Mitsubishi XL5950U Projector User Manual

							EN – 1
ENGLISH
FRANÇAIS
DEUTSCH
ITALIANO
ESPAÑOL
X L5950
XL5950L
LCD PROJECT OR
MODEL
XL5950U
XL5950LU
User Manual 
						

							EN – 2
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended
to alert the user to the presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of electric
shock.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the litera-
ture accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION
CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO
PREVENT BLADE EXPOSURE.
NOTE:
SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE IN-
STALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.
WARNING
Use the attached specified power supply cord. If you
use another power-supply cord, it may cause interfer-
ence with radio and television reception.
Use the attached RGB cable, RS-232C cable with this
equipment so as to keep interference within the limit
of a FCC Class A device.
This apparatus must be grounded.
DO NOT LOOK DIRECTLY INTO THE LENS
WHEN PROJECTOR IS IN THE POWER ON
MODE.
CAUTION
Not for use in a computer room as defined in the
Standard for the Protection of Electronic Computer/
Data Processing Equipment, ANSI/NFPA 75.When using the projector in Europe
COMPLIANCE NOTICE
This LCD Video Projector complies with the require-
ments of the EC Directive 89/336/EEC “EMC Direc-
tive” as amended by Directive 93/68/EEC and 73/23/
EEC “Low Voltage Directive” as amended by Direc-
tive 93/68/EEC.
The electro-magnetic susceptibility has been chosen
at a level that gains proper operation in residential
areas, on business and light industrial premises and
on small-scale enterprises, inside as well as outside
of  the buildings. All places of operation are
characterised by their connection to the public low
voltage power supply system.
WARNING
Use the attached RGB cable or RS-232C cable with
this equipment so as to keep interference within the
limits of a EN55022 Class B. Use the shielded D-
SUB/5 BNC cable with this equipment so as to keep
interference within the limits of a EN55022 Class B.
Please follow WARNINGS instructions. 
						

							EN – 3
ENGLISH
Contents
Important safeguards ........................................................................... 4
Overview ............................................................................................... 6
Using the remote control ...................................................................... 8
Battery installation ......................................................................................................... 8
Installation ............................................................................................ 9
Basic connections ............................................................................... 10
Projector + AV device .................................................................................................... 10
Projector + DVD player or HDTV decoder ................................................................... 10
Projector + computer ..................................................................................................... 11
Preparing the projector for operation ............................................... 12
To operate projector power ON .......................................................... 13
Menu operation .................................................................................. 15
Picture adjustment ............................................................................. 18
Advanced feature for presentation .................................................... 20
Expand ........................................................................................................................... 20
PinP (Picture in Picture) ............................................................................................... 20
Still ................................................................................................................................. 20
Mouse remote control .................................................................................................... 21
Lamp replacement ............................................................................. 22
Maintenance ....................................................................................... 23
About the terminal cover (with Anti-Theft Alarm device) ............... 24
Troubleshooting .................................................................................. 25
Indicators ............................................................................................ 26
Specifications ...................................................................................... 27
Kensington Lock ............................................................................................................ 27
Connectors .....................................................................................................................28
Dimensional drawings .................................................................................................. 28
What’s included in the box ............................................................................................ 28
Replacement part .......................................................................................................... 28
Specification of RGB signals in each computer mode of the projector ....................... 29
Specification of the attached lens (for XL5950LU) ...................................................... 30
Trademark, Registered trademark
Macintosh is registered trademark of Apple Computer Inc.
Other brand or product names are trademarks or registered trademarks of their respective holders. 
						

							EN – 4
Important safeguards
Please read all these instructions regarding your LCD
projector and retain them for future reference. Follow
all warnings and instructions marked on the LCD pro-
jector.
1. Read instructions
All the safety and operating instructions should
be read before the appliance is operated.
2. Retain instructions
The safety and operating instructions should be
retained for future reference.
3. Warnings
All warnings on the appliance and in the oper-
ating instructions should be adhered to.
4. Instructions
All operating instructions must be followed.
