Mitsubishi Xd210u Data Projector User Manual

							
EN-21
ENGLISH
Troubleshooting
Before asking for repair of the projector, check the following. If the symptom persists, stop using the projector, be sure to u nplug the power plug, and 
then contact your dealer.
No image appears on the screen.
 
ProblemSolution
Power can not be turned on. • Check whether the indicators are on or off and how they are lightning. 
No image appears on the screen. • Cancel the AV mute by pressing the AV MUTE button.
• Check that the lens cap is removed.
• It may take about 1 minute for the lamp to light up.
• The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.
• If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotat-
ing and the ON button may not work after the power cord is plugged. After the fan stops rotating, press the 
ON button to turn back on the POWER indicator.
• Check that the intake vent is clean.
• Check that the lamp cover is closed.(See page 20.)
• Check that the cables connected to the external devices are not broken.
• When an extension cable is being used, replace it with the supplied cable for check.
• When images are displayed correctly, add an RGB signal amplifier to the extension cable.
• When the menu is turned on and the signal is lost or not input, the system will not search for the signal even  if the signal is input again. In this case, turn off the menu. 
Power turns off. • This problem may occur when the intake vent and/or exhaust vents are blocked. (For example:  the STATUS 
indicator brinks red.)
JRemove the objects blocking the intake vent and/or exhaust vents and then carry out the following proce-
dure.
1. Wait for the intake fan and/or exhaust fan to stop. (Wait until the POWER indicator lights green.)
2. Unplug the power cord from the wall outlet.
3. Wait about 10 minutes.
4. Plug the power cord into the wall outlet.
5. Press the ON button.
• When the POWER indicator is steady amber, it is indicating that the lamp should be replaced. Replace the  lamp in this case.
• If the lamp has deteriorated, it may go out after a while it illuminates.
• Check if the Auto power off function is set. 
No Signal is displayed. • Turn on the power of the connected device, or check whether there is something wrong with the connected 
device.
• Check whether the external device output signals. (Check this especially when the external device is a note- book computer.)
• Check that the cable connected to the external device isn’t defective.
• Check that the projector is connected to the external device using the correct terminals.
• Check that the connected device is correctly selected as the input source.
• When an extension cord is being used, replace it with the supplied cable and check whether images are pro- jected correctly. If images are projected correctly, use an RGB signal amplifier along with the extension cord.
Off
Steady greenBlinkingred
Blinking
green
Blinkinggreen
Steady green
Off
Off
Steady amber
Steady green
BlinkinggreenBlinking red
POWER STATUS Solution 
						

							
EN-22
Troubleshooting (continued)
Images are not displayed correctly.
ProblemSolution
Projected images are shaking.
Projected images are displaced. • Check that the cable connected to the external device isn’t intermittent.
• Connect the cable’s plug with the external device’s connector firmly.
• Press the AUTO POSITION button.
• Some computers output out-of-spec signals on rare o
ccasion. Adjust the Computer Image menu. (See page 
17.)
Projected images are distorted. • Adjust the projector and the screen so that they are perpendicular to each other. (See page 9.)
Projected images are dark. • Adjust Brightness and Contrast in the Picture menu. (See page 16.)
• Replace the lamp. (See page 20.)
Projected images are blurred. • Adjust the focus. (See page 13.)
• Clean the lens.
• Adjust Tracking and Fine sync. in the Computer Image menu. (See page 17.)
• Adjust Brightness and Contrast in the Picture menu. (See page 16.)
• Adjust the projector and the screen so that they are perpendicular to each other. (See page 9.)
Afterimages persist on the screen. • This phenomenon is improved by keeping projecting an evenly bright image. (Such image burn-in phenom-
enon where afterimages persist on the screen may occur if a stationary image is kept displayed on the 
screen for a long time.)
White dots are seen on projected images. Black dots 
are seen on projected images. • This phenomenon is normal for a DLP projector and is not a malfunction. (A very small number of pixels may 
visibly or invisibly be persistent all  the time, but they are not a sign of system malfunctions. Over 99.99% of 
the pixels are effective.)
Fine streaks are seen on projected images. • This is due to interference with the screen surface and is not a malfunction. Replace the screen or displace 
the focus a little.
• Vertical or horizontal streak noise may appear on the projected image, it may depend on the type of the DVD  player, game console or computer you use.
Projected images become wavy. • Connect the plugs of the cables to external devices securely. 
• Keep the projector away from equipment generating interfering radio waves. 
• When the keystone adjustment is carried out, the image may not be displayed correctly because of the type 
of input signal. This isn’t a product malfunction. In this case, readjust the keystone so that the amount of key-
stone correction is as small as possible. 
Hue is not appropriate. • Check that the cables connected to the external devices are not broken.
Tint in projected images is incorrect. • Check that Signal Type in the Setting menu is correctly set. (See page 18.)
• Check that the cable connected to the external device isn’t broken.
Different color tint. • When comparing images projected by two projectors, tints in the displayed images may be different because 
of variation between their optical components. This is not a malfunction.
• When comparing the image projected by this projector with those displayed on the television or PC monitor, 
tints in the displayed images may be different because of difference in the range of color reproducibility. This 
is not a malfunction.
Only the motion areas in the images supplied from 
the computer aren’t displayed. • This is caused by the computer being used. Contact the manufacturer of your computer.
Projected images are obscured. • Match the output resolution of your computer with the resolution of the projector. For the method to change 
the output resolution of the computer, contact the manufacturer of your computer. (See page 27.)
• Some images and texts appear obscured during the keystone adjustment. In such cases, use the projector  without applying the keystone adjustment. (See page 12.)
Projected images are flickering • After the ON button on the remote has been pressed, or the Lamp mode setting has
 changed, images may 
be flickering until the lamp lights stably. This is an expected behavior.
• When selecting the input signal, AUTO POSITION  and Image in Menu, the projected image may be flicker-
ing temporarily. This is not a product malfunction. 
						

