Mitsubishi Xd530u Data Projector User Manual

							EN-11
ENGLISH
Basic connections
This projector can be connected with various devices such as a VCR, video camera, videodisc player, and personal computer that have analog RGB 
output connectors. 
Important:  Make sure that the connected device is turned off before starting connection. 
 Plug in the power cords of the projector and the connected devices firmly. When unplugging, hold and pull the plug. Do not pull the cord. 
 When the projector and the connected devices are located too close to each other, the projected image may be affected by their interference. 
 See the owner’s guide of each device for details about its connections. 
Projector + AV device 
Important:  Match the colors of the video and audio plugs on the Audio cable with those of the terminals.
 Speaker output is mono. 
S-VIDEO IN
(option)
AUDIO-IN
(option)
to audio output (R)
to audio output (L)
to S-video output VCR, etc.AUDIO-R
AUDIO-L(option)* A mini-plug audio cable can also be used. 
						

							EN-12
Basic connections (continued)
Projector + DVD player or HDTV decoder Some DVD players have an output connector for 3-line fitting (Y, CB, CR). When connecting such DVD player with this projector, use the
COMPUTER-IN terminal. 
Important:  The terminal’s names Y, PB, and PR are given as examples of when a HDTV decoder is connected. 
 The terminal’s names vary depending on the connected devices. 
 Use a Mini D-SUB 15-pin - BNC conversion cable for connection. 
 Image may not be projected correctly with some DVD players. 
 When connecting a HDTV decoder having RGB output terminals, set COMPUTER INPUT to RGB in the SIGNAL menu. 
 Speaker output is mono.
 Only the RGB signal is supported. Color difference signals are not supported.
BR
DVD player or HDTV decoderAudio cable (option)
to audio output
BNC - RCA connector (option)
No connection
COMPUTER-IN
Mini D-SUB 15-pin - BNC conversion 
cable (option) 
						

							EN-13
ENGLISH
Basic connections (continued)
Projector + Computer 
For computer with Mini D-SUB or DVI-D  
For analog connection: 
1. Connect one end of the supplied RGB cable to the COMPUTER-IN terminal (1, 2) of the projector.
2. Connect the other end of the RGB cable to the monitor port of the computer. 
For digital connection:
1. Connect one end of the DVI-D cable to the DVI-D (HDCP) terminal of the projector.
2. Connect the other end of the DVI-D cable to the monitor port of the computer.
 If you start the computer first, images may not be displayed.
 The DVI-D (HDCP) terminal of this projector supports DDC2B. If the projector is connected to a computer which supports the standard, the com-
puter automatically reads out the information about the projector to output appropriate images.
 If the projector is connected to a computer which supports DDC, plug the power plug of the projector into the wall outlet, and then start the com-
puter.
 The DVI type that the projector supports is DVI-D (digital). DVI-A (analog) cannot be used with the projector.
 If a computer has a DVI-I (digital and analog) output connector, you can connect the projector with a DVI-D cable.
 Use the AUDIO-IN terminal for the audio input.
For monitor connection:Connect the RGB cable from the monitor to the MONITOR OUT terminal of the projector.
 Images may not be displayed correctly depending on the type of the input signal. See the instruction manual of the monitor.
 Signals are coming from the COMPUTER-IN terminal (1 or 2) of the projector.
 When signals are coming from both COMPUTER-IN terminals (1, 2), images are projected from the terminal (1 or 2) currently or last selected in 
the projectors menu.
Important:  When you use a longer RGB cable instead of the provided cable, the image may not be projected correctly. 
 Some computers require additional connectors or analog RGB output adapters to be connected with this projector. Contact your dealer for fur-
ther information. 
 This projector uses stereo pin jack for its audio input. Check the type of the audio output terminal of the connected computer and prepare a 
proper cable for connection. Some computers don’t have the audio output terminal. 
 Speaker output is mono. 
 When the audio cable is connected to the AUDIO-OUT terminal, the speaker output is muted. 
 While the DVI-D terminal is being used or while an image is being projected wirelessly, you cannot use the MONITOR OUT terminal.
For Macintosh  If your Macintosh has no video port, a monitor output adapter is required. Contact your dealer for further information. 
 Some Macintoshes require a MAC adapter for the RGB cable for connection with this projector. Contact your dealer for further information. 
About DDCThe COMPUTER/COMPONENT VIDEO IN-1 terminal of this projector complies with the DDC 1/2B standard. When a computer supporting this 
standard is connected to this terminal, the computer will automatically load the information from this projector and prepare for output of appropriate 
images.
 After connecting a computer supporting this standard to this terminal, plug the power cord of the projector in the wall outlet first, and then boot up 
the computer.
AUDIO OUT
MONITOR OUTPUT DVI-D
COMPUTER-INRGB cable for PC
AUDIO-OUT
Audio cable (option) MONITOR OUT
Necessary when outputting to both 
a PC monitor and the projector.
PC audio cable (option)
AU DI O- I N
to PC audio outputComputerto monitor port
RGB cable for PC (option)DV I - D  c a bl e  fo r  P C
DVI-D (HDCP)to DVI-D port 
						

