Mitsubishi Xd480u Data Projector User Manual

							 EN - 11
ENGLISH
Projector + video equipment having a DVI-D terminal (For XD480U / XD450U only)
You can project high-quality images by connecting the DVI terminal of this projector to video equipment having a 
DVI-D output terminal. In addition, this projector supports HDCP and is able to receive encrypted digital video data 
that are output from DVD players. 
•  For connection to the DVI-D terminal, use a commercially available DVI cable. 
•  Select DVI  as the input source. 
•  Only RGB signals are supported. Component video signals are not supported. 
•  HDCP (High-bandwidth Digital Content Protection), developed by Intel Corporation, is a method to encrypt digital 
video data for the purpose of copy protection. 
•  When DVI is selected as the input source, setting of TINT, SHARPNESS, FINE SYNC., TRACKING, COMPUTER 
INPUT and HOLD is unavailable. 
When you connect this projector and a DVI-Digital device (such as a DVD player) via the DVI terminal, black 
color may appear light and pale, depending on the type of the connected device. 
•  This depends on the black level setting of the connected device. There are two kinds of methods to digitally trans-
fer image data, in which different black level settings are employed respectively. Therefore, the specifi cations of the 
signals output from DVD players differ, depending on the type of the digital data transfer method they use. 
•  Some DVD players are provided with a function to switch the methods to output DVI-Digital signals. When your 
DVD player is provided with such function, set it as follows.
 NORMAL  EXPAND or ENHANCED
•  See the users guide of your DVD player for details. 
•  When your DVD player does not have such function, set BRIGHTNESS of this projector to -8.  
COMPUTER/COMPONENT 
VIDEO DVI-D (HDCP) IN-2
Equipment having a 
DVI-D terminal
to audio outputAudio cable (option)
to DVI-D output 
DVI cable (option)  
						

							EN - 12
Projector + Computer
For computer with Mini D-SUB
•  The signal inputted to the COMPUTER/COMPONENT VIDEO DVI-D (HDCP) IN-2 terminal is not outputted from the 
COMPUTER OUT terminal. 
•  Make sure to connect computer with DVI cable before starting computer. If connecting computer with DVI cable 
after starting the computer, the image signal may not be outputted from DVI terminal of computer.
•  Plug the power cord of the projector in the wall outlet fi rst, and then boot up the computer.
•  When DVI is selected as the input source, setting of SIGNAL menu (except SHUTTER) is unavailable. 
Important:
•  When you use a longer RGB cable instead of the provided cable, the image may not be projected correctly. 
•  Some computers require additional connectors or analog RGB output adapters to be connected with this projector. 
Contact your dealer for further information. 
•  This projector uses stereo pin jack for its audio input. Check the type of the audio output terminal of the connected 
computer and prepare a proper cable for connection. Some computers don't have the audio output terminal.
•  Speaker output is mono.
•  When the audio cable is connected to the AUDIO OUT terminal, the speaker output is muted.
For Macintosh
•  If your Macintosh has no video port, a monitor output adapter is required. Contact your dealer for further information.
•  Some Macintoshes require a MAC adapter for the RGB cable for connection with this projector. Contact your dealer 
for further information.
About DDC
The COMPUTER/COMPONENT VIDEO IN-1 terminal of this projector complies with the DDC1/2B standard and the 
COMPUTER/COMPONENT VIDEO DVI-D (HDCP) IN-2 terminal complies with the DDC2B standard. When a computer 
supporting this standard is connected to this terminal, the computer will automatically load the information from this 
projector and prepare for output of appropriate images. 
•  After connecting a computer supporting this standard to this terminal, plug the power cord of the projector in the 
wall outlet fi rst, and then boot up the computer.
•  You may need to install the DDC driver, depending on the computer you use. In this case, you need to download 
the driver from our Web site. Contact your dealer or Mitsubishi sales offi ce for further information.
AUDIO OUT
MONITOR OUTPUT
COMPUTER/COMPONENT 
VIDEO IN-1/2
AUDIO INAUDIO OUT
MONITOR  OUT
RGB cable for PC 
Computer
to monitor 
port
PC audio cable (option)to PC audio
output RGB cable for PC (option)
Necessary when outputting to both a PC monitor and the projector.
