Motorola Baby Monitor MBP36S MBP36S2 MBP36S3 MBP36S4 Users Guide

							button to select the desired Camera and press the , and press theO Getting Started11
ENGLISH2.During power ON, when adapter is plugged in, the battery icon on screens 
top right corner will show that the battery is charging. The Blue LED at the 
top left corner light up indicates adapter is plugged in.2.4 Registration (Pairing)The Baby monitor is pre-registered to your Parent Unit. You do not need to 
register it again unless the Baby Unit loses its link with the Parent Unit.
To re-register your Baby Unit, or register a new Baby Unit, follow the procedure 
below:
1.Press the M button of the parent unit and the menu bar will pop up.
2.Press the < LEFT button or > RIGHT button until   is highlighted, and 
the del/add/view/scan menu will pop up.
3.Press the + UP button or - DOWN button to select addbutton to confirm.
4.cam 1 / cam 2 / cam 3 / cam 4 will pop up, press the + UP button or - DOWN 
button to start 
searching for a camera unit. The green audio level LED will flash rapidly 
while searching.
5.Press the button to confirm.
6.Press and hold the PAIR button underneath the baby unit until the parent 
unit finds the camera, beeps and the video from the camera appears.
NOTE
If a particular Baby Unit was registered previously, registering this current 
Baby Unit again will overwrite the old registration.2.5 View Video Through TVConnect a suitable AV cable into the AV OUT socket on the side of the Parent 
Unit and into the AV input of the TV. Scroll to select   on the Parent unit. Scroll 
through the AV inputs on the TV menu until the Baby monitor picture is visible. 
AV cable is an optional accessory, which is to be purchased separately.
NOTE
The Monitors power button must be turned ON and CAM pre-selected before 
connecting the AV cable. Once the AV cable is connected, the Monitors 
controls cannot be activated.
You can hear also your baby in mono mode by connecting the 3.5mm plug 
wired headset to the AV OUT socket. O 
O  
						

							12Using the Baby Monitor3. Using the Baby Monitor3.1 Setting up•  Place the baby unit in a convenient location (e.g. on a table) and point the 
camera lens towards the area you want to monitor.
•  Adjust the baby units head angle by rotating the camera up, down, left and 
right until you are satisfied with the image in the parent unit.
NOTE
Do not place the baby unit within the babys reach! If there is interference with 
the picture or sound, try moving the units to different locations, and ensure they 
are not close to other electrical equipment.3.2 Pan and TiltThe camera can be remotely controlled from the parent unit.
1.Press the + UP button or - DOWN button to tilt upward or downward.
2.Press the < LEFT button or > RIGHT button to pan left or right.3.3 Night Vision ModeThe baby unit has 8 high-intensity infrared LEDs for picking up clear images in 
the dark. When the built-in photo sensor on the top of the unit detects a low level 
of ambient light, the LEDs will automatically activate and the screen on the 
parent unit will display in black and white. The   icon will be displayed at the 
top of the screen.3.4 Talk ModePress and hold the T T AL K  bu tt on  on  th e  pare n t u n it t o talk  t o yo ur b aby t hro ugh  
the baby unit’s loudspeaker. The T icon will be displayed at the top of the LCD 
screen.3.5 Video ON/OFFPress V VIDEO ON/OFF key to turn the LCD display on or off, but still leave the 
audio monitor on. 
						

							Using the Baby Monitor13
ENGLISH3.6 Temperature Display (HH °C / °F or LL °C / °F)The temperature reading from the temperature sensor at the back of the Baby 
Unit will be displayed at the top of the LCD screen. The readings will turn RED if 
the temperature goes above 29°C / 84°F or below 14°C / 57°F. The reading will 
change to HH °C / °F if the temperature goes above 36°C / 97°F. The reading 
will change to LL °C / °F if the temperature goes below 1°C / 34°F. 
						

