Mitsubishi Wd620u Projector User Manual

							EN-21
ENGLISH
Menu operation (continued)
DETAIL MENU* Menus are not displayed when no signal is supplied to the projector.
IMAGE
INSTALLATION
FEATURE
SIGNAL
INFORMATIONCOLOR ENHANCER
CONTRASTBRIGHTNESS
COLOR TEMP.
AUTOPRESENTATIONSTANDARD
±30±30STANDARD
COLOR *1
TINT *1
SHARPNESS *1
ADVANCED MENU
±10±10±5
WALL SCREEN
LAMP MODE
STANDBY MODE
AUDIO INPUT
AUTO KEYSTONE
IMAGE REVERSE
ADVANCED MENU
STANDARD, LOWSTANDARD, LOWAUTO, AUDIO 1, AUDIO 2, AUDIO 3, MIX       *6
BLACK BOARDWHITE BOARDOFF
OFF, MIRROR, INVERT, MIRROR INVERT
LOW
GAMMA MODE
BrilliantColor TMRGB-COLOR
RGB-TINT
HIGHCONTRAST R
CONTRAST G
CONTRAST B
BRIGHTNESS R
BRIGHTNESS G
BRIGHTNESS B
NOISE REDUCTION *1
CTI *1
INPUT LEVEL
DYNAMIC, NATURAL, DETAIL0-10±10±10
±30±30±30±30±30±30
ON, OFFON, OFF±5CLOSED CAPTION *1
AUTO POWER ON
AUTO POWER OFF
IMAGE CAPTURE
SPLASH SCREEN
BACK COLOR
AV MUTE MODEOFF, CC1, CC23D *8ON, OFF3D SYNC. *81, 2
ON, OFFOFF, 5min, 10min, 15min, 30min, 60min
ON, OFFBLUE, BLACK, IMAGEBLACK, IMAGE 1-5
1-5
1-5
1-5
 ASPECT
SETUP *1
LANGUAGE
RESET ALL PASSWORD FUNCTION
MENU POSITION
CINEMA MODE *3
VIDEO SIGNAL *5
WXGA *2
NORMAL
AUTO, OFF, 3.75%, 7.5%
DISPLAY INPUT      , MENU ACCESS      , SPLASH ID SCREEN 1 (upper left),  2 (lower right)
FULL
AUTO, OFFAUTO, NTSC, PAL, SECAM, 4.43NTSC, PAL-M, PAL-N, PAL-60OFF, AUTO, 1280 x 768, 1280 x 768RB, 1360 x 768, 1366 x 768, 1280 x 800
LOCK
*4
*4
*4
*4CENTER, UPPER, LOWER
OVER SCAN
HOLD *2 HORIZ. POSITION
VERT. POSITION
FINE SYNC. *1 *2
TRACKING *2
COMPUTER INPUT *2
100-90%OFF
0-9990-9990-310-2800AUTO, RGB, YCBCR/YPBPR
NETWORK PROJECTOR NAME
NETWORK PASSWORD
NETWORK RESET PJlink CERTIFICATIONIP CONFIGBEGIN
END
SHUTTER (L)
SHUTTER (LS)
SHUTTER (RS) CLAMP POSITION *2
CLAMP WIDTH *2
VERT. SYNC
LPF *1 *2
SHUTTER (U)
0-990-99
0-200-200-20
1-2551-63AUTO, OFFON, OFF0-20
SYNC. TYPE *2 LAMP TIME  (LOW)
INPUT
RESOLUTION
VERTICAL FREQUENCY
HORIZONTAL FREQUENCY
OK     UNLOCKOK     
OK     
USEROK     
OK     
OK     
OK     
*****..., SET     
DHCP
IP ADDRESS
SUBNET MASK
DEFAULT GATEWAY
MAC ADDRESS
xx-xx-xx-xx-xx-xx
***.***.***.***, SET     ***.***.***.***, SET     ***.***.***.***, SET     
ON     
OK     
USER     
USER     
OK     
BEIGE     LIGHT BLUE     LIGHT GREEN     PINK     
16:9      *7
, SVENSKA, POLSKI
ON, OFF±10
GO     
THEATER
ON     , OFF
ON     , OFF
 *8
*1 Not available with certain signals
*2 Not available when the input signal is from the VIDEO IN or S-VIDEO IN terminal.
*3 Available only when the input signal is TV60, TV50, 480i, or 576i.
*4 The range that can be specified varies across input signals.
*5 Available only when the input signal is from the VIDEO IN or S-VIDEO IN terminal.
*6 AUDIO 1, AUDIO 2, AUDIO 3, and MIX
  cannot be selected when the Input Source is HDMI input.
