Mitsubishi Tx10u Projector User Manual

							EN-51
Before asking for repair of the projector, check the following. If the symptom persists, stop using the projector, be sure 
to unplug the power plug, and then contact your dealer.
No image appears on the screen.
ProblemSolution
Power can not be turned 
on.• Check whether the indicators are on or off and how they are lightning.
No image appears on the 
screen.• Cancel the AV mute by pressing the AV MUTE button.
• It may take about 1 minute for the lamp to light up.
• The lamp fails to light up on rare occasions. In such a case, wait for a few minutes 
and then try again.
• If the projector was turned off before the lamp was cooled down sufficiently last 
time, the fan may start rotating and the POWER button may not work after the 
power cord is plugged. Press the POWER button to turn back on the POWER 
indicator.
• Check that the intake vent is clean.
• Check that the lamp cover is closed. (See page 48 or 57.)
• Check that the cables connected to the external devices are not broken.
• When an extension cable is being used, replace it with the supplied cable for check.
When images are displayed correctly, add an RGB signal amplifier to the extension 
cable.
POWER STATUS Solution
• Connect the power cord to the projector.
• Plug the power cord into a wal outlet.
• If any objects are blocking the air inlet or outlet 
grille, remove them and carry out the following.
1. Unplug the power cord from the wall outlet.
2. Make sure that the projector has cooled off.
3. Plug the power cord into the wall outlet.
4. Press the POWER button.
• If any objects are blocking the air inlet or outlet 
grille, remove them.
• Don’t expose the air outlet grilles to hot air 
emitted from a heating appliance.
• After the STATUS indicator stops blinking, 
press the POWER button.
• If you unplug the power cord while the fan is
rotating, the lamp may not turn on about 1
minute when you plug the power cord next
time.
• The lamp can’t turn on again for 1 minute
after it goes out.
• Press the POWER button several times.
• Replace the lamp. (The lamp is at the end of its 
life.)
• Attach the lamp cover on the top.
• Unplug the power cord from the wall outlet 
and contact your dealer.
OffOff
Stea dy re d
Off
Blinking orange
Blinking green
Ste a dy re d
Blinking 
red/green
Off
Steady
Or
Blinking
Troubleshooting 
						

							EN-52
Troubleshooting (continued)
No image appears on the screen. (continued)
Images are not displayed correctly. 
ProblemSolution
Power turns off. • This problem may occur when the intake vent and/or exhaust vents are blocked. (In 
such a case, the STATUS indicator brinks orange.)
JRemove the objects blocking the intake vent and/or exhaust vents and then 
carry out the following procedure.
1. Wait for the intake fan and/or exhaust fan to stop. (Wait until the STATUS 
indicator goes out.)
2. Unplug the power cord from the wall outlet.
3. Wait about 10 minutes.
4. Plug the power cord into the wall outlet.
5. Press the POWER button.
• When the STATUS indicator is steady red, it is indicating that the lamp should be 
replaced. Replace the lamp in this case.
• Check that AUTO POWER OFF in the INSTALLATION menu has been set to OFF.
• If the lamp has deteriorated, it may go out after a while it illuminates.
The screen for entering 
the password appears.• PASSWORD FUNCTION in the FEATURE menu has been set to DISPLAY INPUT     
to enable the password lock.
JEnter the password or contact the person in charge of management of the 
projector. (See page 43.)
“NO SIGNAL” is 
displayed.• Turn on the power of the connected device, or check whether there is something 
wrong with the connected device.
• Check whether the external device output signals. (Check this especially when the 
external device is a laptop computer.)
• Check that the cable connected to the external device isn’t defective.
• Check that the projector is connected to the external device using the correct 
terminals.
• Check that the connected device is correctly selected as the input source.
• When an extension cord is being used, replace it with the supplied cable and check 
whether images are projected correctly. If images are projected correctly, use an 
RGB signal amplifier along with the extension cord.
ProblemSolution
Projected images are 
shaking.
