Mitsubishi Sl4su Projector User Manual

							EN – 11
ENGLISH
Projector + Computer
Important:
•When you use a longer RGB cable instead of the provided cable, the image quality may deteriorate.
•Some computers require additional connectors or analog RGB output adapters to be connected with this
projector. Contact your dealer for further information.
•This projector uses RCA jacks for its audio input. Check the type of the audio output terminal of the connected
computer and prepare a proper cable for connection. Some computers don’t have the audio output terminal.
•Speaker output is mono.
•Set AUDIO MODE in the FEATURE menu to COMPUTER to hear the audio only when the input source is
COMPUTER. (See page 17.)
For Macintosh
•If your Macintosh has no video port, a monitor output adapter is required. Contact your dealer for further
information.
•Some Macintoshes require a MAC adapter for the RGB cable for connection with this projector. Contact your
dealer for further information.
About DDC™
The COMPUTER/COMPONENT VIDEO IN terminal of this projector complies with the DDC1/2B standard.
When a computer supporting this standard is connected to this terminal, the computer will automatically load
the information from this projector and prepare for output of appropriate images.
•After connecting a computer supporting this standard to this terminal, plug the power cord of the projector in
the wall outlet first, and then boot up the computer.
•You may need to install the DDC driver, depending on the computer you use. In this case, you need to
download the driver from our Web site. Contact your dealer or Mitsubishi sales office for further information.
AUDIO OUT
MONITOR OUTPUT
COMPUTER/COMPONENT 
VIDEO IN
AUDIO IN COMPUTER/
COMPONENT 
VIDEO  OUT
RGB cable for PC
Computer
to monitor port
PC audio cable (option)to PC audio
output
RGB cable for PC (option)
Necessary when outputting to both a PC monitor and the projector. 
						

							EN – 12
Preparation
Important:
•Install the screen on a flat wall at 90 degrees to the
floor.
•Slanting the projector more than ±10˚ (horizontally) or
±30˚ (vertically) may cause trouble or explosion of the
lamp. You can tilt the projector up to 7 degrees using
the adjustment feet only.
•Images may not be projected in a shape of a regular
rectangle or with its aspect ratio 4:3, depending on the
installation conditions of the projector and the screen.
•To correct vertical keystone distortion, press the
KEYSTONE button on the projector or the remote
control to display KEYSTONE, and adjust the image
by pressing the }, { button (or VOLUME  +, - button
on the remote control).
In the following cases:Preparation for projection
1. Attach the provided power cord to the projector.
2. Plug the power cord in the wall outlet.
3. Remove the lens cap.
Warning:
•Do not look into the lens directly when the projector is on.
•The lens cap is for protecting the lens. If you leave the
lens cap on the lens with the projector turned on, it
may be deformed because of heat build-up. Remove the
lens cap when you turn on the projector.
•The power cords for use in the U.S. and Europe are
provided with this projector. Use the appropriate cord
for your country.
•This projector uses the power plug of three-pin
grounding type. Do not remove the grounding pin from
the power plug. If the power plug doesn’t fit your wall
outlet, ask an electrician to change the wall outlet.
•The provided power cord for the U.S. is rated at 120 V.
Never connect this cord to any outlet or power supply
using other voltages or frequencies than rated. If you
want to use a power supply using other voltage than
rated, prepare an appropriate power cord separately.
•Use 100-240 V AC 50/60 Hz to prevent fire or electric
shock.
•Do not place any objects on the power cord or do not
place the projector near heat sources to prevent
damage to the power cord. If the power cord should be
damaged, contact your dealer for replacement because
it may cause fire or electric shock.
•Do not modify or alter the power cord. If the power
cord is modified or altered, it may cause fire or electric
shock.
Caution:
•Plug in the power cord firmly. When unplugging, hold
and pull the power plug, not the power cord.
•Do not plug in or out the power cord with your hand
wet. It may cause electric shock.
Adjustment of the projection angle
For the best projection, project images on a flat screen
installed at 90 degrees to the floor. If necessary, tilt the
projector using the two adjustment feet on the bottom of
the projector.
