Motorola Cm Radio Basic Manual
Have a look at the manual Motorola Cm Radio Basic Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 249 Motorola manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Microphone Connector Pin Function6-5 3.0 Microphone Connector Pin Function Pin Function Description 19.3VRegulated 9.3V Supply (50mA max.) 2 Boot/DTMF Keypad ColumnThis pin function depends on the voltage applied to pin 3 (See pin 3, Hook description). When configured as “Boot”, applying 5V to this pin will set the radio to Boot state. When configured as “DTMF Keypad Column”, this pin will carry column voltages generated by the DTMF microphone (RMN5029). 3HookWhen 0V is applied to this pin (mic on hook), pins 2 and 7 will be configured to “Column” and “Row”. When no voltage is applied to this pin (mic off hook), this pin will read 2.7V, and pins 2 and 7 will be configured to “Column” and “Row”. When 9.3V is applied to this pin (programming cables or Mag One mic RMN5018), pins 2 and 7 will be configured to “Boot” and “SCI”. 4 Ground Used as ground 5Mic. AudioAudio input impedance: 500 ohms 80 mV rms input (standard mic) or 1.8 mV rms (low cost mic) at 1 kHz for 60% deviation. This path is enabled when Mic. PTT (pin 6) is keyed 6 Mic. PTT Microphone PTT is active low, so this port reads “0” when PTT is pressed and “1” when PTT is released. 10 K ohms internal pull up resistor to 9.3 V. Pulling low this pin will also pull low, via a diode, pin 3 (external MIC PTT) of the accessory connector. 7SCI/DTMF Keypad RowThe function of this pin depends on the voltage applied to pin 3 (see pin 3 description). When configured as “SCI”, serial communication with the radio is facilitated. When configured as “DTMF Keypad Row” this pin will carry new voltages generated by the DTMF mic (RMN5029) 8 Handset Rx AudioHandset audio output provides de-emphasized, muted Rx audio. The source impedance is 10 ohms and the output level (open circuit) is controlled by the volume control setting.
Chapter 7 MODEL CHART AND TEST SPECIFICATION 1.0 Model Chart (UHF1 403-440 MHz) CM Series UHF1 403-440MHz Model Description MDM50QNC9AA2_NCM140 403-440 MHz 1-25W 8-Ch MDM50QNC9AN2_N CM340 403-440 MHz 1-25W 10-Ch MDM50QNF9AA2_NCM160 403-440 MHz 1-25W 64-Ch MDM50QNF9AN2_N CM360 403-440 MHz 1-25W 100-Ch Item Description X PMUE2002_ S. Tanapa UHF1 25W 8 Ch BNC XPMUE2023_S. Tanapa UHF1 25W 10 Ch BNC X PMUE2005_ S. Tanapa UHF1 25W 64 Ch BNC XPMUE2025_S. Tanapa UHF1 25W 100 Ch BNC XXXX HKN4137_ Battery Power Cable XXFCN6288_Control Head X X FCN5523_ Control Head X X X X RMN50188_ HMN3596_Mag One Microphone Compact Microphone XXXX GLN7324_ Low Profile Trunnion XXXX6866546D02_RTTE Leaflet XXXX 6866537D37_ Safety Leaflet XPMUE2029ASServicing Kit CM140 X PMUE2045AS Servicing Kit CM340 XPMUE2031ASServicing Kit CM160 X PMUE2047AS Servicing Kit CM360 X = Indicates one of each is required
