Mitsubishi Xl6500lu Lcd Projector User Manual

EN-21
Important:
•  Focus, zoom and lens shift adjustment is possible in the normal picture mode only.
To stop projecting:
13. Press the POWER button. 
• A confi rmation message is displayed.
•  To cancel the procedure, leave the projector for a while or press any button except the POWER button. 
14. Press the POWER button again. 
•  The lamp goes out and the projector goes into a standby mode. In this standby mode, the STATUS indicator 
blinks green. 
15. Wait about 2 minutes for the STATUS indicator to...

EN-22
Menu operation
•  Menus are not displayed when no signal is supplied to the projector. 
* 1: Not available when COLOR ENHANCER is set to sRGB.
* 2: Not available with certain signals.
* 3: Not available when the input signal is from the VIDEO IN or S-VIDEO IN terminal.
* 4: Available only when the input signal is TV60, TV50, 480i, 576i or 1080i.
* 5: Available only when the input signal is from the COMPUTER/COMPONENT VIDEO IN 2 terminal.
* 6: Setting range differs depending on the input signals.
*...

EN-23
Available settings in the menus
Set the following items on their relevant menus.  
1. IMAGE menu        IMAGE - ADVANCED menu
ITEM SETTING FUNCTION
COLOR ENHANCER  AUTO  Select to optimize the settings automatically depending on the input 
signal. (Select this option for normal use.)
  PRESENTATION  Select to make the displayed image look bright and crisp.
  STANDARD  Select to make the displayed image look natural.
  THEATER  This option, suitable for viewing movies, makes the displayed image look...

EN-24
2. INSTALLATION menu
Menu operation  (continued)
ITEM SETTING FUNCTION
LAMP MODE  STANDARD  Select this option when you want to view images in a well-lit room.
  LOW  Select to moderate the intensity of the lamp. The operating sound is 
reduced and the lamp lifetime becomes longer. 
•  When the lamp mode is switched, the projected image may fl icker. 
•  Frequent switching of the lamp mode may damage the lamp.
AUTO POWER ON  ON / OFF  When ON is chosen, the lamp is automatically lit when the power...

EN-25
3. FEATURE menu
FEATURE 
AUTO
AUTO 
opt. 
MENU POSITION 
VIDEO SIGNAL ? 
ASPECT 
RESET ALL 
English 
LANGUAGE A Ë 
OK 
SCART INPUT 
DISPLAY  
INPUT  PASSWORD 
FUNCTION 
CINEMA MODE AUTO 
1. 
SETUP 
AUTO 
OFF 
ITEM SETTING FUNCTION
ASPECT  AUTO  Select to change the aspect ratio automatically depending on the input 
signal. (Select this option for normal use.) 
 16:9 
  This option allows you to select the display position of squeezed (or 
horizontally compressed) images stored on DVD discs. By...

EN-26
4. SIGNAL menu SIGNAL - RESOLUTION (MEMORIZE) menu  SIGNAL - USER menu
ITEM SETTING FUNCTION
MEMORY CALL  AUTO / MEMORY 1  /  Use to select the setting of RESOLUTION (MEMORIZE) already saved. 
Impossible to select if no setting has been saved. AUTO is selected by default. 
It optimizes the signal format automatically depending on the type of video 
signal supplied from the computer. Press the ENTER button to clear the 
setting already saved. 
RESOLUTION (MEMORIZE 
 )    The current resolution is...

EN-27
5. INFORMATION menu
ITEM DESCRIPTION
LAMP TIME (LOW)   This item shows a lamp operating time (hour) calculated based on that LAMP MODE is LOW. 
•  When the LAMP MODE is STANDARD, this item shows a longer lamp operating time than 
the actual time. (See page 39 for the interval of lamp replacement.)
•  When the lamp operating time is 0 to 10 hours, “0H” is displayed. The lamp operating time 
exceeding 10 hours is indicated by the actual hours. 
•  When the lamp operating time reaches 3000 hours, the...

EN-28
Adjusting projected images
To adjust the brightness (CONTRAST and BRIGHTNESS):
You can make adjustments for the brightness of the projected image using the menu. 
(See page 23 for menu setting.) 
1.  Display the IMAGE menu. 
2.  Select CONTRAST or BRIGHTNESS by pressing the 
S or 
T button. 
3.  Adjust the selected item by pressing the 
W or 
X button. 
To cancel the menu:
4.  Press the MENU button. 
CONTRAST 
Select to adjust the contrast of the image. Every time the 
X button is pressed, the...

EN-29
To adjust the tone of white (COLOR TEMP.): 
You can select a preset color temperature (white tone) using the menu. 
(See page 23 for menu setting.) 
1.  Display the IMAGE menu. 
2.  Select COLOR TEMP. by pressing the 
S or 
T button. 
3.  Select your desired color temperature by pressing the 
W or 
X button. 
To cancel the menu:
4.  Press the MENU button. 
To adjust the tone of white (To customize the color temperature): 
To customize (and store) the color temperature to your preference, carry out...

EN-30
Adjusting projected images  (continued)
How to adjust the computer image
This projector automatically selects a proper signal format according to the type of video signal supplied from the 
computer. However, video signals from the computer may not be projected correctly depending on the types of the 
computer and images to be projected. In such a case, make adjustment according to the fl owchart below.
Adjustment is completed. When the size and position of 
the computer image are not correct....