							
EN-23
ENGLISH
Troubleshooting (continued)
Others
If the following problem occurs after the lamp is replaced, check the following first.
Maintenance 
Warning:Do not use flammable solvents (benzene, thinner, etc.) and fla mmable aerosols when cleaning the projector body and lens. Flamma ble substances 
may ignite causing fire or breakdown while the lamp is illuminating.
Caution: Be sure to turn off the lamp and unplug the power cord from  the wall outlet before you perform any maintenance on the projector . 
Cleaning of the projector and the ventilation slots Use a soft cloth to clean the projector and the ventilation grilles. When the grilles become dirty, wipe them with a soft cloth  dampened with diluted 
mild detergent, and then wipe them with a dry cloth. 
To protect the surface of the projector from fading or deteriorating: • Do not spray insecticide on or inside the projector. 
• Do not use benzin or thinner to clean it. 
• Do not let rubber or plastic materials contact with projector. 
Cleaning of the lens Use a standard lens-cleaning brush or a piec e of lens tissue dampened with lens cleaning fluid. The lens surface is fragile. Use only recommended, 
nonabrasive lens-cleaning materials. Do  not touch the lens with your fingers. 
 
ProblemSolution
The exhaust vents emit warm air. • This air comes out after cooling the inside of the projector. You may feel hot, but this is no t a malfunction.
No audio is output. • Check that the volume isn’t set to low.
The menu can’t be used. • The microcomputers inside the projector may be wrongly operating because of noise.
JPress the ON button to turn off the lamp and unplug the power cord from the wall outlet. Wait about 10 
minutes, plug the power cord in, and try again.
The remote control doesn’t function easily or at all. • Check that the battery is loaded in the remote control or the battery is not weak. (See page 8.)
• Check that the remote control sensor isn’t exposed to direct sunlight or fluorescent light. (See page 8.)
• Use the remote control within its operation range. (See page 8.)
Abnormal sound is heard. • Because the color wheel spins at a high speed, metallic
 sounds may be heard in rare occasions. Such symp-
tom is not a malfunction.
ProblemSolution
The projector does not turn on. • Fit the lamp cover securely. (See page 20.)
The POWER lights amber and the STATUS lights 
green. • Reset the lamp operating time. (See page 20.) 
						

