Mitsubishi Xd250u Data Projector Users Manual

							EN-31
ENGLISH
Advanced features (continued)
To cancel the password function:
1. Display the FEATURE menu.
2. Press the S or T button to select PASSWORD FUNCTION.
3. Press the ENTER button.
 The screen for canceling the password function appears.
4. Press the ENTER button.
 The screen for entering the password appears.
5. Enter a 4 - 8 digit password using the S, T, W or X buttons on 
the remote control as shown below.
(S=1, X=2, T=3, W=4)
6. Press the ENTER button.
 If you enter a wrong password, an error message appears.
 To cancel the procedure, press the MENU button.
Important: When the screen for entering the password is displayed, to disable 
the password function, hold down the SOURCE and POWER but-
tons on the control panel together for about three seconds.
MagnifyBy pressing the MAGNIFY button on the remote control, you can mag-
nify the image to view the details.
 The MAGNIFY mode doesnt function with some input signals. For 
details, see page 41.
 The MAGNIFY mode doesnt work with video or S-video signal.
MAGNIFY
To use the MAGNIFY mode:
1. Press the MAGNIFY button.
 You can select the area to be magnified by pressing the S, 
T, W or X button on the remote control.
 You can change the magnification of the selected area by 
pressing the VOLUME S or T button.
2. Press the MAGNIFY button again to exit the MAGNIFY mode.
 The regular operation screen will appear.
Important: In the MAGNIFY mode, you cant adjust the volume.
FEATUREMENU ACCESSLOCKOK
opt.
UNLOCKOK
PASSWORD
1
32 4
O K : ENTER CANCEL : MENU
Magnified image 
						

							EN-32
Advanced features (continued)
Supervising and controlling by computerYou can supervise and control the projectors operation using a personal computer via a LAN network.
 To supervise and control the projector, install the software ProjectorView Global +* contained in the attached CD-ROM. For the installation pro-
cedure and usage of the software, see User Manual of LAN Control Utility contained in the attached CD-ROM.
*) Functions
 Batch operation of stand-alone projector / multiple projectors
 Scheduling function to turn ON/OFF for each day of the week
 Checking each condition of the projector and detecting a theft
 Setting of the projectors IP CONFIG
 Startup of the controlling / supervising tool (ProjectorView) using the Web browser
 Activating Visual PA to display the specified characters on the projectors screen
Major functionsProjectorView Global + Batch Projector controlling / supervising application software
ProjectorView
The controlling / supervising tool using the Web browser
PJLink™
This projector supports standard protocol PJLink™
 for projector control and you can control and monitor projectors operations using the same appli-
cation among projectors of different models and different manufacturers.
Connection 
 Use a straight-through category-5 cable for LAN connection.
 Dont touch the metal parts of the LAN connector and LAN cable because static electricity may be discharged from your body, causing damage 
to the projector.
Using the User ManualThe User Manual for LAN Control Utility is prepared in the Portable Document Format (PDF) in the CD-ROM.
Opening the User Manual:
1. Load the CD-ROM into the CD-ROM drive.
2. Open CD-ROM XD250U/XD250U-G/XD280U/XD280U-G.
3. Double-click on MANUAL_LAN.HTML within the CD-ROM. A language selection list for the User Manual will be displayed.
4. Move the mouse pointer to the desired language and click.
About PJLinkTM
 To use PJLink™ function, the PJLink™ application software is required.
 For the specifications of PJLink™, access to the Web site of Japan Business Machine and Information System Industries Association 
(JBMIA). (http://pjlink.jbmia.or.jp/english
)
 This projector is fully compliant to the specifications of JBMIA PJLink™ Class 1. It supports all the commands defined by PJLink™ Class 1, 
and the compliance has been verified with the PJLink™ standard specifications Version 1.0.
To LAN terminalLAN cable (option)
(100BASE-TX or 10BASE-T 
should be suppor ted.)Computer
External HUB
LAN cable (option)
(100BASE-TX or 10BASE-T should be supported.)
