Mitsubishi Xl6600u Lcd Projector User Manual

							EN-11
Setting up your projector  (continued)
LENS SHIFT button
To adjust the positions of the projector and the screen, use LENS SHIFT button.
1.  Press the LENS SHIFT button.
•  The LENS SHIFT menu appears at the center of the screen.
2. Press the 
S, 
T, 
W or 
X button to move the image position.
• When the 
T button is pressed, the image moves down.
• When the 
S button is pressed, the image moves up.
• When the 
X button is pressed, the image moves to the right.
• When the 
W button is pressed, the image moves to the left.
•  When the ENTER button is pressed while the LENS SHIFT menu is displayed, the shift mode can be switched 
between FAST and STEP. When FAST is selected, the lens shifts in a large amount with the 
S, 
T, 
W or 
X button, 
and it shifts in a small amount when STEP is selected.
•  When the LENS SHIFT menu is displayed while no video signal is input to the projector, a crosshatch appears on 
the entire screen.
•  Be careful not to be caught in the opening in the lens while the lens is moving.
•  While the lens shift is working, the screen may fl icker.
Adjusting the projection angle
For the best projection, project images on a fl at screen installed at 90 degrees to the fl oor. If necessary, tilt the 
projector using the two adjustment feet on the bottom of the projector.
1.  Rotate the adjustment feet for fi ne adjustment.
After using the projector:
2.  Put the adjustment feet back into the projector by rotating the adjustment feet. 
When fi ne streaks are seen on projected images
This is due to interference with the screen surface and is not a malfunction. Replace the screen or displace the focus 
a little. (See page 15 or 20 for focus adjustment.) 
When projected images are distorted to a trapezoid
When the screen and the projector are not placed perpendicularly to each other,  projected images become 
trapezoidal. If you cannot make the projector and the screen perpendicular to each other by mechanical adjustments, 
adjust keystone.
To adjust keystone: 
Press the KEYSTONE button on the projector or the 
remote control to display KEYSTONE, and adjust the 
image by pressing the 
X, 
W, 
S or 
T button (or VOLUME 
+ or - button on the remote control). 
LENS SHIFT
FAST
SELECT : ENTER
Adjustment feet  Screen
In the following cases (for front projection):
Press the 
T 
(or -) button.Press the 
S 
(or +) button. Press the 
X 
button.Press the 
W 
button.
Important:
•  For proper keystone adjustment results, reset the lens to the factory-adjusted position using LENS SHIFT RESET 
in the INSTALLATION menu before carrying out keystone adjustment. (See page 24.)
•  When the keystone adjustment is carried out, the adjustment value is indicated. Note that this value doesn’t mean 
a projection angle. 
•  The allowable range of the adjustment value in the keystone adjustment varies depending on the installation 
conditions. 
•  When the keystone adjustment takes effect, the resolution decreases. In addition, stripes may appear or straight 
lines may bend in images with complicated patterns. They are not due to product malfunctions. 
•  When the keystone adjustment is performed, the displayed image may be distorted.
•  Depending on the installation conditions of the projector and the screen, a perfect rectangular image and the 
proper aspect ratio may not be obtained.
•  Noise may appear on the screen during the keystone adjustment because of the type of the video signal being 
projected and the setting values of the keystone adjustment. In such cases, set the keystone adjustment values in 
the range where the image is displayed without noise. 
•  When horizontal and vertical keystone adjustments are performed in combination, the adjustable range becomes 
narrower than in the case when they are performed separately.
•  In the keystone adjustment with the option lens, the proper aspect ratio may not be obtained. 
						

							EN-12
Setting up your projector  (continued)
Front projection, ceiling mounting
For ceiling mounting, you need the ceiling mount kit 
designed for this projector. Ask a specialist for installa-
tion. For details, consult your dealer.
•  The warranty on this projector does not cover any 
damage caused by use of any non-recommended 
ceiling mount kit or installation of the ceiling mount 
kit in an improper location. 
