Mitsubishi Sl6u Projector User Manual
Here you can view all the pages of manual Mitsubishi Sl6u Projector User Manual. The Mitsubishi manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 11
EN – 11 ENGLISH Projector + Computer Important: •When you use a longer RGB cable instead of the provided cable, the image quality may deteriorate. •Some computers require additional connectors or analog RGB output adapters to be connected with this projector. Contact your dealer for further information. •This projector uses RCA jacks for its audio input. Check the type of the audio output terminal of the connected computer and prepare a proper cable for connection. Some computers don’t have the audio...
Page 12
EN – 12 Preparation Important: •Install the screen on a flat wall at 90 degrees to the floor. •Slanting the projector more than ±10˚ (horizontally) or ±30˚ (vertically) may cause trouble or explosion of the lamp. You can tilt the projector up to 7 degrees using the adjustment feet only. •Images may not be projected in a shape of a regular rectangle or with its aspect ratio 4:3, depending on the installation conditions of the projector and the screen. •To correct vertical keystone distortion, press the...
Page 13
EN – 13 ENGLISH Basic operation Important: •The projector starts warming up when the POWER button is pressed. During the warm-up process, images may appear dark and no commands are accepted. •By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when the STATUS indicator blinks red. (See page 28.) •Images may not be projected with good quality in an extremely hot or cold environment. (This is not a product malfunction.) 4. Adjust the focus by turning the...
Page 14
EN – 14 Basic operation (continued) VOLUME 15 Volume from the speaker Press the VOLUME + or – button to change the volume from the speaker. The volume control bar will appear on the screen. •The volume control bar will disappear about 10 seconds after the VOLUME button is released. •The VOLUME buttons don’t function while the menu selection bar or the menu is being displayed. •When a high-level audio signal, such as a DVD audio signal, is supplied to the AUDIO IN terminal, the output from the speaker...
Page 15
EN – 15
ENGLISH
Menu operation
IMAGE
XGA60opt.
INSTALLATION
opt.XGA60
INSTALLATION
opt.
AUTO POWER
ON
AUTO POWER
OFF
OFF OFF
XGA60
AUTO POWER
ON
AUTO POWER
OFF
OFF OFF
AUTO POWER
ON
AUTO POWER
OFF
30 minOFF
Basic operation
Several settings can be adjusted using the menu.
Example : Auto power off time setting
1. Press the MENU button.
2. Press the $ or % button to select
INSTALLATION.
3. Press the ENTER button (or } button).4. Press the { or } button to select AUTO
POWER OFF.
5. Press the $ or...
Page 16
EN – 16 INSTALLATION opt. ON BACK COLOR AUTO POWER ON AUTO POWER OFF SPLASH SCREEN MUTE MODE LAMP MODEON BLUE BLACKOFF IMAGE CAPTURESETUPOFF STANDARD OFF IMAGE REVERSE XGA60 CONTRAST IMAGE 0 BRIGHTNESS 0 STANDARD 0 COLOR AUTO0 XGA60 COMPUTEROFF TINT 0SHARPNESS COLOR TEMP. GAMMA MODE COLOR MATRIX sRGB opt. Menu operation (continued) 1 IMAGE CONTRAST.........Use to adjust the image contrast. The contrast becomes higher as the value increases. BRIGHTNESS.....Use to adjust the image brightness. The image...
Page 17
EN – 17 ENGLISH 3 FEATURE MENU POSITION ...Use to select the position of the menu on the screen, 1. (upper left) or 2. (lower right). EXPAND MODE .. Choose the mode for enlarging the image. See page 20. AUDIO MODE.....Select COMPUTER to output the audio that is input to the AUDIO IN terminal when COMPUTER is chosen as the source. Select VIDEO to output the audio that is input to that terminal when VIDEO is chosen as the source. Select COMPUTER VIDEO mode to always output the audio that is input to...
Page 18
EN – 18
Image adjustment
CONTRAST R
COLOR TEMP.-USER
0
CONTRAST B 0
BRIGHTNESS R 0
BRIGHTNESS B 0
CONTRAST
IMAGE
0
BRIGHTNESS 0
STANDARD
0
COLOR
AUTO0
XGA60
COMPUTEROFF
TINT
0SHARPNESS
COLOR TEMP.
GAMMA MODE COLOR MATRIX sRGB
opt.
4. Press the { or } button to select the desired
color.
•If you want to adjust the balance of all colors of
the image, select RGB-TINT.
5. Press the $ or % button to adjust the color
balance of the selected color.
6. Repeat steps 4 and 5 for optimum adjustment
results.
7....
Page 19
EN – 19 ENGLISH Adjustment of the image from the computer This projector adjusts the format of the video signal supplied from the computer. However, sometimes images are not projected correctly owing to the type of the computer used. When the image from the computer isn’t projected correctly, press the AUTO POSITION button. (See page 14.) If the image isn’t projected correctly yet, adjust the image from the computer using the menu. To move the image horizontally : Adjust HORIZ. POSITION in the SIGNAL...
Page 20
EN – 20 Advanced features Expand By pressing the EXPAND button on the remote control, you can magnify the image to view the details. You can view the image in its original size in the REAL mode. •The EXPAND mode doesnt work with video or S-video signal. •The EXPAND mode doesnt function with some input signals. For details, see page 31. Still To stop the motion in the image temporarily (or to display a still image): Press the STILL button on the remote control. •The image will freeze temporarily. To...