STANDBY MODE (See page 21.) in INSTALLATION MENU is set to LOW as a factory default. When STANDBY MODE is set to LOW, LAN 
connection is not available. To enable the LAN connection, set the STANDBY MODE to STANDARD. 
						

							EN-33
ENGLISH
Lamp replacement
This projector is equipped with a lamp to project images. This lamp is 
a consumable. It may burn out or its brightness may decrease during 
use. In such cases, replace the lamp with a new one as soon as possi-
ble. Be sure to replace the lamp with a new lamp separately sold that 
is exclusive to this projector. Contact your dealer for purchase of the 
lamp.
Replace the spare lamp using the lamp attachment unit that is 
equipped with the spare lamp (separately sold) designed specifically 
for this projector.
Caution: Do not remove the lamp immediately after using the projector. You 
may get burned because the lamp is very hot after use.
 Before replacing the lamp, press the POWER button to turn off the 
lamp and wait for two minutes for lamp to cool down. Unplug the 
power cord from wall outlet and wait one hour for the lamp to cool 
down completely.
 Do not remove the lamp except for replacement. Careless han-
dling can cause injury or fire.
 Do not touch the lamp directly. It may break and cause injury or 
bur n.
 Be sure not to drop the lamp lid screw into the projector. Also be 
sure not to put metal or any flammable objects inside because it 
may cause fire or electric shock. If any objects should fall inside, 
unplug and contact your dealer.
 Install the lamp securely to prevent failure and fire.
 If the lamp should break, small glass fragments may fall out 
through the grilles and some may remain inside of the projector or 
the lamp box. When taking the lamp box out, be sure to turn over 
the projector and hold the handle of the lamp box to avoid injury 
due to the glass fragments.
 If the lamp should break, never shake the lamp box or hold it in 
front of your face after removing it. The glass fragments may fall 
out and cause injury to your eyes.
 Be sure to use the lamp dedicated to this projector, VLT-XD280LP 
for XD250U/XD250U-G/XD280U/XD280U-G. Use of other lamps 
may cause a failure of the projector.
 Do not use any other tools for replacing the spare lamp, and be 
sure to use the lamp attachment unit that is equipped with the 
spare lamp (separately sold) designed specifically for this projec-
tor. Use of other tools may cause a failure of the projector.
Make sure that the projector is securely held in place.
1. Remove the cover (a) of the screw fixing the lamp cover with a fin-
gernail. If it is difficult to remove it with a fingernail, use a fine-
tipped tool such as flathead screwdriver.
2. Remove the screw (b) and slide the lamp cover (c) for removal.The lamp unit is fixed in position with two retaining claws (d) inside 
so the lamp attachment unit (e) designed specifically for this pro-
jector is required to replace the lamp.
Do not pull out the lamp forcibly. The lamp unit may be irretrievably 
damaged.
A new lamp unit can be installed without the lamp attachment unit.
3. Loosen the two screws (g) indicated as arrows (
J) in figure, and 
mount the lamp attachment unit (e).
Slide the lamp attachment unit in the direction indicated by a white 
arrow after the installation of it, and hook the claw (f) into the hole 
of the device to fix the lamp attachment unit.
If not hooking the claw, the lamp attachment unit will be lifted with-
out being fixed in the precise position.
(Caution)
When replacing the lamp, do not remove the screws other than 
those in the above picture. If do, it might cause the failure of prod-
uct.
When the projector is mounted to the ceiling:
Secure the lamp attachment unit and the projector with the screw 
(h) that come with the lamp attachment unit. Otherwise, the lamp 
unit may fall from the inside and cause injuries.
 Contact your dealer when replacing the lamp unit with the pro-
jector mounted to the ceiling.
