Mitsubishi Xd450u Data Projector User Manual

EN - 21
ENGLISH
Advanced features
Expand
By pressing the EXPAND button on the remote control, 
you can magnify the image to view the details. You can 
view the image in its original size in the REAL mode.
•  The EXPAND mode doesn't work with video or 
S-video signal. 
•  The EXPAND mode doesn't function with some  in-
put signals. For details, see page 33.
Picture in Picture (PinP) 
One of the special features of this projector is the 
picture-in-picture (PinP) mode. The PinP mode allows 
you to...

EN - 22
Advanced features (Continued)
XD450U XD450UCAPTURE : ENTER X2
CANCEL : MENUCAPTURE : ENTER + ENTER
CANCEL : MENU
XD450U XD450UCAPTURE : ENTER X2
CANCEL : MENU
Setting of the image displayed during startup 
or muting
You can display your desired image as the startup 
screen (or splash screen). Using the menu, you can also 
use such image as a background that is displayed while 
the video is muted or no signal is supplied.
Important:
•  You can't set IMAGE CAPTURE when PASSWORD 
FUNCTION in the...

EN - 23
ENGLISH
Installation other devices remote commands
You can install other device's remote commands in the 
remote control of this projector.
How to install
1.  Set the SELECT switch of the remote control of this 
projector to DVD or VIDEO, depending on the device 
you use.
2.  Place the remote control of this projector and that of 
the other device with their transmission windows 2-5 
cm apart.
3.  Press the MEMORY button.
• 
The MEMORY button will blink red.
• To cancel the installation,...

EN - 24
Advanced features (Continued)
Mouse remote control
By connecting to personal computer through the USB port, you can operate your computer with the projector remote 
control. 
Projector + computer with USB connector
Operation
•  You can use the mouse remote control function with a computer supporting USB only. 
•  When the lamp is turned ON, the computer connected with the USB cable may not work correctly. In this case, 
restart the projector and the computer. If possible, you should disconnect...

EN - 25
ENGLISH
FEATUREPASSWORD FUNCTION
XGA60opt.
LOCK
UNLOCKOK
OK
PASSWORD
CONFIRM
O K CANCEL
FEATUREPASSWORD FUNCTION
XGA60opt.
LOCK
UNLOCKOK
OK
PASSWORD
O K CANCEL
Password function
This projector is equipped with the password function 
that is designed for prevention of theft and wrong op-
eration by children and restriction on operation by other 
than specifi ed users. The password function has three 
modes as follows. 
DISPLAY INPUT ...........When the projector is turned 
on, the startup screen...

EN - 26
Lamp replacement
9.  Tighten up the screw (a) using a 
Phillips screwdriver (+) to secure 
the lamp cover.
Reset of the lamp operation time
Plug in the power cord, turn on the 
lamp, and reset the lamp operation 
time by keep pressing the , ,  and POWER buttons 
on the control panel at the same time about three sec-
onds.
Important:
•  Unless these three buttons are pressed at the same 
time, the lamp operation time isnt reset. 
•  Make sure that the STATUS indicator is lit twice and 
the lamp...

EN - 27
ENGLISH
Troubleshooting
The following offers solutions to some of the common problems you may encounter. We suggest that you consult this 
chart before contacting your dealer.
Images arent projected on the screen.
Problem
Power isn't turned on.
Images aren't projected on 
the screen.
Images suddenly disap-
pear. 
"NO SIGNAL" is displayed.
The screen for entering the 
password appears.
Cause and solution
• Check the states of the indicators.
POWER
Off
Steady red
Blinking red 
/...

EN - 28
Troubleshooting (continued)
Images arent projected correctly.
Problem
Projected images are 
shaking.
Projected images are dis-
placed. 
Projected images are dis-
torted.
Projected images are dark. 
Projected images are 
blurred. 
White dots are seen on 
projected images.
Black dots are seen on 
projected images.
Rainbow blur appears in 
projected images. 
Fine streak pattern ap-
pears in projected images.
Projected images (and/or 
audio) appear wavy and 
distorted. 
Tint in projected images is...

EN - 29
ENGLISH
Others
Cause and solution
• This air comes out as a result of cooling the inside of the projector. This isn't a product malfunc-
tion. 
• Check that the volume isn't set to low. 
• The microcomputers inside the projector may be wrongly operating because of noise. 
 Press the POWER button to turn off the lamp and unplug the power cord from the wall outlet. Wait 
about 10 minutes, plug the power cord in, and try again.
• This indication appears when the ambient temperature rises...

EN - 30
Indicators
POWER STATUS
POWER
Steady 
red
Steady 
green
Steady 
green
STATUS
Off
Blinking 
green
Steady 
green
CONDITION
Stand-by
Lamp stand-by (about 1 minute)
The power is on. (Normal condition)
NOTE
The POWER button cannot be used to
switch between on and off.
POWER
Steady 
green
or
Steady red
Steady red
Steady 
green
Steady red
Steady red
Blinking 
green/red
Blinking 
green/red
STATUS
Blinking orange
Blinking green
Blinking green/red
Blinking red
Steady red
Off
Steady
or
Blinking
CONDITION...