Mitsubishi X30 Projector User Manual

E – 19
ENGLISH
Enlarging the picture
You can enlarge the picture up to ten times the original
size.
Press ZOOM + button.
While the button is pressed the picture is en-
larged until it becomes ten times the original size.
Release the button at the desired size.
ZOOM
Note
The quality of the enlarged picture deteriorates compared to
the original size picture.
Screen Reduction
Press ZOOM – button. When this button is
released, the screen will return to 90%
reduction.
ZOOM
              
Original sizeTen...

E – 20
Menu Structure
The normal menu will be
displayed when the MENU
button is pressed with the
remote control FLIP COVER
closed.
The numerals in parentheses ( ) are reference page numbers.
Normal menu
For VIDEO, S-VIDEO and component video (YCbCr) input
The advanced menu will be
displayed when the MENU
button is pressed with the
remote control FLIP COVER
open.Advanced menu
MENU button
For VIDEO, S-VIDEO and component video (YCbCr) input
Common menu
Common menu
Menu operation
MOUSEPOWER...

E – 21
ENGLISH
Normal menu
RGB input
Advanced menu
• The Advanced menu cannot be used unless the FLIP COVER of the supplied remote control is open.
RGB input
(22)
(22)
(24)
(24)
(24)
(25)
(25)
(26)
(26)
(27)
(27)
(27)
(28)
(28)(26)
(26)
(26)
(29)
(30)
[A]
[C] [B] 

E – 22
The picture elements such as brightness, contrast, white
balance, and so on can be adjusted individually for each
input source. The adjustable items vary depending on the
input source.
(The elements marked with “” are adjustable.)
Input sourceVIDEO/S-VIDEO CONPONENT VIDEO RGB
BRIGHTNESS
CONTRAST
COLOR–
TINT–
SHARPNESS
–
1Select the input source (see page 16)
2Press the MENU button to display the
menu, hold down the cursor $ / % keys
or the MENU button and then select “IM-
AGE”.
3Press the cursor {...

E – 23
ENGLISH
Adjusting the projected image from
the computer
The unit selects the most suitable resolutions as shown in the “Timing Chart” below according to the incoming signals from the RGB/YCbCr
connector. However, you may need manual adjustment depending on the computer. If you have any vertical banding, noise, dot interference,
or crosstalk  on the projected picture, adjust the clock frequency with “PICTURE ADJ” then the clock phase with “FINE PICTURE” (see page
24).  You can also adjust the...

E – 24
Manual Adjustment of Personal
Computer Images
Adjusting Clock Frequency and Phase
1Select RGB as the input (page 16).
2Press the MENU button to display the
main menu and then press the cursor $ /
% keys to select the “IMAGE”.
3Press the cursor { / } keys to select the
“PICTURE ADJ”.
4Press the cursor $ / % keys and adjust
the image width in relation to the screen.
Adjustment is performed in dot units. Adjust to
the position where vertical flicker disappears.
5Press the cursor { / } keys and...

E – 25
ENGLISH
Resetting
Resetting
All items can be reset to the standard settings except as
follows.
•Lamp usage time
•KEYSTONE adjustment values (including the KEY-
STONE setting value: page 28).
1Press the remote control MENU button to
display the normal menu and then press
the cursor $ / % keys to select “INFOR-
MATION”.
2When the INFORMATION menu appears,
press the cursor { / } keys select “RE-
SET”, then press the ENTER button.
3If the ENTER button is not used during
reset, press the CANCEL...

E – 26
Setting the Video Type
1With the FLIP COVER of the remote con-
trol open, press the MENU button to dis-
play the Advanced menu, then use the
cursor $ / % keys to select “COLOR”.
2Use the cursor { / } keys to select
“VIDEO TYPE”.
3Use the cursor $ / % keys to set the
“VIDEO TYPE”.
The following can be selected.

 DVD
 VCR
DVD is used for DVD players and VCR is used for
normal video players.
Selecting the Color System
The following color systems can be used with this device.

 NTSC 3.58
 NTSC 4.43

...

E – 27
ENGLISH
Setting the RGB/YCbCr connector
The RGB/YCbCr connector can be switched and used as
the component video signal (YCbCr) input connector.
1With the FLIP COVER of the remote con-
trol open, press the MENU button to dis-
play the Advanced menu, then use the
cursor $ / % keys to select “COLOR”.
2Use the cursor { / } keys to select
“SOURCE CHANGE”.
3Use the cursor $ / % keys to set the
“SOURCE CHANGE”.
The following can be selected.

 RGB
 YCbCr
When component video (YCbCr) input is used,
use...

E – 28
Setting in Accordance With
Image Contents (continued)
Initial Settings
Setting Keystone
This is used to set the height for keystone adjustment.
1With the FLIP COVER of the remote con-
trol open, press the MENU button to dis-
play the Advanced menu, then use the
cursor $ / % keys to select “VIEW”.
2Display the frame, then use the cursor {
/ } keys to select “KEYSTONE”.
3Use the cursor $ / % keys to select
“NORMAL” or “FULL”.

Normal: normal keystone correction

Full: In this mode, the image is...