							
EN-24
Indicators
This projector has two indicators, each of which shows the operation condition of the projector. 
The following offer solutions to possible problems. If these pr oblem persist, turn the projector off and consult your dealer.
Normal condition
Abnormal condition
POWERSTATUSCONDITIONNOTE
Stand-by
The projector is in good condition.
The projector is shutting and the fan motor is cooling the lamp for 
shutdown. Do not unplug the power cord or turn the power off 
before the POWER LED changes to flashing. The fan motor will 
turn off when the lamp has been cooled.
STATUS indicator
POWER indicator
Blinking green
Off
Steady green
Steady green
Steady amberSteady amber
POWERSTATUSCONDITIONPOSSIBLE SOLUTION
The projector system has some problems with its fan, so the pro-
jector cannot start up. Contact your dealer.
The lamp has reached its end of life and must be changed soon. 
The lamp will continue to operate un til it fails. Change the lamp. If 
the lamp is off, then the ballast will become malfunction.  (during 
power on) Replace the lamp and reset the lamp operation time.
Temperature is too high. The lamp will turn off. The fan motor is 
cooling the lamp. Wait until the lamp cools down, and the projector 
enters stand-by mode.
The lamp ignition failed.  Replace the lamp and reset the lamp operation time.
Temperature is too high or temperatures sensor is error during 
stand-by mode. • Wait for 1 hour until the lamp cools down, and 
turn the power back on. 
• If the temperature is still high after 1 hour, con-
tact your dealer. 
Steady greenBlinking green
Steady amber
Steady green
Steady greenBlinking red
Steady amber
Off
Blinking greenBlinking red 
						

							
EN-25
ENGLISH
Specifications
• The specifications and outside appearance of the projector are subject to change without prior notice. 
Type DLP™ DATA projector 
Model XD210U/SD210U
Rated power supply 100 - 240 V AC, 50 / 60 Hz 
Rated input 2.5 A
Display Technology0.55-inch Single chip Digital Micromirror Device (DMD) 
XD210U: Pixels 1024 x 768 = 786432 pixels
SD210U: Pixels 800 x 600 = 480000 pixels
Colors 16770000 colors
Projection lens F 2.5 - 2.7, f = 22.0 - 24.2 mm
Light source lamp 180 W
Picture size 30 - 300 inch (aspect ratio 4:3) 
PC compatibility Resolution:640x480 (Expand) - 1024x768 (Real) - 1280x1024 (Compress)
Sync on Green available
Video compatibility NTSC / NTSC 4.43 / PAL (including PAL-M, N) / SECAM, PAL-60 
Component Video (DVD/HDTV) (480i, 576i, 480p, 576p, 1080i, 720p)
Speaker 2W x 1  / 16 ohm
Video input 1.0 Vp-p 75  Ω (negative sync.) 
Audio input 350 mVrms, 10 k Ω or more 
Analog RGB input RGB: 0.7 Vp-p 75 
Ω (negative sync.) 
YP
BPR/YCBCR : Y:1.0 Vp-p (negative sync.) PBPR/CBCR:0.7 Vp-p 
Control connector Serial terminal (RS-232C) (Mini-Din)
Outside dimensions 302 x 104.5 x 221 mm (width x height x depth)
Weight Approx.  2.6 kg 
Length of power cord 114 inch (1.8 m)
Temperature, humidity
(performance guaranteed) +41
°F (+5°C) - +95°F (+35°C), 30 - 90%  
						

							
EN-26
Specifications (continued)
Connectors
Dimensional drawings (unit : mm)
What’s included in the box
Replacement part
15
11
6 10
15
pin No.Spec.
1R(RED)/C
R
2 G(GREEN)/Y
3B(BLUE)/C
B
4NC
5GND
6GND
7GND
8GND
9 DDC5V
10 -
11 -
12 DDC Data
13 HD/CS
14 VD
15 DDC Clock
COMPUTER IN(D-SUB 15-pin)
AC power cord
1 RGB cable for PC for US J2552-0063-01
for EU J2552-0066-01
for UK J2552-0065-01
J2552-0072-03 2 Remote control with battery
 
(One is installed in the main body)
1 Safety manual/Quick start up
1 CD-ROM
1  Lens cap
1 Soft case
1 Cap RC lock button
(Option / Not included in the box)
Spare lamp for XD210U/SD210U VLT-XD210LP
221
104.5
302 
						