*7   is not displayed and is not available in WD620U/WD620U-G.
*8 This function is not available in WD620U/WD620U-G. 
						

							EN-22
Menu operation (continued)
Basic operationSeveral settings can be adjusted using the menu.
Example : Auto power off time setting
1. Press the MENU button.
2. Select the DETAIL MENU and press the ENTER button  (or T 
button).
3. Press the W or X button to select INSTALLATION. 
4. Press the ENTER button (or T button).5. Press the S or T button to select AUTO POWER OFF.
6. Press the W or X button to adjust the auto power off time.
7. Exit the menu by pressing the MENU button several times.
Important:  When the button doesn’t function, unplug the power cord from the 
wall outlet. Wait about 10 minutes, plug the power cord in, and try 
again.
 After selecting the items marked with  , press the ENTER but-
ton.
Menu OptionsSet the following options provided in the respective menus.
1. IMAGE menu
 You cannot adjust TINT when the TV50 (PAL, SECAM) signal is inputted.
 You cannot adjust COLOR TEMP. when WALL SCREEN is set to other than OFF.
 When COMPUTER 1 or COMPUTER 2 or HDMI is selected, TINT do not work.
 When COLOR ENHANCER is switched, projected images may be distorted.
 Captions are not displayed while information about the menu, volume setting, or input signal selection is being displayed on the screen.
 The closed caption function displays text information included in the NTSC signal, which is mainly used for TV broadcasting in North America.
*1 This function is not available in WD620U/WD620U-G.
opt.
IMAGE
opt.
INSTALLATION
WALL SCREEN
BEIGE
opt.
INSTALLATION
AUTO POWERON 
AUTO POWER
OFFOFFON
AUTO POWERON 
AUTO POWER
OFFOFF30min
Menu option Setting Feature description
IMAGE ADVANCED menu
COLOR ENHANCERAU TOAutomatically sets an optimal color balance based on the input signal. 
Use this setting for most cases.
PRESENTATION Makes projected images bright and crisp.
STANDARD Makes projected images look natural.
THEATER Makes projected images soft and smooth. Best suited for movies.
USER
 Adjusts the gamma curve, color intensity, or balance. (See page 27.)
CONTRAST±30 Adjusts the contrast of projected images. (See page 27.)
BRIGHTNESS±30 Adjusts the brightness of projected images. (See page 27.)
COLOR TEMP. 4 optionsAdjusts the color temperature. You cannot select this setting when 
WALL SCREEN in the INSTALLATION menu is set to a setting other 
than OFF. (See page 27.)
COLOR±10Adjusts the color tone of projected images. (See page 27.) You cannot 
select this setting when the COMPUTER 1 or COMPUTER 2 or HDMI is 
selected as the input source.
TINT±10Adjusts the color tint of projected images. (See page 27.) You can select 
this setting only when NTSC is selected as the input signal.
SHARPNESS±5 Adjusts the sharpness of projected images. (See page 27.)
ADVANCED MENU OK
 NOISE REDUCTIONON/OFF Reduces noise of projected images when the input signal is noisy.
CTI ON/OFF Corrects smeared color borders.
INPUT LEVEL±5Adjusts the input level of analog video signals.
The input level of the video signal varies across devices to which the 
projector is connected. A high input level causes projected images to 
appear solid white, and a low input level causes projected images to 
appear dark.
CLOSED CAPTIONOFF Does not display captions.
CC1/CC2 Displays captions.
3D *1ON/OFF Set to ON/OFF of 3D display.3D SYNC. *11/2 Switches the order of the image for left eye and for right eye.
CONTRAST
BRIGHTNESS0
0
STANDARD
0
COLORCOLOR TEMP.
0
SHARPNESS
AUTOCOLOR
ENHANCER
opt.
IMAGE
0TINT
OKADVANCED MENU
CTI
INPUT LEVEL0 ON
ON NOISE REDUCTION
CLOSED CAPTIONOFF3DON3D SYNC.1
opt.
IMAGEADVANCED MENU 
						

							EN-23
ENGLISH
Menu operation (continued)
2. INSTALLATION menu
 By default, the LAMP MODE is set to STANDARD. The LAMP MODE is set to either STANDARD or LOW depending on the setting last selected, 
and you cannot switch the LAMP MODE in about one minute after the lamp is on.
 In AUDIO INPUT, HDMI audio is selected when the Input Source is HDMI input. The audio of AUDIO 1, AUDIO 2, AUDIO 3, and MIX   cannot 
be selected.