AUDIO OUT
DVI
COMPUTER/COMPONENT 
VIDEO DVI-D (HDCP) IN-2
AUDIO IN
DVI cable
Computer
to DVI port
PC audio cable (option)to PC audio
output
For computer with DVI terminal (For XD480U / XD450U only)
Basic connections (continued)
Audio cable (option) 
						

							 EN - 13
ENGLISH
Preparation
1.  Tilt up the project to the appropriate angle. 
2.  Press the foot adjustment buttons next to the adjust-
ment feet (rear), and the adjustment feet will come 
out. 
3.  Release the buttons to lock the adjustment feet (rear) 
to that position.
4.  Rotate the adjustment feet (rear) for fi ne adjustment.
After using the projector:
5.  Put the adjustment feet (rear) back into the projector 
by pressing the foot adjustment buttons.
Important: 
•  If necessary, rotate the adjustment feet (front) for fi ne 
adjustment. 
•  Install the screen on a fl at wall at 90 degrees to the 
fl oor. 
•  Slanting the projector more than ±10˚ (right and left) 
or ±15˚ (front and rear) may cause trouble or explo-
sion of the lamp. You can tilt the projector up to 7 
degrees using the adjustment feet only.  
•  Images may not be projected in a shape of a regular 
rectangle or with its aspect ratio 4:3, depending on 
the installation conditions of the projector and the 
screen. 
•  To correct vertical and horizontal keystone distortion, 
press the KEYSTONE button on the projector or the 
remote control to display KEYSTONE, and adjust the 
image by pressing the , , 
,  button (or VOL-
UME +, - button on the remote control). 
In the following cases:Preparation for projection
1.  Attach the provided power cord to the projector.
2.  Plug the power cord in the wall outlet. 
3.  Remove the lens cap.
Warning:
•  Do not look into the lens directly when the projector is 
on.
•  The lens cap is for protecting the lens. If you leave 
the lens cap on the lens with the projector turned 
on, it may be deformed because of heat build-up. 
Remove the lens cap when you turn on the projector.
•  The power cords for use in the U.S. and Europe are 
provided with this projector. Use the appropriate 
cord for your country. 
•  This projector uses the power plug of three-pin 
grounding type. Do not remove the grounding pin 
from the power plug. If the power plug doesn't fi t 
your wall outlet, ask an electrician to change the wall 
outlet. 
•  The provided power cord for the U.S. is rated at 120 V. 
Never connect this cord to any outlet or power sup-
ply using other voltages or frequencies than rated. If 
you want to use a power supply using other voltage 
than rated, prepare an appropriate power cord sepa-
rately.
•  Use 100-240 V AC 50/60 Hz to prevent fi re or elec-
tric shock.
•  Do not place any objects on the power cord or do 
not place the projector near heat sources to prevent 
damage to the power cord. If the power cord should 
be damaged, contact your dealer for replacement 
because it may cause fi re or electric shock. 
•  Do not modify or alter the power cord. If the power 
cord is modifi ed or altered, it may cause fi re or elec-
tric shock. 
Caution:
•  Plug in the power cord fi rmly. When unplugging, hold 
and pull the power plug, not the power cord.
•  Do not plug in or out the power cord with your hand 
wet. It may cause electric shock.
Adjustment of the projection angle
For the best projection, project images on a fl at screen 
installed at 90 degrees to the fl oor. If necessary, tilt the 
projector using the two adjustment feet on the bottom 
of the projector. 
Important: 
•  You can correct the vertical and horizontal keystones 
at the same time. However, their adjustment ranges 
are limited in such correction. 
•  When the keystone adjustment is carried out, the 
adjustment value is indicated.  Note that this value 
doesn't mean a projection angle. 
•  The allowable range of the adjustment value in the 
keystone adjustment varies depending on the instal-
lation conditions. 
•  When the keystone adjustment takes effect, the res-
olution decreases. In addition, stripes may appear or 
straight lines may bend in images with complicated 
patterns. They are not due to product malfunctions.  
•  Noise may appear on the screen during the keystone 
adjustment because of the type of the video signal 
being projected and the setting values of the key-
stone adjustment. In such cases, set the keystone 
adjustment values in the range where the image is 
displayed without noise. 
•  When the keystone adjustment is carried out, the im-
age may not be displayed correctly because of the 
type of input signal.
•  When the 1080i signal is input, the keystone adjust-
ment ranges are limited.
Screen
Adjustment feet (Rear)Press  the 

button.Press the 
 
button.
