Mitsubishi Sd420u Projector User Manual

							EN-21
ENGLISH
Password function This projector is equipped with the password function that is 
designed for prevention of wrong operation by children and restriction 
on operation by other than specified users.  
MENU ACCESS  ........ All the buttons except for the POWER button 
on the projector are disabled. (The buttons on 
the remote control are enabled.) You can use 
this mode as a measure of prevention of 
wrong operation by children and restriction on 
operation by other than specified users. 
To enable the password function: 
1. Display the FEATURE menu. 
2. Press the S or T button to select PASSWORD FUNCTION. 
3. Press the ENTER button. 
 The screen for setting the password function will appear.
 When the password has already been set, the mode won’t 
be changed. In such cases, press the ENTER button to can-
cel the password function and try again. 
4. Press the ENTER button.
 The screen for entering a password will appear.
5. Press the S or T button to select a number from 0 to 9.
6. Press the X button.
 You can set the next digit.
7. Repeat steps 5 and 6 to set a four-digit password.
8. Enter the password again for confirmation using the same 
steps.
9. Select OK, and press the ENTER button.
 If the entered passwords don’t match, an error message will 
appear.
 To cancel the procedure, select CANCEL, and press the 
ENTER button.
 You can cancel the procedure by pressing the MENU button 
alternatively.
To cancel the password function: 1. Display the FEATURE menu. 
2. Press the S or T button to select PASSWORD FUNCTION. 
3. Press the ENTER button. 
 The screen for canceling the password function will appear. 
4. Press the ENTER button. 
 The screen for entering the password will appear. 
5. Press the S or T button to select a number from 0. to 9. 
6. Press the X button. 
 You can set the next digit. 
7. Repeat steps 5 and 6 to enter the four-digit password. 
8. Press the X button, select OK, and press the ENTER button. 
 If you enter a wrong password, an error message will 
appear.
 To cancel the procedure, press the X button, select CAN-
CEL, and press the ENTER button.
 You can cancel the procedure by pressing the MENU button 
alternatively. 
Important:  If you forget your password, keep pressing the MENU and 
ENTER buttons on the control panel at the some time about three 
seconds to cancel the password function.
MENU ACCESS
XGA60opt.
LOCK
UNLOCKOK
OK
PASSWORD
CONFIRM
O K CANCEL
MENU ACCESS
XGA60opt.
LOCK
UNLOCKOK
OK
PASSWORD
O K CANCEL
01_ENG.fm  Page 21  Friday, May 26, 2006  4:19 PM 
						