7-2 MODEL CHART AND TEST SPECIFICATION 2.0 Model Chart (UHF2 438-470 MHz) CM Series UHF2 438-470MHz Model Description MDM50RNC9AA2_NCM140 438-470 MHz 1-25W 8-Ch MDM50RNC9AN2_N CM340 438-470 MHz 1-25W 10-Ch MDM50RNF9AA2_NCM160 438-470 MHz 1-25W 64-Ch MDM50RNF9AN2_N CM360 438-470 MHz 1-25W 100-Ch Item Description X FUE1021_ S. Tanapa UHF2 25W 8 Ch BNC XPMUE2019_S. Tanapa UHF2 25W 10 Ch BNC X PMUE1999_ S. Tanapa UHF2 25W 64 Ch BNC XPMUE2021_S. Tanapa UHF2 25W 100 Ch BNC X X FCN6288_ Control Head XXFCN5523_Control Head XXXX HKN4137_ Battery Power Cable X X X X RMN50188_ HMN3596_Mag One Microphone Compact Microphone XXXX GLN7324_ Low Profile Trunnion XXXX6866546D02_RTTE Leaflet XXXX 6866537D37_ Safety Leaflet XFLE1621ASServicing Kit CM140 X PMUE2041AS Servicing Kit CM340 XPMUE2027ASServicing Kit CM160 X PMUE2043AS Servicing Kit CM360 X = Indicates one of each is required
Model Chart (VHF2 146-174 MHz)7-3 3.0 Model Chart (VHF2 146-174 MHz) CM Series VHF2 146-174MHz Model Description MDM50KNC9AA2_NCM140 146-174 MHz 1-25W 8-Ch MDM50KNC9AN2_N CM340 146-174 MHz 1-25W 10-Ch MDM50KNF9AA2_NCM160 146-174 MHz 1-25W 64-Ch MDM50KNF9AN2_N CM360 146-174 MHz 1-25W 100-Ch Item Description X FUD1183_ S. Tanapa VHF2 25W 8 Ch BNC XPMUD1879_S. Tanapa VHF2 25W 10 Ch BNC X PMUD1874_ S. Tanapa VHF2 25W 64 Ch BNC XPMUD1881_S. Tanapa VHF2 25W 100 Ch BNC X X FCN6288_ Control Head XXFCN5523_Control Head XXXX HKN4137_ Battery Power Cable X X X X RMN50188_ HMN3596_Mag One Microphone Compact Microphone XXXX GLN7324_ Low Profile Trunnion XXXX6866546D02_RTTE Leaflet XXXX 6866537D37_ Safety Leaflet XFLD1934ASServicing Kit CM140 X PMUD1889AS Servicing Kit CM340 XPMUD1883ASServicing Kit CM160 X PMUD1891AS Servicing Kit CM360 X = Indicates one of each is required
7-4 MODEL CHART AND TEST SPECIFICATION 4.0 Model Chart (Midband 66-88 MHz) CM Series Midband 66-88 MHz Model Description MDM50FNC9AN2_NCM340 66-88 MHz 1-25W 10-Ch MDM50FNF9AN2_N CM360 66-88 MHz 1-25W 100-Ch Item Description X FUC1601_ S. Tanapa Midband 25W 10 Ch BNC XFUC1603_S. Tanapa Midband 25W 100 Ch BNC X FCN6288_ Control Head XFCN5523_Control Head X X HKN4137_ Battery Power Cable XXHMN3596_Compact Microphone XXGLN7324_ Low Profile Trunnion XX6866546D02_RTTE Leaflet XX 6866537D37_ Safety Leaflet XPMUC1033ASServicing Kit CM340 X FUC1605ASServicing Kit CM360 X = Indicates one of each is required
Model Chart (VHF2 146-174 MHz - High Power) 7-5 5.0 Model Chart (VHF2 146-174 MHz - High Power) CM Series VHF2 146-174 MHz Model Description MDM50KQC9AA2_NCM140 146-174 MHz 25-45W 10-Ch MDM50KQF9AA2_N CM160 146-174 MHz 25-45W 100-Ch Item Description X PMUD1848_ S. Tanapa VHF2 45W 10 Ch BNC XPMUD1894_S. Tanapa VHF2 45W 100 Ch BNC X FCN6288_ Control Head XFCN5523_Control Head X X HKN4191_ Battery Power Cable XXRMN50188_Mag One Microphone X X GLN7324_ Low Profile Trunnion XX6866546D02_RTTE Leaflet XX 6866537D37_ Safety Leaflet XPMUD1885ASServicing Kit CM140 X PMUD1887ASServicing Kit CM160 X = Indicates one of each is required
