Mitsubishi Wd720u Projector User Manual

EN-31
To adjust the tone of white (Color 
Temp.): 
You can select a preset color temperature (white tone) 
using the menu. 
(See page 22 for menu setting.) 
1. Display the Picture menu. 
2. Select Color Temp. by pressing the  or  button. 
3. Select your desired color temperature by pressing 
the  or  button. 
To cancel the menu:
4. Press the MENU button. 
To adjust the tone of white (To customize 
the color temperature): 
To set (and store) a user-defined color temperature, 
perform the following...

EN-32
Image adjustment (continued)
Image
You can set user-defined values for the brightness and 
hue using the menu. (See page 22 for menu setting.)
1. Display the Picture menu.
2. Select Image by pressing the  or  button.
3. Select User  by pressing the  or  button.
4. Press the ENTER button.
•	 The	Image	User	menu	appears.
Image User
AdjustMENUExit
Select
Brilliant Color™
Gamma
Dynamic
10
5. Select a setting you want to set.
Gamma
Use this setting to set an optimal gamma value and 
modulation of...

EN-33
Simple method to adjust the image 
position
To adjust the horizontal position: 
1. Align the left edge of the image with the left side 
of the screen by adjusting H.Position. Then, align 
the right edge of the image with the right side of 
the screen by adjusting Tracking.
2. Repeat step 1 to complete the adjustment of the 
horizontal position.
To adjust the vertical position: 
3. Align the upper edge of the image with the upper 
side of the screen by adjusting V.Position.
LPF (Progressive filter)...

EN-34
Network settings
You can set the network of the projector using the 
menu.
Network Cong
AdjustMENUExit
Select
Pr
ojector Name
Network Certication
Network Passwor d
IP Cong
Wir eless Setting
AMX Device Discovery
Network Initialization
Network Restart
OKOK
OKOK
OKOn
Of f
SET
Setting Projector Name
(See page 22 for menu setting.)
1.  Display the Network Config menu. 
2. Press the  or  button to select Projector Name.
Projector NameSET
3.  Press the  or  button to select SET .
4. Press the ENTER...

EN-35
5. Select OK, and NEW NETWORK PASSWORD 
screen appears if the entered password is correct.
•	 If	the	entered	password	is	not	correct,	the	
CURRENT NETWORK PASSWORD screen 
appears again.
←→↔
∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗
∗∗∗∗∗∗NEW NETWORK P ASSWORD
CONFIRM NETWORK P ASSWORD
OK
capsCLEAR
DEL
CANCEL
BCDEFGHIJKLMNOPQRSTUVWXYZ0123456789
A
6. Enter the NEW NETWORK PASSWORD and 
CONFIRM NETWORK PASSWORD.
•	 Password	can	be	set	using	up	to	32	characters	
including alphabets (capital/small) or numeric...

EN-36
Subnet Mask settings
1. Display the IP Config menu.
2. Press the  or  button to select Subnet Mask.
Subnet Mask-255-255-00
3. Press the ENTER button.
•	 The	first	octet	is	selected.	
Subnet Mask-255-255-00
4. Press the  or  button to select the numeric 
value.
5. Press the  or  button to select the octet.
•	 The	second	or	final	octet	is	selected.	
Subnet Mask-255-255-00
6. Press the ENTER button.
•	 To	cancel	the	setting,	press	the	MENU	button.
•	 Set	the	numeric	value	within	the	range	from	0...

EN-37
Wireless Setting
(See page 22 for menu setting.)
1. Display the Network Config menu.
2. Press the  or  button to select Wireless Setting.
Wir eless SettingOK
3. Press the ENTER button.
•	 The	Wireless	Setting	menu	appears.
Wir eless Setting
AdjustMENUExit
Select
SSID
Channel
Encryption
Wir
eless Setup
OK
Auto
Of fSET
SSID setting
1.  Display the Wireless Setting menu. 
2. Press the  or button to select SSID.
SSIDSET
3. Press the or  button to select SET .
4. Press the ENTER button.
•	 The...

EN-38
•	 The	number	of	characters	of	KEY	varies	
depending on the Encryption setting. 
•	 WEP	128bit(ASCII):	13	chars
•	 WEP	64bit(ASCII):	 5	chars
•	 WEP	128bit(HEX):	 26	digits
•	 WEP	64bit(HEX):	 10	digits
•	 WPA-PSK(ASCII):	 8-63	chars
•	 WPA2-PSK(ASCII):	 8-63	chars
•	 WPA-PSK(HEX):	 64	digits
•	 WPA2-PSK(HEX):	 64	digits
•	 If	the	entered	content	is	outside	character	
number range, the KEY screen appears again 
after an error dialog is displayed.
Wireless Setup setting
1. Display the Wireless...

EN-39
Advanced display utilities
USB Display
You can project the computer images inputted via a 
USB connection.
You don’t have to install any drivers on your computer 
to use this function.
Important:
•	Supported OS’s are Windows XP, Windows Vista  
and Windows 7.
•	Only 1-to-1 screen projection is supported.
•	 Moving	images	cannot	be	displayed.
Connection
Connect the projector and the computer using a 
commercially available USB cable.
ComputerTo USB-B 
terminal
USB 4-pin 
(type B)
To USB port USB...

EN-40
LAN Display
You can project the computer images inputted via a 
wired or wireless LAN.
You can also perform the following during the LAN 
Display projection:
•	 4-to-1	split	screen	projection
 Images from up to 4 computers can be projected 
split on 1 projector screen.
•	 Remote	desktop	
 Connecting an input device such as a mouse or 
keyboard to the USB-A terminal on the projector 
enables the following computer operations from the 
projector.
•	 Showing	local	files	of	the	computer
•	 Operating...