1. Tilt up the project to the appropriate angle.
2. Press the foot adjustment buttons next to the
adjustment feet, and the adjustment feet will come
out.
3. Release the buttons to lock the adjustment feet to that
position.
4. Rotate the adjustment feet for fine adjustment.
After using the projector:
5. Put the adjustment feet back into the projector by
pressing the foot adjustment buttons.
Important:
•When the keystone adjustment is carried out, the
adjustment value is indicated.  Note that this value
doesn’t mean a projection angle.
•The allowable range of the adjustment value in the
keystone adjustment varies depending on the
installation conditions.
•When the keystone adjustment takes effect, the
resolution decreases. In addition, stripes may appear or
straight lines may bend in images with complicated
patterns. They are not due to product malfunctions.
•Noise may appear on the screen during the keystone
adjustment because of the type of the video signal being
projected and the setting values of the keystone
adjustment. In such cases, set the keystone adjustment
values in the range where the image is displayed
without noise.
•When the keystone adjustment is carried out, the
image may not be displayed correctly because of
the type of input signal.
•When the 1080i signal is input, the keystone
adjustment ranges are limited.
ScreenAdjustment feetPress  the }
(or -) button.Press the {
(or +) button. 
						

							EN – 13
ENGLISH
Basic operation
Important:
•The projector starts warming up when the
POWER button is pressed. During the warm-up
process, images may appear dark and no
commands are accepted.
•By blinking red, the STATUS indicator indicates
that the lamp should be replaced soon. Replace
the lamp when the STATUS indicator blinks red.
(See page 26 and 29.)
•Images may not be projected with good quality in
an extremely hot or cold environment. (This is not
a product malfunction.)
4. Adjust the focus by turning the focus ring.
5.  Choose your desired external input source using
the SOURCE button on the remote control or the
COMPUTER or VIDEO button on the control
panel.
•The input source is switched between VIDEO,
S-VIDEO and COMPUTER at every press of
the SOURCE button on the remote control.
•The input source is switched between VIDEO
and S-VIDEO at every press of the VIDEO
button on the control panel.
•The projector automatically selects the
appropriate signal format. The selected signal
format is displayed on the screen.
•The COMPUTER, VIDEO, and SOURCE
buttons don’t function while the menu is being
displayed.
•Images supplied from the computer may
flicker. Press the $ or % button on the remote
control to reduce flicker, if it occurs.
6.   Adjust the image size by turning the zoom ring.
•If necessary, adjust the focus and zoom again.Power-on
1. Turn on the device connected to the projector first.
2. Plug the power cord in the wall outlet.
•The POWER indicator lights up.
•If the power cord is unplugged from the wall
outlet before the projector is cooled down
completely after use, the fans may start
rotating when the power cord is plugged in
next time and the POWER button may not
function. In this case, wait for the fans to stop
and press the POWER button to light the
indicator.
3. Press the POWER button.
•It may take about one minute for the lamp to
light up.
•The lamp occasionally fails to light up. Wait a
few minutes and try to light the lamp again.
•After the POWER button is pressed or the
LAMP MODE is switched, the image may
flicker before the lamp becomes stable. This is
not a product malfunction.
•The STANDARD LAMP MODE is activated by
default whenever the projector is turned on.
When the LOW LAMP MODE has been
chosen, the default STANDARD lamp mode is
switched to the LOW LAMP MODE in 1.5
minutes.
For XL5U only
•You can fix the LAMP MODE to LOW.  (See
page 16.)
55
3, 1, 2
POWER STATUS
VIDEO KEYSTONE
ENTER
MENU COMPUTERAUTO POSITION
POWER
PAGE
VOLUME
EXPAND
SOURCEKEYSTONEAUTOPOSITION
STILLMUTE
ENTER
MENUUP DOWN
5
3, 1, 2
4
6
ConditionIndicator
STATUS
POWER
-
Stand-by
Red
When the lamp is on.
Green
Green
When the lamp is off temporarily.-
Red 
						

							EN – 14
Basic operation (continued)
VOLUME     15
Volume from the speaker
Press the VOLUME + or – button to change the
volume from the speaker.