5. Cleaning
Unplug this projector from the wall outlet be-
fore cleaning it. Do not use liquid aerosol clean-
ers. Use a damp soft cloth for cleaning.
6. Attachments and equipment
Never add any attachments and/or equipment
without the approval of the manufacturer as
such additions may result in the risk of fire, elec-
tric shock or other personal injury.
7. Water and moisture
Do not use this projector near water or in con-
tact with water.
8. Accessories
Do not place this projector on an unstable cart,
stand, tripod, bracket or table. Use only with a
cart, stand, tripod bracket, or table recom-
mended by the manufacturer or sold with the
projector. Any mounting of the appliance should
follow the manufacturers instructions and
should use a mounting accessory recommended
by the manufacturer.10. Power sources
This projector should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power,
please consult your appliance dealer or local
power company.
11. Power-cord protection
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them. Pay particular at-
tention to cords at plugs, convenience receptacles,
and points where they exit from the appliance. Do
not put the power cord under a carpet.
12. Overloading
Do not overload wall outlets and extension cords
as this can result in a fire or electric shock.
13. Objects and liquids
Never push objects of any kind through open-
ings of this projector as they may touch danger-
ous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liq-
uid of any kind on the projector.
14. Servicing
Do not attempt to service this projector your-
self. Refer all servicing to qualified service per-
sonnel.
15. Damage requiring service
Unplug this projector from the wall outlet and
refer servicing to qualified service personnel un-
der the following conditions:
(a) If the power-supply cord or plug is dam-
aged.
(b) If liquid has been spilled, or objects have
fallen into the projector.
(c) If the projector does not operate normally
after you follow the operating instructions.
Adjust only those controls that are covered
by the operating instructions. An improper
adjustment of other controls may result
in damage and may often require exten-
sive work by a qualified technician to re-
store the projector to its normal operation.
(d) If the projector has been exposed to rain
or water.
(e) If the projector has been dropped or the
cabinet has been damaged.
(f) If the projector exhibits a distinct change
in performance - this indicates a need for
service.
16. Replacement parts
When replacement parts are required, be sure
that the service technician has used replacement
parts specified by the manufacturer or parts
having the same characteristics as the original
part. Unauthorized substitutions may result in
fire, electric shock or other hazards.
17. Safety check
Upon completion of any service or repair to this
projector, ask the service technician to perform
safety checks determining that the projector is
in a safe operating condition.
An appliance and cart combination should be
moved with care. Quick stops, excessive force and
uneven surfaces may cause the appliance and
cart combination to overturn.
9. Ventilation
Slots and openings in the cabinet are provided
for ventilation, ensuring reliable operation of the
projector and to protect it from overheating. Do
not block these openings or allow them to be
blocked by placing the projector on a bed, sofa,
rug, or bookcase. Ensure that there is adequate
ventilation and that the manufacturers instruc-
tions have been adhered to. 
						

							EN – 5
ENGLISH
WARNING:
Unplug immediately if there is something
wrong with your projector.
Do not operate if smoke, strange noise or odor comes
out of your projector. It might cause fire or electric
shock. In this case, unplug immediately and contact
your dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An
inadvertent contact may result in an electric shock.
Except as specifically explained in the Owners
Guide, do not attempt to service this product
yourself. Please contact your dealer when you want
to fix, adjust or inspect the projector.
Do not modify this equipment.
It can lead to fire or electric shock.
If you break or drop the cabinet.
Do not keep using this equipment if you break or
drop it. Unplug the projector and contact your dealer
for inspection. It may lead to fire if you keep using
the equipment.
Do not face the projector lens to the sun.
It can lead to fire.
Use correct voltage.
If you use incorrect voltage, it can lead to fire.
Do not place the projector on uneven
surface.
Place the projection on a leveled and stable surface
only. Please do not place equipment on unstable
surfaces.
Do not look into the lens when it is
operating.
It may hurt your eyes.Never let children look into
the lens when it is on.
Do not turn off the main power abruptly or
unplug the projector during operation.
It can lead to lamp breakage, fire, electric shock or
other trouble. It is best to wait for the fan to turn off
before turning main power off.