							after every 6, 4 or 2 hour period. lullaby OFF)setting is 
individual song is selected it will only play once. (The default 
Press          on the selected lullabies to select the desired song sound level.14Parent Unit Menu Options4. Parent Unit Menu Options4.1 Volume1.Press the M button and the menu bar will pop up.
2.Press the < LEFT button or > button until   is highlighted.
3.Press the + UP button or - DOWN button to select the desired volume 
level from level 0 ~ 8. (The default volume level setting is level 4.)4.2 Brightness1.Press the M button and the menu bar will pop up.
2.Press the < LEFT button or > button until   is highlighted.
3.Press the + UP button or - DOWN button to select the desired brightness 
level from level 1 ~ 8. (The default brightness level setting is level 5.)4.3 Lullaby1.Press the M button and the menu bar will pop up.
2.Press the < LEFT button or > button until   is highlighted.
3.Press the + UP button or - DOWN button to select the desired song from 
the 5 lullabies available, or the cycle option to play all 5 songs in turn. If an 
4.4.4 Zoom1.Press the M button and the menu bar will pop up.
2.Press the < LEFT button or > button until  is highlighted.
3.Press the + UP button or - DOWN button to select the 1X or 2X Zoom. 
(The default setting is 1X.) 4.5 Alarm1.Press the M button and the menu bar will pop up.
2.Press the < LEFT button or > RIGHT button until   is highlighted.
3.Press the + UP button or - DOWN button to select the alarm time (6h, 4h, 2h). (The default setting is Alarm OFF.)
4.If an alarm time is selected, the parent unit will beep for about 45 seconds O  
						

							Directly press          repeatedly to select button to select desired Camera, and press the           button to view the  
picture from that camera., and press the button to select the desired Camera, and press the         button to start , and press the Parent Unit Menu Options15
ENGLISH4.6 Camera Control4.6.1 Add (pair) a camera1.Press the M button and the menu bar will pop up.
2.Press the < LEFT button or > RIGHT button until   is highlighted, and 
the del/add/view/scan menu will pop up.
3.Press the + UP button or - DOWN button to select addbutton to confirm.
4.cam 1 / cam 2 / cam 3 / cam 4 will pop up, press the + UP button or - DOWN 
searching for a camera unit. The green audio level LED will flash rapidly 
while searching.
5.Press and hold the PAIR button underneath the baby unit until the parent 
unit finds the camera, beeps and the picture from the camera appears.
NOTE
A camera can only be registered to one parent unit at any one time.4.6.2 View a camera1.Press the M button and the menu bar will pop up.
2.Press the < LEFT button or > RIGHT button until   is highlighted and 
the del/add/view/scan menu pops up.
3.Press the + UP button or - DOWN button to select viewbutton to confirm.
4.cam 1 / cam 2 / cam 3 / cam 4 will pop up, press the + UP button or - DOWN 
TIP
Quick Method to View Cameras instead of entering into the menu bar.cam 1, cam 2, cam 3, cam 4, scan.4.6.3 View multi-cameras on screen1.Press the M button and the menu bar will pop up.
2.Press the < LEFT button or > RIGHT button until   icon is highlighted.
3.Press the + UP button or - DOWN button to select 4-split screen On/Off.O 
O 
O 
O 
O  
						

							Directly press         repeatedly to select , and press the  button to select the desired Camera, and press the         button to delete  
that registration., and press the16Parent Unit Menu Options4.6.4 Delete a camera1.Press the M button and the menu bar will pop up.
2.Press the < LEFT button or > RIGHT button until   is highlighted, and 
the del/add/view/scan menu will pop up.
3.Press the + UP button or - DOWN button to select delbutton to confirm.
4.cam 1 / cam 2 / cam 3 / cam 4 will pop up, press the + UP button or - DOWN 
Note:
You are not allowed to delete the camera if there is only one registered camera 
in the system.4.6.5 Scan camera1.Press the M button and the menu bar will pop up.
2.Press the < LEFT button or > RIGHT button until   is highlighted, and 
the del/add/view/scan menu will pop up.
3.Press the + UP button or - DOWN button to select scanbutton to confirm.
4.The screen will then display images from different registered cameras in a 
loop of cam 1 / cam 2 / cam 3 / cam 4, changing about every 12 seconds.
TIP
Quick Method to View Cameras instead of entering into the menu bar.cam 1, cam 2, cam 3, cam 4, scan.4.7 Temperature1.Press the M button and the menu bar will pop up.
2.Press the < LEFT button or > RIGHT button until   is highlighted.
3.Press the + UP button or - DOWN button to select °C or °F.4.8 Power Saving mode1.Press the M button and the menu bar will pop up.
2.Press the < LEFT button or > RIGHT button until V is highlighted.
3.Press the + UP button or - DOWN button to select auto video off after 
5 mins, 30 mins or 60 mins if not in charging.O 
O 
O 
O  
						