							EN-14
Preparation
Preparation for projection 1. Attach the provided power cord to the projector. 
2. Plug the power cord in the wall outlet. 
3. Remove the lens cap. 
Warning:  Do not look into the lens directly when the projector is on. 
 The lens cap is for protecting the lens. If you leave the lens cap on 
the lens with the projector turned on, it may be deformed because 
of heat build-up. Remove the lens cap when you turn on the pro-
jector. 
 One of power cords for the U.S., Europe and U.K. is provided 
appropriately.
 This projector uses the power plug of three-pin grounding type. Do 
not remove the grounding pin from the power plug. If the power 
plug doesn’t fit your wall outlet, ask an electrician to change the 
wall outlet. 
 In case that the power cord for the U.S is provided with this projec-
tor, never connect this cord to any outlet or power supply using 
other voltages or frequencies than rated. If you want to use a 
power supply using other voltage than rated, prepare an appropri-
ate power cord separately.
 Use 100-240 V AC 50/60 Hz to prevent fire or electric shock. 
 Do not place any objects on the power cord or do not place the 
projector near heat sources to prevent damage to the power cord. 
If the power cord should be damaged, contact your dealer for 
replacement because it may cause fire or electric shock. 
 Do not modify or alter the power cord. If the power cord is modified 
or altered, it may cause fire or electric shock. 
Caution:  Plug in the power cord firmly. When unplugging, hold and pull the 
power plug, not the power cord. 
 Do not plug in or out the power cord with your hand wet. It may 
cause electric shock. 
Adjustment of the projection angle For the best projection, project images on a flat screen installed at 90 
degrees to the floor. If necessary, tilt the projector using the two 
adjustment feet on the bottom of the projector.
Using the adjustment feet (front)1. Tilt up the projector to the appropriate angle.
2. Press the foot adjustment button (front).
3. Release the foot adjustment button (front) after fine adjusting a 
position of lengthwise direction of the image.
 
After using the projector: 
4. Put the adjustment feet (front) back into the projector by pressing 
the foot adjustment buttons. 
Using the adjustment feet (rear)1. Tilt up the projector to the appropriate angle. 
2. Rotate the adjustment feet (rear) for fine adjustment. 
Important:  Install the screen on a flat wall at 90 degrees to the floor. 
 Slanting the projector more than ±10° (right and left) or ±15° (front 
and rear) may cause trouble or explosion of the lamp. You can tilt 
the projector up to 8 degrees using the adjustment feet only. 
 Images may not be projected in a shape of a regular rectangle or 
with its aspect ratio 4:3, depending on the installation conditions of 
the projector and the screen. 
 To correct vertical keystone distortion, press the KEYSTONE but-
ton on the projector or the remote control to display KEYSTONE, 
and adjust the image by pressing the S, T button (or VOLUME 
S, T button on the remote control). 
In the following cases:  
Important: 
 When the keystone adjustment is carried out, the adjustment 
value is indicated. Note that this value doesn’t mean a projection 
angle. 
 The allowable range of the adjustment value in the keystone 
adjustment varies depending on the installation conditions. 
 When the keystone adjustment takes effect, the resolution 
decreases. In addition, stripes may appear or straight lines may 
bend in images with complicated patterns. They are not due to 
product malfunctions. 
 Noise may appear on the screen during the keystone adjustment 
because of the type of the video signal being projected and the 
setting values of the keystone adjustment. In such cases, set the 
keystone adjustment values in the range where the image is dis-
played without noise. 
 When the keystone adjustment is carried out, the image may not 
be displayed correctly because of the type of input signal.
Foot adjustment button
Press the T  
button.Press the S  
button. 
						