4. Pull up the handle (i), and then pull out the lamp unit (j) by the han-
dle. Spare lamp for XD250U/XD250U-G/XD280U/XD280U-G: 
VLT-XD280LP
(a)
(c)
(b)
(d)(f)
(g)
(e)
(h)
(j)
(i) 
						

							EN-34
Lamp replacement (continued)
5. Remove the lamp attachment unit.
 Pull the lamp unit out of the projector slowly. If it is pulled out 
quickly, the lamp may break, scattering glass fragments.
 Do not spill liquid on the removed lamp unit or do not place it 
near any flammable object or where children can reach to pre-
vent injuries or fire.
When the projector is mounted to the ceiling:
Confirm that the lamp unit (j) is securely held inside the lamp dispos-
able bag of the lamp attachment unit. And then loosen the screw (h) 
that come with the lamp attachment unit. Then remove the lamp 
attachment unit.
6. Load a new lamp unit securely into the projector in the right orien-
tation.
7. Secure the lamp cover (c) with screws (b) back again, and mount 
the cover (a).
 Make sure that the lamp cover is secured firmly. Otherwise, the 
POWER indicator flashes red and green, disallowing the projec-
tor to be powered on.
Reset of the lamp operation time
1. Connect with the Power cord, and turn the power on.
2. Display DETAIL MENU. (See page 17.)
3. Select LAMP TIME RESET in INSTALLATION menu, and press 
ENTER button to reset lamp operation time.
Important: The projector doesn’t turn on if the lamp cover isn’t attached 
securely.
 Be sure to reset the lamp operation time whenever you replace the 
lamp.
 Do not reset the lamp operation time unless you replace the lamp.
Caution: The lamp is fragile. If it is broken, be careful not to cut yourself with 
glass fragments.
 Contact your dealer for a new lamp.
Interval of lamp replacementWhen the lamp lifetime notice is issued, the lamp replacement is rec-
ommended even if the lamp is lit normally. Decrease in luminescence 
and/or color brightness indicates that the lamp needs to be replaced. 
When the lamp operation time exceeds the time elapsed until the 
lamp lifetime notice
*1 is issued, the indicator will blink alternately 
green and red while the lamp is lit (while the lamp is not lit, the indica-
tor will blink red only) and the lamp replacement message will appear 
on the screen for one minute every time the lamp is turned on. When 
the lamp operation time exceeds the time elapsed until the lamp life-
time warning
*2 is issued, the replacement message (LAMP 
EXCHANGE) will appear on the screen for one minute at fixed inter-
vals
*4 thereafter.
When the lamp operation time exceeds the time elapsed 
until the lamp lifetime*3, the projector keeps on issuing 
the warning, shuts off automatically after ten minutes, 
and then enters the standby state.
The times above are when LAMP MODE of the INSTALLATION menu 
is set to LOW. When it is set to STANDARD, this duration will be short-
ened.
*4These intervals vary depending on the lamp mode setting.*5When LAMP MODE is set to STANDARD, the time elapsed until 
the lamp lifetime will be shortened to 3000 hours.
Important: Do not open the lamp cover when the projector is set at a ceiling or 
a high place. Lamp fragments may fall from the inside if the lamp 
were broken. 
Please contact your dealer when you need to replace the lamp 
with a new one.
Caution:
 This projector uses a lamp that 
contains mercury. Disposal of the 
lamp or the projector with the lamp 
may be regulated due to environ-
mental considerations. For disposal 
or recycling information, please 
contact your local authorities or the 
Electronic Industries Alliance: 
www.eiae.org. (For US only).
XD250U/XD250U-G/XD280U/XD280U-G*1 3750 Hours*2 4750 Hours*3 6000 Hours*5 
						

							EN-35
ENGLISH
Troubleshooting
Before asking for repair of the projector, check the following. If the symptom persists, stop using the projector, be sure to unplug the power plug, and 
then contact your dealer.
No image appears on the screen.
 
ProblemSolution
Power can not be turned on. Check whether the indicators are on or off and how they are lightning. 
No image appears on the screen. Cancel the AV mute by pressing the AV MUTE button.
 Check that the lens cap is removed.