Projected images are 
displaced. • Check that the cable connected to the external device isn’t intermittent.
• Connect the cable’s plug with the external device’s connector firmly.
• Project an image containing a lot of characters without black areas and press the 
AUTO POSITION button.
• Some computers output out-of-spec signals on rare occasion. In such a case, 
change the setting of the SIGNAL DETECT in the FEATURE menu and press the 
AUTO POSITION button. If the position (and size) of the projected images is still 
incorrect, make adjustment using the SIGNAL menu. (For details, see flowchart on 
page 37.)
Projected images are 
distorted. • Adjust the projector and the screen so that they are perpendicular to each other. 
(See page 17.)
• Use the flat screen.
Projected images are 
dark. • Adjust BRIGHTNESS and CONTRAST in the IMAGE menu. (See page 26.)
• 3D images displayed on the projector appear darker. It is normal and does not 
mean the projector is malfunctioning.
• When viewing 2D images, set 3D FORMAT to AUTO   (for HDMI input only) or set 
3D in the IMAGE menu to OFF. (When AUTO is selected, only 3D images become 
darker.)
• Replace the lamp. (See page 48.) 
						

							EN-53
Images are not displayed correctly. (continued) 
ProblemSolution
Projected images are 
blurred.• Adjust the focus. (See page 19.)
• Clean the lens.
• Press the W or X button on the remote control to eliminate flicker.
• Adjust TRACKING and FINE SYNC. in the SIGNAL menu. (See page 30.)
• Set OVER SCAN in the SIGNAL menu to 100%. (See page 30.)
• Set the keystone adjustment to 0 using the KEYSTONE button. (See page 17.)
• Set the projected image size to maximum (0) in E-Zoom function.(See page 12.)
• Adjust BRIGHTNESS and CONTRAST in the IMAGE menu. (See page 26.)
• Adjust the projector and the screen so that they are perpendicular to each other. 
(See page 17.)
Afterimages persist on 
the screen.• This phenomenon is improved by keeping projecting an evenly bright image. (Such 
“image burn-in” phenomenon where afterimages persist on the screen may occur if 
a stationary image is kept displayed on the screen for a long time.)
White dots are seen on 
projected images. Black 
dots are seen on 
projected images. • This phenomenon is normal for a DLP™ projector and is not a malfunction. (A very 
small number of pixels may visibly or invisibly be persistent all the time, but they are 
not a sign of system malfunctions. Over 99.99% of the pixels are effective.)
Fine streaks are seen on 
projected images.• This is due to interference with the screen surface and is not a malfunction. Replace 
the screen or displace the focus a little.
• Vertical or horizontal streak noise may appear on the projected image, depending 
on the type of the DVD player, game console or computer you use. In such a case, 
you can reduce such streak noise by enabling the LPF.
Projected images 
become wavy. • Connect the plugs of the cables to external devices securely.
• Keep the projector away from equipment generating interfering radio waves.
• When the keystone adjustment is carried out, the image may not be displayed 
correctly because of the type of input signal. This isn’t a product malfunction. In this 
case, readjust the keystone so that the amount of keystone correction is as small as 
possible.
Hue is not appropriate.  • Check that the cables connected to the external devices are not broken.
Tint in projected images 
is incorrect.• If the setting of COMPUTER INPUT in the SIGNAL menu is inconsistent with the 
RGB/Y
CBCR output setting of the external device even when the input source is 
other than computer (for example, when the input source is HDMI), the entire image 
appears reddish or greenish.
• Check that COMPUTER INPUT in the SIGNAL menu is correctly set. (See page 30.)
• Check that the cable connected to the external device isn’t broken.
Different color tint. • When comparing images projected by two projectors, tints in the displayed images 
may be different because of variation between their optical components. This is not 
a malfunction.
• When comparing the image projected by this projector with those displayed on the 
television or PC monitor, tints in the displayed images may be different because of 
difference in the range of color reproducibility. This is not a malfunction.