							
EN-27
ENGLISH
Specifications (continued)
Specification of RGB signals in each computer mode of the projector 
Important:
• Some computers aren’t compatible with the projector.
• The projector’s maximum resolution is 1024 x 768 pixels. It may not display images of higher resolutions than 1024 x 768 (or 800 x 600) cor-
rectly.
• Images with SYNC on G (Green) signal may jitter.
• Images with SYNC on G (Green) signal may be tinged with green.
• If the resolution and frequency of your computer aren’t shown on the table, find the compatible resolution and frequency by ch anging the resolu-
tion of your computer.
• When connecting a HDTV decoder having RGB output terminals, set Signal Type to RGB in the Setting menu.
• Video signal with 4 line (R, G, B, CS) and 5 line (R, G, B, H, V) is not supported.
• The resolutions of 640 x 480 (72 Hz) and 640 x 480 (75Hz) do no t support images with SYNC on G (Green) and Composite Sync.
Signal mode resolution horizontal
frequency (kHz)vertical
frequency (Hz) XD210U
(H x V) SD210U
(H x V)
NTSC (60), 480i (60) - 15.73 59.94 1024 x 768 800 x 600
PAL (50), 576i (50) -15.63  50.00 1024 x 768 800 x 600
1080i (60) - 33.75 60.00 1024 x 576 800 x 450 1080i 50 - 28.13  50.001024 x 576 800 x 450
480p (60) - 31.47 59.94 1024 x 768 800 x 600
576p  (50) - 31.25 50.00 1024 x 768 800 x 600
720p  (60) - 45.00 60.00 1024 x 576 800 x 450
720p  (50) - 37.50 50.00 1024 x 576 800 x 450
VGA 640 x 400
24.82 56.42 1024 x 640 800 x 500
37.86 84.13 1024 x 640 800 x 500
37.86 85.08 1024 x 640 800 x 500
640 x 480 31.47 59.94 1024 x 768 800 x 600
37.86 72.81 1024 x 768 800 x 600
37.50 75.00 1024 x 768 800 x 600
43.27 85.01 1024 x 768 800 x 600
SVGA 800 x 600 35.16 56.25 1024 x 768 800 x 600
37.88 60.32 1024 x 768 800 x 600
48.08 72.19 1024 x 768 800 x 600
46.88 75.00 1024 x 768 800 x 600
53.67 85.06 1024 x 768 800 x 600
XGA 1024 x 768 48.36 60.00 1024 x 768 800 x 600
56.48 70.07 1024 x 768 800 x 600
60.02 75.03 1024 x 768 800 x 600
62.94 74.92 1024 x 768 800 x 600
68.68 85.00 1024 x 768 800 x 600
SXGA 1152 x 864
63.85 70.01 1024 x 768 800 x 600
67.50 75.00 1024 x 768 800 x 600
1152 x 900 61.85 66.00 984 x 768 768 x 600
71.81 76.84 984 x 768 768 x 600
1280 x 960 60.00 60.00 1024 x 768 800 x 600
1280 x 1024 63.98 60.02 960 x 768 750 x 600
MAC 640 x 480 35.00 66.67 1024 x 768 800 x 600
832 x 624 49.72 74.55 1024 x 768 800 x 600
1024 x 768 60.24 75.02 1016 x 768 800 x 600 
						