 It may take about 1 minute for the lamp to light up.
 The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.
 If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotat-
ing and the POWER button may not work after the power cord is plugged. After the fan stops rotating, press 
the POWER button to turn back on the POWER indicator.
 Check that the intake vent is clean.
 Check that the lamp cover is closed. (See page 34.)
 Check that the cables connected to the external devices are not broken.
 When an extension cable is being used, replace it with the supplied cable for check.
 When images are displayed correctly, add an RGB signal amplifier to the extension cable.
Pow e r  t u r n s  o f f. This problem may occur when the intake vent and/or exhaust vents are blocked. (In such a case, the STATUS 
indicator brinks orange.)
JRemove the objects blocking the intake vent and/or exhaust vents and then carry out the following proce-
dure.
1. Wait for the intake fan and/or exhaust fan to stop. (Wait until the STATUS indicator goes out.)
2. Unplug the power cord from the wall outlet.
3. Wait about 10 minutes.
4. Plug the power cord into the wall outlet.
5. Press the POWER button.
 Check that AUTO POWER OFF has been set to OFF.
 If the lamp has deteriorated, it may go out after a while it illuminates.
The screen for entering the password appears. PASSWORD FUNCTION in the FEATURE menu has been set to DISPLAY INPUT to enable the password 
lock.
JEnter the password or contact the person in charge of management of the projector.
(See page 30.)
NO SIGNAL is displayed. Turn on the power of the connected device, or check whether there is something wrong with the connected 
device.
 Check whether the external device output signals. (Check this especially when the external device is a note-
book computer.)
 Check that the cable connected to the external device isn’t defective.
 Check that the projector is connected to the external device using the correct terminals.
 Check that the connected device is correctly selected as the input source.
 When an extension cord is being used, replace it with the supplied cable and check whether images are pro-
jected correctly. If images are projected correctly, use an RGB signal amplifier along with the extension cord.
Off
Blinking red
/ greenSteady
or
Blinking
Blinking
orange
Blinking
green
Steady red
Off
Off
Off
POWER STATUS Solution
 Connect the power cord to the projector. Plug the power cord into a wall outlet. If any objects are blocking the air inlet or outlet grille, remove them and carry out 
the following.
1.  Unplug the power cord from the wall outlet.
2.  Make sure that the projector has cooled off.
3.  Plug the power cord into the wall outlet.
4.  Press the POWER button.
 If any objects are blocking the air inlet or outlet grille, remove them. Dont expose the air outlet grilles to hot air emitted from a heating appliance.
 After the STATUS indicator stops blinking, press the POWER button. If you unplug the power cord while the fan is rotating, the lamp may not turn on about 1 
minute when you plug the power cord next time.
 The lamp cant turn on again for 1 minute after it goes out. Press the POWER button several times. Attach the lamp cover on the top.
 Unplug the power cord from the wall outlet and contact your dealer. 
						

							EN-36
Troubleshooting (continued)
Images are not displayed correctly.
ProblemSolution
Projected images are shaking.
Projected images are displaced. Check that the cable connected to the external device isn’t intermittent.
 Connect the cable’s plug with the external device’s connector firmly.
 Press the AUTO POSITION button.
 Some computers output out-of-spec signals on rare occasion. Adjust the SIGNAL menu. (See page 26.)
 When the input signal is a WXGA video signal, confirm the setting selected in WXGA in the FEATURE menu.
 When the input signal is other than a WXGA video signal, select OFF in WXGA in the FEATURE menu.
Projected images are distorted.  Adjust the projector and the screen so that they are perpendicular to each other. (See page 9.)
Projected images are dark. Adjust BRIGHTNESS and CONTRAST in the QUICK MENU or the IMAGE menu. (See page 25.)
 Replace the lamp. (See page 33.)
Projected images are blurred. Adjust the focus. (See page 14.)
 Clean the lens.
 Press the W or X button on the remote control to eliminate flicker.
 Adjust TRACKING and FINE SYNC. in the SIGNAL menu. (See page 26.)
