Mitsubishi Xd95u Data Projector User Manual

							EN-11
ENGLISH
Positioning your projector
Choosing a location
Your room layout or personal preference will dictate which installation location you select. Take into consideration 
the size and position of your screen, the location of a suitable power outlet, as well as the location and distance 
between the projector and the rest of your equipment.
Your projector is designed to be installed in one of the possible installation locations: 
Obtaining a preferred projected image size
The distance from the projector lens to the screen, the zoom setting (if available), and the video format each factors in 
the projected image size.
4:3 is the native aspect ratio of this projector. To be able to project a complete 16:9 (widescreen) aspect ratio image, 
the projector can resize and scale a widescreen image to the projectors native aspect width. This will result in a 
proportionally smaller height equivalent to 75% of the projectors native aspect height.
Thus, a 16:9 aspect image will not utilize 25% of the height of a 4:3 aspect image displayed by this projector. This 
will be seen as darkened (unlit) bars along the top and bottom (vertical 12.5% height respectively) of the 4:3 
projection display area whenever displaying a scaled 16:9 aspect image in the vertical center of the 4:3 projection 
display area.
The projector should always be placed horizontally level (like flat on a table), and positioned directly perpendicular 
(90° right-angle square) to the horizontal center of the screen. This prevents image distortion caused by angled 
projections (or projecting onto angled surfaces). 
The modern digital projector does not project directly forward (like older style reel-to-reel film projectors did). 
Instead, digital projectors are designed to project at a slightly upward angle above the horizontal plane of the 
projector. This is so that they can be readily placed on a table and will project forward and upwards onto a screen 
positioned so that the bottom edge of the screen is above the level of the table (and everyone in the room can see the 
screen).
You can see from the diagram on page 13, that this type of projection causes the bottom edge of the projected image to 
be vertically offset from the horizontal plane of the projector.
If the projector is positioned further away from the screen, the projected image size increases, and the vertical offset 
also increases proportionately.
When determining the position of the screen and projector, you will need to account for both the projected image size 
and the vertical offset dimension, which are directly proportional to the projection distance.
Mitsubishi has provided a table of 4:3-aspect-ratio screen sizes to assist you in determining the ideal location for your 
projector. There are two dimensions to consider, the perpendicular horizontal distance from the center of the screen 
(projection distance), and the vertical offset height of the projector from the horizontal edge of the screen (offset).
1. Front Table
Select this location with the projector placed near the floor in front of the screen. This 
is the most common way to position the projector for quick setup and portability.
2. Rear Table
Select this location with the projector placed near the floor behind the screen.
Note that a special rear projection screen is required.
Set Rear Table in the SYSTEM SETUP: Basic > Projector Position menu after 
you turn the projector on.
4:3 aspect image in a 4:3 
aspect display area16:9 aspect image scaled to 
a 4:3 aspect display area 
						

							EN-12
How to determine the position of the projector for a given screen size
1. Select your screen size.
2. Refer to the table and find the closest match to your screen size in the left columns labeled Screen. Using this 
value, look across this row to the right to find the corresponding average distance from screen value in the 
column labeled Distance from the screen. This is the projection distance.
3. On that same row, look across to the right column and make note of the Hd value. This will determine the final 
vertical offset placement of the projector in relation to the edge of the screen.
4. The recommended position for the projector is aligned perpendicular to the horizontal center of the screen, at the 
distance from the screen determined in step 2 above, and offset by the value determined in step 3 above.
For example, if you are using a 100-inch screen, distance from the screen is 3.8 m and with a vertical offset of 19 cm 
at Zoom position wide.
If you place the projector in a different position (to that recommended), you will have to tilt it down or up to center the 
image on the screen. In these situations, some image distortion will occur. Use the Keystone function to correct the 
distortion. See Correcting keystone on page 22 for details.
How to determine the recommended screen size for a given distance
This method can be used for situations where you have purchased this projector and would like to know what screen 
size will fit in your room.
The maximum screen size is limited by the physical space available in your room. 
1. Measure the distance between the projector and where you want to position the screen. This is the projection 
distance.
2. Refer to the table and find the closest match to your measurement in the distance from the screen column. If the 
min and max values are available on the table, check that your measured distance is between the min and max 
distances listed on either side of the average distance value.
3. Using this value, look across that row to the left to find the corresponding Screen. That is the projected image 
size of the projector at that projection distance.
4. On that same row, look across to the right column and make note of the Hd value. This will determine the final 
placement of the screen in relation to the horizontal plane of the projector. 
For example, if your measured projection distance was 4.0 m, the closest match in the Distance from the screen 
column is from 3.8m to 4.2m. Looking across this row shows that a 100-inch screen is required. 
						