Do not touch Air outlet grille and Bottom
plate which becomes hot.
Do not touch them or put other equipment in front of
Air  outlet grille. The heated Air outlet grille and Bot-
tom plate may cause injury or damage to other equip-
ment. Also, do not set the projector on the desk which
is easily affected by heat.
Clean the air-filter once a month.
Clean the air-filter frequently. If the filter or ventila-
tion slots become clogged with dirt or dust, the tem-
perature inside of the projector may rise and cause
some troubles, such as damage of inside parts, and
shortening the life of panel.
Do not look into the air outlet grille when
projector is operating.
Heat, dust etc. may blow out of it and hurt your eyes.
Place of installation
For safety’s sake, refrain from setting the projector at
any place subjected to high temperature and high
humidity. Please maintain an operating temperature,
humidity, and altitude as specified below.
• Operating temperature: between +41°F (+5°C) and
+104°F (+40°C)
• Operating humidity:  between 30 and 90%
• Never put any heat-producing device under the pro-
jector so that the projector does not overheat.
• Do not attach the projector to a place that is un-
stable or subject to vibration.
• Do not install the projector near any equipment that
produces a strong magnetic field. Also refrain from
installing near the projector any cable carrying a
large current.
• Place the projector on a solid, vibration free sur-
face: otherwise it may fall, causing serious injury
to a child or adult, and serious damage to the prod-
uct.
• Do not stand the projector: it may fall, causing se-
rious injury and damage to the projector.
• Slanting the projector more than ±15˚(right and
left or front and rear) may cause trouble or
explosion of the lamp.
• Do not place the projector near air-conditioning unit
or heater to avoid hot air to the exhaust and venti-
lation hole of the projector.
COMPLIANCE NOTICE OF FCC
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-
ence when the equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as
set out in the interference-causing equipment standard entitled “Digital Apparatus”, ICES-003 of the Depart-
ment of Communications.
Changes or modifications not expressly approved by Mitsubishi could void the users authority to operate this
equipment.
COMPLIANCE NOTICE OF INDUSTRY CANADA
This Class A digital apparatus complies with Canadian ICES-003. 
						

							EN – 6
Overview
14
6 5 313 1
7 2
10 411 12
89
LAMP
VOLUME
ZOOM/
FOCUSKEYSTONE
TEMP
SOURCEMUTE AUTO  POSITION LENS SHIFT
MENUENTER
POWER
24567
8
9
10
11121317 1411815 16
3
REMOTE
INREMOTE
OUTINPUT 1
INPUT 2R/PRB/PBG/Y H/HVV
AUDIO
IN
AUDIO
OUTY
CRS-232C RS-232C/MOUSEUSB
S-VIDEO
VIDEO
2
VIDEO
1
L
AUDIO
R MAIN
AC IN
Control area
Terminal panel
1 Remote control sensor (Front)
2 Lens
3 Control area
4 Air outlet grille
5 Terminal panel
6 Air inlet grille
7 Easy-carry handle
8 Speaker
9 Kensington Security Lock Standard
connector
10 Remote control sensor (Rear)
1 LAMP indicator
2 TEMP (temperature) indicator
3 AUTO POSITION button
4 Direction buttons
5 MENU button
6 KEYSTONE button
7 VOLUME (+, –) buttons
8 SOURCE button
9 MUTE button (Audio/Video)
10 ZOOM/FOCUS button
1
 1 ENTER button
12 LENS SHIFT button
13 POWER button
14 POWER indicator
• The + and - buttons are used in the KEYSTONE and
ZOOM/FOCUS adjustment in addition to the volume
control.