 Adjust BRIGHTNESS and CONTRAST in the QUICK MENU or the IMAGE menu. (See page 25.)
 Adjust the projector and the screen so that they are perpendicular to each other. (See page 9.)
Afterimages persist on the screen. This phenomenon is improved by keeping projecting an evenly bright image. (Such image burn-in phenom-
enon where afterimages persist on the screen may occur if a stationary image is kept displayed on the screen 
for a long time.)
White dots are seen on projected images. Black dots 
are seen on projected images. This phenomenon is normal for a DLP projector and is not a malfunction. (A very small number of pixels may 
visibly or invisibly be persistent all the time, but they are not a sign of system malfunctions. Over 99.99% of 
the pixels are effective.)
Fine streaks are seen on projected images. This is due to interference with the screen surface and is not a malfunction. Replace the screen or displace 
the focus a little.
 Vertical or horizontal streak noise may appear on the projected image, depending on the type of the DVD 
player, game console or computer you use. In such a case, you can reduce such streak noise by enabling the 
LPF.
Projected images become wavy. Connect the plugs of the cables to external devices securely. 
 Keep the projector away from equipment generating interfering radio waves. 
 When the keystone adjustment is carried out, the image may not be displayed correctly because of the type 
of input signal. This isn’t a product malfunction. In this case, readjust the keystone so that the amount of key-
stone correction is as small as possible. 
Hue is not appropriate.  Check that the cables connected to the external devices are not broken.
Tint in projected images is incorrect. Check that COMPUTER INPUT in the SIGNAL menu is correctly set. (See page 23.)
 Check that the cable connected to the external device isn’t broken.
Different color tint. When comparing images projected by two projectors, tints in the displayed images may be different because 
of variation between their optical components. This is not a malfunction.
 When comparing the image projected by this projector with those displayed on the television or PC monitor, 
tints in the displayed images may be different because of difference in the range of color reproducibility. This 
is not a malfunction.
Only the motion areas in the images supplied from 
the computer aren’t displayed. This is caused by the computer being used. Contact the manufacturer of your computer.
Projected images are obscured. Match the output resolution of your computer with the resolution of the projector. For the method to change 
the output resolution of the computer, contact the manufacturer of your computer. (See page 41.)
 Some images and texts appear obscured during the keystone adjustment. In such cases, use the projector 
without applying the keystone adjustment. (See page 13.)
Projected images are flickering After the Power button or On button on the remote has been pressed, or the Lamp mode setting has 
changed, images may be flickering until the lamp lights stably. This is an expected behavior.
 When selecting the input signal, Auto Position, and Color Enhancer, the projected image may be flickering 
temporarily. This is not a product malfunction.
Projector images are twitching. Projector may be vibrating. Set AUTO KEYSTONE to OFF or lower the VOLUME T button of the Remote 
control. 
						

							EN-37
ENGLISH
Troubleshooting (continued)
Others
If the following problem occurs after the lamp is replaced, check the following first.
Maintenance 
Warning:Do not use flammable solvents (benzene, thinner, etc.) and flammable aerosols when cleaning the projector body and lens. Flammable substances 
may ignite causing fire or breakdown while the lamp is illuminating.
Caution: Be sure to turn off the lamp and unplug the power cord from the wall outlet before you perform any maintenance on the projector. 
Cleaning of the projector and the ventilation slots Use a soft cloth to clean the projector and the ventilation grilles. When the grilles become dirty, wipe them with a soft cloth dampened with diluted 
mild detergent, and then wipe them with a dry cloth. 
To protect the surface of the projector from fading or deteriorating:  Do not spray insecticide on or inside the projector. 
 Do not use benzin or thinner to clean it. 
 Do not let rubber or plastic materials contact with projector. 
Cleaning of the lens Use a standard lens-cleaning brush or a piece of lens tissue dampened with lens cleaning fluid. The lens surface is fragile. Use only recommended, 
nonabrasive lens-cleaning materials. Do not touch the lens with your fingers. 