Menu option Setting Feature description
INSTALLATION 
ADVANCED menu
WA LL  SC R EE NOFF/BEIGE
 / LIGHT 
BLUE / LIGHT GREEN / PINK /BLACK 
BOARD/WHITE BOARDSelects a desired setting based on the color of the screen or wall 
on which images are projected. (See page 18.) When selecting a 
setting other than BLACK BOARD/WHITE BOARD, you can fine-
tune the color tone to the desired level on the 1 to 5 scale.
LAMP MODESTANDARDSelect this setting when you want to view images in a well-lit 
room.
LOWSelect this setting when you want to view images at a moderate 
light intensity. The operating sound is consequently reduced, and 
the lamp lifetime becomes longer.
 When this mode is switched, projected images may flicker.
 If this mode is frequently switched, the lamp may be deterio-
rated. 
STANDBY MODESTANDARD LAN can be activated in STANDARD MODE.
LOWPower consumption can be lowered when selecting LOW. How-
ever, LAN and MONITOR OUT cannot be activated.
AUDIO INPUTAUTOIf AUTO is selected, selects AUDIO 1 when the input source is 
COMPUTER 1, selects AUDIO 2 when the input source is COM-
PUTER 2, selects AUDIO 3 when the input source is VIDEO/S-
VIDEO, selects HDMI when the input source is HDMI.
AUDIO 1/AUDIO 2/AUDIO 3 Select the audio input.
MIX
 Selects MIX signal of AUDIO 1 and AUDIO 2. You can change the 
balance of AUDIO 1/AUDIO 2 using MIX .
AUTO KEYSTONE ON/OFF Select Auto Keystone function.
IMAGE REVERSEOFFSelect this setting when you want to view images from the front 
with the projector set on the floor.
MIRRORSelect this setting when you want to view images from behind the 
screen with the projector set on the floor.
INVERTSelect this setting when you want to view images from behind the 
screen with the projector set at the ceiling.
MIRROR INVERTSelect this setting when you want to view images from the front 
with the projector set at the ceiling.
ADVANCED MENU OK
 
AUTO POWER ON ON/OFFWhen this mode is set to ON, the lamp is automatically lit when 
the power cord is plugged in the wall outlet. Select ON when you 
set the projector at the ceiling.
 When the lamp is off, the projector is in standby. Use the 
remote control to turn on the lamp.
AUTO POWER OFF OFF/5-60 minSelects a desired timer setting until the projector enters the 
standby mode when there is no signal input from the source.
IMAGE CAPTURE GO
 Use to capture the screen for the splash screen. (See page 32.)
SPLASH SCREEN ON/OFFSelect ON to display the splash screen when the projector is pow-
ered on.
BACK COLOR BLUE/BLACK/IMAGESelects the background color that is displayed when there is no 
signal input from the source.
AV MUTE MODE BLACK/IMAGEUse to choose the background, either BLACK, or IMAGE, which 
will be displayed when the AV MUTE button is pressed. When 
IMAGE is chosen, the splash screen will be displayed.
LAMP MODE
OFFAUTO KEYSTONE OFF IMAGE 
REVERSE
WALL SCREEN
BEIGE
STANDBY MODESTANDARDSTANDARD
AUDIO INPUTAUTO
opt.
INSTALLATION
OKADVANCED MENU
opt.
INSTALLATIONADVANCED MENU
AUTO POWER
OFF OFF OFFAUTO POWER
ON 
IMAGE CAPTUREONSPLASH
SCREEN ONBACK COLORBLUEAV MUTE MODEBLACK
GO 
						

							EN-24
Menu operation (continued)
3. FEATURE menu
 You can select CINEMA MODE only when the input signal is a TV60, TV50, 480i, or 576i video signal.
*1  is not displayed and is not available in WD620U/WD620U-G.
*2 This function is not available in WD620U/WD620U-G.
Menu option Setting Feature description
ASPECTNORMALAutomatically sets the aspect ratio in relative to the input signal. Use 
this setting for most cases.
16:9
  *1
Selects a desired screen position for anamorphically squeezed or hor-
izontally compressed images stored on DVD disks. 
You can select from CENTER, UPPER, and LOWER by pressing the 
ENTER button. (*2)
FULL Select this setting when you want to project images in the full screen.
PASSWORD FUCNTION  Use this setting to activate or deactivate the password lock.
MENU POSITION 2 options Use this setting to change the position of the menu on the screen.
CINEMA MODE AUTO/OFFSelect Auto to automatically activate the film mode when the input 
video signal is a video signal from a film.
VIDEO SIGNAL 8 optionsSelect Auto to automatically set the appropriate video format in rela-
tive to the input signal. If projected images arent displayed correctly, 
select a desired video format manually.
WXGAOFF/AUTO/1280 x 768/
1280 x 768RB/
1360 x 768/ 1366 x 768/
1280 x 800Select the appropriate format when the input signal is a WXGA video 
signal and the AUTO mode does not display images properly.