7-6 MODEL CHART AND TEST SPECIFICATION 6.0 Model Chart (UHF2 438-470 MHz - High Power) CM Series UHF2 438-470 MHz Model Description MDM50RPC9AA2_NCM140 438-470 MHz 25-40W 10-Ch MDM50RPF9AA2_N CM160 438-470 MHz 25-40W 100-Ch Item Description X PMUE2008_ S. Tanapa UHF2 40W 10 Ch BNC XPMUE2011_S. Tanapa UHF2 40W 100 Ch BNC X FCN6288_ Control Head XFCN5523_Control Head X X HKN4191_ Battery Power Cable XXRMN50188_Mag One Microphone XXGLN7324_ Low Profile Trunnion XX6866546D02_RTTE Leaflet XX 6866537D37_ Safety Leaflet XPMUE2033ASServicing Kit CM140 X PMUE2035ASServicing Kit CM160 X = Indicates one of each is required
Specifications7-7 7.0 Specifications General Specification VHF2 UHF1 UHF2 Midband Frequency Range:146-174 MHz403-440 MHz438-470 MHz66-88 MHz Frequency Stability (-30°C to +60°C, 25°C Ref.)±2.5 PPM ±2 PPM ±2 PPM ±5.0 PPM Channel Capacity:CM140 - 8 CM340 - 10 CM160 - 64 CM360 - 100 Channel Spacing: 12.5/20/25 kHz Power Output:1-25W, 25-45W1-25W1-25W, 25-40W1-25W Power Supply: 13.2Vdc (10.8 - 15.6 Vdc) negative vehicle ground Dimensions (L X W X H)118mm X 169mm X 44mm Weight: 1.02 Kg Operating Temperature-30 to 60 o C Storage temperature -40 to 80 o C Shock and VibrationMeets MIL-STD 810-C,D&E and TIA/EIA 603 Dust Meets EN60529: IP54 HumidityMeets MIL-STD 810-C,D&E and TIA/EIA 603
7-8 MODEL CHART AND TEST SPECIFICATION Tr a n s m i t t e r Specification VHF2 UHF1 UHF2 Midband Frequency Stability: +/- 2.5ppm +/- 5ppm Modulation Limiting:±2.5 kHz @ 12.5 kHz ±4.0 kHz @ 20 kHz ±5.0 kHz @ 20/25 kHz Current Drain Transmit: 7A (25W) 8A (25W) FM Hum and Noise:-40 [email protected] kHz -45 dB@ 20/25 kHz-35 [email protected] kHz -40 dB@ 20/25 kHz-40 [email protected] kHz -45 dB@ 20/25 kHz Conducted/Radiated Emissions:-36 dBm < 1 GHz -30 dBm > 1 GHz Adjacent Channel Power-60dB @12.5, -70dB @ 20/25kHz Audio Response: ( 300 to 3000Hz)+1, -3dB Audio Distortion: @ 1000 Hz, 60% Rated Maximum Deviation: 3% Typical Receiver Specification VHF2 UHF1 UHF2 Midband Sensitivity (12dBSINAD): (ETS)0.35µV (12.5kHz) 0.30µV (25kHz) Typical Intermodulation : (ETS)>65 dB Adjacent Channel Selectivity: (ETS)75 dB @ 25 kHz 65 dB @ 12.5 kHz70 dB @ 25 kHz 60 dB @ 12.5 kHz Spurious Rejection: (ETS)75 dB 70 dB Rated Audio: (ETS) (Extended audio with 4 Ohm speaker)4W Internal , 13W External Audio Distortion @ Rated Audio:3% Typical Hum and Noise: -40 dB @ 12.5 kHz -45 dB @ 20/25 kHz-35 dB @ 12.5 kHz -40 dB @ 20/25 kHz-40 dB @ 12.5 kHz -45 dB @ 20/25 kHz Audio Response: ( 300 to 3000Hz)+1, -3dB Conducted Spurious Emission per FCC Part 15:-57 dBm 1 GHz