•  When using the projector mounted on the ceiling, 
set IMAGE REVERSE in the INSTALLATION menu to 
MIRROR INVERT. See page 24.
•  When the projector is mounted on the ceiling, im-
ages may appear darker than those projected in 
the case of tabletop mounting. This isn’t a product 
malfunction.
•  Ask your installation specialist to provide a breaker.
  When you do not use the projector, be sure to shut 
down the main power by the breaker.
•  Do not install the projector where the exhaust vents 
are exposed to air emitted by an air conditioning.
  Such installation may cause a breakdown.
•  Do not install the projector near a fi re alarm because 
it emits hot air from its exhaust vents.
•  For rear projection, set IMAGE REVERSE in the IN-
STALLATION menu to MIRROR. See page 24.
Caution:
•  Placing the projector directly on a carpet impairs 
ventilation by the fans, causing damage or failure. 
Put a hard board under the projector to facilitate 
ventilation. 
•  Place the projector at least 50 cm (or 20 inches) 
away from the wall to prevent the air inlet grille and 
the air outlet grilles that emit hot air from being 
blocked.
•  Do not use the projector in the following locations 
and manners, which may cause fi re or electric 
shock.
•  In a dusty or humid place.
•  In a sideways position, or with the lens facing 
down.
• Near a heater.
•  In an oily, smoky, or damp place such as a kitchen.
•  In direct sunlight.
•  Where the temperature rises high, such as in a 
closed car. 
•  Where the temperature is lower than +41ºF (or 
+5ºC) or higher than +104ºF (or +40ºC ).
Important:
•  We don’t recommend using the projector at an alti-
tude of 1500 meters or higher. Use at an altitude of 
1500 meters or higher may affect the projector’s life. 
Rear projection
Ask a specialist for installation. For details, consult 
your dealer. 
						

							EN-13
Viewing computer images
2 1
AUDIO OUTAUDIO IN 1/2
2 1
2 1
A. Connecting the projector to a computer
Preparation: 
•  Make sure that the power of the projector and that of the computer are turned off. 
•  When connecting the projector to a desktop computer, disconnect the RGB cable that is connected to the monitor. 
For analog connection: 
(For using the COMPUTER/COMPONENT VIDEO IN 2 
terminal.)
1.  Connect one end of the supplied RGB cable to the 
COMPUTER/COMPONENT VIDEO IN 2 terminal of the 
projector. 
2.  Connect the other end of the RGB cable to the monitor 
port of the computer.
•  When viewing images supplied from an analog-connected 
computer, press the COMPUTER 2 button on the remote 
control. 
For analog connection: 
(For using the COMPUTER/COMPONENT VIDEO IN 1 
terminal.)
1.  Connect one end of a commercially available BNC cable to 
the COMPUTER/COMPONENT VIDEO IN 1 terminal of the 
projector. 
2.  Connect the other end of the BNC cable to the 5 BNC 
terminals of the monitor port of the computer.
•  When viewing images supplied from an analog-connected 
computer, press the COMPUTER 1 button on the remote 
control. 
For digital connection: 
1.  Connect one end of a commercially available DVI cable 
to the COMPUTER/COMPONENT VIDEO DVI-D(HDCP) 
terminal of the projector. 
2.  Connect the other end of the DVI cable to the DVI terminal 
of the computer. 
•  When viewing images supplied from a digital-connected 
computer, press the DVI-D(HDCP) button on the remote 
control. 
•  Turn on the main power switch of the projector before 
starting the computer. 
For audio connection: 
1.  Connect one end of a commercially available PC audio 
cable to the AUDIO IN 1/2 terminal of the projector. 
2.  Connect the other end of the PC audio cable to the audio 
output terminal of the computer.
•  This projector uses stereo pin jack for its audio input. Check 
the type of the audio output terminal of the connected 
computer and prepare a proper cable for connection. Some 
computers don’t have the audio output terminal.