Select OFF when the input signal is other than a WXGA video sig-
nal.
SETUPAUTO Select this setting to automatically change the SETUP mode.
OFFSelect this setting to increase the density of black. Use this setting 
when images are dark.
3.75%/7.5%Select this setting to lower the density of black.
 When 7.5% is set, the brightness is decreased by the setup can-
cel function for the U.S.
LANGUAGE 12 languages Selects a desired language for the menu.
RESET ALL OK
 Resets all menu settings except for PASSWORD FUNCTION and 
LANGUAGE to the default.
NORMAL
AUTO
MENU POSITION
VIDEO SIGNAL?
ASPECT
RESET ALLEnglish
LANGUAGEAèOK
DISPLAY INPUTPASSWORD
FUNCTION
CINEMA MODEAUTO1.
SETUP
AUTOWXGAAUTOWXGA
FEATURE
opt. 
						

							EN-25
ENGLISH
Menu operation (continued)
4. SINGAL menu
 Horizontal strips may appear in the enlarged projected image, though these conditions are not a malfunction.
 When you change the value of the horizontal or vertical position drastically, noise may appear.
 The adjustable range of the vertical position varies depending on the type of the input signal. The image may be stationary even when the value 
is changed. These conditions are not a malfunction.
 SHUTTER does not work correctly during keystone adjustment.
 When you increase the value of OVER SCAN, noise may appear on the screen.
Important: You can set the IMAGE, SIGNAL, and SIGNAL-USER menus only when the signal is input.
5. NETWORK menu
Menu option Setting Feature description
SIGNAL USER menu
HORIZ. POSITION 0-999 Select this setting to adjust the horizontal position of projected images.
VERT. POSITION 0-999 Select this setting to adjust the vertical position of projected images.
FINE SYNC. 0-31Select this setting to eliminate flickering or blurs, if they appear, when 
you are viewing projected images.
TRACKING 0-2800Select this setting to eliminate vertical wide stripes, if they appear, when 
you are viewing projected images.
COMPUTER INPUTAUTO Automatically sets the appropriate setting.
RGBSelect this setting when you connect the projector to high definition 
video equipment having R, G, and B output terminals.
YC
BCR/YPBPRSelect this setting when you connect the projector to a DVD player or 
other device having Y, CB, and CR (or Y, PB, and PR) component video 
output terminals.
OVER SCAN 100%-90% Use this setting to adjust the display area of projected images.
HOLD OFF / ON
 Use this setting to adjust projected images when flagging occurs in the 
upper area of the screen.
USER OK
 
CLAMP POSITION 1-255Use this setting to correct solid white or solid black that appears in pro-
jected images.
CLAMP WIDTH 1-63 Use this setting to correct solid black that appears in projected images.
VERT.SYNC AUTO / OFFUse this setting to adjust projected images when the motion is not 
smooth. Select AUTO for most cases.
LPF ON / OFF Select this setting to enable or disable LPF.
SHUTTER(U) 0-20Use this setting to adjust projected images when noise appears in the 
top part of the image.
SHUTTER(L) 0-20Use this setting to adjust projected images when noise appears in the 
bottom part of the image.
SHUTTER(LS) 0-20Use this setting to adjust projected images when noise appears in the 
left half of the image.
SHUTTER(RS) 0-20Use this setting to adjust projected images when noise appears in the 
right half of the image.
Menu option Setting Feature description
NETWORK IP CONFIG 
menu
PROJECTOR NAME*****
...Displays PROJECTOR NAME. Displays PROJECTOR NAME in 
blank when PROJECTOR NAME is not set.
SET
 Set PROJECTOR NAME. Enter up to 15 characters (alphabets or 
numeric characters).
NETWORK PASSWORD OK
 Set the password for Web control or PJLink certification.
IP CONFIG OK Select this setting for IP Configuration.
DHCP ON  / OFF Use this setting when you obtain IP CONFIG automatically by 
DHCP server.
IP ADDRESS***,***,***,***Displays IP ADDRESS. However, IP ADDRESS is not set as factory 
default, and cannot be displayed.
SET
 Set IP ADDRESS. When DHCP is set to ON, you cannot change 
this setting.
SUBNET MASK***,***,***,***Displays SUBNET MASK. However, SUBNET MASK is not set as 
factory default, and cannot be displayed.
SET
 Set SUBNET MASK. When DHCP is set to ON, you cannot change 
this setting.
DEFAULT GATEWAY***,***,***,***Displays DEFAULT GATEWAY. However, DEFAULT GATEWAY is 
not set as factory default, and cannot be displayed.
SET
 Set DEFAULT GATEWAY. When DHCP is set to ON, you cannot 
change this setting.
