Mitsubishi Wd720u G Projector User Manual

							EN-21
Menu operation
You can make various settings using the displayed menus.
Installation
Closed CaptionStandby Mode
Of
f, On
Option
WXGA
Auto KeystoneLanguageTest Pattern
Passwor dChange Passwor dPassword
Network Config
Video Image
Signal
Information
H.Position
Hold
Set Up
0-999V.Position 0-999Fine sync 0-31Tracking
User 0-2800Clamp Width
1-63
Clamp Position
1-255LPFOn, Off
Overscan 90-100%
Shutter(L) 0-20Shutter(U) 0-20
Shutter(RS) 0-20
On, Off0-2550-2550-255
0-2550-255
Shutter(LS) 0-20
*4
*1
Auto, OffCinema Mode
Efficient Mode *4
*4
*4
Begin
0-99End0-99
*1
*2
Computer Input
Sync. T ype
InputResolutionH.FrequencyV.Fr equency
Auto, RGB, YCbCr/YPbPr
Auto, Of f,	3.75%,	7.50%
Splash Scr eenOriginal, User , OffBack ColorBlue, Black, Image Original, Image UserAV Mute ModeBlack, Image Original, Image UserOff, CC1, CC2, CC3, CC4, T1, T2
Low , LAN, Speaker Out, Monitor Out
*3
Video Signal Auto, NTSC, PAL, SECAM, 4.43NTSC, P AL-M, PAL-N, PAL-60Off,	Auto,	1280x768,	1280x768RB,	1280x800,	1360x768,	1366x768	    
*5
*2
English,           , Español, Français, Italiano,               , \
Deutsch,           , Polski, Português,             , Svensk
a, Indonesia,      , Türkçe, Magyar,           , Bahasa Malaysia
Picture
Brightness ±30
Contrast±30LowMidHigh
ImageAuto
Color ±10Sharpness ±5Tint±10Contrast B
	±30
Brightness R 	±30Brightness G 	±30
Contrast R	±30Contrast G 	±30
Brilliant Color™
Dynamic, Natural, DetailGamma 
Center, Upper , Lower 	0-10
Brightness B
	±30	±30	±30	±30
GainSaturationHue
UserRedGreen
3D Off, On3D Sync Invert Off, On
*1 *1
*1
AudioAudio Input 
V olume 0-21
*1*2
*2
*2
*1*2
IP Addr ess
DHCP
Default Gateway
DHCP FunctionOf
f, Onxx-xx-xx-xx-xx-xxMAC Addr ess
End IP Addr essStart IP Addr ess
IP Config Setup
Subnet Mask
*2
*2
*2
Cyan
Magenta
±10
Off, Onxxxx
NormalAspect Ratio
Full*8
Color T emp.
Auto, Normal, EnhancedInput Level
Color Management
Standar d, Low
Lamp Mode
Blue
Ye
llow
16:9
On
OK
OK
Projector Name
xxxxxxxx..., SET
Network CertificationNetwork Passwor dOKIP Config
Lamp TimeOK
OK
OK
Channel SSID
Wir
eless Setup
Encryption
Wireless SettingOK
Reset AllOK
OK
Image Captur eOK
*7
Theater
Pr esentation
Standard
Black Board
White Board
AutoAudio 1
Audio 3Mix
Audio 2
Of f, Mirr or, Invert, Mirr or InvertImage ReverseAuto Power On Off, On
On   , Of f
AMX Device DiscoveryNetwork InitializationOKNetwork RestartOK
Off   , On
Auto Power Of fOff,	5Min,	10Min,	15Min,	30Min,	60Min
*6 *6
*6
*6
Auto,	1,	2,	3,	4,	5,	6,	7,	8,	9,	10,	11SET    , Of
f,  WEP 128bit(ASCII), WEP 64bit(ASCII), WEP 128bit(HEX), WEP 64bi\
t(HEX),  
WP A-PSK(ASCII), WP A2-PSK(ASCII), WP A-PSK(HEX), WPA2-PSK(HEX)
User
Menu PositionUpper Left, Upper Right, Center
, Lower Left, Lower Right
Cr oss Hatch   , White   , Black
Of f
xxxxxxxx..., SET
*1:  Not available with certain signals.*2: Not available when the input signal is from the VIDEO or S-VIDEO terminal.*3:	Available	only	when	the	input	signal	is	TV60,	TV50,	480i,	or	576i.*4: The range that can be specified varies across input signals.*5: Available only when the input signal is from the VIDEO or S-VIDEO terminal.*6: Audio 1, Audio 2, Audio 3, and Mix  cannot be selected when the input source is HDMI input.*7: “”	is	not	displayed	and	is	not	available	in	WD720U.*8:	This	function	is	not	available	in	WD720U. 
						