Press  the 

(or -) button.Press the 

 
(or +) button. 
						

							EN - 14
Basic operation
•  Images may not be projected with good quality in 
an extremely hot or cold environment. (This is not a 
product malfunction.) 
4.  Adjust the focus by turning the focus ring.
5.  Choose your desired external input source using  the 
COMPUTER or VIDEO button.
•  The input source is switched between COMPUT-
ER 2 and DVI at every press of the COMPUTER 
2 button on the remote control. (For XD480U / 
XD450U only)
•  The input source is switched between COM-
PUTER 1, COMPUTER 2 and DVI (For XD480U / 
XD450U only) at every press of the COMPUTER 
button on the control panel.
•  The input source is switched between VIDEO and 
S-VIDEO at every press of the VIDEO button on 
the control panel. 
•  The projector automatically selects the appropri-
ate signal format. The selected signal format is 
displayed on the screen.
•  The COMPUTER and VIDEO buttons don't func-
tion while the menu is being displayed. 
•  When COMPUTER 1 or COMPUTER 2 is chosen 
as the source, 
images supplied from the compu-
ter may fl icker. Press the  or  button on the 
remote control to reduce fl icker, if it occurs.
•  To avoid permanently imprinting a fi xed image 
onto your projector, please do not display the 
same stationary images for long 
period.
6.   Adjust the image size by turning the zoom ring.
•  If necessary, adjust the focus and zoom again. 
Power-on
1.  Turn on the device connected to the projector fi rst.
2.  Plug the power cord in the wall outlet. 
•  The POWER indicator lights up. 
•  If the power cord is unplugged from the wall 
outlet before the projector is cooled down com-
pletely after use, the fans may start rotating when 
the power cord is plugged in next time and the 
POWER button may not function. In this case, 
wait for the fans to stop and press the POWER 
button to light the indicator. 
3.  Press the POWER button.
•  It may take about one minute for the lamp to light 
up. 
•  The lamp occasionally fails to light up. Wait a few 
minutes and try to light the lamp again. 
•  After the POWER button is pressed, the image 
may fl icker before the lamp becomes stable. This 
is not a product malfunction. 
•  LAMP MODE can't switch for one minute after 
the power ON. (For XD480U / XD450U only)
55
5 3, 
1, 2P O W E R S TAT U S
3, 1, 2
4
6COMPUTER
VIDEO
KEYSTONE
EXPAND
VOLUME
LASER P in P AUTO POSITION
MENUR-CLICKENTER
MUTESTILL16 : 9
SELECTDVD VIDEO
12
12
MEMORY
ConditionIndicator
STATUS
POWER
-
Stand-by
Red
When the lamp is on.
Green
Green
Important:
•  Do not cover the lens with the lens cap while the 
lamp is on. Do not strip off the aluminum sheet in-
side the lens cap.
•  The projector starts warming up when the POWER 
button is pressed. During the warm-up process, 
images may appear dark and no commands are ac-
cepted.
•  By blinking red, the STATUS indicator indicates that 
the lamp should be replaced soon. Replace the lamp 
when the STATUS indicator blinks red. (See page 27 
and 30.)  
						

							 EN - 15
ENGLISHVOLUME     10
Volume from the speaker
Press the VOLUME + or - button to change the volume 
from the speaker.
The volume control bar will appear on the screen.
•  The volume control bar will disappear about 10 sec-
onds after the VOLUME button is released.
•  The VOLUME buttons dont function while the menu 
selection bar or the menu is being displayed. 
•  When a high-level audio signal, such as a DVD audio 
signal, is supplied to the AUDIO IN terminal, the out-
put from the speaker may be distorted.
AV mute
The video and audio signals are temporarily muted 
when the MUTE button is pressed. To cancel muting, 
press the MUTE button again.
•  If MUTE MODE in the INSTALLATION menu is set 
to IMAGE, the splash screen will appear when the 
MUTE button is pressed. 
•  You can alter the splash screen optionally. See page 
22.
ANAMORPHIC mode
When playing DVD discs containing data of letterboxed 
image, press the 16:9 button. Exit the ANAMORPHIC 
mode, by pressing the 16:9 button again.
Important: 
•  When a letterboxed image is kept displayd for a long 
time before displaying 4:3 image, the afterimages of 
the black bars may appear on the 4:3 image screen. 
Consult your dealer in this case.