MAC ADDRESS xx-xx-xx-xx-xx-xx Displays MAC ADDRESS.
PJLink CERTIFICATION ON   / OFF  Use this setting for PJLink Certification.
NETWORK RESET OK  Resets the Network Setting.
USEROKOFFHOLD100%
OVER SCAN
SIGNAL
R G BR G B
HORIZ. POSITION 0
VERT. POSITION 0
TRACKING 0
COMPUTER
INPUT RGB FINE SYNC. 0
opt.
SIGNALUSERCLAMP
POSITION1
CLAMP WIDTH 1
LPF OFF
SHUTTER(U) VERT. SYNC. AUTO
0
?
SHUTTER(L)
0SHUTTER(LS)
0SHUTTER(RS)
0
opt.
opt.
NETWORKPROJECTOR 
NAME
NETWORK
PASSWORD
PJLink
CERTIFICATION
OKSET
NETWORK RESETOK
IP CONFIGOKON
opt.
NETWORKIP CONFIGDHCP
IP ADDRESS
DEFAULT
GATEWAY
MAC ADDRESS
SUBNET MASK
xx-xx-xx-xx-xx-xx192.168.0.10
255.255.255.0
10.132.1.1
ON 
						

							EN-26
Menu operation (continued)
6. INFORMATION menu
Menu option Feature description
LAMP TIME (LOW)This menu shows a lamp operating time (hour) calculated assuming that LAMP MODE is LOW.
 When the LAMP MODE is STANDARD, this menu shows a longer lamp operating time than 
the actual time. (See page 36 for the interval of lamp replacement.)
 When the lamp operating time is 0 to 10 hours, 0H is displayed. When the lamp operating 
time exceeds 10 hours, the actual hours are displayed.
 When the lamp operating time reaches 3750 hours, the bar turns yellow. When it reaches 
4750 hours, the bar turns red.
(The lamp lifetime is 5000 hours.)
INPUT Indicates the name of the terminal to which the currently projected video signal is being input.
RESOLUTION Indicates the resolution of the currently projected video signal.
VERTICAL FREQUENCY Indicates the vertical frequency of the currently projected video signal.
HORIZONTAL FRE-
QUENCYIndicates the horizontal frequency of the currently projected video signal.
SYNC. TYPE Indicates the type of the sync signal for the currently projected video signal.
LAMP TIME (LOW)
INPUT
RESOLUTIONVERTICAL
FREQUENCY
HORIZONTAL
FREQUENCY
SYNC. TYPE 5wire60.02 KHz75.04 Hz 1024x768 COMPUTER20 HRGB
HV
INFORMATION
opt. 
						

							EN-27
ENGLISH
Image adjustment
Adjusting projected images
To adjust the brightness (CONTRAST and BRIGHT-
NESS):
You can make adjustments of the brightness of the projected image 
using the menu.
(See page 20 or 22 for the menu options.)
1. Display the QUICK MENU or the IMAGE menu.
2. Select CONTRAST or BRIGHTNESS by pressing the S or T 
button.
3. Adjust the selected option by pressing the W or X button.
To cancel the menu:
4. Press the MENU button.
CONTRASTSelect to adjust the contrast of the image. Every time the X button is 
pressed, the image becomes brighter and more clearly defined. Every 
time the W button is pressed, the image becomes darker and less 
clearly defined.
BRIGHTNESSEvery time the X button is pressed, the image becomes brighter. 
Every time the W button is pressed, the image becomes darker.
To adjust the color (COLOR and TINT):You can adjust the color of the projected image using the menu.
(See page 22 for the menu options.)
1. Display the IMAGE menu.
2. Select COLOR or TINT by pressing the S or T button.
 COLOR and TINT is selectable only when the input signal is 
VIDEO.
 TINT is selectable only when the NTSC or 4.43NTSC signal 
is input.
3. Adjust the selected option by pressing the W or X button.
To cancel the menu:
4. Press the MENU button.
COLORUse to adjust the color density of the projected image. Every time the 
X button is pressed, the color becomes darker. Every time the W but-
ton is pressed, the color becomes lighter.
TINTUse to adjust the tint of the projected image. Every time the X button 
is pressed, the image appears more greenish. Every time the W but-
ton is pressed, the image appears more reddish.
To sharpen or soften the projected image (SHARPNESS):You can adjust the sharpness of the projected image using the menu.
(See page 20 or 22 for the menu options.)
1. Display the QUICK MENU or the IMAGE menu.
2. Select SHARPNESS by pressing the S or T button.
3. Adjust the selected option by pressing the W or X button.
To cancel the menu:
4. Press the MENU button.
To adjust the tone of white (COLOR TEMP.):You can select a preset color temperature (white tone) using the 
menu.