							EN-22
How to set the menus
1. Press the MENU button. 
•	 The	Main	Menu	appears	on	the	screen.
Confirm Exit
SelectMENU
Main Menu
opt.
R G BR G B
Pictur e
Video Image
Signal
Audio
Installation
Option
Network Cong
Information
The item being selected is displayed in r ed letters 
on a blue backgr ound.
2. Press the   or  button to select a menu to use. 
Confirm Exit
SelectMENU
Main Menu
opt.
R G BR G B
Pictur e
Video Image
Signal
Audio
Installation
Option
Network Cong
Information
3.  Press the ENTER button (or  button).
•	 The	selected	menu	is	displayed.
Off
Installation
AdjustMENUExit
Select
Ef
cient Mode
Image Reverse
Auto Power On
Auto Keystone
T est Patter n
Language
Reset All English
Of
fOff
Menu Position Upper LeftOK
Cr
oss Hatch
OK
4.  Press the  or  button to select an item to adjust. 
Off
Installation
AdjustMENUExit
Select
Ef
cient Mode
Image Reverse
Auto Power On
Auto Keystone
T est Patter n
Language
Reset All English
Of
fOff
Menu Position Upper LeftOK
Cr
oss Hatch
OK
5.  Set the selected item by pressing the  or  button. 
Off
Installation
AdjustMENUExit
Select
Ef
cient Mode
Image Reverse
Auto Power On
Auto Keystone
T est Patter n
Language English
Of
fOff
Menu Position Lower RightOK
Cr
oss Hatch
Reset AllOK
6.  To cancel the menu, press the MENU button 
several times.
Important:
• When an item marked with “” is selected, pressing 
the ENTER button makes its value effective or 
displays another screen for further setting.
•	 When	the	MENU	button	doesn’t	function,	unplug	
the	power	cord	from	the	wall	outlet.	Wait	about	10	
minutes, plug the power cord in, and try again.
•	 The	menus	and	screens	shown	in	this	manual	may	
be different from those of the actual projector.
Menu operation (continued) 
						

							EN-23
Menu items
Set the following items provided in the respective menus.
Picture menu
Picture
AdjustMENUExit
Select
Image
Brightness
Contrast
Color T
emp.
Color Management
Aspect Ratio
Input Level
3D
3D Sync Invert Auto
Mid
Auto Of f
Of f
Red
Normal
00
ITEMSETTINGFUNCTION
ImageAutoAutomatically sets an optimal color balance based on the input signal. Use this setting for most cases.
TheaterMakes projected images soft and smooth. Best suited for movies.
PresentationMakes projected images bright and crisp.
StandardMakes projected images look natural.
Black BoardReproduces natural color tones when images are projected directly onto a black board.
White BoardReproduces natural color tones when images are projected directly onto a white board.
User Use to set Gamma or BrilliantColor™. (See page 32.)
Brightness±30Adjusts the brightness of projected images. (See page 31.)
Contrast±30Adjusts the contrast of projected images. (See page 31.)
Color Temp.4 optionsAdjusts the color temperature. (See page 31.) 
Color ManagementRed  / Green  / Blue  / Cyan  / Yellow  / Magenta 
You can change to any desired color by adjusting each of Gain, Saturation and Hue of six different colors.  (See page 32.)
Aspect RatioNormalAutomatically sets the aspect ratio in relative to the input signal. Use this setting for most cases.
16:9 Select to expand squeezed (or horizontally compressed) images such as DVD images to 16:9. For	XD700U	only:	Press the ENTER button to select the image display position within the screen from Center, Upper, and Lower.
FullSelect this setting when you want to project images in the full screen.
Input LevelAuto / 
Normal / 
EnhancedFor HDMI signal input:
 Auto:    The proper setting is automatically selected.
 Normal:  Select when grayish black occurs.
 Enhanced:  Select when solid black occurs.(See page 13.)
3D Off / OnSet to On/Off of 3D display.
3D Sync InvertOff / OnSwitches the order of the image for left eye and for right eye.
•	 When	Image	is	switched,	projected	images	may	be	distorted.
Menu operation (continued) 
						