Caution: 
•  After using the projector, wait one minute for the air 
outlet fans to stop. Then unplug the power cord from 
the wall outlet.
•  The lamp cant be lit again for one minute after 
turned off for safety purpose. It will take another one 
minute for the STATUS indicator to go out. If you 
want to turn on the projector again, wait until the in-
dicator goes out, and then press the POWER button.
•  The air outlet fans rotate faster as the temperature 
around the projector rises.
•  When the temperature around the projector rises  
high, the sign TEMPERATURE!! blinks red on the 
screen. If the temperature stays high, the lamp will 
go out automatically.
Important: 
•  Do not display a still picture for a long time because 
the afterimages may persist on the screen.
Power-off
Use the following procedure to turn off the projector. Do 
not turn off the projector by unplugging the power cord 
while the lamp is on. Unplugging while the lamp is on 
degrades the lamps performance and causes failure in 
the projector. 
11.  Press the POWER button.
• The message POWER OFF? YES : PRESS 
AGAIN appears on the screen.
•  To cancel, press any button except the POWER 
button. (Some buttons on the remote control 
dont function for cancel.)
22.  Press the POWER button within 10 seconds again.
•  The lamp will go out and the STATUS indicator 
will start blinking. 
•  Though the lamp goes out at this second press 
of the POWER button, the air outlet fans continue 
operating for one minute to cool down the lamp. 
The STATUS indicator will stop blinking. 
33.  Unplug the power cord.
•  The POWER indicator will go out. 
•  If the power cord should be unplugged acciden-
tally while either the air inlet fan or the air outlet 
fans are operating or the lamp is on, allow the 
projector to cool down for 10 minutes with the 
power off. To light the lamp again, press the 
POWER button. If the lamp doesnt light up im-
mediately, repeat pressing the POWER button 
two or three times. If it should still fail to light up, 
replace the lamp. 
Important: 
•  When storing the projector in the provided carrying 
case, the lens should face up.
AUTO POSITION button
When the image isnt projected in the right position with 
COMPUTER selected as the input source, follow the 
procedure below. 
1.  Project a bright image such as the  Recycle Bin 
window on the full screen.
2.  If the screen saver is running, turn it off. 
3.  Press the AUTO POSITION button.
•  If the image is still not in the right position, adjust 
the image position using the SIGNAL menu. See 
page 20. 
						

							EN - 16
Menu operation
IMAGE
XGA60opt.
INSTALLATION
opt.XGA60
INSTALLATION
opt.
AUTO POWER 
ON
AUTO POWER 
OFF
OFF OFF
XGA60
AUTO POWER 
ON
AUTO POWER 
OFF
OFF OFF
AUTO POWER 
ON
AUTO POWER 
OFF
30 minOFF
Basic operation
Several settings can be adjusted using the menu. 
Example : Auto power off time setting 
1.  Press the MENU button.
2.  Press the  or  button to select INSTALLATION.
3.  Press the ENTER button (or  button).4.  Press the 
 or  button to select AUTO POWER 
OFF. 
5.  Press the  or  button to adjust the auto power 
off time.   
6.  Exit the menu by pressing the MENU button sev-
eral times.
Important:
•  When the button doesn't function,  unplug the 
power cord from the wall outlet. Wait about 10 
minutes, plug the power cord in, and try again.  
•  After selecting the items marked with 
, press 
the ENTER button.
IMAGE CONTRAST ±30BRIGHTNESS
COLOR MATRIX±30
sRGB ON, OFFCineRichColor AUTO, 0 - 10
STANDARDLOWHIGHUSER     COLOR TEMP.COLOR  ±10TINT  ±10SHARPNESS  ±5GAMMA MODE AUTO, DYNAMIC, STANDARD, THEATERCONTRAST R  ±30
CONTRAST B  ±30BRIGHTNESS R  ±30BRIGHTNESS B  ±30
EXPAND MODEEXPAND, REAL
INSTALLATION
OFF, MIRROR, INVERT, MIRROR INVERT
AUTO POWER ON
ON , OFF
RESET ALL OK  AUTO POWER OFF
ON , OFF
FEATURE MENU POSITION 1 (Upper left), 2(Lower right)IMAGE REVERSE SPLASH SCREEN
BLACK, IMAGE MUTE MODEBLUE, BLACK, IMAGE BACK COLOR
STANDARD, LOW LAMP MODE
OFF, CENTER, UPPER, LOWER   ANAMORPHICDISPLAY INPUT    , MENU ACCESS    , SPLASH ID SCREENPASSWORD FUNCTION
ON , OFF SCART INPUTVIDEO SIGNAL AUTO , NTSC , PAL , SECAM , 4.43NTSC , PAL-M , PAL-N , PAL-60
LANGUAGE
, English, Español, Deutsch, Français, Italiano,        ,          ,             ,    
VIDEOYELLOW ±30RED ±30BLUE ±30CYAN ±30GREEN ±30
MAGENTA ±30RGB-TINT  ±20
COMPUTER USEROFF
SIGNALHORIZ.POSITION
HOLD0 - 999VERT.POSITION 0 - 999FINE SYNC. 0 - 31
TRACKING
USER0 - 9999
CLAMP POSITION0 - 63CLAMP WIDTH 1 - 63
SHUTTER (L)
0 - 20
SHUTTER (U)
0 - 20
SHUTTER (RS)
0 - 20SHUTTER (LS)
0 - 20
VERT. SYNC.