1 REMOTE IN jack
2 Reset button
3 REMOTE OUT jack
4 COMPUTER / COMPONENT VIDEO INPUT 1
terminal (R/P
R, G/Y, B/PB, H/HV, V )(BNC)
5 RS-232C terminal(Mini DIN 8P)
6 RS-232C/MOUSE terminal(Mini DIN 8P)
7 USB terminal
8 VIDEO 2 terminal (S-Video)
9 VIDEO 1 terminal (RCA)
10 AUDIO terminals
1
 1 VIDEO 1 terminal (BNC)
12 VIDEO 2 terminals (Y,C)(BNC)
13 COMPUTER AUDIO OUT jack
14 COMPUTER AUDIO IN jack
15 COMPUTER OUTPUT terminal (D-SUB mini
15P)
16 COMPUTER / COMPONENT VIDEO INPUT 2
terminal (D-SUB mini 15P)
17 Power jack
18 Main power
O : OFF I : ON
213
8
9
10
5647 
						

							EN – 7
ENGLISH
Bottom side
1
2
31 Adjustment foot (Left/Right)
2 Air inlet grille/Filter cover
3 Lamp cover
Caution:
Do not replace the lamp immediately after using the
projector because the lamp has got extremely hot.
COMPUTER
VIDEO KEYSTONE
VOLUME
LASER
EXPAND
MENU R-CLICK ENTER
P in PSTILL
MUTE
LENS SHIFT16 : 9
12
12
ZOOM/FOCUS AUTOPOSITION
1
2
4
5
6
7
8
9
10
11
12
13
3
23
22
21
24 20
19
18
17
16
15
14
Remote control1 Laser aperture
2 Transmission window
3 Wired remote control jack
4 Indicator
5 POWER button
6 KEYSTONE button
7 ZOOM/FOCUS button
8 + , – (VOLUME) buttons
9 Mouse pointer
10 MENU button
1
 1 STILL button
12 PinP button
13 LENS SHIFT button
14 MUTE button (Audio/Video)
15 16 : 9 button
16 ENTER button
17 R-CLICK button (For mouse)
18Direction buttons
19 LASER button
20 AUTO POSITION button
21 EXPAND button
22 VIDEO 1, 2 button
23 COMPUTER 1, 2 button
24 Left click button (For mouse)
• The + and - buttons are used in the KEYSTONE and
ZOOM/FOCUS adjustment and the EXPAND mode in
addition to the volume control.
• Pressing the LASER button emits a laser beam. Even when
you keep holding down the LASER button, it is emitted
only one minute. To keep emitting it longer, press the
LASER button again.
• You can disable the LASER button to prevent laser
radiation due to misuse of the button.
How to disable the LASER button
While holding the LASER button down, press the }
button three times.
How to enable the LASER button
While holding the LASER button down, press the {
button three times.
About the laser beam
This remote control is a Class 2 laser product. (Max. output : 1 mW, Wavelength
: 640-660 nm)
Beam Divergence : 6m distance about 10.0mm x 10.0mm (±6.0mm)
CAUTION :
• Pressing the LASER button on the remote control emits a laser beam. Do not
look into the laser beam directly. Do not point the laser beam at anyone.
Looking at the laser beam directly may damage eyesight.
• Use of controls or adjustments or procedures other than those specified herein may
result in hazardous radiation exposure.
MADE  IN  CHINA
MANUFACTURER :   B 
MANUFACTURED RAYONNMENT LASER
NE PAS REGARDER DANS LE FAISCEAU
APPAREIL A LASER DE CLASSE2
LASER-STRAHLING 
NICHT IN DEN STRAHL BLICKEN
LASER KLASSE 2
RADIZION LASER
NON GUARDARE NEL RAGGIO LUCE
APPARECCHIO LASER DI CLASSE 2
WAVE LENGTH :640-660nm MAX OUTPUT:1mW
IEC 60825-1:1993+A1:1997+A2:2001
INTERLINK K.K.
SHINODA BLDG 1-10-7 HIGASHIKANDA CHIYODA-KU,TOKYO 101-0031,JAPANLASER RADIATION
DO NOT STARE INTO BEAM
WAVE  LENGTH:  640-660nmMAX  OUTPUT:  1mWCLASS  2  LASER  PRODUCT
AVOID  EXPOSURE-LASER
RADIATION  IS  EMITTED
  FROM  
THIS  
APERTURE
CAUTION
Comp l ies  with  21  CFR, 1040. 10  and  1040. 11
JANUARY  2003S
RADIAÇÃO LASER
EVITAR A EXPOSIÇÃO AO FEIXE
APARELHO LASER DA CLASSE 2
POTÊNCIA MÁXIMA: 1mW
COMPRIMENTO DE ONDA: 640 - 660 nm 
						

							EN – 8
Battery installation
Use two AA size batteries.