							EN-24
Video Image menu
Video Image
AdjustMENUExit
Select
Color
Sharpness
Tint
0
0
0
ITEMSETTINGFUNCTION
Color±10Adjusts the color tone of projected images. (See page 31.) You cannot select this setting when the Computer1, Computer2, or HDMI is selected as the input source.
Sharpness
±5Adjusts the sharpness of projected images. (See page 31.)
Tint±10Adjusts the color tint of projected images. (See page 31.) You can select this setting only when NTSC is selected as the input signal.
•	 You	cannot	adjust	Tint	when	the	TV50	(PAL,	SECAM)	signal	is	inputted.•	 When	Computer1,	Computer2,	or	HDMI	is	selected,	Tint	does	not	work.
Menu operation (continued) 
						

							EN-25
Signal menu
Signal
AdjustMENUExit
Select
V.
 Position
Fine sync
Computer Input
Overscan
Hold
User
On Auto
90%
00T racking 0
H. Position 0
User
AdjustMENUExit
Select
Clamp Width
Shutter(U)
Shutter(L)
Shutter(LS)
Shutter(RS)
Of
f
1LPF
00
00
Clamp Position1
OK
ITEMSETTINGFUNCTION
H. Position0-999Select this setting to adjust the horizontal position of projected images.V. Position0-999Select this setting to adjust the vertical position of projected images.Fine sync0-31Select this setting to eliminate flickering or blurs, if they appear, when you are viewing projected images.Tracking0-2800Select this setting to eliminate vertical wide stripes, if they appear, when you are viewing projected images.Computer InputAutoAutomatically sets the appropriate setting.RGBSelect this setting when you connect the projector to high definition video equipment having R, G, and B output terminals.YCbCr/YPbPrSelect this setting when you connect the projector to a DVD player or other device having Y, CB, and CR (or Y, PB, and PR) component video output terminals.Overscan100%-90%Use this setting to adjust the display area of projected images.HoldOff / On Use this setting to adjust projected images when flagging occurs in the upper area of the screen.UserOK The Signal-User menu is displayed for the following adjustments. 
Clamp Position1-255Use this setting to correct solid white or solid black that appears in projected images. Clamp Width1-63Use this setting to correct solid black that appears in projected images. LPFOn / OffSelect this setting to enable or disable LPF. Shutter(U)0-20Use this setting to adjust projected images when noise appears in the top part of the image. Shutter(L)0-20Use to adjust the image when noise appears on the bottom part of the image. Shutter(LS)0-20Use this setting to adjust projected images when noise appears in the left half of the image. Shutter(RS)0-20Use this setting to adjust projected images when noise appears in the right half of the image.
•	 Horizontal	strips	may	appear	in	the	enlarged	projected	image,	though	these	conditions	are	not	a	malfunction.•	 When	you	change	the	value	of	the	horizontal	or	vertical	position	drastically,	noise	may	appear.•	 The	adjustable	range	of	the	vertical	position	varies	depending	on	the	type	of	the	input	signal.	The	image	may	be	stationary	even when the value is changed. These conditions are not a malfunction.•	 Shutter	does	not	work	correctly	during	keystone	adjustment.•	 When	you	increase	the	value	of	Overscan,	noise	may	appear	on	the	screen.
Important:•	 You	can	set	the	Picture,	Signal,	and	Signal-User	menus	only	when	the	signal	is	inputted.
Menu operation (continued) 
						