AUTO, OFF *5
*3 *8
*3 *8
*3 *8
*3 *8*7
AUTO , OFF CINEMA MODE
*3
*3 *5
*5
ON
BEGIN 0 - 15END 0 - 15 OFF
COMPUTER INPUTRGB, YCBCR / YPBPR
*5
*5
OFF,  5,  10,  15,  30,  60 min
OK 
ON
UNLOCKOK LOCK
*1
*1 *1
*1
*2
*1
*1
*3
*6
*4 *2
*2
IMAGE CAPTURESETUPx1, x2, FULLGLAY, RED, GREEN, BLUE, BLACK, WHITE, RED 50%, GREEN 50%, BLUE 50%
CAPTURE BACK COLOR
SIZEGO
(Displayed only when the source is VIDEO or S-VIDEO.)
(Displayed only when the source is VIDEO or S-VIDEO.)
* 1: Not available when sRGB is set to ON.
* 2: Not available with certain signals.
* 3: Not available when the source is a VIDEO 
      or S-VIDEO signal.
* 4: Available only when the input signal is TV60, 480i.
* 5: Setting range differs depending on the input signals.
* 6: For XD480U / XD450U only.
* 7: Available only when the input signal is from the COMPUTER/
COMPONENT VIDEO IN-1.
* 8: Not available when the source is a DVI.
(These items are not available when the 
input source is COMPUTER.) 
						

							EN - 17
ENGLISH
INSTALLATION
opt.
ON
BACK COLOR AUTO POWER 
ON
AUTO POWER 
OFF
SPLASH 
SCREEN
MUTE MODE
LAMP MODEON
BLUE
BLACKOFF
IMAGE
CAPTURESETUPOFF
STANDARD
OFF IMAGE 
REVERSE
XGA60
CONTRAST
IMAGE
0
BRIGHTNESS 0
STANDARD
0
COLOR
AUTO0
XGA60
CineRichColor AUTO
COMPUTEROFF
TINT
0SHARPNESS
COLOR TEMP.
GAMMA MODE COLOR MATRIX sRGB
opt.
1 IMAGE
CONTRAST .......... Use to adjust the image contrast. The contrast becomes 
higher as the value increases.
BRIGHTNESS ....... Use to adjust the image brightness. The image becomes 
brighter as the value increases.
CineRichColor ...... Use to adjust the white level of the projected image. Select 
AUTO for normal use.
sRGB .................... Choose ON for projection emphasizing on the color 
reproducibility.
• When sRGB is ON, CineRichColor, COLOR MATRIX, 
COLOR TEMP., COLOR, TINT and GAMMA MODE can't 
be adjusted.
COLOR MATRIX ... Use to adjust the color balance in each color of the image. 
See page 19.
COLOR TEMP. ...... Use to adjust the color temperature. See page 19.
COLOR ................. Use to adjust the color intensity of the image.
TINT ...................... Use to adjust the color balance of the image. The color balance shifts to green as the value 
increases and shifts to purple as the value decreases. (Available only when VIDEO or S-VIDEO 
is chosen as the source.)
• When the TV50 (PAL, SECAM) signal is input, TINT can't be adjusted.
SHARPNESS ........ Use to adjust the image sharpness. The image becomes sharp as the value increases. (Available 
only when VIDEO or S-VIDEO is chosen as the source.)