The volume control bar will appear on the screen.
•The volume control bar will disappear about 10
seconds after the VOLUME button is released.
•The VOLUME buttons don’t function while the
menu selection bar or the menu is being
displayed.
•When a high-level audio signal, such as a DVD
audio signal, is supplied to the AUDIO IN
terminal, the output from the speaker may be
distorted.
AV mute
The video and audio signals are temporarily muted
when the MUTE button is pressed. To cancel muting,
press the MUTE button again.
•If MUTE MODE in the INSTALLATION menu is
set to IMAGE, the splash screen will appear when
the MUTE button is pressed.
•You can alter the splash screen optionally. See
page 21.
•When muting starts, the lamp mode becomes
LOW, darkening the display of IMAGE. This is
not a product malfunction.
Caution:
•After using the projector, wait one minute for the
air outlet fans to stop. Then unplug the power
cord from the wall outlet.
•The lamp can’t be lit again for one minute after
turned off for safety purpose. It will take another
one minute for the STATUS indicator to go out. If
you want to turn on the projector again, wait until
the indicator goes out, and then press the POWER
button.
•The air outlet fans rotate faster as the
temperature around the projector rises.
•When the temperature around the projector rises
high, the sign “TEMPERATURE!!” blinks red on
the screen. If the temperature stays high, the
lamp will go out automatically.
Power-off
Use the following procedure to turn off the projector.
Do not turn off the projector by unplugging the power
cord while the lamp is on. Unplugging while the lamp
is on degrades the lamp’s performance and causes
failure in the projector.
1 1. Press the POWER button.
•The message “POWER OFF? YES : PRESS
AGAIN” appears on the screen.
•To cancel, press any button except the POWER
button. (Some buttons on the remote control
don’t function for cancel.)
2 2. Press the POWER button within 10 seconds again.
•The lamp will go out and the STATUS
indicator will start blinking.
•Though the lamp goes out at this second press
of the POWER button, the air outlet fans
continue operating for one minute to cool down
the lamp and LCD panels. The STATUS
indicator will stop blinking.
3 3. Unplug the power cord.
•The POWER indicator will go out.
•If the power cord should be unplugged
accidentally while either the air inlet fan or the
air outlet fans are operating or the lamp is on,
allow the projector to cool down for 10 minutes
with the power off. To light the lamp again,
press the POWER button. If the lamp doesn’t
light up immediately, repeat pressing the
POWER button two or three times. If it should
still fail to light up, replace the lamp.
Important:
•When storing the projector in the provided
carrying case, the lens should face up.
AUTO POSITION button
When the image isn’t projected in the right position
with COMPUTER selected as the input source, follow
the procedure below.
1. Project a bright image such as the “Recycle Bin”
window on the full screen.
2. If the screen saver is running, turn it off.
3. Press the AUTO POSITION button.
•If the image is still not in the right position,
adjust the image position using the SIGNAL
menu. 
						

							EN – 15
ENGLISH
Menu operation
IMAGE
XGA60opt.
INSTALLATION
opt.XGA60
INSTALLATION
opt.
AUTO POWER 
ON
AUTO POWER 
OFF
OFF OFF
XGA60
AUTO POWER 
ON
AUTO POWER 
OFF
OFF OFF
AUTO POWER 
ON
AUTO POWER 
OFF
30 minOFF
Basic operation
Several settings can be adjusted using the menu.
Example : Auto power off time setting
1.  Press the MENU button.
2.  Press the $ or % button to select
INSTALLATION.
3.  Press the ENTER button (or } button).4.  Press the { or } button to select AUTO
POWER OFF.
5.  Press the $ or % button to adjust the auto
power off time.
6.  Exit the menu by pressing the MENU button
several times.
Important:
•When the MENU button doesn’t function,
unplug the power cord from the wall outlet.
Wait about 10 minutes, plug the power cord in,
and try again.
•After selecting the items marked with 
, press
the ENTER button.