 
ProblemSolution
The exhaust vents emit warm air.  This air comes out after cooling the inside of the projector. You may feel hot, but this is not a malfunction.
No audio is output. Check that the volume isn’t set to low.
 Check the AUDIO INPUT setting.
 When the external device is connected with an HDMI cable, set the audio output of the device to PCM output.
The menu can’t be used. The microcomputers inside the projector may be wrongly operating because of noise.
JPress the POWER button to turn off the lamp and unplug the power cord from the wall outlet. Wait about 
10 minutes, plug the power cord in, and try again.
TEMPERATURE!! is displayed. This indication appears when the ambient temperature rises high. When the ambient temperature stays high, 
the lamp goes out.
JEliminate any causes of the rise in the ambient temperature.
 This indication appears when the air inlet or outlet grille is blocked. When they are kept blocked, the lamp 
goes out.
JRemove the objects blocking the air inlet or outlet grille.
The   mark appears.  This mark appears when ineffective operation is carried out. This isn’t a product malfunction.
The remote control doesn’t function easily or at all. Check that the batteries are loaded in the remote control or the batteries are not weak. (See page 8.)
 Check that the remote control sensor isn’t exposed to direct sunlight or fluorescent light. (See page 8.)
 Use the remote control within its operation range. (See page 8.)
 Use the remote control at least 10 cm away from the projector.
The SOURCE button on the control panel doesn’t 
function. PASSWORD FUNCTION in the FEATURE menu has been set to MENU ACCESS to enable the password 
lock.
JCancel the password lock or contact the person in charge of management of the projector.
(See page 31.)
Abnormal sound is heard. Because the color wheel spins at a high speed, metallic sounds may be heard in rare occasions. Such symp-
tom is not a malfunction.
ProblemSolution
The projector does not turn on. Fit the lamp cover securely. (See page 34.)
 Reset the lamp operating time. (See page 34.)
The STATUS indicator blinks.  Reset the lamp operating time. (See page 34.) 
						

							EN-38
Indicators
This projector has two indicators, each of which shows the operation condition of the projector. 
The following offer solutions to possible problems. If these problem persist, turn the projector off and consult your dealer.
Normal condition
Abnormal condition
POWERSTATUSCONDITIONNOTE
Stand-by
Lamp stand-by (about 1 minute)The POWER button cannot be used to switch 
between on and off.
The power is on. (Normal condition)
STATUS indicator POWER indicator
Steady redOff
Steady greenBlinking green
Steady green
Steady green
POWERSTATUSCONDITIONPOSSIBLE SOLUTION
Abnormal temperature
 The ventilation grilles is clogged with dust or dirt.
 The room temperature is high. Clean the ventilation grilles.
 Relocate the projector to a cooler place.
The protection circuit is working or the lamp is in an abnormal con-
dition. Wait until the STATUS indicator goes out, then 
press the POWER button.
 If the above solution is not effective, replace the 
lamp.
The lamp operation time exceeds the time elapsed until the lamp 
lifetime notice while the power is on. (See page 34.)
Replace the lamp.
Change with a new lamp if this problem recurs. The lamp operation time exceeds the time elapsed until the lamp 
lifetime notice while the power is off. (See page 34.)
The lamp operation time exceeds the time elapsed until the lamp 
lifetime. (See page 34.)
The lamp cover isn’t closed. Close the cover correctly.
Abnormal. Contact your dealer.
Steady green
or
Steady red
Blinking orange
Steady red
Blinking green
Steady greenBlinking green/red
Steady red
Blinking red
Steady redSteady red
Blinking green/redOff
Blinking green/red
Steady
or
Blinking 
						

							EN-39
ENGLISH
Specifications
 The specifications and outside appearance of the projector are subject to change without prior notice. 