GAMMA MODE .... When AUTO is selected, the appropriate gamma mode is automatically selected depending on 
the input signal. For normal use, select  AUTO. Select DYNAMIC for computer sources. Select 
STANDARD for sport scenes and video sources. Select THEATER for fi lm sources. 
2 INSTALLATION
AUTO POWER ON ..... When ON is chosen, the lamp is automatically lit when the 
power cord is plugged in the wall outlet. Choose ON when 
using the projector mounted on the ceiling. 
•  The projector is in the stand-by mode when the lamp is 
off.  Use the remote control to turn on the lamp. 
AUTO POWER OFF .... Use to set the time elapsed before the projector enters 
the stand-by mode when there is no signal input from the 
source. 
IMAGE CAPTURE  Use to capture the screen for the splash screen. See page 
22.
SPLASH SCREEN  Choose ON to display the splash screen when the power is 
turned on. 
•  The splash screen can be changed. See page 22.
BACK COLOR ...... Use to select the background from among BLUE, BLACK and IMAGE, which will be displayed 
when there is no signal input from the source. When IMAGE is selected, the splash screen will 
be displayed. 
MUTE MODE ........ Use to choose the background, either BLACK, or IMAGE, which will be displayed when the 
MUTE button is pressed. When IMAGE is chosen, the splash screen will be displayed. 
LAMP MODE ........ Use to change the brightness of the lamp. When LOW is chosen, the lamp brightness is kept 
low and the projector operating noise is reduced, resulting in a longer lamp replacement interval. 
(For XD480U / XD450U only)
•  When the lamp mode is switched, the projected image may fl icker. This is not a product mal-
function.  
•  Do not change the setting of LAMP MODE frequently. 
IMAGE REVERSE .... Use to reverse the projected image. Select MIRROR for rear projection with the tabletop-
mounted projector. Select MIRROR INVERT for front projection with the ceiling-mounted 
projector.  
•  You can't set IMAGE CAPTURE or SPLASH SCREEN when PASSWORD FUNCTION in the FEATURE menu has 
been set to SPLASH ID SCREEN to enable the password lock. 
						

							EN - 18
3 FEATURE
MENU POSITION .... Use to select the position of the menu on the screen,  1.  
(upper left) or 2. 
 (lower right).
EXPAND MODE .... Choose the mode for enlarging the image. See page 21.
CINEMA MODE .... When AUTO is selected, the fi lm mode will be automatically 
activated when a fi lm source signal is inputted. When OFF is 
selected, the fi lm mode will not be activated. 
VIDEO SIGNAL ..... When AUTO is selected, the appropriate video format is 
automatically selected depending on the input signal. If 
the image isnt displayed correctly, select the desired video 
format manually.
SCART INPUT ...... Choose ON when connecting the projector with a device 
equipped with the SCART terminal that can output RGB 
signal. SCART terminal is used mainly in Europe. Choose 
OFF normally. (Available only for the input signal from the COMPUTER?COMPONENT VIDEO 
IN-1 terminal.)
ANAMORPHIC ..... Select the desired position from among UPPER, CENTER, and LOWER when playing DVD discs 
containing data of letterboxed images. 
PASSWORD FUNCTION .. Use to change the mode of the password lock or to enable or cancel the password lock. See 
page 25 for details. 
LANGUAGE .......... Use to select the language used in the menu. (
 / English / Español / Deutsch / Français / 
Italiano / 
/  /  / PORTUGUÊS).
RESET ALL ........... Use to reset the menu settings (except IMAGE CAPTURE, PASSWORD, and LANGUAGE ). 
•  CINEMA MODE can be adjusted only when a TV60,480i signal is being displayed.
•  SCART INPUT is available only when the input signal is from COMPUTER / COMPONENT VIDEO IN 1 terminal.
•  When SCART INPUT is set to ON, nothing is output to the external monitor.
•  When SCART INPUT is set to ON, normal computer signals arent projected. 
•  Use a SCART-BNC (or SCART-Mini D-SUB 15P) cable (option) when connecting this projector with an AV device 
equipped with the SCART terminal.
•  Some AV devices equipped with the SCART terminal arent compatible with this projector.
•  When VIDEO SIGNAL is set to AUTO, the image may not be projected with correct colors. Change the setting of 
VIDEO SIGNAL depending on the input signal in such cases.
•  When ANAMORPHIC is set to except OFF, the keystone adjustment ranges are limited.