IMAGE CONTRAST± 30BRIGHTNESS
COLOR MATRIX± 30sRGB ON , OFF
STANDARDLOWHIGHUSER    
COLOR TEMP.
COLOR± 10TINT± 10SHARPNESS± 5GAMMA MODE AUTO, DYNAMIC, STANDARD, THEATERCONTRAST R± 30
CONTRAST B± 30BRIGHTNESS R± 30BRIGHTNESS B± 30
EXPAND MODEEXPAND, REALAUDIO MODE COMPUTER, VIDEO, COMPUTER VIDEO, MUTE
INSTALLATION
OFF, MIRROR, INVERT, MIRROR INVERT
AUTO POWER ON
ON , OFF
RESET ALL OK 
AUTO POWER OFF
ON , OFF
FEATURE MENU POSITION 1 (Upper left), 2(Lower right)
IMAGE REVERSE
SPLASH SCREEN
BLACK, IMAGEMUTE MODEBLUE, BLACK, IMAGEBACK COLOR
STANDARD, LOWLAMP MODE
OFF, CENTER, UPPER, LOWER  ANAMORPHICDISPLAY INPUT    , MENU ACCESS    , SPLASH ID SCREENPASSWORD FUNCTION
ON , OFFSCART INPUTVIDEO SIGNAL AUTO , NTSC , PAL , SECAM , 4.43NTSC , PAL-M , PAL-N , PAL-60
LANGUAGE, English, Español, Deutsch, Français, Italiano,        ,          ,             ,    
VIDEO
YELLOW± 30RED± 30
BLUE± 30CYAN± 30GREEN± 30
MAGENTA± 30RGB-TINT± 20
COMPUTER USEROFF
SIGNALHORIZ.POSITION
HOLD0 - 999VERT.POSITION 0 - 999FINE SYNC. 0 - 31TRACKING
USER0 - 9999CLAMP POSITION0 - 63CLAMP WIDTH 1 - 63
SHUTTER (L)
0 - 20SHUTTER (U)
0 - 20
SHUTTER (RS)
0 - 20SHUTTER (LS)
0 - 20
VERT. SYNC.
AUTO, OFF
*5
*3 *3
AUTO , OFFCINEMA MODE
*3
*3 *3
*3
*3
*3 *5
*5
ONBEGIN 0 - 15END 0 - 15 OFF
COMPUTER INPUTRGB, YCBCR / YPBPR
*5
*5
OFF,  5,  10,  15,  30,  60 min
OK 
ON
UNLOCKOK LOCK
*1
*1
*1
*2 *1
*1
*3
*4 *2
IMAGE CAPTURESETUPx1, x2, FULLGLAY, RED, GREEN, BLUE, BLACK, WHITE, RED 50%, GREEN 50%, BLUE 50%
CAPTURE
BACK COLORSIZEGO
(Displayed only when the source is VIDEO or S-VIDEO.)
(Displayed only when the source is VIDEO or S-VIDEO.)
(These items are not available when the input
source is COMPUTER.)
* 1: Not available when sRGB is set to ON.
* 2: Not available with certain signals.
* 3: Not available when the source is a VIDEO
      or S-VIDEO signal.
* 4: Available only when the input signal is TV60, 480i.
* 5: Setting range differs depending on the input signals. 
						

							EN – 16
INSTALLATION
opt.
ON
BACK COLOR AUTO POWER 
ON
AUTO POWER 
OFF
SPLASH 
SCREEN
MUTE MODE
LAMP MODEON
BLUE
BLACKOFF
IMAGE
CAPTURESETUPOFF
STANDARD
OFF IMAGE 
REVERSE
XGA60
CONTRAST
IMAGE
0
BRIGHTNESS 0
STANDARD
0
COLOR
AUTO0
XGA60
COMPUTEROFF
TINT
0SHARPNESS
COLOR TEMP.
GAMMA MODE COLOR MATRIX sRGB
opt.
Menu operation (continued)
1 IMAGE
CONTRAST.........Use to adjust the image contrast. The contrast becomes higher
as the value increases.
BRIGHTNESS.....Use to adjust the image brightness. The image becomes
brighter as the value increases.
sRGB....................Choose ON for projection emphasizing on the color
reproducibility.