							EN-15
ENGLISH
Basic operation
Power-on 1. Turn on the device connected to the projector first. 
2. Plug the power cord in the wall outlet. 
 The POWER indicator lights up. 
 If the power cord is unplugged from the wall outlet before the 
projector is cooled down completely after use, the fans may 
start rotating when the power cord is plugged in next time 
and the POWER button may not function. In this case, wait 
for the fans to stop and press the POWER button to light the 
indicator. 
3. Press the POWER button on the control panel or the ON button 
on the remote control. 
 It may take about one minute for the lamp to light up. 
 The lamp occasionally fails to light up. Wait a few minutes 
and try to light the lamp again. 
 After the POWER button is pressed, the image may flicker 
before the lamp becomes stable. This is not a product mal-
function. 
 Regardless of the setting of LAMP MODE in the INSTALLA-
TION menu, the STANDARD lamp mode is activated by 
default. The LAMP MODE is set to either STANDARD or 
LOW depending on the setting last selected, and you cannot 
switch the LAMP MODE in about one minute after the lamp 
is on.
Important:  If the lamp exceptionally turned off due to the power interruption or 
voltage drop, it can happen that the lamp does not turn on even if 
you switch again the power supply on. In that case, please pull the 
electric cord out of the consent and put it again in the consent 
about 10 minutes later.
 Do not cover the lens with the lens cap while the lamp is on.
 The projector starts warming up when the POWER button is 
pressed. During the warm-up process, images may appear dark 
and no commands are accepted.  By blinking red, the STATUS indicator indicates that the lamp 
should be replaced soon. Replace the lamp when the STATUS 
indicator blinks red. (See page 42 and 46.) 
 Images may not be projected with good quality in an extremely hot 
or cold environment. (This is not a product malfunction.) 
4. Adjust the focus by turning the focus ring. 
5. Choose your desired external input source using  the COM-
PUTER or VIDEO or DVI button.
 The input source is switched from VIDEO to COMPUTER at 
the press of the COMPUTER button on the control panel.
 The input source is switched between VIDEO and S-VIDEO 
at every press of the VIDEO button on the control panel.
 Each time you press the COMPUTER button on the control 
panel, the input source is switched in the order of COM-
PUTER 1 → COMPUTER 2 → DVI → WIRELESS.
 The projector automatically selects the appropriate signal 
format. The selected signal format is displayed on the 
screen. 
 The COMPUTER and VIDEO buttons don’t function while 
the menu is being displayed. 
 When COMPUTER is chosen as the source, images sup-
plied from the computer may flicker. Press the W or X button 
on the remote control to reduce flicker, if it occurs. 
 To avoid permanently imprinting a fixed image onto your pro-
jector, please do not display the same stationary images for 
long period.
 If you want to project images wirelessly, see page 21.
6. Adjust the image size by turning the zoom ring.
 If necessary, adjust the focus and zoom again.
When fine streaks are seen on projected imagesThis is due to interference with the screen surface and is not a mal-
function. Replace the screen or displace the focus a little.
55
3, 1, 2
4 FOCUS
6 ZOOMSTANDBY ON
ASPECT MAGNIFY
KEYSTONEVO L PA G E
UP
DOWN
MENU
FREEZE AU T O
POSITION
AV
MUTEENTER
1
2COMPUTERVIDEOVIEWER
UNPLUGS-
VIDEO
WIRELESSDV I
5 31, 2
5
Indicator
ConditionSTATUS POWER
Stand-by - Red
When the lamp is on. Green Green 
						

