Motorola Cm Radio Basic Manual

Programming/Test Cable - RKN4083_2-19
11.0 Programming/Test Cable - RKN4083_
Figure 2-15Programming/Test Cable
Figure 2-16Pin Configuration of RKN4083
P1 (Male)
To Radio
 Test Set
J2 (Female)
To Mobile Radio
Accessory
Connector 1
1313
1
14 25
25 14J1 (Female)
To RIB
RLN4008
FL0830308O
1000    50mm
Cable+
_
1000    50mm
Cable+
_
17
181
219
20Viewed from
Front (pin end)
of Connector
FLO830308-0Note: Use with Adapter Cable FKN8113_
J2 Mobile 
Radio
Accessory 
Connector
SPEAKER -
EXTERNAL MIC
DIGITAL IN 1...

2-20MAINTENANCE
12.0 Adapter Cable - FKN8113_
Figure 2-17Pin Configuration of FKN8113
16-pin Female 
To Radio
Accessory 
Connector
SPEAKER -
EXTERNAL MIC
EXT. PTT
FLAT TX AUDIO SENSITIVITY
BUS+ (FOR CPS AND FLASHING)
GND
SWITCHED BATTERY VOLTAGE
SPEAKER +1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16SPEAKER -
EXTERNAL MIC
EXT.PTT
EXT ALARM
FLAT TX AUDIO
DIG IN
GND
DIG I/O
DIG IN
IGNITION
FLAT/FILTERED RX AUDIO
DIG IN
SWITCHED BATTERY VOLTAGE
DIG IN
RSSI
SPEAKER +
BUS +
BOOT CONTROL
N/C
N/C 1
2
3
4
5
6
7
8
9
10...

Chapter 3
TRANSCEIVER PERFORMANCE TESTING
1.0 General
These radios meet published specifications through their manufacturing process by utilizing high- 
accuracy laboratory-quality test equipment. The recommended field service equipment approaches 
the accuracy of the manufacturing equipment with few exceptions. This accuracy must be 
maintained in compliance with the manufacturer’s recommended calibration schedule.
2.0 Setup
Supply voltage is provided using a 13.2Vdc power supply. The equipment required...

3-2TRANSCEIVER PERFORMANCE TESTING
3.0 RF Test Mode (5-Tone Radios)
When the radio is operating in its normal environment, it is not possible to test all individual aspects 
of the transmitter and receiver performance. Therefore a special “test mode” is used to allow the 
service technician to perform certain functional tests on the product. A control head fuctional test 
mode is also available.
To enter test mode (CM360):
1.Turn the radio on.
2.Within less than one second of the power-up beep, press...

RF Test Mode (5-Tone Radios)3-3
8.In this mode all buttons, when pressed and held, will emit a high pitched beep and another 
when the button is released to verify button functionality.
9.Pressing P2 for at least one second will return the user to RF Test Mode 
Note:The radio powers up on the last used test state i.e. the last used test environment, test 
channel, and channel spacing.
Ta b l e 3 - 2Test Environments
No. of
BeepsCode ‘TT’
CM360Description Function
1
(high pitch)SQCarrier Squelch
(CSQ)RX:...

3-4TRANSCEIVER PERFORMANCE TESTING
Ta b l e 3 - 3Test Channel Spacing
Number of BeepsCode ‘CC’
CM360Channel Spacing
12525 kHz
2 12 12.5 kHz
32020 kHz
Ta b l e 3 - 4Test Frequencies
Te s t
ModeTest Channel Low
Powe r
CM360 CM340Test Channel High
Powe r
CM360 CM340VHF2 UHF R1 UHF R2 MIDBAND
TX011081.146.025403.025438.02566.125
RX011081.146.025 403.025 438.025 66.025
TX022092.150.700409.150443.35069.125
RX022092.150.700 409.150 443.350 69.025
TX033103.155.350415.350448.70073.125
RX033103.155.350 415.350...

RF Test Mode (MDC Radios)3-5
4.0 RF Test Mode (MDC Radios)
When the radio is operating in its normal environment, it is not possible to test all individual aspects 
of the transmitter and receiver performance. Therefore a special “test mode” is used to allow the 
service technician to perform certain functional tests on the product. A control head fuctional test 
mode is also available.
To enter test mode (display radios):
1.Turn the radio on.
2.Within ten seconds after the self test is complete, press...

3-6TRANSCEIVER PERFORMANCE TESTING
Ta b l e 3 - 6Test Channel Spacing
Number of Beeps Channel Spacing
125 kHz
2 12.5 kHz
320 kHz
Ta b l e 3 - 7Test Frequencies
Te s t  
ModeTest Channel Low
Power
CM160 CM140Test Channel High
Power
CM160 CM140VHF2
UHF R1 UHF R2
TX011088.146.025403.025438.025
RX 01 1 08 8.146.025 403.025 438.025
TX022099.150.700409.150443.300
RX 02 2 09 9.150.700 409.150 443.300
TX033100.155.300415.350448.700
RX 03 3 10 0.155.300 415.350 448.700
TX044111.160.000421.500454.000
RX 04 4 11...

RF Test Mode (MDC Radios)3-7
* See Tables 3-4 & 3.7Ta b l e 3 - 8Transmitter Performance Checks
Test Name Communications Analyzer Radio Test Set Comment
Reference 
FrequencyMode: PWR MON
4th channel test frequency*
Monitor: Frequency error
Input at RF In/OutTEST MODE,
Test Channel 4 
carrier squelch PTT to 
continuous 
(during the 
performance 
check)Frequency error: 
±150 Hz VHF,
±150 Hz UHF
±150 Hz MB
Power RF As above As above As above 1-25W 
Vo ice 
ModulationMode: PWR MON
4th channel test...

3-8TRANSCEIVER PERFORMANCE TESTING
Ta b l e 3 - 9Receiver Performance Checks
* See Tables 3-4 & 3.7Test NameCommunications
AnalyzerRadio Test Set Comment
Reference 
FrequencyMode: PWR MON
4th channel test frequency*
Monitor: Frequency error
Input at RF In/OutTEST MODE,
Test Channel 4 
carrier squelch 
output at 
antennaPTT to 
continuous 
(during the 
performance 
check)Frequency 
error to be 
±150 Hz VHF
±150 Hz UHF
±150 Hz MB
Rated Audio Mode: GEN
Output level: 1.0mV RF
4th channel test frequency*
Mod:...