting. Allow up to one minute for the 
Baby Unit and the Parent Unit to synchronize.
•  See Step 2.4 Registration (Pairing), if there is a need to re-register the units.