							
EN-28
Mitsubishi Projector Warranty, Sales Support and Service Information1 Zusho Baba, Nagaokakyo-City, Kyoto Japan
MITSUBISHI ELECTRIC CORPORATION
MEU-SP (Mitsubishi Electric Europe B.V. Spanish Branch)
http://www.mitsubishielectric.es/
Ctra. de Rubi, 76-80, 08173 Sant Cugat del Valles,
Barcelona, Spain
Sales InquiriesPhone :+34-93.565.31.54
Fax :+34-93.589.43.88
E-mail :[email protected]
Technical Inquiries Phone :+34-93.586.27.51
Fax :+34-93.588.53.87
E-mail :[email protected]
MEU-SWE (Mitsubishi Electric Europe B.V Scandinavian
Branch)
Hammarbacken 14, Box 750, S-19127, Sollentuna, Sweden
Sales Inquiries Phone :+46-(0)8-6251070
Fax :+46-(0)8-6251036
Technical Inquiries Phone :+46-(0)8-6251052
Fax :+46-(0)8-6251036
MEU-UK (Mitsubishi Electric Europe)
http://www.mitsubishi.co.uk/evs/
Visual Information Systems Division, Travellers Lane, Hatfield, Hertfo rdshire, AL10 8XB U.K.
Sales Inquiries Phone :+44 (1707) 278684
Fax :+44 (1707) 278541
E-mail :[email protected]
Technical Inquiries Phone :+44 (870) 606 5008
Fax :+44 (1506) 431927
E-mail :[email protected]
Asia
CHINA (Mitsubishi Electric Air-Conditioning & Visual
Information Systems (Shanghai) Ltd.)
26/F .,Oriental Center ,699 Nanjing Rd(W),Shanghai,
200041,China
Sales Inquiries Phone :+86(21) 5211-0882-3002
Fax :+86(21) 5211-0576
Technical Inquiries Phone :+86(21) 5211-0882-3020
Fax :+86(21) 5211-0576
HONG KONG (Mitsubishi Electric Ryoden Air-Conditioning
& Visual Information Systems (HongKong) Ltd.)
7th Floor, Manulife Tower, 169 Electric Road, North Point,
Hong Kong
Sales Inquiries Phone :+852-2510-1505
Fax :+852-2510-0463
Technical Inquiries Phone :+852-2422-0161
Fax :+852-2487-0181
SINGAPORE (Mitsubishi Electric Asia Pte. Ltd.)
http://www.mitsubishielectric.com.sg
307, Alexandra Road, #05-01/02 Mitsubishi Electric
Building, Singapore 159943
Sales Inquiries Phone :+65-6473-2308
Fax :+65-6475-9503
E-mail :[email protected]
Technical Inquiries Phone :+65-6470-2666
Fax :+65-6475-9503
INDIA (Mitsubishi Electric Asia Pte. Ltd.)
307, Alexandra Road, #05-01/02 Mitsubishi Electric
Building, Singapore 159943
Sales Inquiries Phone :+65-6473-2308
Fax :+65-6475-9503
E-mail :[email protected]
Technical Inquiries Phone :+65-6470-2666
Fax :+65-6475-9503 INDONESIA (Mitsubishi Electric Asia Pte. Ltd.)
307, Alexandra Road, #05-01/02 Mitsubishi Electric
Building, Singapore 159943
Sales Inquiries
Phone :+65-6473-2308
Fax :+65-6475-9503
E-mail :[email protected]
Technical Inquiries Phone :+65-6470-2666
Fax :+65-6475-9503
PHILIPPINES (Mitsubishi Electric Asia Pte. Ltd.)
http://www.mitsubishielectric.com.sg
307, Alexandra Road, #05-01/02 Mitsubishi Electric
Building, Singapore 159943
Sales Inquiries Phone :+65-6473-2308
Fax :+65-6475-9503
E-mail :[email protected]
Technical Inquiries Phone :+65-6470-2666
Fax :+65-6475-9503
VIETNAM (Mitsubishi Electric Asia Pte. Ltd.)
307, Alexandra Road, #05-01/02 Mitsubishi Electric
Building, Singapore 159943
Sales Inquiries Phone :+65-6473-2308
Fax :+65-6475-9503
E-mail :[email protected]
Technical Inquiries Phone :+65-6470-2666
Fax :+65-6475-9503
STC (Setsuyo Astec Corporation Seoul Branch)
4F,Dongseo Game Channel Bldg,660-11 Deungchon-Dong,
Kangseo-Ku, Seoul, Korea
Sales & Technical Inquiries Phone :+82-(0)2-2657-9841~3
Fax :+82-(0)2-2657-9900
MALAYSIA (Antah Melco Sales & Services Sdn. Bhd.)
6, Jalan 13/6 46860 Petaling Jaya Selangor, Darul Ehsan,
Malaysia
Sales & Technical Inquiries Phone :+60-(0)3-79552088 (Ext. 203)
Fax :+60-(0)3-79563950/+60-(0)3-79582576