Only the motion areas in 
the images supplied from 
the computer aren’t 
displayed.• This is caused by the computer being used. Contact the manufacturer of your 
computer. 
						

							EN-54
Images are not displayed correctly. (continued) 
Others
ProblemSolution
Projected images are 
obscured.• Match the output resolution of your computer with the resolution of the projector. 
For the method to change the output resolution of the computer, contact the 
manufacturer of your computer. (See page 60.)
• Some images and texts appear obscured during the keystone adjustment. In such 
cases, use the projector without applying the keystone adjustment. (See page 17.)
Noise appears around the 
image.• In some images such as DVD, noise may appear around the recorded image. In this 
case, decrease the setting value of OVER SCAN of the SIGNAL menu. (See page 
30.)
Projected images are 
flickering.• After the POWER button or ON button on the remote has been pressed, or the 
LAMP MODE setting has changed, images may be flickering until the lamp lights 
stably. This is an expected behavior.
• When selecting the input signal, AUTO POSITION, and Image, the projected image 
may be flickering temporarily. This is not a product malfunction.
Projector images are 
twitching.• Projector may be vibrating. Set AUTO KEYSTONE to OFF or lower the VOLUME T 
button of the Remote control.
ProblemSolution
The exhaust vents emit 
warm air.• This air comes out after cooling the inside of the projector. You may feel hot, but this 
vis not a malfunction. 
No audio is output. • Check that the volume isn’t set to low.
• When the external device is connected with an HDMI cable, set the audio output of 
the device to PCM output.
The menu can’t be used.  • The microcomputers inside the projector may be wrongly operating because of 
noise. 
JPress the POWER button to turn off the lamp and unplug the power cord from 
the wall outlet. Wait about 10 minutes, plug the power cord in, and try again.
“TEMPERATURE!!” is 
displayed.• This indication appears when the ambient temperature rises high. When the 
ambient temperature stays high, the lamp goes out.
JEliminate any causes of the rise in the ambient temperature.
• This indication appears when the air inlet or outlet grille is blocked. When they are 
kept blocked, the lamp goes out. 
JRemove the objects blocking the air inlet or outlet grille.
The  mark appears. • This mark appears when ineffective operation is carried out. This isn’t a product 
malfunction.
The remote control 
doesn’t function easily or 
at all.• Check that the batteries are loaded in the remote control or the batteries are not 
weak. (See page 9.)
• Check that the remote control sensor isn’t exposed to direct sunlight or fluorescent 
light. (See page 9.)
• Use the remote control within its operation range. (See page 9.)
• Use the remote control at least 10 cm away from the projector.
The fans sound during 
standby.• When STANDBY MODE is set to STANDARD, the fans rotate at very low speed 
during standby after plugging the power cord (with 5 second high speed rotation at 
the beginning) and after turning off the lamp. This is to cool down the projector 
operating various functions during standby and is not a malfunction. 
						

							EN-55
Others (continued)
If the following problem occurs after the lamp is replaced, check the following first.
ProblemSolution
Abnormal sound is heard.  • Because the color wheel spins at a high speed, metallic sounds may be heard in 
rare occasions. Such symptom is not a malfunction.
Images are not 3D. 
* Use commercially 
available 3D glasses 
supporting the DLP™ 
Link™ system. No 3D 
glasses are supplied with 
the projector.• Is the 3D mode of the projector set properly for the image?
JSet 3D FORMAT in the 3D menu of the projector properly for the image (AUTO 
, SIDE BY SIDE  , TOP AND BOTTOM  , or FRAME SEQUENTIAL  ).
• View 3D image from the front of the screen. At the angle to the screen, you may not 
be able to view proper 3D images. 
• Is there any obstacle between the 3D glasses and the screen? Or, is there any 
sticker or label over the sensor of the 3D glasses?
JThe 3D glasses work by receiving signals of the images being viewed. Check 
that there is no obstacle between the 3D glasses and the screen.
• Are you viewing images from a very close distance?