							EN-13
ENGLISH
Layout of the projector
Image size varies depending on the distance between the screen and the projector.
Front projection
(Standard)
(16:9)
There is 3% tolerance among these numbers due to optical component variations. Mitsubishi recommends that if you intend to 
permanently install the projector, you should physically test the projection size and distance using the actual projector in suit 
before you permanently install it, so as to make allowance for this projectors optical characteristics. This will help you 
determine the exact mounting position so that it best suits your installation location.
Screen Distance from the screen : L
Hd
Diagonal Size Width : W Height : H Shortest (WIDE) Longest (TELE)
inch cm inch cm inch cm inch m inch m inch cm
40 102 32 81 24 61 61 1.5 67 1.7 3 8
60 152 48 122 36 91 91 2.3 100 2.5 5 11
80 203 64 163 48 122 121 3.1 133 3.4 6 15
100 254 80 203 60 152 151 3.8 167 4.2 8 19
150 381 120 305 90 229 227 5.8 250 6.3 11 29
200 508 160 406 120 305 303 7.7 - - 15 38
Screen Distance from the screen : L
Hd
Diagonal Size Width : W Height : H Shortest (WIDE) Longest (TELE)
inch cm inch cm inch cm inch m inch m inch cm
40 102 35 89 20 50 66 1.7 73 1.9 7 18
60 152 52 133 29 75 99 2.5 109 2.8 11 27
80 203 70 177 39 100 132 3.4 146 3.7 14 36
100 254 87 221 49 125 166 4.2 182 4.6 18 45
150 381 131 332 74 187 248 6.3 273 6.9 26 67
200 508 174 443 98 249 331 8.4 - - 35 90
W
L
HdH
B A
A=B
L : Between the screen and the front edge of the projector
Hd : Height of the projected image 
						

							EN-14
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted. 
In the connections shown below, some cables may not be included with the projector. They are commercially available from 
electronics stores.
Connecting a computer
The projector provides a VGA input socket that allows you to connect it to both IBM® compatibles and Macintosh® 
computers. A Mac adapter is needed if you are connecting legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
1. Take the supplied VGA cable and connect one end to the D-Sub output socket of the computer.
2. Connect the other end of the VGA cable to the D-SUB/COMP. IN signal input socket on the projector.
The final connection path should be like that shown in the following diagram:
Many notebooks do not turn on their external video ports when connected to a projector. Usually a key combo like FN + F3 or 
CRT/LCD key turns the external display on/off. Locate a function key labeled CRT/LCD or a function key with a monitor symbol 
on the notebook. Press FN and the labeled function key simultaneously. Refer to your notebooks documentation to find your 
notebooks key combination.
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one of the following output sockets:
• Component Video
•S-Video
• Video (composite)
You need only connect the projector to a Video source device using just one of the above connecting methods, 
however each provides a different level of video quality. The method you choose will most likely depend upon the 
availability of matching terminals on both the projector and the Video source device as described below:
Best video quality
The best available video connection method is Component Video (not to be confused with composite Video). Digital 
TV tuner and DVD players output Component Video natively, so if available on your devices, this should be your 
connection method of choice in preference to (composite) Video.
See Connecting a Component Video source device on page 15 for how to connect the projector to a component 
video device.
Better video quality
The S-Video method provides a better quality analog video than standard composite Video. If you have both 
composite Video and S-Video output terminals on your Video source device, you should elect to use the S-Video 
option.
See Connecting an S-Video source device on page 15 for how to connect the projector to an S-Video device.
Least video quality
Composite Video is an analog video and will result in a perfectly acceptable, but less than optimal result from your 
projector, being the least video quality of the available methods described here.
See Connecting a composite Video source device on page 16 for how to connect the projector to a composite Video 
device.
Notebook or desktop computer
VGA cable 
						

							EN-15
ENGLISH
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component Video output sockets available: 
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:
1. Take a Component Video to VGA (D-Sub) adaptor cable and connect the end with 3 RCA type connectors to the 
Component Video output sockets of the Video source device. Match the color of the plugs to the color of the 
sockets; green to green, blue to blue, and red to red.
2. Connect the other end of the Component Video to VGA (D-Sub) adaptor cable (with a D-Sub type connector) to 
the D-SUB/COMP. IN socket on the projector.
The final connection path should be like that shown in the following diagram:
If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, 
check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected 
correctly.
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video output socket available: 
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an S-Video source device:
1. Take an S-Video cable and connect one end to the S-Video output socket of the Video source device.
2. Connect the other end of the S-Video cable to the S-VIDEO socket on the projector.
The final connection path should be like that shown in the following diagram:
• If the selected video image is not displayed after the projector is turned on and the correct video source has been 
selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have 
been connected correctly.
• If you have already made a Component Video connection between the projector and this S-Video source device, you need 
not connect to this device using an S-Video connection as this makes an unnecessary second connection of poorer 
picture quality. See Connecting Video source devices on page 14 for details.
AV device
Component Video to 
VGA (D-Sub) adaptor 
cable 
AV  d e v i c e
S-Video cable 
						