(See page 20 or 22 for the menu options.)
1. Display the QUICK MENU or the IMAGE menu.
2. Select COLOR TEMP. by pressing the S or T button.
3. Select your desired color temperature by pressing the W or X 
button.
To cancel the menu:
4. Press the MENU button.
To adjust the tone of white (To customize the color tem-
perature):
To set (and store) a user-defined color temperature, perform the fol-
lowing procedure.
(See page 22 for the menu options.)
1. Select COLOR TEMP. in the IMAGE menu.2. Press the W or X button to select USER  .
3. Press the ENTER button.
4. Press the S or T button to select the desired setting.
5. Press the W or X button to adjust the selected setting.
6. Repeat steps 4 and 5 for optimal adjustment results.
To cancel the menu:
7. Press the MENU button.
To enable the stored color temperature:
1. Set COLOR TEMP. to USER   in the IMAGE menu.
About color temperatureThere are different variations in white color. Color temperature is a 
way to show these variations in white. When the temperature is 
low, white appears reddish. When the temperature rises, white 
appears bluish. For example, you can change the temperature 
using the following procedures.
To raise the temperature: Increase CONTRAST B (blue) and 
decrease CONTRAST R (red).
To reduce the temperature: Decrease CONTRAST B (blue) and 
increase CONTRAST R (red).
 If you set CONTRAST R, G, and B to negative values, the 
brightness of the image cant retain the original even when you 
maximize the value of CONTRAST in the QUICK MENU or the 
IMAGE menu.
Color EnhancerYou can set user-defined values for the brightness and hue using the 
menu. (See page 22 for the menu options.)
1. Display the IMAGE menu.
2. Select COLOR ENHANCER by pressing the S or T button.
3. Select USER   by pressing the W or X button.
4. Press the ENTER button.
5. Select a setting you want to set.
GAMMA modeUse this setting to set an optimal gamma value and modulation of 
lamp power. The level of brightness can be adjusted for subdued 
colors.
DYNAMIC ............Select when viewing crisp, clear images in a 
brightly lit room or strong daylight.
The level of brightness is adjusted to higher levels.
NATURAL ............Select when viewing images of which colors are 
more faithfully reproduced. 
The level of brightness and vividness is adjusted 
to optimal levels.
DETAIL ................Select when viewing images of which brightness 
should be kept relatively low, such as movies 
and music video clips.
CONTRAST B 0BRIGHTNESS R 0
CONTRAST RCOLOR TEMP.-USER0CONTRAST G 0
BRIGHTNESS G 0BRIGHTNESS B 0
AUTO COLOR
ENHANCER
COLOR ENHANCER-USER
BrilliantColorTM10RGB-COLOR0RGB-TINT0
GAMMA MODE DYNAMIC 
						

							EN-28
Image adjustment (continued)
BrilliantColorTM
Use this setting to make colors with medium brightness, such as yel-
low and the skin tone appear natural. Press the W button to decrease 
the value to lessen the effect. Press the X button to increase the value 
to heighten the effect. (BrilliantColor
TM has no effect at value 0.)
6. Select a value by pressing the W or X button.
 For more enhanced color reproduction, set BrilliantColor
TM 
to 0. The white area of the color wheel is disabled, and you 
can reproduce true-color images.
RGB-COLORUse to adjust the color intensity of the projected image. Every time the 
X button is pressed, the color becomes thicker. Every time the W but-
ton is pressed, the color becomes lighter.
RGB-TINTUse to adjust the color balance of the projected image. Every time the 
X button is pressed, the image appears more greenish. Every time 
the W button is pressed, the image appears more reddish.
This projector automatically and properly projects video signals being 
input from the computer. However, some video signals may not be 
projected, depending on the type of the computer. When it occurs, 
press the AUTO POSITION button. (See page 17.) When the signal is 
still not projected properly, adjust the projected image using the SIG-
NAL menu.
How to adjust the image supplied from the computer 
using the menu:
Perform the following procedures when the following conditions occur.
When wide strips appear
................. adjust TRACKING in the SIGNAL menu.
When the projected image flickers
When the projected image is blurred
................. adjust FINE SYNC. in the SIGNAL menu.
When the projected image is displaced horizontally
................. adjust HORIZ.POSITION in the SIGNAL 
menu. Every time the W button is pressed, 
the image moves to the right. Every time the 
X button is pressed, the image moves to the 
left.
When the projected image is displaced vertically
................. adjust VERT.POSITION in the SIGNAL 
menu. Every time the W button is pressed, 
the image moves down. 
Every time the X button is pressed, the 
image moves up.