JViewing images from a very close distance may not obtain the 3D effect. View 
images from a proper distance.
• The 3D glasses may become out of sync due to fluorescent light. Turn off the 
fluorescent light. 
• Are the 3D glasses turned off?
J Turn on the 3D glasses.
• The signals listed in the table on page 61 can be displayed in 3D format. You cannot 
view other signals in 3D format even when you set 3D FORMAT in the 3D menu to 
AUTO  , SIDE BY SIDE  , TOP AND BOTTOM  , or FRAME SEQUENTIAL  .
• You may not obtain the 3D effect depending on the capabilities of your computer 
(including the graphic board, memory, and CPU).
• Some 3D glasses may not work with this projector. Ask the dealer for details.
There is something wrong 
with the 3D images.
* Use commercially 
available 3D glasses 
supporting the DLP™ 
Link™ system. No 3D 
glasses are supplied with 
the projector.• Depending on the 3D image status, you may feel something wrong with the 3D 
images.
JSwitch the 3D SYNC INVERT setting of the projector to check whether or not 
such feeling is eliminated.
• The 3D glasses may become out of sync due to fluoescent light. Turn off the 
fluorescent light.
• View 3D images from the front of the screen. At an angle to the screen, you may not 
be able to view proper 3D images.
The 3D glasses don’t turn 
on.
* Use commercially 
available 3D glasses 
supporting the DLP™ 
Link™ system. No 3D 
glasses are supplied with 
the projector.• Are the batteries of the 3D glasses still working?
JIf the 3D glasses don’t activate even when you turn on the power switch, replace 
or charge the batteries of the 3D glasses. For details, see the user manual of the 
3D glasses.
ProblemSolution
The projector does not 
turn on.• Fit the lamp cover securely. (See pages 48 or 49.)
• Reset the lamp operating time. (See page 49.)
The STATUS indicator 
blinks.• Reset the lamp operating time. (See page 49.) 
						

							EN-56
Maintenance
Warning:
Do not use flammable solvents (benzene, thinner, etc.) and flammable aerosols when cleaning the projector body and 
lens. Flammable substances may ignite causing fire or breakdown while the lamp is illuminating.
Caution:
Be sure to turn off the lamp and unplug the power cord from the wall outlet before you perform any maintenance on 
the projector.
Cleaning of the projector and the ventilation slots
Use a soft cloth to clean the projector and the ventilation grilles. When the grilles become dirty, wipe them with a soft 
cloth dampened with diluted mild detergent, and then wipe them with a dry cloth.
To protect the surface of the projector from fading or deteriorating:
• Do not spray insecticide on or inside the projector.
• Do not use benzin or thinner to clean it.
• Do not let rubber or plastic materials contact with projector.
Cleaning of the lens
Use a standard lens-cleaning brush or a piece of lens tissue dampened with lens cleaning fluid. The lens surface is 
fragile. Use only recommended, nonabrasive lens-cleaning materials. Do not touch the lens with your fingers.
Kensington Lock
This projector has a Kensington Security Standard connector for use with Kensington MicroSaver Security System. 
Refer to the information that came with the Kensington System for instructions on how to use it to secure the 
projector. Please contact Kensington Technology Group below.
Kensington Technology Group
2855 Campus Drive
San Mateo, CA 94403, U.S.A.
Phone: +1- (650)572-2700Fax: +1- (650)572-9675
This projector has two indicators, each of which shows the operation condition of the projector.
The following offer solutions to possible problems. If these problem persist, turn the projector off and consult your 
dealer. 
						

							EN-57
This projector has two indicators, each of which shows the operation condition of the projector. The following offer 
solutions to possible problems. If these problem persist, turn the projector off and consult your dealer.
Normal condition
Abnormal condition
POWERSTATUSCONDITIONNOTE
Stand-by
Lamp stand-by for power-off The power cannot be turned on by 
pressing the POWER button.
Lamp stand-by for power-on The power cannot be turned off by 
pressing the POWER button.