							EN-26
Audio menu
Audio
AdjustMENUExit
Select
V
olume
Audio Input
Auto
16
ITEMSETTINGFUNCTION
Audio InputAutoSelects Audio 1 when the input source is Computer1, selects Audio 2 when the input source is Computer2, selects Audio 3 when the input source is Video/S-Video, and selects HDMI when the input source is HDMI.
Audio 1 / Audio 2 / 
Audio 3Selects audio input.
Mix 
Selects mix signal of Audio 1 and Audio 2. You can change the balance of 
Audio 1/Audio 2 using Mix .
Volume 0-21Adjusts the volume of the audio from the speaker.
•	 In	Audio 	Input, 	HDMI 	audio 	is 	selected 	when 	the 	input 	source 	is 	HDMI 	input. 	The 	audio 	of 	Audio 	1, 	Audio 	2, 	Audio 	3, 	and 	Mix 	 cannot be selected.
Menu operation (continued) 
						

							EN-27
Installation menu
Off
Installation
AdjustMENUExit
Select
Ef
cient Mode
Image Reverse
Auto Power On
Auto Keystone
T est Patter n
Language
Reset All English
Of
fOff
Menu Position Upper LeftOK
Cr
oss Hatch
Efcient Mode
AdjustMENUExit
Select
Lamp Mode
Standar
d
Auto Power Of f 5MinStandby Mode Low
OK
ITEMSETTINGFUNCTION
Efficient ModeOK Displays the Efficient Mode menu for the following settings.
 
Lamp ModeStandardSelect this option when you want to view images in a well-lit room.
LowSelect to moderate the intensity of the lamp. The operating sound is reduced and the lamp lifetime becomes longer.•	 When	this	mode	is	switched,	projected	images	may	flicker.•	 If	this	mode	is	frequently	switched,	the	lamp	may	be	deteriorated.
 Standby ModeLowSelect this option when you don’t use the LAN control, speaker output and monitor output during power standby. This option disables them and reduces the power consumption during the power standby.
LANSelect this option when you control the projector via the LAN during power standby.
Speaker OutSelect this option when you want to output audio from the speaker during power standby.
Monitor OutSelect this option when you want to output video signal from the MONITOR OUT terminal in addition to the audio from the speaker during power standby.
 Auto Power OffOff	/	5-60	MinSelects a desired timer setting until the projector enters the standby mode when there is no signal input from the source.
Menu Position5 optionsUse this setting to change the position of the menu on the screen.
Image ReverseOffSelect this setting when you want to view images from the front with the projector set on the floor.
MirrorSelect this setting when you want to view images from behind the screen with the projector set on the floor.
InvertSelect this setting when you want to view images from behind the screen with the projector set at the ceiling.
Mirror InvertSelect this setting when you want to view images from the front with the projector set at the ceiling.
Auto Power OnOff / OnWhen this mode is set to On, the lamp is automatically lit when the power cord is plugged in the wall outlet. Select On when you set the projector at the ceiling.•	 When	the	lamp	is	off,	the	projector	is	in	standby.	Use	the	remote	control	to	turn on the lamp.
Auto KeystoneOff / OnSelect Auto Keystone function.
Test PatternCross Hatch Select to show the test cross hatch pattern.
White Select to show the maximum brightness image.
Black Select to show the minimum brightness image.
Language18 languagesSelects a desired language for the menu.
Reset AllOK Resets all menu settings except for Password and Language to the default.
•	 You	can	display	the	Efficient	Mode	menu	also	by	pressing	the	EFFICIENT	MODE	button.•	 Regardless	of	the	setting	of	Lamp	Mode	in	the	Installation	menu,	the	Standard	lamp	mode	is	activated	by	default	whenever	the projector is turned on.  The Lamp Mode is set to either Standard or Low depending on the setting last selected, and you cannot switch the Lamp Mode in about one minute after the lamp is on.•	 When	the	Standby	Mode	is	set	to	Speaker	Out	or	Monitor	Out,	the	audio	selected	with	Audio	Input	in	the	Audio	menu	is	output	during standby mode. However, no audio is output when the last selected input was HDMI.•	 During	standby	mode,	you	cannot	change	the	audio	input	and	the	volume	from	the	speaker.•	 When	Standby	Mode	is	set	to	LAN,	Speaker	Out,	or	Monitor	Out,	the	fans	rotate	at	very	low	speed	during	standby	after	plugging the power cord (with 5 second high speed rotation at the beginning) and after turning off the lamp. This is to cool down the projector operating various functions during standby and is not a malfunct\
ion. When Standby Mode is set to Low, the fans stop during standby.•	 To	cancel	the	test	pattern,	press	any	button.	
Menu operation (continued) 
						