•When sRGB is ON, COLOR MATRIX, COLOR TEMP.,
COLOR, TINT, and GAMMA MODE cant be adjusted.
COLOR MATRIX . Use to adjust the color balance in each color of the image. See
page 18.
COLOR TEMP.....Use to adjust the color temperature. See page 18.
COLOR................Use to adjust the color intensity of the image.
TINT....................Use to adjust the color balance of the image. The color balance
shifts to green as the value increases and shifts to purple as
the value decreases. (Available only when VIDEO is chosen as
the source.)
•When the TV50 (PAL, SECAM) signal is input, TINT cant be adjusted.
SHARPNESS.......Use to adjust the image sharpness. The image becomes sharp as the value increases. (Available only
when VIDEO is chosen as the source.)
GAMMA MODE ... When AUTO is selected, the appropriate gamma mode is automatically selected depending on the
input signal. For normal use, select  AUTO. Select DYNAMIC for computer sources. Select
STANDARD for sport scenes and video sources. Select THEATER for film sources.
2 INSTALLATION
AUTO POWER ON......When ON is chosen, the lamp is automatically lit when the
power cord is plugged in the wall outlet. Choose ON when
using the projector mounted on the ceiling.
•The projector is in the stand-by mode when the lamp
is off.  Use the remote control to turn on the lamp.
AUTO POWER OFF Use to set the time elapsed before the projector enters the
stand-by mode when there is no signal input from the source.
IMAGE CAPTURE Use to capture the screen for the splash screen. See page 21.
SPLASH SCREEN Choose ON to display the splash screen when the power is
turned on.
•The splash screen can be changed. See page 21.
BACK COLOR......Use to select the background from among BLUE, BLACK and
IMAGE, which will be displayed when there is no signal input from the source. When IMAGE is
selected, the splash screen will be displayed.
MUTE MODE......Use to choose the background, either BLACK, or IMAGE, which will be displayed when the MUTE
button is pressed. When IMAGE is chosen, the splash screen will be displayed.
LAMP MODE.......Use to change the brightness of the lamp. When LOW is chosen, the lamp brightness is kept low
and the volume of the operation sound is reduced, resulting in a longer lamp replacement interval.
 •The STANDARD LAMP MODE is activated by default whenever the projector is turned
on. When the LOW LAMP MODE has been chosen, the default STANDARD LAMP
MODE is switched to the LOW lamp mode in 1.5 minutes.
•When the LAMP MODE is switched, the projected image may flicker. This is not a
product malfunction.
For XL5U only
•You can fix the LAMP MODE to LOW.
How to fix the LAMP MODE to LOW
In stand-by mode, keep pressing the AUTO, KEYSTONE, and COMPUTER buttons on
the  control panel together about three seconds. (The STATUS indicator is lit in orange
for one second.)
How to cancel the fixed LAMP MODE
In stand-by mode, keep pressing the VIDEO, KEYSTONE, and } buttons on the
control panel together about three seconds. (The STATUS indicator is lit in green for one
second.)
Important:
•Within 10 seconds after the STATUS lamp is lit, do not unplig the power cord
nor turn the POWER button to ON.
IMAGE REVERSE ..Use to reverse the projected image. Select MIRROR for rear projection with the tabletop-mounted
projector. Select MIRROR INVERT for front projection with the ceiling-mounted projector.
•When you continue projection for a long time with BACK COLOR or MUTE MODE set to IMAGE, an after-
image may persist on the screen.
•Do not change the setting of LAMP MODE frequently.
•You can’t set IMAGE CAPTURE or SPLASH SCREEN when PASSWORD FUNCTION in the FEATURE
menu has been set to SPLASH ID SCREEN to enable the password lock. 
						

							EN – 17
ENGLISH
3 FEATURE
MENU POSITION ...Use to select the position of the menu on the screen,  1. 
(upper left) or 2.  (lower right).
EXPAND MODE .. Choose the mode for enlarging the image. See page 20.