•  Speaker output is mono.
COMPUTER/
COMPONENT 
VIDEO IN 2
COMPUTER/
COMPONENT 
VIDEO DVI-D(HDCP)To monitor port
RGB cable
DVI cable (option)To DVI
Computer
PC audio cable (option)
To audio output 
terminal
2 1
R/PRG/Y B/PBH/HV V
V H/HV B/P
BG/Y R/PR
COMPUTER/
COMPONENT 
VIDEO IN 1
•  Additional devices, such as a conversion connector and an analog RGB output adapter, are required depending 
on the type of the computer to be connected.
•  Use of a long cable may decrease the quality of projected images. 
•  Images may not be projected correctly, depending on the type of the connected computer. 
•  When DVI-D signal is input, some signal setting menus are unavailable. 
•  Also read the instruction manual of the equipment to be connected. 
•  Contact your dealer for details of connection.
To monitor 
port (5 BNC)
Computer Computer Computer
BNC cable (option) 
						

							EN-14
Viewing computer images (continued)
2 1
1.  Plug the attached power cord into the power cord inlet of 
this projector.
2.  Plug the other end of the power cord into a power outlet.
•  The power cords for use in the U.S. and Europe are included with this projector. Use the appropriate one for your 
country. 
•  This projector uses the power plug of 3-pin grounding type. Do not take away the grounding pin from the power 
plug. If the power plug doesn’t fi t your wall outlet, ask an electrician to change the wall outlet. 
•  The provided power cord for the U.S. is rated at 120 V. Never connect this cord to any outlet or power supply 
using other voltages or frequencies than rated. If you use a power supply using other voltage than rated, prepare 
an appropriate power cord separately.
•  Use 100-240 V AC 50/60 Hz to prevent fi re or electric shock.
•  Do not place any objects on the power cord or do not place the projector near heat sources to prevent damage to 
the power cord. If the power cord should be damaged, contact your dealer for replacement because it may cause 
fi re or electric shock. 
•  Do not modify or alter the power cord. If the power cord is modifi ed or altered, it may cause fi re or electric shock. 
Caution:
•  Plug in the power cord fi rmly. When unplugging, hold and pull the power plug, not the power cord.
•  Do not plug in or out the power cord with your hand wet. It may cause electric shock.
Earthing 
terminal
Power cord (example)
About DDC
The COMPUTER/COMPONENT VIDEO IN 2 terminal of this projector complies with the DDC1/2B standard and the 
COMPUTER/COMPONENT VIDEO DVI-D(HDCP) terminal complies with the DDC2B standard. When a computer 
supporting this standard is connected to this terminal, the computer will automatically load the information from this 
projector and prepare for output of appropriate images. 
• 
When connecting a DDC-supporting computer to the projector, turn on the main power switch of the projector 
before starting the computer. 
1
Monitor
For monitor connection: 
1.  Connect the RGB cable from the monitor to the MONITOR 
OUT terminal of the projector.
For audio output connection: 
1.  Connect one end of a commercially available audio cable 
to the AUDIO OUT terminal of the projector. 
2.  Connect the other end (white and red) of the audio cable to 
the audio input terminals (L, R) of the audio equipment.  
•  When the audio cable is connected to the AUDIO OUT ter-
minal, the speaker output is muted.
AUDIO OUT2
1
Audio cable (option)To audio input 
terminals MONITOR OUT
RGB cable
B. Plugging the power cord 
						

							EN-15
Viewing computer images (continued)
C. Projecting images
Preparation:
•  Remove the lens cap.
1.  Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red. 
•  If the projector was turned off before the lamp was cooled down suffi ciently last time, the fan may start rotating 
and the POWER button may not work after the main power switch is turned ON. (The STATUS indicator blinks 
green.) After the fan stops rotating, press the POWER button to turn back on the POWER indicator. 
