Mitsubishi Xd470u Data Projector User Manual

EN-11
ENGLISH
Projector + Computer 
For computer with Mini D-SUB  
For analog connection: 
1. Connect one end of the supplied RGB cable to the COMPUTER IN terminal (1, 2) of the projector.
2. Connect the other end of the RGB cable to the monitor port of the computer. 
For monitor connection:Connect the RGB cable from the monitor to the MONITOR OUT terminal of the projector.
Important:  When you use a longer RGB cable instead of the provided cable, the image may not be projected correctly. 
 Some...

EN-12
Preparation
Preparation for projection 1. Attach the provided power cord to the projector. 
2. Plug the power cord in the wall outlet. 
3. Remove the lens cap. 
Warning:  Do not look into the lens directly when the projector is on. 
 The lens cap is for protecting the lens. If you leave the lens cap on 
the lens with the projector turned on, it may be deformed because 
of heat build-up. Remove the lens cap when you turn on the pro-
jector. 
 One of power cords for the U.S., Europe and U.K. is...

EN-13
ENGLISH
Basic operation
Power-on 1. Turn on the device connected to the projector first. 
2. Plug the power cord in the wall outlet. 
 The POWER indicator lights up. 
 If the power cord is unplugged from the wall outlet before the 
projector is cooled down completely after use, the fans may 
start rotating when the power cord is plugged in next time 
and the POWER button may not function. In this case, wait 
for the fans to stop and press the POWER button to light the 
indicator. 
3. Press the...

EN-14
Basic operation (continued)
Power-off Use the following procedure to turn off the projector.1.Press the POWER button on the control panel or the OFF button 
on the remote control. 
 The message POWER OFF? YES : PRESS AGAIN 
appears on the screen.
 To cancel, press any button except the POWER button. 
(Some buttons on the remote control don’t function for can-
cel.) 
2.Press the POWER button on the control panel or the OFF button 
on the remote control within 10 seconds again. 
 The lamp will go...

EN-15
ENGLISH
Menu operation
Basic operationSeveral settings can be adjusted using the menu. OFF.
Example : Auto power off time setting
1. Press the MENU button.
2. Press the W or X button to select INSTALLATION. 
3. Press the ENTER button (or T button).4. Press the S or T button to select AUTO POWER OFF.
5. Press the W or X button to adjust the auto power off time.
6. Exit the menu by pressing the MENU button several times.
Important:  When the button doesn’t function, unplug the power cord from the...

EN-16
Menu operation (continued)
1IMAGECONTRAST ................................................Use to adjust the image contrast. The contrast becomes 
higher as the value increases.
BRIGHTNESS.............................................Use to adjust the image brightness. The image becomes 
brighter as the value increases.
WHITE ENHANCE ......................................Use to adjust the white level of the projected image. 
Select AUTO for normal use.
COLOR TEMP....

EN-17
ENGLISH
3 FEATUREMENU POSITION ...................................... Use to select the position of the menu on the screen, 1. 
 (upper left) or 2.   (lower right). 
CINEMA MODE ......................................... When AUTO is selected, the film mode will be automati-
cally activated when a film source signal is inputted. 
When OFF is selected, the film mode will not be acti-
vated.
VIDEO SIGNAL .......................................... When AUTO is selected, the appropriate video format is...

EN-18
Image adjustment
Image adjustmentYou can adjust the image using the IMAGE menu. 
To control the white-to-black level of the image : Adjust CONTRAST in the IMAGE menu. Press the X button to 
increase the contrast and the W button to reduce it. 
To control the light level of the image : Adjust BRIGHTNESS in the IMAGE menu. Press the X button to 
lighten the image and the W button to darken it. 
To determine the intensity of the color : Adjust COLOR in the IMAGE menu. Press the X button to increase...

EN-19
ENGLISH
Adjustment of the image from the computer This projector adjusts the format of the video signal supplied from the 
computer. However, sometimes images are not projected correctly 
owing to the type of the computer used. When the image from the 
computer isn’t projected correctly, press the AUTO POSITION but-
ton. (See page 14.) If the image isn’t projected correctly yet, adjust 
the image from the computer using the menu.  
To move the image horizontally : Adjust HORIZ. POSITION in the...

EN-20
Advanced feature
Still To stop the motion in the image temporarily (or to display a still 
image):
Press the STILL button on the remote control.
 The image will freeze temporarily. 
To resume the motion in the image: Press the STILL button on the remote control again. 
Important:  Do not display a still picture for a long time because the afterim-
ages may persist on the screen. 
Page-up and page-down You can control the computer to page-up and page-down the presen-
tation data using the remote...