AUDIO MODE.....Select COMPUTER to output the audio that is input to the
AUDIO IN terminal when COMPUTER is chosen as the
source. Select VIDEO to output the audio that is input to that
terminal when VIDEO is chosen as the source. Select
COMPUTER VIDEO mode to always output the audio that is
input to that terminal. Select MUTE not to output the audio at
all.
CINEMA MODE .. When AUTO is selected, the film mode will be automatically
activated when a film source signal is inputted. When OFF is
selected, the film mode will not be activated.
VIDEO SIGNAL ... When AUTO is selected, the appropriate video format is
automatically selected depending on the input signal. If the
image isn’t displayed correctly, select the desired video format manually.
SCART INPUT.....Choose ON when connecting the projector with a device equipped with the SCART terminal that
can output RGB signal. SCART terminal is used mainly in Europe. Choose OFF normally.
ANAMORPHIC....Select the desired position from among UPPER, CENTER, and LOWER when playing DVD discs
containing data of letterboxed images.
PASSWORD FUNCTION .Use to change the mode of the password lock or to enable or cancel the password lock. See page 23
for details.
LANGUAGE........Use to select the language used in the menu. (
 / English / Español / Deutsch / Français /
Italiano / 
/  /  / )
RESET ALL.........Use to reset the menu settings (except IMAGE CAPTURE, PASSWORD, and LANGUAGE ).
•CINEMA MODE can be adjusted only when a TV60,480i signal is being displayed.
•When SCART INPUT is set to ON, nothing is output to the external monitor.
•When SCART INPUT is set to ON, normal computer signals aren’t projected.
•Use a SCART-BNC (or SCART-Mini D-SUB 15P) cable (option) when connecting this projector with an AV
device equipped with the SCART terminal.
•Some AV devices equipped with the SCART terminal aren’t compatible with this projector.
•When VIDEO SIGNAL is set to AUTO, the image may not be projected with correct colors. Change the
setting of VIDEO SIGNAL depending on the input signal in such cases.
•When ANAMORPHIC is set to except OFF, the keystone adjustment ranges are limited.
4 SIGNAL
HORIZ. POSITION ...Use to adjust the horizontal position of the image.
VERT. POSITION ...Use to adjust the vertical position of the image.
FINE SYNC..........Use to synchronize the projector with the PC input signal so
that the image is not blurred.
TRACKING..........Use to eliminate image noise such as wide stripes.
COMPUTER INPUT ...The projector adjusts its settings automatically when
connected to a DVD player equipped with a component video
output (Y, C
B, CR). When the projector is connected with a
device having an RGB terminal, choose RGB manually.
HOLD..................Use to adjust the image when flagging occurs near the top of
the screen.
5 SIGNAL - USER (No need to adjust in normal use.)
CLAMP POSITION/
CLAMP WIDTH ... Use to correct solid white or solid black in the projected image.
VERT.SYNC.........Use to adjust the image when its motion doesn’t run smoothly.
Select AUTO for normal use.
SHUTTER (U)......Use to adjust the image when noise appears on the top part of the
image.
SHUTTER (L)......Use to adjust the image when noise appears on the bottom part of
the image.
SHUTTER (LS)....Use to adjust the image when noise appears on the left half of the
image.
SHUTTER (RS)....Use to adjust the image when noise appears on the right half of
the image.
•If any setting of the SIGNAL-USER menu is changed, the image maynot be displayed correctly. In this
case, press the AUTO POSITION button.
Important:
•You can set the IMAGE, SIGNAL, and SIGNAL-USER menus only when the signal is supplied.
•TV60 and TV50 are equivalent to 480i and 576i respectively. Settings made for one of them apply
automatically when its counterpart is supplied.
FEATURE
OFF
OFF
XGA60
AUTO EXPAND
opt.
MENU POSITION
EXPAND MODEAA
VIDEO SIGNAL?
ANAMORPHIC
RESET ALL
English
LANGUAGEAË
OK
SCART INPUT
DISPLAY
INPUT PASSWORD
FUNCTION
CINEMA MODEAUTO
AUDIO MODECOMPUTER
VIDEO1.