2.  Turn on the power of the connected computer. 
3.  Press the POWER button.
•  It may take about 1 minute for the lamp to light up. 
•  The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.
•  Do not cover the lens with the lens cap while the lamp is on. 
• 
After the POWER button is pressed, the image may fl icker before the lamp becomes stable. This is not a product 
malfunction. 
•  Regardless of the setting of LAMP MODE in the INSTALLATION menu, the STANDARD lamp mode is activated by 
default whenever the projector is turned on. When LAMP MODE has been set to LOW, the lamp mode changes 
from STANDARD to LOW about 1 minute after turn-on. 
•  The projector starts warming up when the POWER button is pressed. During the warm-up process, images may 
appear dark and no commands are accepted.
•  By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when 
the STATUS indicator blinks red. (See page 37.) 
•  After the POWER button is pressed, a white bar may appear on the right edge of the screen for about 1 second, 
but this is not a malfunction.
4.  Press the ZOOM/FOCUS button to display “FOCUS”.
5.  Adjust with the 
W or X button to get a fi ne picture. 
•  When the ENTER button is pressed while “FOCUS” is displayed, the adjustment mode is switched between 
FAST and STEP. When FAST is selected, the speed of focus controlled by the 
W or X button becomes fast, and it 
becomes slow when STEP is selected.
6.  Select an input source. 
•  Press the COMPUTER button on the projector or the COMPUTER 1, COMPUTER 2 or DVI-D(HDCP) button on 
the remote control that is corresponding to the terminal in use. 
•  The input source is switched from COMPUTER 1 to COMPUTER 2 to DVI at every press of the COMPUTER 
button on the projector. 
• The projector automatically selects the appropriate signal format. The selected signal format is displayed on the screen.
•  You cannot change the input source while the menu is being displayed.
•  Though it may take some time before an image is displayed on the screen depending on the type of the input 
signal, such symptom is not a malfunction. 
•  Images may not be projected in the correct position, depending on the type of the input signal. In such a case, 
press the AUTO POSITION button. (See page 16.)
• 
When you display a computer signal having the same resolution as that of a signal from a video device (1080p, 
etc.) using the COMPUTER1, 
COMPUTER 2 or DVI input source, select AUTO ADJUST adjustment mode as de-
scribed in “AUTO POSITION button” on page 16.
•  When COMPUTER 1 or COMPUTER 2 is chosen as the source, images supplied from the computer may fl icker. 
Press the W or X button on the remote control to reduce fl icker, if it occurs.
7.  Adjust the position of the projector to keep an appropriate projection distance with which images are projected in 
their specifi ed sizes. 
8.  Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page 10.) 
•  When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See page 11.)
9.  Press the ZOOM/FOCUS button to display “FOCUS” and then press the button again to display “ZOOM.”
10. Adjust with the 
W or X button to get an approximate size. 
•  When the ENTER button is pressed while “ZOOM” is displayed, the adjustment mode is switched between FAST 
and STEP. When FAST is selected, the speed of zoom controlled by the 
W or X button becomes fast, and it 
becomes slow when STEP is selected.
11. Press the LENS SHIFT button. The LENS SHIFT menu appears at the center of the screen.
12.Press the 
S or 
T button to adjust the vertical position and 
W or X button to adjust the horizontal position of the 
displayed image.
•  When the image is not displayed within the screen, adjust the projection angle. In addition, perform the keystone 
adjustment, if necessary. (See page 11.)
Repeat steps 4, 5 and 9 to 12, if necessary. 
POWER button
COMPUTER buttonCOMPUTER 1, 2 buttons
DVI-D(HDCP) buttonPOWER button
ZOOM/FOCUS button
LENS SHIFT button Main power switchZOOM/FOCUS buttonLENS SHIFT button 
						

							EN-16
Viewing computer images (continued)
Important:
•  Focus, zoom and lens shift adjustment is possible in the normal picture mode only.