							EN-16
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite Video output sockets available: 
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a composite Video source device:
1. Take a Video cable and connect one end to the composite Video output socket of the Video source device.
2. Connect the other end of the Video cable to the VIDEO socket on the projector.
The final connection path should be like that shown in the following diagram:
• If the selected video image is not displayed after the projector is turned on and the correct video source has been 
selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have 
been connected correctly.
• You need only connect to this device using a composite Video connection if Component Video and S-Video inputs are 
unavailable for use. See Connecting Video source devices on page 14 for details.
AV device
Video cable  
						

							EN-17
ENGLISH
Operation
Starting up the projector
1. Plug the power cord into the projector and into a wall socket. Turn on the 
wall socket switch (where fitted). Check that the POWER indicator light 
on the projector lights orange after power has been applied.
• Ask your installation specialist to provide an Earth leakage breaker. When you do 
not use the projector, be sure to shut down the main power by the breaker.
2. Remove the lens cap. If it is closed, it could become deformed due to the 
heat produced by the projection lamp.
3. Press Power on the projector or remote control to start the projector. 
The POWER indicator light flashes green and stays green when the 
projector is on.
The start up procedure takes about 30 seconds. In the later stage of start up, 
a startup logo is projected.
(If necessary) Rotate the focus ring to adjust the image clearness.
• If the projector is still hot from previous activity, it will run the cooling fans for 
approximately 90 seconds before energizing the lamp.
• To maintain the lamp life, once you turn the projector on, wait at least 5 minutes 
before turning it off.
4. If you are prompted for a password, press the arrow keys to enter a six-digit password. See Utilizing the 
password function on page 19 for details.
5. Switch all of the connected equipment on.
6. The projector will start to search for input signals. The current input signal being scanned displays in the upper 
left corner of the screen. If the projector doesnt detect a valid signal, the message No Signal will continue 
displaying until an input signal is found.
You can also press SOURCE on the projector or remote control to select your desired input signal. See Switching 
input signal on page 20 for details.
If the frequency/resolution of the input signal exceeds the projectors operating range, you will see the message Out of Range 
displayed on a blank screen. Please change to an input signal which is compatible with the projectors resolution or set the 
input signal to a lower setting. See Timing chart on page 43 for details.
II 
						

							EN-18
Using the menus
The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings.
Below is the overview of the OSD menu.
To use the OSD menus, please set them to your familiar language first.
1. Press MENU on the projector or remote control 
to turn the OSD menu on.3. Press   to highlight Language and press  /  
to select a preferred language.
2. Use  /  to highlight the SYSTEM SETUP: 
Basic menu.4. Press MENU twice* on the projector or remote 
control to leave and save the settings.
*The first press leads you back to the main menu and 
the second press closes the OSD menu.
Current input signal
Main menu icon
Main menu
Sub-menu
Highlight
Press MENU 
to go back to 
the previous 
page or to 
exit.Status
DISPLAY
Wall Color
Aspect Ratio
Keystone
Phase
H. Size
MagnifyOff
Auto
16
0
MENU ExitAnalog RGB
Position ENTER
DISPLAYWall Color
Aspect Ratio
Position
Phase
H. Size
MagnifyOff
Auto
MENU Exit
Keystone
16
0
Analog RGB
SYSTEM SETUP: BasicPresentation Timer
Projector Position
Auto Power Off
Blank Timer
Timer Controller Panel Key Lock
Splash Screen
Analog RGBMENU Exit
Front Table
Disable
Disable
Off
Disable
MITSUBISHIEnglish Language
SYSTEM SETUP: BasicPresentation Timer
English Language
Projector Position
Auto Power Off
Blank Timer
Timer Controller Panel Key Lock
Splash Screen
Analog RGBMENU Exit
Front Table
Disable
Disable
Off
Disable
MITSUBISHI 
						