							EN-28
Option menu
Option
AdjustMENUExit
Select
Passwor
d
WXGA
Set Up
Image Captur e
Splash Scr een
Back Color
AV  Mute Mode Of
f
Original Blue
BlackOf f
Auto
Video Signal AutoCinema ModeAuto
Closed CaptionOK
OK
ITEMSETTINGFUNCTION
PasswordOK Use this setting to activate or deactivate the password lock.
Cinema ModeAuto / OffSelect Auto to automatically activate the film mode when the input video signal is a video signal from a film.
Video Signal8 optionsSelect Auto to automatically set the appropriate video format in relative to the input signal. If projected images aren’t displayed correctly, select a desired video format manually.
WXGAOff	/	Auto	/	1280	x	768	/	1280	x	768RB	/	1280	x	800	/	1360	x	768	/	1366	x	768
Select the appropriate format when the input signal is a WXGA video signal and the Auto mode does not display images properly.Select Off when the input signal is other than a WXGA video signal.
Set UpAutoSelect this setting to automatically change the Set Up mode.
OffSelect this setting to lower the density of black. Use this setting when images are dark.
3.75%	/	7.50%Select this setting to increase the density of black.•	 When	7.50%	is	set,	the	brightness	is	decreased	by	the	setup	cancel function for the U.S.
Image CaptureOK Use to capture the screen for the splash screen. (See page 47.)
Splash ScreenOriginalDisplays the original image for the splash screen when the projector is powered on.
UserDisplays the image captured for the splash screen when the projector is powered on.
OffDisplays no splash screen when the projector is powered on.
Back ColorBlue / BlackDisplays blue or black background while no signal is inputted.
Image OriginalDisplays the original image for the splash screen while no signal is inputted.
Image UserDisplays the image captured for the splash screen while no signal is inputted.
AV Mute ModeBlackDisplays black background when the AV MUTE button is pressed.
Image OriginalDisplays the original image for the splash screen when the AV MUTE button is pressed.
Image UserDisplays the image captured for the splash screen when the AV MUTE button is pressed.
Closed CaptionOffDoes not display captions.
CC1 / CC2 / CC3 / CC4 / T1 / T2Displays captions.
•	 You	can	select	Cinema	Mode	only	when	the	input	signal	is	a	TV60,	TV50,	480i,	or	576i	video	signal.•	 Captions	are	not	displayed	while	information	about	the	menu,	volume	setting,	or	input	signal	selection	is	being	displayed	on	the screen.•	 The	closed	caption	function	displays	text	information	included	in	the	NTSC	signal,	which	is	mainly	used	for	TV	broadcasting	in	North America.
Menu operation (continued) 
						