•  When a 16:9 image is kept displayed for a long time before displaying 4:3 image, the afterimages of the black bars 
may appear on the 4:3 image screen. (See page 43.)
To stop projecting:
13. Press the POWER button. 
• A confi rmation message is displayed.
•  To cancel the procedure, leave the projector for a while or press any button except the POWER button. 
14. Press the POWER button again. 
•  The lamp goes out and the projector goes into a standby mode. In this standby mode, the STATUS indicator 
blinks green. 
15. Wait about 2 minutes for the STATUS indicator to be turned off. 
•  During this period of 2 minutes in the standby mode, the intake fan and exhaust fan rotate to cool the lamp. 
•  The air outlet fans rotate faster as the temperature around the projector rises.
•  Do not turn off the main power switch or unplug the power cord while the STATUS indicator is blinking. Turning 
off the main power switch or unplugging the power cord immediately after use may cause a breakdown. 
•  Though the fans make loud sounds during cooling, such symptom is not a malfunction.
16. Turn off the main power switch. 
•  The POWER indicator will go out. 
• If 
the main power switch should be turned off or the power cord should be unplugged accidentally while either 
the air inlet fan or the air outlet fans are operating or the lamp is on, allow the projector to cool down for 10 
minutes with the power off. To light the lamp again, press the POWER button. If the lamp doesn’t light up im-
mediately, repeat pressing the POWER button 2 or 3 times. If it should still fail to light up, replace the lamp. 
•  Cover the lens with the lens cap to protect it from dust.
•  For safety’s sake, unplug the power cord from the outlet.
•  When you repeat turning off the main switch within 30 minutes from the lamp illumination, an error may occur 
in the clock function of this product.
AV mute
The video and audio signals are temporarily muted when the AV MUTE button is pressed. To cancel muting, press the 
AV MUTE button again.
•  It takes several seconds before muting is completely canceled. 
•  If MUTE MODE in the INSTALLATION menu is set to IMAGE, the splash screen will appear when the AV MUTE 
button is pressed. 
•  You can alter the splash screen optionally. See page 32. 
•  The audio from the AUDIO OUT terminal is also muted by pressing the AV MUTE button.
AUTO POSITION button 
When the image supplied from the computer is displaced, carry out the following procedure. 
1.  Project a bright image containing as many texts and characters as possible. 
2.  When the screen saver has been enabled, disable it. 
3.  Press the AUTO POSITION button.  
  The projector automatically makes optimum positional settings for the input signal. 
•  When you press the AUTO POSITION button while a signal from a video device (or signal marked with *3 on 
page 46) is being input, a window to select either of the following two adjustment modes is displayed. 
- AUTO ADJUST:
  Suitable for signals supplied from a computer. 
- VIDEO SIGNAL:
  Suitable for signals supplied from a video device such as DVD.
  (When you select this mode, the adjustment using the RESOLUTION (MEMORIZE) menu (page 26) becomes 
unavailable.) 
  Select an appropriate mode using the
 W or X button and then press the ENTER button.
•  If the projected image is still displaced even after pressing the AUTO POSITION button several times, refer to 
the procedure to adjust computer images. (See pages 30 and 31.)
•  When you carry out this procedure with a dark image, the image may be displaced. 
When connecting to a notebook computer:
When the projector is connected to a notebook computer, images may not be projected in some cases. In such 
cases, set the computer so that it can output signals externally. The setting procedure varies depending on the type 
of the computer. See the instruction manual of your computer.
Example of the setting procedure for external output
Press the [Fn] key and any of the keys [F1] to [F12] at the same time. (The key to be pressed depends on the type of 
the computer you use.)  
						

							EN-17
Viewing video images
Connecting to a video player, etc.
1.  Connect one end (yellow) of the supplied audio/video cable 
to the VIDEO IN terminal of the projector. 
2.  Connect one end (white and red) of the supplied audio/
video cable to the audio input terminals (L/MONO, R) of the 
projector. 