When the top part of the image flags
................. change the setting of HOLD in the SIGNAL 
menu. To select ON  , press the ENTER 
button, and adjust BEGIN or END to mini-
mize the flagging.
A solid black or solid white appears in the image
................. adjust CLAMP POSITION or CLAMP 
WIDTH in the SIGNAL - USER menu.
When the motion is not smooth.
................. adjust VERT. SYNC in the SIGNAL - USER 
menu. 
Select AUTO for most cases.
Noise appears in the right or left half of the image.
................. adjust SHUTTER(LS) or SHUTTER(RS) in 
the SIGNAL - USER menu.
Noise appears in the top or bottom part of the image.
................. adjust SHUTTER(U) or SHUTTER(L) in the 
SIGNAL - USER menu.
1. Display the SIGNAL menu.
2. Press the S or T button to select a setting to adjust.
3. Adjust the selected setting by pressing the W or X button.
To cancel the menu:
4. Press the MENU button.
 Do not change the settings of the SIGNAL menu for ordinary 
use.
Simple method to adjust the image position
To adjust the horizontal position:
1. Align the left edge of the image with the left side of the 
screen by adjusting HORIZ.POSITION. Then, align the right 
edge of the image with the right side of the screen by adjust-
ing TRACKING.
2. Repeat step 1 to complete the adjustment of the horizontal 
position.
To adjust the vertical position:
3. Align the upper edge of the image with the upper side of the 
screen by adjusting VERT.POSITION.
LPF (Progressive filter)You can select to enable or disable the LPF. This option is set to OFF 
normally.
Vertical or horizontal streaks may appear in the projected image, 
depending on the type of the DVD player, game console or computer 
in use. If this occurs, reduce noise by enabling the LPF. Projected 
images appear slightly faint. 
						

							EN-29
ENGLISH
Network settings
You can set the network of the projector using the menu.
Setting Projector Name1. Display the NETWORK menu. (See page 22 for menu setting.)
2. Press the S or T button to select PROJECTOR NAME.
3. Press the W or X button to select SET   .
4. Press the ENTER button.
 PROJECTOR NAME screen appears.
5. Press the direction buttons to move the key cursor, select the 
characters or marks to enter, and press the ENTER button.
 Projector Name can be set using up to 15 characters includ-
ing alphabets (capital/small), numeric characters, or marks.
← key: Shifting the position of enter cursor to the 
left for each character.
→ key: Shifting the position of enter cursor to the 
right for each character.
DEL key: Deleting the character in the position of 
enter cursor for each character.
caps/CAPS key: Switching an alphabet character to CAPI-
TAL or small.
NEXT/PREV key:Switching the marks listed on the fourth 
line.
SPACE key: Inserting a space in the position of enter 
cursor.
CLEAR key: Deleting all the entered characters.
6. When selecting OK, the setting is completed as the name 
stored. However, when selecting CANCEL, the setting is com-
pleted without storing.
 The display returns the NETWORK menu after selecting OK 
or CANCEL.
 It may take some time to reflect the settings.
Network Password Settings1. Display the NETWORK menu. (See page 22 for menu setting.)
2. Press the S or T button to select NETWORK PASSWORD.
3. Press the ENTER button.
 CURRENT NETWORK PASSWORD screen appears.4. Press the direction buttons to move the key cursor, select the 
characters or marks to enter, and press the ENTER button.
 Password can be set using up to 32 characters including 
alphabets (capital/small) or numeric characters.
← key: Shifting the position of enter cursor to the 
left for each character.
→ key: Shifting the position of enter cursor to the 
right for each character.
DEL key: Deleting the character in the position of 
enter cursor for each character.
caps/CAPS key: Switching an alphabet character to CAPI-
TAL or small.
CLEAR key: Deleting all the entered characters.
 The default password is admin.
5. Select OK, and NEW NETWORK PASSWORD screen appears 
if the entered password is correct.
 If the entered password is not correct, CURRENT NET-
WORK PASSWORD screen appears again.
6. Enter the NEW NETWORK PASSWORD and CONFIRM NET-
WORK PASSWORD.
 Password can be set using up to 32 characters including 
alphabets (capital/small) or numeric characters.
← key: Shifting the position of enter cursor to the 
left for each character.
→ key: Shifting the position of enter cursor to the 
right for each character.
 key: Shifting the position of enter cursor 
between NEW NETWORK PASSWORD 
and CONFIRM NETWORK PASSWORD.
DEL key: Deleting the character in the position of 
enter cursor for each character.
caps/CAPS key: Switching an alphabet character to CAPI-
TAL or small.
CLEAR key: Deleting all the entered characters.
7. When NEW NETWORK PASSWORD and CONFIRM NET-
WORK PASSWORD are matched, the setting is completed after 
changing the NETWORK PASSWORD.