Technical & Service Inquiries Phone :+60-(0)3-79552088 (Ext. 106)
Fax :+60-(0)3-79563950/+60-(0)3-79582576
ME-TWN (Mitsubishi Electric Taiwan Co., Ltd.)
http://www.MitsubishiElectric.com.tw
11TH FL., 90 SEC. 6, CHUNG SHAN N. RD., TAIPEI, 111
R.O.C.
Sales & Technical Inquiries Phone :+886-2-2832-8255
Fax :+886-2-2833-9813
MKY (Mitsubishi Electric Kang Yong Watana Co., Ltd. )
http://www.mitsubishi-kyw.co.th/
Road, Huamark Bangkapi, Bangkok 10240, Thailand
Sales & Technical Inquiries Phone :+66-2-731-6841
Fax :+66-2-379-4763
Oceania
ME-AUST (Mitsubishi Electric Australia)
http://www.mitsubishi-electric.com.au/prod.asp?prod=proj
348 Victoria Road, Rydalmere, N.S.W. 2116, Australia Sales
& Technical Inquiries Phone :+(612)9684-7777
Fax :+(612)9684-7208
E-mail :[email protected]
Technical Inquiries
Phone :+(612)9684-7694
Fax :+(612)9684-7684
E-mail :[email protected]
BDT (Black Diamond Technologies Ltd.)
(Warranty Registration) http://www.bdt.co.nz/projectors/
warranty.asp
1 Parliament St, Lower Hutt, Wellington, New Zealand Sales
Inquiries Phone :+64-(0)4-560-9100
Fax :+64-(0)4-560-9133
E-mail :[email protected]
Technical Inquiries Phone :+64-(0)4-560-9100
Fax :+64-(0)4-560-9133
E-mail :[email protected]
MESCA (Mitsubishi Electric Sales Canada Inc.)
http://www.mitsubishielectric.ca
Information Technologies Group, 4299 14th Avenue,
Markham, Ontario L3R 0J2, Canada
Sales & Technical Inquiries
Phone :+1-(800) 450-6487
Fax :+1-(905) 475-7958
E-mail :[email protected]
Customer Care E-mail :[email protected]
Sales & Inquiries
Phone :Toll Free (888)307-0349
E-mail :[email protected]
Technical Inquiries Phone :Toll Free (888)307-0309
E-mail :[email protected]
Europe
MEU-FRA (Mitsubishi Electric Europe B.V French Branch)
25, Boulevard des Bouvets 92 741, Nanterre CEDEX,
France
Sales Inquiries Phone :+33 (0)1 55-68-55-53
Fax :+33 (0)1 55-68-57-31
Technical Inquiries Phone :+33 (0)1 55-68-56-42
Fax :+33 (0)1 55-68-57-31
MEU-GER (Mitsubishi Electric Europe B.V. German Branch)
http://www.mitsubishi-evs.de/
Gothaer Strasse 8, 40880 Ratingen, Germany
Sales Inquiries Phone :0049 - 2102 - 486 9250
Fax :0049 - 2102 - 486 7320
Technical Inquiries Phone :0049 - 2102 - 486 1330
Fax :0049 - 2102 - 486 1340
MEU-IR (Mitsubishi Electric Europe B.V. Irish Branch)
http://www.mitsubishi.ie/
Westgate Business Park, Ballymount, Dublin 24, Ireland
Sales Inquiries Phone :+353-1-4198807
Fax :+353-1-4198890
Technical Inquiries Phone :+353-1-4198808
Fax :+353-1-4198895
MEU-IT (Mitsubishi Electric Europe B.V. Italian Branch)
Centro Direzionale Colleoni, Palazzo Sirio, Viale Colleoni 7,
20041 Agrate Brianza, Italy
Sales & Technical Inquiries Phone :+39-(0)39-60531
Fax :+39-(0)39-6053214
E-mail :[email protected]
MEU-NL (Mitsubishi Electric Europe B.V. Benelux Branch)
http://www.mitsubishi.nl/LCD/ProdFrame.html
Nijverheidsweg 23A, 3641 RP Mijdrecht, The Netherlands
Sales Inquiries Phone :+31-297-282461
Fax :+31-297-283936
E-mail :[email protected]
Technical Inquiries Phone :+31-297-282461
Fax :+31-297-283936
E-mail :[email protected]
Russia (Mitsubishi Electric Europe B.V Moscow
Representative Office)
http://www.mitsubishi-projector.ru/
Moscow Representative Office, 52/5 Kosmodamianskaya
Nab., 115054, Moscow, Russia
Sales & Technical Inquiries Phone :(7095) 721-2068
Fax :(7095) 721-2071
North America
MDEA (Mitsubishi Digital Electronics America, Inc.)
Presentation Products Division
9351 Jeronimo Road
Irvine, CA 92618, USA
For Warranty Registration, visit:
http://www.mitsubishi-presentations.com under Customer Care