3.  Connect the other end (yellow) of the audio/video cable to 
the video output terminal of the video equipment. 
4.  Connect the other end (white and red) of the audio/video 
cable to the audio output terminals (L, R) of the video 
equipment. 
When the video equipment is equipped with the S-video 
output terminal, make the connection as follows: 
1.  Connect one end of a commercially available S-video cable 
to the S-VIDEO IN terminal of the projector. 
2.  Connect the other end of the S-video cable to the S-video 
output terminal of the video equipment. 
3.  Connect one end (white and red) of the supplied audio/
video cable to the audio input terminals (L/MONO, R) of the 
projector. 
4.  Connect the other end (white and red) of the audio/video 
cable to the audio output terminals (L, R) of the video 
equipment. 
When using the BNC connector:
(For VIDEO input)
•  When the video output terminal of the connected video 
equipment is BNC type, use the VIDEO IN terminal (BNC 
type). 
•  Select VIDEO as the input source. 
•  When using the VIDEO IN terminal (BNC type) and the 
VIDEO IN terminal (RCA type) at the same time, the video 
signal input to the VIDEO IN terminal (RCA type) takes 
priority. 
When using the BNC connector:
(For S-VIDEO input)
•  When the video output terminals of the connected video 
equipment are BNC (Y/C) type, connect Y and C to the 
S-VIDEO IN (Y and C) terminals (BNC type) respectively.  
•  Select S-VIDEO as the input source. 
•  When using the S-VIDEO IN (Y and C) terminals (BNC type) 
and the S-VIDEO IN terminal (S type) at the same time, the 
video signal input to the S-VIDEO IN terminal (S type) takes 
priority. 
•  When connecting a monophonic video device, use the white (L) terminal to connect the audio cable. (The same 
audio signal is output from the channels L and R of the AUDIO OUT terminal.) 
•  Also read the instruction manual of the equipment to be connected. 
•  Contact your dealer for details of connection.
When a TV tuner or VCR is connected:
When you use this projector with a TV tuner or VCR connected, no image may appear or a message of “NO SIGNAL” 
may appear on the screen when you change the channel via any channel that is not being received. In such a case, 
set the channels of the TV tuner or VCR again. To avoid such symptom, use the TV tuner or VCR with its channel skip 
function (that is a function not to display channels that are not being received) enabled. 
A. Connecting the projector to video equipment
Preparation:
•  Make sure that the power of the projector and that of the video equipment are turned off.
34
12
13
4
2To VIDEO 
IN terminalTo video 
output 
terminal Video player, or the like
To S-VIDEO 
IN terminalS-video cable (option)
To S-video 
output 
terminalVideo player, or the likeAudio/video 
cable
To audio input 
terminalsTo audio 
output 
terminals
To audio 
input 
terminals
Audio/video 
cable
To audio 
output 
terminals
To VIDEO 
IN terminal 
(BNC)
BNC cable (option)To video 
output 
terminalVideo player, or the like
To S-VIDEO IN 
(Y and C) terminals 
(BNC)
BNC cable (option) To S-video (Y/C) 
output terminalsVideo player, or the like 
						

							EN-18
Connecting to video equipment having a HDMI terminal or DVI-D terminal
You can project high-quality images by connecting the COMPUTER/COMPONENT VIDEO DVI-D (HDCP) terminal of 
this projector to video equipment having a HDMI output terminal or DVI-D terminal. In addition, this projector supports 
HDCP and is able to receive encrypted digital video data that are output from DVD players.
• HDCP (High-bandwidth Digital Content Protection), developed by Intel Corporation, is a method to encrypt digital 
video data for the purpose of copy protection.
• HDMI (High-Defi nition Multimedia Interface) is fully backward compatible with computers, displays and consumer 
electronics devices incorporating the DVI standards.
• This projector can be linked with video devices equipped with HDMI output terminal or DVI-D output terminal. 