The power is on. (Normal condition)
POWERSTATUSCONDITIONPOSSIBLE SOLUTION
Abnormal temperature
• The ventilation grilles is clogged with dust or 
dirt.
• The room temperature is high.• Clean the ventilation grilles.
• Relocate the projector to a cooler 
place.
The protection circuit is working or the lamp is in 
an abnormal condition.• Wait until the STATUS indicator goes 
out, then press the POWER button.
• If the above solution is not effective, 
replace the lamp.
The lamp operation time exceeds the time 
elapsed until the lamp lifetime notice while the 
power is on. (See page 49.)Replace the lamp.
Change with a new lamp if this problem 
recurs.
The lamp operation time exceeds the time 
elapsed until the lamp lifetime notice while the 
power is off. (See page 49.)
The lamp operation time exceeds the time 
elapsed until the lamp lifetime. (See page 49.)
The lamp cover isn’t closed. Close the cover correctly.
Abnormal. Contact your dealer.
STATUS indicator POWER indicator
Steady red
Off
Blinking green
Steady green
Blinking green
Steady green
Steady green
Or
Steady red
Blinking orange
Steady redBlinking green
Steady greenBlinking green/red
Steady redBlinking red
Steady redSteady red
Blinking green/redOff
Blinking green/red
Steady
Or
Blinking 
						

							EN-58
• The specifications and outside appearance of the projector are subject to change without prior notice.
Connectors
Type DLP™ projector
Model TX10U TW11U
Rated power supply 100 - 240 V AC, 50/60 Hz
Power consumption 3.0 A
During standby: 0.5W (when Standby Mode is Low)
Display Technology 0.55-inch single chip Digital Micromirror 
Device (DMD)
Pixels: 1024 x 768 = 786432 pixels0.65-inch single chip Digital Micromirror 
Device (DMD)
Pixels: 1280 x 800 = 1024000 pixels
Colors 16770000 colors
Projection lens F 2.5 -2.8, f=18.4-22.0 mm F 2.6 -2.9, f=21.0-25.6 mm
Light source lamp 210 W
Picture size 40 - 300 inch (Wide) (aspect ratio 4:3) 40–300 inch (Wide) (aspect ratio 16:10)
PC compatibility Resolution:640 x 480 (Expand) - 
1024 x 768 (Real) - 
1600 x 1200 (Compress)
Sync on Green availableResolution:640 x 480 (Expand) - 
1280 x 800 (Real) - 
1600 x 1200 (Compress)
Sync on Green available
Video compatibility NTSC/NTSC 4.43/PAL (including PAL-M, N)/SECAM/PAL-60
Component Video (DVD/HDTV) (480i, 576i, 480p, 576p, 1080i, 720p, 1080p)
Speaker 10 W mono x 1
S-video input Luminance signal: 1.0 Vp-p 75 Ω  (negative sync.)
Chroma signal: 0.286 Vp-p 75 Ω  (burst signal)
Video input 1.0 Vp-p 75 Ω (negative sync.)
Audio input 350 mVrms, 10 kΩ or more
Analog RGB input RGB: 0.7 Vp-p 75 Ω  (negative sync.)
YP
BPR/YCBCR: 
Y: 1.0 Vp-p (negative sync.)
P
BPR/CBCR: 0.7 Vp-p
HD/CS: TTL level (positive or negative)
VD: TTL level (positive or negative)
HDMI input HDMI 19-pin
HDMI interface (TMDS single link) (only PCM audio is supported)
Control connector SERIAL terminal (RS-232C), LAN terminal (RJ-45)
Outside dimensions
(not including protrusion)319 x 103 x 224 mm (width x height x depth)
Weight Approx. 2.8 kg Approx. 2.8 kg
Length of power cord 71 inch (1.8 m)
Temperature, humidity
(performance guaranteed)+41°F (+5°C) - +95°F (+35°C), 30 - 90%
COMPUTER/COMPONENT VIDEO IN, MONITOR OUT 
(Mini D-SUB 15-pin)HDMI (HDMI 19-pin) SERIAL (D-SUB 9-pin)
15 11
610 15
191
2
1815
69
Specifications 
						

							Specifications (continued)
EN-59
Dimension drawing (unit: mm)
What’s included in the box
* One of power cords for the U.S., Europe, U.K., Australia, and South Korea is provided appropriately.