CLAMP 
POSITIONSIGNAL-USER
0
CLAMP WIDTH 1
SHUTTER (U) 0
SHUTTER (L) 0
SHUTTER (LS) 0
SHUTTER (RS) 0
VERT. SYNC. AUTO?
R G BR G B
SIGNAL
HORIZ. POSITION 0
VERT. POSITION 0
TRACKING 0
COMPUTER 
INPUTRGB
FINE SYNC. 0
USER
XGA60opt.
OK
ONHOLD 
						

							EN – 18
Image adjustment
CONTRAST R
COLOR TEMP.-USER
0
CONTRAST B 0
BRIGHTNESS R 0
BRIGHTNESS B 0
CONTRAST
IMAGE
0
BRIGHTNESS 0
STANDARD
0
COLOR
AUTO0
XGA60
COMPUTEROFF
TINT
0SHARPNESS
COLOR TEMP.
GAMMA MODE COLOR MATRIX sRGB
opt.
4.  Press the { or } button to select the desired
color.
•If you want to adjust the all color balance of
the image, select RGB-TINT.
5.  Press the $ or % button to adjust the color
balance of the selected color.
6. Repeat steps 4 and 5 for optimum adjustment
results.
7. Exit the menu by pressing the MENU button
several times.
•When the input source is VIDEO or COMPUTER,
the setting items in the color matrix adjustment
are automatically set to the predetermined values.
You can change these settings manually.
•To cancel the color matrix adjustment, select OFF
in step 2.
•When the color matrix adjustment is carried out,
the colors in the menu will also vary. This isn’t a
product malfunction.
Color temperature
1.  Select COLOR TEMP. in the IMAGE menu.
2.  Press the $ or % button to select USER 
.
3.  Press the ENTER button.
4.  Press the { or } button to select the desired
item.
5.  Press the $ or % button to adjust the selected
item.
6. Repeat steps 4 and 5 for optimum adjustment
results.
7. Exit the menu by pressing the MENU button
several times.
COLOR MATRIX
0
0
0
0
0
0
0RED
RGB-TINT
GREEN
BLUE
YELLOW
CYAN
MAGENTA
About color temperature
There are different kinds of white color. Color
temperature is a way to show the differences in
white. White of which temperature is low appears
reddish. When the color temperature rises, white
appears bluish. This projector adjusts this color
temperature by changing the values of contrast
blue and red.
To rise the color temperature:
Increase the CONTRAST B (blue) and decrease the
CONTRAST R (red).
To reduce the color temperature:
Decrease the CONTRAST B (blue) and increase
the CONTRAST R (red).
Image adjustment
You can adjust the image using the IMAGE menu.
To control the white-to-black level of the image :
Adjust CONTRAST in the IMAGE menu.  Press the
% button to increase the contrast and the $ button
to reduce it.
To control the light level of the image :
Adjust BRIGHTNESS in the IMAGE menu.  Press
the % button to lighten the image and the $ button
to darken it.
To determine the intensity of the color :
Adjust COLOR in the IMAGE menu.  Press the %
button to increase the amount of color in the image
and the $ button to decrease it.
To adjust the red-green color balance of the
image :
Adjust TINT in the IMAGE menu.  Press the %
button to increase the amount of green in the image
and the $ button to increase the amount of red in
the image.
To adjust the detail and clarity of the image :
Adjust SHARPNESS in the IMAGE menu.  Press the
% button to sharpen the image and the $ button to
soften the image.
Color matrix
This projector adjusts the color balance in each color
of RGB (red, green, and blue), and their neutral
colors (yellow, cyan, and magenta) by the color
correction adjustment. Use the color correct
adjustment when you want to emphasize color or
when only a certain color balance is not correctly
adjusted.
1.  Select COLOR MATRIX in the IMAGE menu.
2.  Press the $ or % button to select USER 
.
3.  Press the ENTER button. 
						

							EN – 19
ENGLISH
Adjustment of the image from the
computer
This projector adjusts the format of the video signal
supplied from the computer. However, sometimes
images are not projected correctly owing to the type
of the computer used. When the image from the
computer isn’t projected correctly, press the AUTO
POSITION button. (See page 14.) If the image isn’t
projected correctly yet, adjust the image from the
computer using the menu.