							EN-29
Network Config menu
Network Cong
AdjustMENUExit
Select
Pr
ojector Name
Network Certication
Network Passwor d
IP Cong
Wir eless Setting
AMX Device Discovery
Network Initialization
Network Restart
OK
SET
OK
OKOK
OK
Wir eless Setting
AdjustMENUExit
Select
SSID
Channel
Encryption
Wir
eless Setup
OK
Auto
Of f
MENU
IP Cong
Adjust Exit
Select
DHCP
IP Addr
ess
Subnet Mask
Default Gateway
MAC Addr ess
DHCP Function
Start IP Addr ess
End IP Addr ess
IP Cong Setup
On
OK
xx-xx-xx-xx-xx-xx Of f
169-
-
-255
169 254-
-
-255
254 0-
-
-0
0220
0
169 -
-169 254
--254 0
--254 221
2541
On
Of
f
SET
ITEMSETTINGFUNCTION
Projector Namexxxxxxxx...Displays Projector Name. Displays Projector Name in blank when Projector Name is not set.
SET Set Projector Name. Enter up to 15 character alphabets (capital/small), numeric characters, or marks.
Network CertificationOn  / Off  Select whether to enable the network certification or not. Select On for normal use.
Network PasswordOK Set the password for PJLink certification. 
IP ConfigOK Select this setting for IP Configuration. (See page 35.)
  DHCPOn / Off Use this setting when you obtain IP Config automatically by DHCP server.
 IP Addressxxx-xxx-xxx-xxxDisplays IP Address.
 Subnet Maskxxx-xxx-xxx-xxxDisplays Subnet Mask. 
 Default Gatewayxxx-xxx-xxx-xxxDisplays Default Gateway. 
 MAC Addressxx-xx-xx-xx-xx-xxDisplays MAC Address.
 DHCP FunctionOn / Off Use this setting when the projector behaves as a DHCP server.
 Start IP Addressxxx-xxx-xxx-xxxDisplays Start IP Address. However, Start IP Address is not set as factory default, and cannot be displayed.
 End IP Addressxxx-xxx-xxx-xxxDisplays End IP Address. However, End IP Address is not set as factory default, and cannot be displayed.
 IP Config SetupOK Set the IP configuration.
Wireless SettingOK Select this setting for wireless configuration.
 SSIDxxxxxxxx...Displays SSID. 
SET Set SSID. Enter up to 32 characters (alphabets or numeric characters).
 ChannelAuto / 1 / 2 / 3 / 4 / 5 / 6	/	7	/	8	/	9	/	10	/	11Select the wireless channel.
 EncryptionSET  / Off / WEP 128bit(ASCII) / WEP 64bit(ASCII) / WEP 128bit(HEX) / WEP 64bit(HEX) / WPA-PSK(ASCII) / WPA2-PSK(ASCII) / WPA-PSK(HEX) / WPA2-PSK(HEX)
Select the wireless encrypted communication.
 Wireless SetupOK Set the wireless configuration.
AMX Device DiscoveryOff  / On  Use this setting when using an AMX controller.
Network InitializationOK Initializes network setting.
Network RestartOK Restarts network function.
Menu operation (continued) 
						

							EN-30
Information menu
Information
MENUExit
Lamp Time
H. Fr
equency
V.  Fr equency
Sync. T ype 2000H
60.00 kHz 60.00 Hz 3Wir e
Resolution
1024x768
Input
Computer1
ITEMDESCRIPTION
Lamp TimeThis menu shows a lamp operating time (hour) calculated assuming that \
Lamp Mode is Low. 
•	 When	the	Lamp	Mode	is	Standard,	this	menu	shows	a	longer	lamp	operating	time	than	the	
actual time. (See page 52 for the interval of lamp replacement.)
InputIndicates the name of the terminal to which the currently projected video signal is being 
inputted.
ResolutionIndicates the resolution of the currently projected video signal. 
H. Frequency
Indicates the horizontal frequency of the currently projected video signal. 
V. FrequencyIndicates the vertical frequency of the currently projected video signal. 
Sync. TypeIndicates the type of the sync signal for the currently projected video signal. 
Menu operation (continued)