4 SIGNAL
HORIZ. POSITION .... Use to adjust the horizontal position of the image. 
VERT. POSITION ..... Use to adjust the vertical position of the image. 
FINE SYNC. .......... Use to synchronize the projector with the PC input signal so 
that the image is not blurred.
TRACKING ........... Use to eliminate image noise such as wide stripes.
COMPUTER INPUT .....The projector adjusts its settings automatically when 
connected to a DVD player equipped with a component 
video output (Y, C
B, CR). When the projector is connected 
with a device having an RGB terminal, choose RGB 
manually.
HOLD .................... Use to adjust the image when fl agging occurs near the top 
of the screen.
5 SIGNAL - USER (No need to adjust in normal use.)
CLAMP POSITION/
CLAMP WIDTH ..... Use to correct solid white or solid black in the projected image. 
VERT.SYNC. ......... Use to adjust the image when its motion doesnt run smoothly.  
Select AUTO for normal use.
SHUTTER (U) ........ Use to adjust the image when noise appears on the top part of 
the image.
SHUTTER (L) ........ Use to adjust the image when noise appears on the bottom part 
of the image.
SHUTTER (LS) ...... Use to adjust the image when noise appears on the left half of the image.
SHUTTER (RS) ..... Use to adjust the image when noise appears on the right half of the image.
•  If any setting of the SIGNAL-USER menu is changed, the image maynot be displayed cor-
rectly. In this case, press the AUTO POSITION button.
Important:
•  You can set the IMAGE, SIGNAL, and SIGNAL-USER menus only when the signal is supplied. 
FEATURE
OFF
OFF
XGA60
AUTO EXPAND
opt.
MENU POSITION
EXPAND MODEAA
VIDEO SIGNAL?
ANAMORPHIC
RESET ALL
English
LANGUAGEAË
OK
SCART INPUT
DISPLAY
INPUT PASSWORD
FUNCTION
CINEMA MODEAUTO
1.
CLAMP 
POSITIONSIGNAL-USER
0
CLAMP WIDTH 1
SHUTTER (U) 0
SHUTTER (L) 0
SHUTTER (LS) 0
SHUTTER (RS) 0
VERT. SYNC. AUTO?
R G BR G B
SIGNAL
HORIZ. POSITION 0
VERT. POSITION 0
TRACKING 0
COMPUTER 
INPUTRGB
FINE SYNC. 0
USER
XGA60opt.
OK
ONHOLD
Menu operation (continued) 
						

							EN - 19
ENGLISH
Image adjustment
CONTRAST R
COLOR TEMP.-USER
0
CONTRAST B 0
BRIGHTNESS R 0
BRIGHTNESS B 0
CONTRAST
IMAGE
0
BRIGHTNESS 0
STANDARD
0
COLOR
AUTO0
XGA60
CineRichColor AUTO
COMPUTEROFF
TINT
0SHARPNESS
COLOR TEMP.
GAMMA MODE COLOR MATRIX sRGB
opt.
4.  Press the 
 or  button to select the desired color.
•  If you want to adjust the all color balance of the 
image, select RGB-TINT.
5.  Press the  or  button to adjust the color balance 
of the selected color.
6.  Repeat steps 4 and 5 for optimum adjustment re-
sults.
7.  Exit the menu by pressing the MENU button several 
times.
•  When the input source is VIDEO or COMPUTER, the 
setting items in the color matrix adjustment are au-
tomatically set to the predetermined values. You can 
change these settings manually. 
•  To cancel the color matrix adjustment, select OFF in 
step 2. 
•  When the color matrix adjustment is carried out, the 
colors in the menu will also vary. This isnt a product 
malfunction. 
Color temperature
1.  Select COLOR TEMP. in the IMAGE menu. 
2.  Press the  or  button to select USER 
. 
3.  Press the ENTER button.
4.  Press the 
 or  button to select the desired item. 
5.  Press the  or  button to adjust the selected item. 
6.  Repeat steps 4 and 5 for optimum adjustment re-
sults.
7.  Exit the menu by pressing the MENU button several 
times.
COLOR MATRIX
0
0
0
0
0
0
0RED
RGB-TINT
GREEN
BLUE
YELLOW
CYAN
MAGENTA
About color temperature
There are different kinds of white color. Color tem-
perature is a way to show the differences in white. 
White of which temperature is low appears reddish. 