							Disposal of The Device (environment)17
ENGLISH5. Disposal of The Device (environment)At the end of the product lifecycle, you should not dispose of 
this product with normal household waste. Take this product to 
a collection point for the recycling of electrical and electronic 
equipment. The symbol on the product, users guide and/or 
box indicates this. 
Some of the product materials can be reused if you take them to 
a recycling point. By reusing some parts or raw materials from used products 
you make an important contribution to the protection of the environment. 
Please contact your local authorities in case you need more information on the 
collection points in your area. 
Dispose of the battery pack in an environmentally-friendly manner according to 
your local regulations. 
						

							18Cleaning6. Cleaning Clean the MBP36S, MBP36S/2, MBP36S/3, MBP36S/4 with a slightly damp cloth 
or with an anti-static cloth. 
Never use cleaning agents or abrasive solvents.Cleaning and care•  Do not clean any part of the product with thinners or other solvents and 
chemicals –- this may cause permanent damage to the product which is not 
covered by the warranty.
•  Keep your MBP36S, MBP36S/2, MBP36S/3, MBP36S/4 away from hot, humid 
areas or strong sunlight, and dont let it get wet.
•  Every effort has been made to ensure high standards of reliability for your 
MBP36S, MBP36S/2, MBP36S/3, MBP36S/4. However, if something does go 
wrong, please do not try to repair it yourself –- contact Customer Service for 
assistance. 
						

							Help19
ENGLISH7. HelpDisplayNo display•  Try recharging or replacing the battery pack.
•  Reset the units. Disconnect the battery pack of the parent unit and unplug 
both the units electrical power, then plug them back in.
•  Is the unit turned on?
Press and hold the ON/OFF button P on the parent unit to turn it ON.
•  Is the correct camera selected?
Change the camera number, if necessary.
•  Is the video display turned on?
Press the VIDEO ON/OFF button V to turn it on.
•  When operating using batteries only, the Display will go blank after 
5 minutes or 30 minutes or 60 minutes to save power (depending on video 
on setting). The unit is still active and will give you audio alerts. You can 
reactivate the screen by pressing any button. RegistrationIf the Baby Unit has lost its link with the Parent Unit•  Try recharging or replacing the battery pack.
•  If the Baby Unit is too far away it may be going out of range, so move the 
Baby Unit closer to the Parent Unit.
•  Reset the units by disconnecting them from the battery and electrical power. 
Wait about 15 seconds before reconnecting. Allow up to one minute for the 
Baby Unit and the Parent Unit to synchronise.
•  See 2.4 Registration (Pairing), if there is a need to re-register the units.  
						

							product, so keep the baby monitor away at least 1.5m(5ft) from these types  •  Make sure there is at least 1 to 1.5 metre between the 
feedback.2 units to avoid audio20HelpInterferenceNoise interference on your parent unit•  Your baby and parent units may be too close. Move them farther apart.
•  lf the baby unit is too far away it may be out of range, so move the baby unit 
closer to the parent unit.
•  Make sure the baby and parent units are not near other electrical equipment, 
such as a television, computer or cordless/mobile telephone. 
•  Use of other 2.4 GHz products, such as wireless networks (Wi-Fi® routers), 
Bluetooth® systems, or microwave ovens, may cause interference with this 
of products, or turn them off if they appear to be causing interference.
•  If the signal is weak, try moving the Parent and/or Baby Unit to different 
positions in the rooms.