However, with some of them, this projector may not display any image or not operate correctly.
• If this projector doesn’t display any image or not operate correctly, see the operation manual of the video device 
for its connection.
• Use of a long cable may decrease the quality of projected images.
Connection (for video equipment having an HDMI terminal)
• Use a commercially available DVI-HDMI conversion cable.
•  Some cables may not be connected correctly depending on the size and shape of their connectors.
•  Use AUDIO IN 1 terminal for audio input.
Equipment having an 
HDMI terminal
To HDMI terminal
COMPUTER/COMPONENT 
VIDEO DVI-D (HDCP) To audio input 
terminals To audio output 
terminalsAudio cable (option)
DVI-HDMI conversion cable (option)
Viewing video images (continued)
CB(PB) Y CR(PR) 
B  G R 
AUDIO IN 1
BNC cable (option)
DVD player or HDTV decoderBNC-RCA connector (option)COMPUTER/COMPONENT 
VIDEO IN 1
Projector + DVD player or HDTV decoder
Some DVD players have an output connector for 3-line fi tting (Y, CB, CR). When connecting such DVD player with this 
projector, use the COMPUTER/COMPONENT VIDEO
 IN 1 terminals. 
•  The terminal’s names Y, PB, and PR are given as examples of when a HDTV decoder is connected.
•  The terminal’s names vary depending on the connected devices. 
•  Use BNC cables for connection.
•  Image may not be projected correctly with some DVD players.
• 
If colors aren’t displayed correctly when the projector is connected to a high-defi nition video device having R, G, 
and B output terminals, set COMPUTER INPUT to RGB in the SIGNAL menu.
Audio cable (option)
To audio output terminals 
						

							EN-19
Equipment having a 
DVI-D terminalTo audio output 
terminalsAudio cable (option)
To audio input 
terminals
To DVI-D terminal
DVI cable (option)COMPUTER/COMPONENT 
VIDEO DVI-D (HDCP)
Connection (for video equipment having a DVI-D terminal)
•  For connection to the DVI-D terminal, use a commercially available DVI cable. 
•  Some cables may not be connected correctly depending on the size and shape of their connectors.
•  When DVI is selected as the input source, settings of FINE SYNC., TRACKING, HOLD, etc. are unavailable. 
•  Use AUDIO IN 1 terminal for audio input.
When you connect this projector and a digital device (such as a DVD player) via the COMPUTER/COMPONENT 
VIDEO DVI-D (HDCP) terminal, black color may appear dark and deep, depending on the type of the connected 
device. 
•  This depends on the black level setting of the connected device. There are 2 kinds of methods to digitally transfer 
image data, in which different black level settings are employed respectively. Therefore, the specifi cations of the 
signals output from DVD players differ, depending on the type of the digital data transfer method they use. 
•  Some DVD players are provided with a function to switch the methods to output digital signals. When your DVD 
player is provided with such function, set it as follows.
  EXPAND or ENHANCED →
 NORMAL
•  See the users guide of your DVD player for details. 
•  When your digital device does not have such function, set INPUT LEVEL to ENHANCED in the ADVANCED 
MENU of the IMAGE menu of this projector, or adjust the black color by viewing the image.
B. Plugging in the power cord
Plug the power cord in the same way as in the case of “Viewing computer images.” (See page 14.)
Viewing video images (continued) 
						

							EN-20
Viewing video images (continued)
C. Projecting images
Preparation:
•  Remove the lens cap.
1.  Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red. 
•  If the projector was turned off before the lamp was cooled down suffi ciently last time, the fan may start rotating and 
the POWER button may not work after the main power switch is turned ON. (The STATUS indicator blinks green.) 
After the fan stops rotating, press the POWER button to turn back on the POWER indicator. 
2.  Turn on the power of the connected video equipment. 
3.  Press the POWER button.
•  It may take about 1 minute for the lamp to light up. 
•  The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.