When the color temperature rises, white appears blu-
ish. This projector adjusts this color temperature by 
changing the values of contrast blue and red.
To rise the color temperature:
Increase the CONTRAST B (blue) and decrease the 
CONTRAST R (red).
To reduce the color temperature:
Decrease the CONTRAST B (blue) and increase the 
CONTRAST R (red).
Image adjustment
You can adjust the image using the IMAGE menu. 
To control the white-to-black level of the image :
Adjust CONTRAST in the IMAGE menu.  Press the  
button to increase the contrast and the  button to 
reduce it.
To control the light level of the image :
Adjust BRIGHTNESS in the IMAGE menu.  Press the  
button to lighten the image and the  button to darken 
it.
To determine the intensity of the color :
Adjust COLOR in the IMAGE menu.  Press the 
 but-
ton to increase the amount of color in the image and 
the 
 button to decrease it.
To adjust the red-green color balance of the image :
Adjust TINT in the IMAGE menu.  Press the  button to 
increase the amount of green in the image and the  
button to increase the amount of red in the image.
To adjust the detail and clarity of the image :
Adjust SHARPNESS in the IMAGE menu.  Press the  
button to sharpen the image and the  button to soften 
the image.
Color matrix
This projector adjusts the color balance in each color of 
RGB (red, green, and blue), and their neutral colors (yel-
low, cyan, and magenta) by the color correction adjust-
ment. Use the color correct adjustment when you want 
to emphasize color or when only a certain color balance 
is not correctly adjusted.
1.  Select COLOR MATRIX in the IMAGE menu. 
2.  Press the  or  button to select USER 
.
3.  Press the ENTER button. 
						

							EN - 20
Adjustment of the image from the computer
This projector adjusts the format of the video signal 
supplied from the computer. However, sometimes im-
ages are not projected correctly owing to the type of 
the computer used. When the image from the computer 
isnt projected correctly, press the AUTO POSITION 
button. (See page 15.) If the image isnt projected cor-
rectly yet, adjust the image from the computer using the 
menu.  
To move the image horizontally :
Adjust HORIZ. POSITION in the SIGNAL menu.  Press 
the  button to move the image to the left.  Press the  
button to move the image to the right.
To move the image vertically : 
Adjust VERT. POSITION in the SIGNAL menu.  Press 
the  button to move the image upward.  Press the  
button to move the image downward.
When the image  ickers or the image is out of focus :
Adjust FINE SYNC. in the SIGNAL menu.
When the top part of the image  ags :
Change the setting of HOLD in the SIGNAL menu. Se-
lect ON 
, press the ENTER button, and adjust BEGIN 
or END to minimize the fl agging.
When wide strips appear : 
Adjust CLAMP POSITION or CLAMP WIDTH in the SIG-
NAL - USER menu.
When the motion doesnt run smoothly : 
Adjust VERT. SYNC. in the SIGNAL - USER menu.  Se-
lect AUTO for normal use. 
When noise appears on the right or left half of the 
image :
Adjust SHUTTER (LS) or SHUTTER (RS) in the SIGNAL 
- USER menu.
When noise appears on the top or bottom part of the 
image : 
Adjust SHUTTER (U) or SHUTTER (L) in the SIGNAL - 
USER menu.
R G BR G B
SIGNAL
HORIZ. POSITION 0
VERT. POSITION 0
TRACKING 0
COMPUTER 
INPUTRGB
FINE SYNC. 0
USER
XGA60opt.
OK
ONHOLD
CLAMP 
POSITIONSIGNAL-USER
0
CLAMP WIDTH 1
SHUTTER (U) 0
SHUTTER (L) 0
SHUTTER (LS) 0
SHUTTER (RS) 0
VERT. SYNC. AUTO?
Important:
Do not change any of the settings in the SIGNAL-USER 
menu for normal use.
Simple adjustment method
1.  Select HORIZ. POSITION in the SIGNAL menu.
2. Press the  or  button to adjust the horizontal start 
position (or the left side of the image).
3.  Select TRACKING in the SIGNAL menu.
4. Press the  or  button to adjust the horizontal end 
position (or the right edge of the image).
5.  Repeat steps 1 to 4 for optimum adjustment results. 
6.  Select VERT. POSITION in the SIGNAL menu.
7. Press the  or  button to adjust the vertical start 
position (or the upper edge of the image).
Image adjustment (continued)