Ty p e D L P ™  D ATA  p r o j e c t o r  
Model XD250U/XD250U-G/XD280U/XD280U-G
Rated power supply 100 - 240 V AC, 50 / 60 Hz 
Power consumption3.3 A
During standby:
AC 100-120V: 3W (when STANDBY MODE is STANDARD)
0.4W (when STANDBY MODE is LOW)
AC 220-240V: 3W (when STANDBY MODE is STANDARD)
0.5W (when STANDBY MODE is LOW)
Display Technology0.55-inch Single chip Digital Micromirror Device (DMD) 
Pixels 1024 x 768 = 786432 pixels 
Colors 16770000 colors
Projection lens F 2.5-2.8, f = 18.4 - 22.0 mm 
Light source lamp 230 W
Picture size 40 - 300 inch (aspect ratio 4:3) 
PC compatibilityResolution:640x400 (Expand) - 1024x768 (Real) - 1280x1024 (Compress)
Sync on Green available
Video compatibilityNTSC / NTSC 4.43 / PAL (including PAL-M, N) / SECAM / PAL-60 
Component Video (DVD/HDTV) (480i, 576i, 480p, 576p, 1080i, 720p)
Speaker 10 W Mono, Round type ø5 cm x 1
S-video inputLuminance signal: 1.0 Vp-p 75 Ω (negative sync.) 
Chroma signal: 0.286 Vp-p 75 Ω (burst signal) 
Video input 1.0 Vp-p 75 Ω (negative sync.) 
Audio input 350 mVrms, 10 kΩ or more 
Analog RGB inputRGB: 0.7 Vp-p 75 Ω (negative sync.) 
YP
BPR/YCBCR : Y:1.0 Vp-p (negative sync.) PBPR/CBCR:0.7 Vp-p 
HD/CS : TTL level (positive or negative) 
VD : TTL level (positive or negative)
HDMI inputHDMI 19-pin
HDMI interface (TMDS single link) (only PCM audio is supported)
Control connector Serial terminal (RS-232C) (Mini DIN) 
Outside dimensions 325 x 118 x 251 mm (width x height x depth)
Weight Approx. 3.3 kg 
Length of power cord 114 inch (1.8 m)
Temperature, humidity
(performance guaranteed)+41
°F (+5°C) - +95°F (+35°C), 30 - 90%  
						

							EN-40
Specifications (continued)
Connectors
Dimensional drawings (unit : mm)
What’s included in the box
Replacement part
15 11
610 15
pin No.Spec.
1R(RED)/CR
2G(GREEN)/Y
3B(BLUE)/CB
4GND
5GND
6GND
7GND
8GND
9 DDC5V
10 GND
11 GND
12 DDC Data
13 HD/CS
14 VD
15 DDC Clockpin No.Spec.
1 R(RED)/CR
2 G(GREEN)/Y
3B(BLUE)/CB
4-
5GND
6GND
7GND
8GND
9-
10 GND
11 -
12 -
13 HD/CS
14 VD
15 -
COMPUTER IN/OUT (Mini D-SUB 15-pin)
IN OUT
191
2
18
HDMI IN (HDMI 19-pin)
pin No.Spec.
1TMDS Data2+
2 TMDS Data2 Shield
3TMDS Data2-
4TMDS Data1+
5 TMDS Data1 Shield
6TMDS Data1-
7TMDS Data0+
8 TMDS Data0 Shield
9TMDS Data0-
10 TMDS Clock+
11 TMDS Clock Shield
12 TMDS Clock-
13 CEC
14 -
15 SCL
16 SDA
17 DDC Ground
18 +5 V Power
19 Hot Plug Detect
AC power cord
1 RGB cable for PCfor US J2552-0063-01
for EU J2552-0066-01
for UK J2552-0065-01
J2552-0072-031 Remote control
1 Safety Manual/Quick Start up
1 CD-ROM
2 Battery
1 Lens cap
1 Soft case
(Option / Not included in the box)
Spare lamp for XD250U/XD250U-G/XD280U/XD280U-G VLT-XD280LP
251
325
118