1. Remove the back cover of the remote control by pushing the battery compartment door in the direction of the
arrow.
2. Load the batteries making sure that they are positioned correctly (+ to +, and - to -).
• Load the batteries from - spring side, and make sure to set them tightly.
3. Replace the back cover.
Important:
• Do not use a new battery with an old one.
• Load batteries in the correct position.
• Do not heat, take apart, or throw batteries into fire.
• Do not try to recharge batteries. Do not use rechargeable batteries.
• If the solution of batteries comes in contact with your skin or clothes, rinse with water. If  the solution comes
in contact with your eyes, rinse them with water and then consult your doctor.
Operation area (for wireless control system)
The range for operation is about 10 m (about 32 feet) when the remote control points to the projector. The dis-
tance to the screen back to the projector must be less than 7 m (about 23 feet). Depending on the type of the
screen, the distance will be different.
Important:
Avoid the direct sunlight or fluorescent light to the remote control sensor. Also keep the distance of more than 2 m
(6.5) between the remote control sensor and fluorescent lamp on the remote control may not work correctly.
Using the wired remote control
Attached remote control for this projector can be used as a wired remote control with remote control cable. Wired
remote control is useful for operating in a distance or outside of the operating area.
20˚
15˚20˚
15˚
30˚ 30˚
12 3
•When REMOTE OUT terminal on this projector is connected to 
the REMOTE OUT terminal on the other projector, the two 
projectors can be controlled together by using the emote 
control. (Up to two projectors can be controlled.)
REMOTE IN
REMOTE OUT
REMOTE IN
REMOTE
INREMOTE
OUTINPUT 1
INPUT 2R/PRB/PBG/Y H/HVV
AUDIO
IN
AUDIO
OUTY
CRS-232C RS-232C/MOUSEUSB
S-VIDEO
VIDEO
2
VIDEO
1
L
AUDIO
R MAIN
AC IN
•When the remote control is connected
with remote control cable, it does not
work as a wireless remote control.
•When you need a longer cable, use a pin-
pin cable.
•When using the wired remote control, the
laser beam may be darker. It is normal.
Using the remote control
20˚
20˚ 
						

							EN – 9
ENGLISH
Installation
Orientation of the projector
Picture size can be set by changing the distance between the screen and the projector.
Front projection
Front projection, ceiling mount
For ceiling mount, you need the ceiling mount kit.
Ask a specialist for installation. For more details,
consult your dealer.
•This warranty does not cover damage caused by
the use of any unrecommended ceiling mount kit
and the installation of the ceiling mount kit at an
improper location.
•When using the ceiling mount, set IMAGE RE-
VERSE in the INSTALLATION menu to MIR-
ROR INVERT. See Page 16.
•Projected images may appear darker when the
unit is used as a ceiling installation than when it
is used in the tabletop position. This does not
signify a product malfunction.
Rear projection
Ask a specialist for installation.  For more details,
consult your dealer.
•For rear projection, set IMAGE REVERSE in the
INSTALLATION menu to MIRROR.  See Page 16.
Screen
Caution:
•Placing the projector on a carpet reduces ventila-
tion from the fan at the bottom and might cause
problems. Place a hard board or similar item
under the projector to facilitate ventilation of the
unit.
•Place the projector more than 50 cm (20 inch)
from the wall to prevent blocking the intake,
exhaust slots and ventilation of this projector
because hot air comes out of it.
•Do not use the projector under the following
circumstances, which may cause fire or electric
shock.
•in a dusty or humid place
•while the projector is lying sideways or upside
down
•near a heater
•in a kitchen or oily, smoky or damp place
•in direct sunlight
•with high temperature, such as a closed car
•where the temperature is lower than 41°F
(+5˚C) or higher than 104°F (40˚C).