To move the image horizontally :
Adjust HORIZ. POSITION in the SIGNAL menu.
Press the % button to move the image to the left.
Press the $ button to move the image to the right.
To move the image vertically :
Adjust VERT. POSITION in the SIGNAL menu.
Press the % button to move the image upward.
Press the $ button to move the image downward.
When the image flickers or the image is out of
focus :
Adjust FINE SYNC. in the SIGNAL menu.
When the top part of the image flags :
Change the setting of HOLD in the SIGNAL menu.
Select ON 
, press the ENTER button, and adjust
BEGIN or END to minimize the flagging.
When wide strips appear :
Adjust CLAMP POSITION or CLAMP WIDTH in the
SIGNAL - USER menu.
When the motion doesnt run smoothly :
Adjust VERT. SYNC. in the SIGNAL - USER menu.
Select AUTO for normal use.
When noise appears on the right or left half of
the image :
Adjust SHUTTER (LS) or SHUTTER (RS) in the
SIGNAL - USER menu.
When noise appears on the top or bottom part
of the image :
Adjust SHUTTER (U) or SHUTTER (L) in the
SIGNAL - USER menu.
R G BR G B
SIGNAL
HORIZ. POSITION 0
VERT. POSITION 0
TRACKING 0
COMPUTER 
INPUTRGB
FINE SYNC. 0
USER
XGA60opt.
OK
ONHOLD
CLAMP 
POSITIONSIGNAL-USER
0
CLAMP WIDTH 1
SHUTTER (U) 0
SHUTTER (L) 0
SHUTTER (LS) 0
SHUTTER (RS) 0
VERT. SYNC. AUTO?
Important:
Do not change any of the settings in the SIGNAL-
USER menu for normal use.
Simple adjustment method
1. Select HORIZ. POSITION in the SIGNAL menu.
2. Press the $ or % button to adjust the horizontal
start position (or the left side of the image).
3. Select TRACKING in the SIGNAL menu.
4. Press the $ or % button to adjust the horizontal
end position (or the right edge of the image).
5. Repeat steps 1 to 4 for optimum adjustment
results.
6. Select VERT. POSITION in the SIGNAL menu.
7. Press the $ or % button to adjust the vertical
start position (or the upper edge of the image). 
						

							EN – 20
Advanced features
Expand
By pressing the EXPAND button on the remote
control, you can magnify the image to view the
details. You can view the image in its original size in
the REAL mode.
•The EXPAND mode doesnt work with video
or S-video signal.
•The EXPAND mode doesnt function with some
input signals. For details, see page 32 or 33.
Still
To stop the motion in the image temporarily (or
to display a still image):
Press the STILL button on the remote control.
•The image will freeze temporarily.
To resume the motion in the image:
Press the STILL button on the remote control again.
To choose the EXPAND or REAL mode:
1. Press the MENU button.
2. Press the $ or % to select the FEATURE menu.
3. Press the ENTER button.
4. Press the  { or } button to select EXPAND MODE.
5. Press the $ or % to choose EXPAND or REAL.
6. Press the MENU button twice to exit the menu.
To use the EXPAND mode:
1. Press the EXPAND button.
•You can select the area to be magnified by
pressing the {, }, $, or % button on the
remote control.
•You can change the magnification of the se-
lected area by pressing the + or - button.
2. Press the EXPAND button again to the exit the
EXPAND mode.
•The regular operation screen will appear.
Important:
•In the EXPAND mode, you cant adjust the vol-
ume.
To use the REAL mode:
1. Press the EXPAND button.
•In the REAL mode, press the $ or % button on
the remote control for fine adjustment.
•In the REAL mode, the AUTO POSITION button
doesnt function. When this button is pressed, the
prohibition mark (
) appears on the screen.
2. Press the EXPAND button again to the exit the
REAL mode.
•The regular operation screen will appear.
EXPAND REAL
Magnified
imageNative resolution
display