Replacement part (option/not included in the box)
Spare lamp: VLT-TX10LPAC power cord* for the U.S. J2552-0063-03 Remote control
for Europe J2552-0247-00 Safety Manual/Quick Start up
for the U.K. J2552-0065-02 CD-ROM
for Australia J2552-0053-00 Battery (2)
for South Korea J2552-0247-00
Computer cable J2552-0072-05
COMPUTER/COMPONENT 
VIDEO IN
Pin No. Spec.
1 R (RED)/C
R
2 G (GREEN)/Y
3B (BLUE)/C
B
4GND
5GND
6GND
7GND
8GND
9 DDC 5V
10 GND
11 GND
12 DDC Data
13 HD/CS
14 VD
15 DDC Clock
MONITOR OUT
Pin No. Spec.
1 R (RED)/C
R
2 G (GREEN)/Y
3B (BLUE)/C
B
4-
5GND
6GND
7GND
8GND
9-
10 GND
11 -
12 -
13 HD/CS
14 VD
15 -
Pin No. Spec.
1TMDS Data 2 +
2TMDS Data 2 
Shield
3TMDS Data 2 -
4TMDS Data 1 +
5TMDS Data 1 
Shield
6TMDS Data 1 -
7TMDS Data 0 +
8TMDS Data 0 
Shield
9TMDS Data 0 -
10 TMDS Clock +
11 TMDS Clock 
Shield
12 TMDS Clock -
13 CEC
14 -
15 SCL
16 SDA
17 DDC Ground
18 +5 V Power
19 Hot Plug DetectPin No. Name I/O
1- -
2TXDIN
3RXDOUT
4- -
5GND -
6- -
7- -
8- -
9- -
224
319
103 
						

							EN-60
Supported input signal
*1: Indicates the resolution when ASPECT in the FEATURE menu is set to NORMAL.
*3: Signals marked with O in the Plug and Play column are described in EDID (extended display identification data) of the projector. 
Signals described in the Signal mode column can be input regardless of the O mark in the Plug and Play column. For signals not 
marked with O in the Plug and Play column, the resolution may not be supported even when it is supported on the computer.
Signal modeResolution
(H x V)Horizontal 
frequency
(kHz)Vertical 
frequency
(Hz)Normal mode*1
TX10U
(H x V)Normal mode*1
TW11U
(H x V)Plug and Play*3
COMPUTER/
COMPONENT
VIDEO IN-1/2 terminalHDMI terminal
TV60, 480i (525i) 720 x 480 15.73 59.94 1024 x 768 1066 x 800
TV50, 576i (625i) 720 x 576 15.63 50.00 1024 x 768 1066 x 800
1080i60 (1125i60) 1920 x 1080 33.75 60.00 1024 x 576 1280 x 720 O
1080i50 (1125i50) 1920 x 1080 28.13 50.00 1024 x 576 1280 x 720 O
480p (525p) 720 x 480 31.47 59.94 1024 x 768 1066 x 800 O
576p (625p) 720 x 576 31.25 50.00 1024 x 768 1066 x 800 O
720p60 (750p60) 1280 x 720 45.00 60.00 1024 x 576 1280 x 720 O
720p50 (750p50) 1280 x 720 37.50 50.00 1024 x 576 1280 x 720 O
1080p60 (1125p60) 1920 x 1080 67.50 60.00 1024 x 576 1280 x 720 O
1080p50 (1125p50) 1920 x 1080 56.25 50.00 1024 x 576 1280 x 720 O
1080p24 (1125p24) 1920 x 1080 27.00 24.00 1024 x 576 1280 x 720 O