Important:
•Do not put stress on the lens, as this may cause
damage.
L
 L
I
WW
H
Height
Width
For XL5950U only. About for XL5950LU, please refer to page 30.
•The above numbers are approximate, and may be slightly different from the actual measurements.inch
36
48
60
90
120
150
180 cm
122
163
203
305
406
508
610 inch
60
80
100
150
200
250
300inch
48
64
80
120
160
200
240m
2.3
3.0
3.8
5.8
7.7
9.7
11.6m
2.9
3.9
4.9
7.9
9.8
12.3
- inch
89
120
150
227
304
381
458inch
114
152
191
289
386
483
- cm
91
122
152
229
305
381
457 cm
152
203
254
381
508
635
762
ScreenDistance from the screen : L
Maximum
zoom (WIDE)Minimum
zoom (TELE)Diagonal sizeWidthHeight
cm
4.6
6.1
7.6
11.4
15.2
19.1
22.9cm
42.0
55.8
69.5
103.8
138.1
172.4
206.6 inch
1.8
2.4
3.0
4.5
6.0
7.5
9.0inch
16.6
22.0
27.4
40.9
54.4
67.9
81.4
Lens shift height
Standard : I
Movement
Distance : H
cm
6.2
8.3
10.3
15.4
20.5
25.5
30.6 inch
2.5
3.3
4.1
6.1
8.1
10.1
12.1
Lens shift
width : W
Front projection, ceiling mount
L
WWWidth
Height
H
I
LProjectable image area
Lens center 
						

							EN – 10
Basic connections
This projector can be connected with various devices such as a VCR, video camera, videodisc player, and personal
computer that have analog RGB output connectors.
Important:
•Make sure that the connected device is turned off before starting connection.
•Plug in the projector and the connected devices firmly, and unplug them by holding and pulling out their
power plugs, not by pulling the power cords.
•When the projector and the connected devices are located too close to each other, the projected image may be
affected by their interference.
•See the owner’s guide of each device for details about their connections.
Projector + AV device
Important:
•Connect the video and audio plugs of the AV cable to the proper terminals matching their colors respectively.
•When the connected AV device uses a BNC connector for its video output, connect it to the VIDEO 1 (BNC)
terminal. When both the VIDEO 1 (BNC) terminal and the VIDEO 2 (RCA) terminal are engaged at the same
time, the image supplied to the VIDEO 2 (RCA) terminal takes priority.
•When the connected AV device uses a BNC connector for its S-video output, connect it to the VIDEO 2
(Y,C)(BNC) terminal. When both the VIDEO 2 (Y,C) (BNC) terminal and the S-VIDEO 2 terminal are engaged
at the same time, the image supplied to the S-VIDEO 2 terminal takes priority.
B 
G 
R/PR  G/Y  B/P
B 
R 
CB(PB)
Y
C
R(PR) 
DVD player or HDTV decoder
BNC-RCAconnector
(option)
BNC-BNC cable (option)
AUDIO cable (option)COMPUTER AUDIO IN
to AUDIO OUT
Projector + DVD player or HDTV decoder
Some DVD players have an output connector for 3-line fitting (Y, CB, CR). When connecting such a DVD player
with this projector, use the COMPUTER/COMPONENT VIDEO INPUT 1  terminal.
•The terminals’ names Y, P
B, and PR are examples of a case where a HDTV decoder is connected.
•The terminals’ names are different depending on the connected devices.
•Use BNC-BNC cables for connection.
•The image may not be projected correctly with some DVD players.
•When connecting a HDTV decoder having RGB output terminals, set the COMPUTER INPUT to RGB in the
SIGNAL menu.
To S-video input To S-video output
To video input
To audio inputTo video output To audio output
VCR, etc. S-VCR, etc.
To Y input
To S input To Y output
To S output
To audio inputTo video output To audio output
VCR, etc. S-VCR, etc.
To video input
When using the video (RCA) or S-video connectorWhen using the BNC connector