 If the entered content is not matched, NEW NETWORK 
PASSWORD screen appears again after an error dialog is 
displayed.
 It may take some time to reflect the settings.IP Settings1. Display the NETWORK menu. (See page 22 for menu setting.)
2. Press the S or T button to select IP CONFIG.
3. Press the ENTER button.
 IP CONFIG menu appears.
opt.
NETWORKPROJECTOR 
NAME
NETWORK
PASSWORD
PJLink
CERTIFICATION
OKSET
NETWORK RESETOK
IP CONFIGOKON
PROJECTOR 
NAMESET
CODE : XD600       v z ?%
NETWORK
PASSWORDOK
↔
IP CONFIGOK
IP CONFIGDHCP
IP ADDRESS
DEFAULT
GATEWAY
MAC ADDRESS SUBNET MASK
xx-xx-xx-xx-xx-xx192.168.0.10
255.255.255.0
10.132.1.1ON 
						

							EN-30
Network settings (continued)
Setting or Clearing DHCP1. Display the IP CONFIG menu.
2. Press the S or T button to select DHCP.
3. Press the ENTER button.
 Confirmation dialog appears.
4. Press the W or X button to select ON   or OFF   . 
5. Select the item to set, and press the ENTER button.
 To cancel the setting, press the MENU button.
 It may take some time to reflect the settings.
 When setting DHCP to ON, IP ADDRESS, SUBNET MASK, 
and DEFAULT GATEWAY cannot be set. If you set those set-
tings, set DHCP to OFF and perform the IP settings as the 
following procedures.
IP Address Settings1. Display the IP CONFIG menu.
2. Press the S or T button to select IP ADDRESS.
3. Press the W or X button to select SET   .
4. Press the ENTER button.
 IP ADDRESS screen appears.
5. Press the direction buttons to move the key cursor, select the 
numbers to enter, and press the ENTER button.
 Set the numeric value within the range from 0 to 255. How-
ever, set the numeric value for the final octet within the range 
from 1 to 254.
← key: Shifting the position of enter cursor to the left.
→ key: Shifting the position of enter cursor to the right.
DEL key:Deleting the character in the position of enter cur-
sor for each character.
6. When selecting OK, the setting is completed as the IP 
ADDRESS stored. However, when selecting CANCEL, the set-
ting is completed without storing.
 If the entered content is not correct, IP ADDRESS screen 
appears again after an error dialog is displayed.
 It may take some time to reflect the settings.
Subnet Mask Settings1. Display the IP CONFIG menu.
2. Press the S or T button to select SUBNET MASK.
3. Press the W or X button to select SET   .
4. Press the ENTER button.
 SUBNET MASK screen appears.
5. Enter the Subnet Mask.
 Refer to IP Address Settings for the detail of entering.6. When selecting OK, the setting is completed as the Subnet 
Mask stored. However, when selecting CANCEL, the setting is 
completed without storing.
 If the entered content is not correct, SUBNET MASK screen 
appears again after an error dialog is displayed.
 It may take some time to reflect the settings.
Default Gateway Settings1. Display the IP CONFIG menu.
2. Press the S or T button to select DEFAULT GATEWAY.
3. Press the W or X button to select SET   .
4. Press the ENTER button.
 DEFAULT GATEWAY screen appears.
5. Enter the Default Gateway.
 Refer to IP Address Settings for the detail of entering.
6. When selecting OK, the setting is completed as the Default 
Gateway stored. However, when selecting CANCEL, the setting 
is completed without storing.
 If the entered content is not correct, DEFAULT GATEWAY 
screen appears again after an error dialog is displayed.
 It may take some time to reflect the settings.
Setting or Clearing PJLink CertificationPerform the settings to start PJLink protocol communication.
 See page 34 for the detail of PJLink.
1. Display the NETWORK menu. (See page 22 for menu setting.)
2. Press the S or T button to select PJLink CERTIFICATION.
3. Press the ENTER button.
 Confirmation dialog appears.
4. Press the W or X button to select ON   or OFF   . 
5. Select the item to set, and press the ENTER button.
 To cancel the setting, press the MENU button.
 It may take some time to reflect the settings.
Initialization of Network Settings1. Display the NETWORK menu. (See page 22 for menu setting.)
2. Press the S or T button to select NETWORK RESET.
3. Press the ENTER button.
 Confirmation dialog appears.
4. If pressing the ENTER button again, the Network Settings can 
be initialized.
 It may take some time to reflect the settings.
DHCPON
IP ADDRESSSET
SUBNET MASKSET
DEFAULT
GATEWAYSET
PJLink
CERTIFICATIONON
NETWORK RESETOK