							EN-19
ENGLISH
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password 
security. The password can be set through the On-Screen Display (OSD) menu. For details of the OSD menu 
operation, please refer to Using the menus on page 18.
You will be inconvenienced if you activate the power-on lock functionality and subsequently forget the password. Print out this 
manual (if necessary) and write the password you used in this manual, and keep the manual in a safe place for later recall.
Setting a password
Once a password has been set, the projector cannot be used unless the correct password is entered every time the projector is 
started.
1. Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security Settings menu. Press MODE/
ENTER. The Security Settings page displays.
2. Highlight Power on lock and select On by pressing  / .
3. As pictured to the right, the four arrow keys ( ,  ,  ,  ) respectively 
represent 4 digits (1, 2, 3, 4). According to the password you desire to set, 
press the arrow keys to enter six digits for the password.
4. Confirm the new password by re-entering the new password.
Once the password is set, the OSD menu returns to the Security Settings page.
The digits being input will display as asterisks on-screen. Write your selected 
password down here in this manual in advance or right after the password is entered so 
that it is available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this manual in a safe place.
5. To leave the OSD menu, press MENU.
If you forget the password
If the password function is activated, you will be asked to enter the six-digit 
password every time you turn on the projector. If you enter the wrong password, 
the password error message as pictured to the right displays lasting for three 
seconds, and the message INPUT PASSWORD follows. You can retry by 
entering another six-digit password, or if you did not record the password in this 
manual, and you absolutely do not remember it, you can use the password recall 
procedure. See Entering the password recall procedure on page 19 for details.
If you enter an incorrect password 5 times in succession, the projector will automatically shut down in a short time.
Entering the password recall procedure
1. Press and hold AUTO on the projector or remote control for 3 seconds. 
The projector will display a coded number on the screen.
2. Write down the number and turn off your projector.
3. Please obtain a password using the Mitsubishi Password Decoder Software 
Operation Manual included in this CD.
INPUT NEW PASSWORD
Back MENU
Please write down the recall code, 
and contact Mitsubishi 
Customer Center.
Recall code:
0 2 1 2 RECALL PASSWORD
Exit MENU 
						

							EN-20
Changing the password
1. Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security Settings > Change password 
menu.
2. Press MODE/ENTER. The message INPUT CURRENT PASSWORD displays.
3. Enter the old password.
• If the password is correct, another message INPUT NEW PASSWORD displays.
• If the password is incorrect, the password error message displays lasting for three seconds, and the message 
INPUT CURRENT PASSWORD displays for your retry. You can press MENU to cancel the change or try 
another password.
4. Enter a new password.
The digits being input will display as asterisks on-screen. Write your selected password down here in this manual in advance or 
right after the password is entered so that it is available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this manual in a safe place.
5. Confirm the new password by re-entering the new password.
6. You have successfully assigned a new password to the projector. Remember to enter the new password next time 
the projector is started.
7. To leave the OSD menu, press MENU.
Disabling the password function
To disable password protection, go back to the SYSTEM SETUP: Advanced > Security Settings > Power on lock 
menu after opening the OSD menu system. Select Off by pressing  /. The message INPUT PASSWORD 
displays. Enter the current password. 
• If the password is correct, the OSD menu returns to the Security Settings page with Off shown in the row of 
Power on lock. You will not have to enter the password next time you turn on the projector.
• If the password is incorrect, the password error message displays lasting for three seconds, and the message 
INPUT PASSWORD displays for your retry. You can press MENU to cancel the change or try another 
password.
Though the password function is disabled, you need to keep the old password in hand should you ever need to re-activate the 
password function by entering the old password.
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a 
time. 
Be sure the Quick Auto Search function in the SOURCE menu is On (which is the default of this projector) if you 
want the projector to automatically search for the signals.
You can also manually cycle through the available input signals.
1. Press SOURCE on the projector or remote control. A source selection 
bar displays. 
2. Press  /  until your desired signal is selected and press MODE/
ENTER.
Once detected, the selected source information will display on the screen for 
seconds. If there is multiple equipment connected to the projector, repeat 
steps 1-2 to search for another signal.
• The brightness level of the projected image will change accordingly when you 
switch between different input signals. Data (graphic) PC presentations using 
mostly static images are generally brighter than Video using mostly moving 
images (movies).
• The input signal type effects the options available for the Setting. See 
Selecting a picture mode on page 24 for details.
• The native display resolution of this projector is in a 4:3 aspect ratio. For best 
display picture results, you should select and use an input signal which 
outputs at this resolution. Any other resolutions will be scaled by the projector depending upon the aspect ratio setting, 
which may cause some image distortion or loss of picture clarity. See Selecting the aspect ratio on page 23 for details.D-Sub / Comp.
Video
S-Video