•  Do not cover the lens with the lens cap while the lamp is on. 
• 
After the POWER button is pressed, the image may fl icker before the lamp becomes stable. This is not a product 
malfunction. 
•  Regardless of the setting of LAMP MODE in the INSTALLATION menu, the STANDARD lamp mode is activated by 
default whenever the projector is turned on. When LAMP MODE has been set to LOW, the lamp mode changes 
from STANDARD to LOW about 1 minute after turn-on. 
•  The projector starts warming up when the POWER button is pressed. During the warm-up process, images may 
appear dark and no commands are accepted.
•  By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when the 
STATUS indicator blinks red. (See page 37.) 
•  After the POWER button is pressed, a white bar may appear on the right edge of the screen for about 1 second, 
but this is not a malfunction.
4.  Press the ZOOM/FOCUS button to display “FOCUS”.
5. Adjust with the 
W or X button to get a fi ne picture. 
•  When the ENTER button is pressed while “FOCUS” is displayed, the adjustment mode is switched between 
FAST and STEP. When FAST is selected, the speed of focus controlled by the 
W or 
X button becomes fast, and it 
becomes slow when STEP is selected.
6.  Select an input source. 
•  Press the VIDEO button on the projector or the VIDEO or S-VIDEO button on the remote control that is 
corresponding to the terminal in use. 
•  The input source is switched between VIDEO and S-VIDEO at every press of the VIDEO button on the projector. 
•  You cannot change the input source while the menu is being displayed.•  Though it may take some time before an image is displayed on the screen depending on the type of the input 
signal, such symptom is not a malfunction. 
•  Some images become easier to view when the setting of aspect ratio is changed. (See page 21.)
•  When projecting images from a DVD player that is connected to the COMPUTER/COMPONENT VIDEO DVI-D (HDCP) 
terminal, press the COMPUTER button on the projector to select DVI or press the DVI-D (HDCP) button on the 
remote control. 
•  When projecting images from a DVD player that is connected to the COMPUTER/COMPONENT VIDEO IN 1 or 
COMPUTER/COMPONENT VIDEO IN 2 terminal, press the COMPUTER button on the projector or the COMPUTER 
1 or COMPUTER 2 button on the remote control. 
•  When COMPUTER 1 or COMPUTER 2 is chosen as the source, images supplied from the computer may fl icker. 
Press the W or X button on the remote control to reduce fl icker, if it occurs.
• 
When an image supplied from a video device to the COMPUTER1, COMPUTER2 or DVI input source is displaced, 
select VIDEO SIGNAL adjustment mode as described in “AUTO POSITION button” on page 16. 
7.  Adjust the position of the projector to keep an appropriate projection distance with which images are projected in their 
specifi ed sizes. 
8.  Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page 10.) 
•  When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See page 11.)
9.  Press the ZOOM/FOCUS button to display “FOCUS” and then press the button again to display “ZOOM.”
10. Adjust  with  the 
W or X button to get an approximate size. •  When the ENTER button is pressed while “ZOOM” is displayed, the adjustment mode is switched between FAST 
and STEP. When FAST is selected, the speed of zoom controlled by the W or X button becomes fast, and it 
becomes slow when STEP is selected.
11. Press the LENS SHIFT button. The LENS SHIFT menu appears at the center of the screen.
12. Press  the 
S or 
T button to adjust the vertical position and 
W or X button to adjust the horizontal position of the 
displayed image.
•  When the image is not displayed within the screen, adjust the projection angle. In addition, perform the keystone 
adjustment, if necessary. (See page 11.)
Repeat steps 4, 5 and 9 to 12, if necessary. 
Main power switchPOWER button
VIDEO button
COMPUTER button
ZOOM/FOCUS button
LENS SHIFT buttonCOMPUTER 1, 2 buttons
POWER button
DVI-D(HDCP) button
S-VIDEO button
VIDEO button
ZOOM/FOCUS buttonLENS SHIFT button