Mitsubishi Xd60u Data Projector User Manual

E-20
Connecting Personal Computers and Video Equipment
Connections with Audio Connectors
* Make the connection to the projector’s AUDIO connector using the supplied audio cable. When the audio jack of the equipment
that is to be connected is of the RCA phono type, make connection via the supplied audio conversion cable.
* The built-in speaker of the projector provides monaural audio. To enjoy convincing audio reproduction, please connect the
audio output of the video equipment to your audio system.
* The...

E-21
Power Cable Connections and Switching the Power On/Off
DVI AUDIO VIDEO
S-VIDEO
STATUS
SOURCESTANDBY
AUTO
MENUQUICK
MENU
MO
USE
STATUS STANDBYSTATUS STANDBYSTATUS STANDBY
There is an order in which the power cable is connected and the power is switched on/off.
Operating
1Connect the AC IN connector of the projector and the power outlet using the supplied power cable.The STANDBY indicator will light in amber, and the unit will enter the standby mode.
Firmly plug in all the way.
To wall outlet
2Switch...

E-22
Power Cable Connections and Switching the Power On/Off
When [Menu Language Select] is Displayed Upon Switching On the Power
The first time the power is switched on after purchase, [Menu Lan-
guage Select] will be displayed. Follow the procedure described be-
low and select the display language of the projector.
If the image is blurred, turn the focus ring counterclockwise or clock-
wise to focus it. See Page E-25.
1Press the SELECT 
 buttons of the projector and
align the deep blue cursor with...

E-23
Power Cable Connections and Switching the Power On/Off
RGB
STANDBY
VIDEO
FREEZE
MUTELAMP MODE AUTO
ASPECT
CANCEL QUICKMENU
ENTERQ
1234
Finishing
1Switch off the power of the connected equipment
2Switch off the power of the projector
Main unit operation: Press the STANDBY button.
Remote control operation: Press the STANDBY button.
Warrning
Do not unplug the power cable while the STANDBY indicator is blinking amber. Doing so may shorten the life of the lamp
or damage the projector.
Power OffOK ?
The...

E-24
Adjustment of the Projection Screen
Switch on the power of the connected equipment and make the adjustments with the video signal being input to the
projector.
Adjustment of the Projection Screen
2Adjust the projection image to the screen.Check that the screen is set level and vertically.
(1) If the image is shifted to the left or right, move the main unit horizontally. (Align the center of the screen and the center of
the projector lens.)
(2) If the image is shifted vertically, move the image up or...

E-25
Adjustment of the Projection Screen
XD60
(
1)STATUS
SOURCESTANDBY
AUTO
MENUQUICK
MENU
(
1)
(
2)
DVI
AUDIO
VIDEO
S-VIDEO
MOUSE
STATUS
SOURCESTANDBY
AUTO
MENUQUICK
MENU
3Turn the focus ring and adjust the focus of the screen
Focus ring
Making Adjustments with the Adjusters
Raising the projection image
While viewing the projection image, (1) press and hold
the front adjuster buttons located at the left and right and,
(2) raise the projector to align the image with the screen,
then release your...

E-26
General Operation
This section describes the use of direct operation with the main unit or remote control buttons.
For information about operation using the menu, see Menu Operation Method on Page E-35 and the various items on
Pages E-42 to E-54.
Input Selection
This operation selects the input signal to be projected.
Main unit operation: Press the SOURCE button.
(It will not function while the menu or the quick menu is displayed.)
When Auto Source is On
If there is no input signal at the source...

E-27
General Operation
Selection of Aspect Ratio
This function selects horizontal and vertical picture proportions of the input
signal.
Press the ASPECT button while viewing the projected image and select the
aspect ratio.
Personal Computer Signal
Each press of the ASPECT button advances the selection one step in the se-
quence of Auto → Direct → Real, and then repeats.
Auto ............ Automatically enlarges or reduces the image to project a full screen in a ratio
of 4:3
Direct .......... Maintains the...

E-28
Freezing a Moving Picture
This function is used to stop and view a moving picture. Note that the input
image continues to advance even though the picture there is a still picture
condition.
A press of the FREEZE button changes the screen to a still picture. A
further press returns the screen to a moving picture.
General Operation
RGB
STANDBY
VIDEO
MUTELAMP MODE AUTO
ASPECT
TIMER VOL KSTN ZOOMCANCEL QUICKMENU
ENTERQ
234FREEZE1
Cancelling Video and Audio Temporarily
This function is used to cancel the...

E-29
Keystone
Use this to adjust for trapezoidal (keystone) distortion of the pro-
jected image.
Adjustment Method
(1) Press the 
 or  KSTN button to make the left and right sides
parallel.
The keystone adjustment display appears when one of the buttons is
pressed.
(2) Press the CANCEL button to immediately close the display.
The display will close when there has not been an operation in about
10 seconds.
Note:
* Keystone adjustment values can be saved. See “Keystone Save” on Page
E-48.
* Screen...