CGA84 640 x 400 37.86 84.13 1024 x 640 1280 x 800
CGA85 640 x 400 37.86 85.08 1024 x 640 1280 x 800
VGA60 640 x 480 31.47 59.94 1024 x 768 1066 x 800 O O
VGA72 640 x 480 37.86 72.81 1024 x 768 1066 x 800 O
VGA75 640 x 480 37.50 75.00 1024 x 768 1066 x 800 O
VGA85 640 x 480 43.27 85.01 1024 x 768 1066 x 800
SVGA56 800 x 600 35.16 56.25 1024 x 768 1066 x 800 O
SVGA60 800 x 600 37.88 60.32 1024 x 768 1066 x 800 O O
SVGA72 800 x 600 48.08 72.19 1024 x 768 1066 x 800 O
SVGA75 800 x 600 46.88 75.00 1024 x 768 1066 x 800 O
SVGA85 800 x 600 53.67 85.06 1024 x 768 1066 x 800
XGA60 1024 x 768 48.36 60.00 1024 x 768 1066 x 800 O O
XGA70 1024 x 768 56.48 70.07 1024 x 768 1066 x 800 O
XGA75 1024 x 768 60.02 75.03 1024 x 768 1066 x 800 O
XGA85 1024 x 768 68.68 85.00 1024 x 768 1066 x 800
XGA120 1024 x 768 97.55 119.99 1024 x 768 1066 x 800 O O
SXGA70a 1152 x 864 63.85 70.01 1024 x 768 1066 x 800
SXGA75a 1152 x 864 67.50 75.00 1024 x 768 1066 x 800
SXGA85a 1152 x 864 77.49 85.06 1024 x 768 1066 x 800 O
WXGA60 1280 x 768 47.77 59.87 1024 x 615 1280 x 768 O
WXGA60a 1280 x 800 49.70 59.81 1024 x 640 1280 x 800 O
WXGA60b 1360 x 768 47.71 60.01 1024 x 579 1280 x 724
WXGA60c 1366 x 768 47.71 59.79 1024 x 576 1280 x 720 O O
WXGA+60 1440 x 900 55.94 59.89 1024 x 640 1280 x 800 O O
WXGA120a 1280 x 800 101.56 119.91 1024 x 640 1280 x 800 O O
SXGA60b 1280 x 960 60.00 60.00 1024 x 768 1066 x 800 O
SXGA75b 1280 x 960 75.00 75.00 1024 x 768 1066 x 800 O
SXGA85b 1280 x 960 85.94 85.00 1024 x 768 1066 x 800
SXGA60 1280 x 1024 63.98 60.02 960 x 768 1000 x 800 O
SXGA75 1280 x 1024 79.98 75.02 960 x 768 1000 x 800 O
SXGA85 1280 x 1024 91.15 85.02 960 x 768 1000 x 800
SXGA+60 1400 x 1050 65.32 59.98 1024 x 768 1066 x 800 O O
SXGA+75 1400 x 1050 82.28 74.87 1024 x 768 1066 x 800
MAC13 640 x 480 35.00 66.67 1024 x 768 1066 x 800 O
MAC16 832 x 624 49.72 74.55 1024 x 768 1066 x 800
MAC19 1024 x 768 60.24 75.02 1024 x 768 1066 x 800
HP75 1024 x 768 62.94 74.92 1024 x 768 1066 x 800
SUN66a 1152 x 900 61.85 66.00 984 x 768 1024 x 800
SUN76a 1152 x 900 71.81 76.64 984 x 768 1024 x 800
SUN66 1280 x 1024 71.68 66.68 960 x 768 1000 x 800
SUN76 1280 x 1024 81.13 76.11 960 x 768 1000 x 800
SGI72 1280 x 1024 76.92 72.30 960 x 768 1000 x 800
SGI76 1280 x 1024 82.01 76.00 960 x 768 1000 x 800
UXGA60 1600 x 1200 75.00 60.00 1024 x 768 1066 x 800 O O