							EN-16
Basic operation (continued)
Power-off Use the following procedure to turn off the projector.
The lamp may deteriorate if the projector is powered off and on 
repeatedly within 30 minutes after the lamp is lighted.
1.Press the POWER button on the control panel or the OFF button 
on the remote control. 
 The message POWER OFF? YES : PRESS AGAIN 
appears on the screen.
 To cancel, press any button except the POWER button. 
(Some buttons on the remote control don’t function for can-
cel.) 
2.Press the POWER button on the control panel or the OFF button 
on the remote control within 10 seconds again. 
 The lamp will go out and the STATUS indicator will start 
blinking. 
 Though the lamp goes out at this second press of the 
POWER button (or OFF button), the air outlet fans continue 
operating for one minute to cool down the lamp. The STATUS 
indicator will stop blinking. 
 After stopping the air outlet fans, if the temperature inside the 
set is still high, the temperature sensor detects it and then 
the air outlet fans may start again.
3.Unplug the power cord. 
 The POWER indicator will go out. 
 If the power cord should be unplugged accidentally while 
either the air inlet fan or the air outlet fans are operating or 
the lamp is on, allow the projector to cool down for 10 min-
utes with the power off. To light the lamp again, press the 
POWER button (or OFF button). If the lamp doesn’t light up 
immediately, repeat pressing the POWER button (or OFF 
button) two or three times. If it should still fail to light up, 
replace the lamp. 
Notice: When storing the projector in the carrying case, the lens should 
face up.
Instant Shut DownYou dont have to wait for the cooling fan to cease operation after pow-
ering off the projector. You can unplug the power cord right after the 
projector is powered off.
 Dont shut down the projector while the STATUS indicator is blink-
ing after the lamp lights up because the lamps life may be short-
ened.
 Dont turn the projector back on right after shutting it down 
because the lamps life may be shortened. (Wait about 10 minutes 
before turning the projector back on.)
 Before shutting down the projector, be sure to close the menu 
screen. If you shut down the projector without closing the menu, 
the setting data of the menu may not be saved.
AUTO POSITION button When the image isn’t projected in the right position with COMPUTER 
selected as the input source, follow the procedure below. 
1. Project a bright image such as the Recycle Bin window on the 
full screen. 
2. If the screen saver is running, turn it off. 
3. Press the AUTO POSITION button. 
 If the image is still not in the right position, adjust the image 
position using the SIGNAL menu. See page 35.
Volume from the speaker Press the VOLUME S or T button to change the volume 
from the speaker.
The volume control bar will appear on the screen.
 The volume control bar will disappear about 10 seconds after the 
VOLUME button is released. 
 The VOLUME buttons don’t function while the menu selection bar 
or the menu is being displayed. 
 When a high-level audio signal, such as a DVD audio signal, is 
supplied to the AUDIO-IN terminal, the output from the speaker 
may be distorted. 
AV  m u t e  The video and audio signals are temporarily muted when the AV 
MUTE button is pressed. To cancel muting, press the AV MUTE button 
again. 
Setting the aspect ratioYou can change the aspect ratio of the input video signal (or the ratio 
of width to height of the image). Change the setting according to the 
type of the input video signal.
How to change the settings:
With the remote control:
1. Press the ASPECT button.
 Every time the ASPECT button is pressed, the aspect mode 
changes from AUTO to 16:9, to FULL, and back to AUTO.
With the FEATURE menu:(See page 34 for menu setting.)
1. Display the FEATURE menu.
2. Select ASPECT by pressing the S or T button.
3. Select your desired aspect ratio by pressing the W or X button.
When 16:9  is selected.
4. Press the ENTER button.
5. Select your desired position (CENTER, UPPER or LOWER) by 
pressing the W or X button.
To cancel the menu:
6. Press the MENU button.
Important: When a 16:9 image is kept displayed for a long time before dis-
playing 4:3 image, the afterimages of the black bars may appear 
on the 4:3 image screen. Consult your dealer in this case.
Caution:  After using the projector, wait one minute for the air outlet fans to 
stop in normal use. Then unplug the power cord from the wall out-
let. 
 The lamp can’t be lit again for one minute after turned off for safety 
purpose. It will take another one minute for the STATUS indicator 
to go out. If you want to turn on the projector again, wait until the 
indicator goes out, and then press the POWER button. 
 The air outlet fans rotate faster as the temperature around the pro-
jector rises. 
 When the temperature around the projector rises high, the sign 
TEMPERATURE!! blinks red on the screen. If the temperature 
stays high, the lamp will go out automatically. 
Important:  Do not display a still picture for a long time because the afterim-
ages may persist on the screen.
VOLUME     10
FEATUREAUTO ASPECT
opt. 
						

							EN-17
ENGLISH
Basic operation (continued)
Wall ScreenThis function is to reproduce natural color tones when images are pro-
jected directly onto a screen or wall surface. You can select from 
BEIGE, LIGHT BLUE, LIGHT GREEN, PINK, BLACK BOARD, WHITE 
BOARD, and OFF, to match the color of the screen or wall to be used 
for projection.
1. Display the INSTALLATION menu. (See page 33 for more details.)
2. Press the S or T button to select WALL SCREEN.
3. Press the W or X button to select the color closest to that of the 
screen on which images are projected.
 When the GAMMA mode setting is changed, images may not 
be displayed correctly.
 When OFF or BLACK BOARD/WHITE BOARD is selected, 
the density cannot be adjusted.
 When WHITE BOARD is selected, BrilliantColor
TM in the 
Color Enhancer menu of the Image menu cannot be used. 
Additionally, Theater in the Color Enhancer menu of the 
Image menu has no effect and is automatically canceled 
when WHITE BOARD is selected.
4. Press the ENTER button.
5. Press the W or X button to adjust the density of the selected 
color.
When connecting to a laptop computer:When this projector is connected to a laptop computer, there may be 
times when images may not be projected. When it occurs, set the 
computer so that it can output signals externally. The procedure varies 
across computers in use. See the instruction manual of your com-
puter.
INSTALLATIONWALL SCREENLAMP MODEBEIGE
STANDARD
opt.
LIGHT BLUE 1 
						

							EN-18
Safety instructions for wireless
The projector operates in a 2.4 GHz band for its wireless LAN capabilities. No license is required for use. Before using the projector, read the follow-
ing instructions thoroughly and carefully and always observe them.
Do not use the wireless function in the vicinity of other wireless appliances.
The following appliances may use the same radio wave band as the projector. If the projector is used in the vicinity of the following appliances, the 
projector may not be able to communicate or the communication speed may drop due to radio wave interference.
 A microwave oven and other appliances
 Industrial, scientific, or medical appliances
 A wireless base station typically installed at factorys manufacturing lines for use in classification of moving objects
 A low-power wireless base station
Wireless LAN signals barely trickle through steel, metal, stone, or concrete.
Wireless LAN signals trickle through wood or glass free of metal mesh. However, when steel, metal, stone, or concrete is used as the wall or floor 
material, the signals barely trickle through it.
Do not place the projector on a carpet, cushion, or bedding that may cause static electricity.
LAN communications, whether they are wired or wireless, may be interrupted when you place the projector on a carpet, cushion, or bedding that 
may cause static electricity. Should you experience such problems, disconnect your connection, try to hold static electricity or remove noise sources, 
and reconnect your connection.
Your connection may not be connected due to static electricity or noise. Should you experience such problems, press the Power button on the con-
trol panel or remote control to turn off the projector. 
In an environment where there are many wireless devices, you may not be able to connect the projector. 
						

							EN-19
ENGLISH
Security precautions for wireless
Because leakage of your privacy information via the projector and abusive manipulation, interference, suspension, etc. of the projector by a mali-
cious third person can be assumed, read the following precautions thoroughly and carefully and take appropriate security measures accordingly 
before using the projector.
Security measures
 Use the WEP encryption equipped with the projector.
 Use the Conference Control mode.
 Specify or change the passwords for the Conference Control mode and network setting to those cannot be easily guessed.
About wireless LAN network
Wireless LAN (WLAN) devices such as cards, routers, and access points provide security features. You can secure your wireless network by 
enabling these security features to use the projector securely. 
						

							EN-20
Software license agreement for wireless
Using the following procedure, you can download and install the software for wireless communication from the projector. Before using the projector, 
read and agree to the terms and conditions of the following software license agreement in advance.
License
The licensee is granted a license to use this software (information downloaded from the wireless projector), but not copyrights and intellectual prop-
erty rights.
Computer Usage
The licensee may run the software on computers that the licensee owns or manages when using the projector.
Modification Restrictions
The licensee shall not evaluate or modify the software.
Mitsubishi Electric Corporation or the licensees dealer shall not be responsible for accidents or damages that may occur as a result of improper use 
or attempts to evaluate or modify the software on the part of the licensee.
After-sales Service
If you have a problem with the software during the use, please contact us by phone or correspondence.
We can give you the required information such as an identified error (bug) and usage improvement for your inquiry. The software specifications may 
be changed without notice.
Limitation of Liability
Our responsibility for the software is limited only to the above after-sales service.
Mitsubishi Electric Corporation or the licensees dealer shall not be responsible for, and shall not pay any amount of incidental, consequential or 
other indirect damages, whether based on lost revenue or otherwise, claimed by the licensee or anyone else.
The licensee shall not use the software without the projector.
 Note in advance that Mitsubishi Electric Corporation holds no responsibility for any data losses, which may occur as a result of using the projec-
tor.
Export Regulations
The software delivered under this agreement may be subject to export regulations in other countries.
The licensee shall agree to comply strictly with these regulations.
Installing software
System Requirements for user computers
The following lists the system requirements.
Operating system: Windows
® 2000 Professional/XP Professional SP2
CPU: Intel® Pentium® III 600 MHz or greater (800 MHz or greater recommended in live mode)
Memory: 256 MB or greater of RAM
Disk space: 60 MB or greater
Hardware: A built-in or external CD or DVD drive required to install and use the software on a computer
A LAN terminal (10BASE-T/100BASE-TX)
A built-in or external 802.11 b/g wireless LAN adaptor for wireless LAN communications
Browser: Internet Explorer 6.0 or higher
Attention! Mitsubishi Electric Corporation holds no responsibility for accidents or damages, whether direct or indirect, which may occur as a result of using a 
computer that does not meet the system requirements described immediately above. Additionally, note in advance that all the operations are not 
guaranteed even in the above system environment.
Precaution for Windows Vista
Although it is possible to download and install the Wireless Projector software on a computer equipped with Windows Vista, note that you may not 
be able to use the software due to the influence of various security programs etc.
Precaution for Macintosh
The wireless function of the projector is not available on Macintosh computers.