							EN-22
Lamp replacement
When the lamp no longer functions, replace it with a new one.
Caution: Do not remove the lamp immediately after using the projector. You 
may get burned because the lamp very hot after use.
 Before replacing the lamp, press the POWER button to turn off the 
lamp and wait for two minutes for lamp to cool down. Unplug the 
power cord from wall outlet and wait one hour for the lamp to cool 
down completely.
 Do not remove the lamp except for replacement. Careless han-
dling can cause injury or fire.
 Do not touch the lamp directly. It may break and cause injury or 
bur n.
 Be sure not to drop the lamp lid screw into the projector. Also be 
sure not to put metal or any flammable objects inside because it 
may cause fire or electric shock. If any objects should fall inside, 
unplug and contact your dealer.
 Install the lamp securely to prevent failure and fire.
 If the lamp should break, small glass fragments may fall out 
through the grilles and some may remain inside of the projector or 
the lamp box. When taking the lamp box out, be sure to turn over 
the projector and hold the handle of the lamp box to avoid injury 
due to the glass fragments.
 If the lamp should break, never shake the lamp box or hold it in 
front of your face after removing it. The lass fragments may fall out 
and cause injury to your eyes.
 When placing the projector upside down to replace the lamp or 
conduct maintenance, ensure that the projector is securely placed 
before working with it.
1. Reverse the projector gently.
2. Loosen the screws (a) using a Phillips 
screwdriver (+), and remove the lamp 
cover (b).
3. Loosen the screws (c) using a Phillips 
screwdriver (+).
4. Pull up the handle.
5. Pull out the lamp box by the handle 
while holding the projector.
 Pull the lamp box out of the projec-
tor slowly. If it is pulled out quickly, 
the lamp may break scattering 
glass fragments.
 Do not spill liquid on the removed 
lamp box or do not place it near any 
flammable object or where children 
can reach to prevent injury or fire.
6. Load a new lamp box securely into the 
projector in the right orientation.
7. Put the handle back to the original posi-
tion.
 Make sure that the handle is 
locked.
8. Tighten up the screws (c) using a Phil-
lips screwdriver (+).9. Tighten up the screw (a) using a Phillips 
screwdriver (+) to secure the lamp 
cover.Reset of the lamp operation timePlug in the power cord, and reset the lamp 
operation time by keep pressing the W, X, 
and POWER buttons on the control panel at 
the same time about three seconds.
Important: Unless these three buttons are pressed 
at the same time, the lamp operation time 
isn’t reset.
 Make sure that the STATUS indicator is lit twice and the lamp oper-
ation time is reset successfully.
 The projector doesn’t turn on if the lamp cover isn’t attached 
securely.
 Be sure to reset the lamp operation time whenever you replace the 
lamp.
 Do not reset the lamp operation time unless you replace the lamp.
Caution: The lamp is fragile. If it is broken, be careful not to cut yourself with 
glass fragments.
 Contact your dealer for a new lamp.
Interval of lamp replacementWhen the lamp shutdown notice is issued, the lamp replacement is 
recommended even if the lamp is lit normally. Decrease in lumines-
cence and/or color brightness indicates that the lamp needs to be 
replaced. When the lamp operation time exceeds the time elapsed 
until the lamp shutdown notice
*1 is issued, the indicator will blink alter-
nately green and red while the lamp is lit (while the lamp is not lit, the 
indicator will blink red only) and the lamp replacement message will 
appear on the screen for one minute every time the lamp is turned on. 
When the lamp operation time exceeds the time elapsed until the 
lamp shutdown warning
*2 is issued, the replacement message (LAMP 
EXCHANGE) will appear on the screen for one minute at fixed inter-
vals
*4 thereafter.
When the lamp operation time exceeds the time elapsed 
until the lamp shutdown*3, the projector automatically 
shuts off and can’t be used until the lamp is replaced and 
the lamp operation time is reset.
The times above are when LAMP MODE of the INSTALLATION menu 
is set to LOW. When it is set to STANDARD, this duration will be short-
ened.
*4These intervals vary depending on the lamp mode setting.*5When LAMP MODE is set to STANDARD, the time elapsed until 
the lamp shutdown will be shortened to 2000 hours.
Caution: This projector uses a lamp that contains mercury. Disposal of the 
lamp or the projector with the lamp may be regulated due to envi-
ronmental considerations. For disposal or recycling information, 
please contact your local authorities or the Electronic Industries 
Alliance: www.eiae.org. (For US only).
(a)
(b)
(c)
XD420U/SD420U
*1 3000 Hours*2 3800 Hours*3 4000 Hours*5
(a)
(b)
01_ENG.fm  Page 22  Friday, May 26, 2006  4:19 PM 
						

							EN-23
ENGLISH
Troubleshooting
The following offers solutions to some of the common problems you may encounter. We suggest that you consult this chart before contacting your 
dealer. 
Images aren’t projected on the screen. 
 
ProblemCause and solution 
Power isn’t turned on.  Check the states of the indicators. 
Images aren’t projected on the screen. Cancel the AV mute by pressing the MUTE button. 
 Remove the lens cap. 
 The lamp sometimes takes about one minute to light up. 
 On rare occasion, the lamp fails to light up. In such cases, wait a few minutes and try to light the lamp again. 
 If the projector was turned off before the lamp cooled down completely, the fans may start rotating and the 
POWER button may not function when you plug the power cord into the wall outlet next time. Wait for the fans 
to stop and press the POWER button to turn on the lamp again. 
 Check that the lamp cover are closed. 
 Check that the cable connected to the external device isn’t broken. 
 When an extension cord is being used, replace it with the supplied cable and check whether images are pro-
jected correctly. If images are projected correctly, use an RGB signal amplifier along with the extension cord. 
Images suddenly disappear.  The air inlet or outlet grille may be blocked. (In such cases, the STATUS indicator blinks orange.) 
JRemove the objects blocking the air inlet or outlet grille and carry out the following. 
1. Wait for the air inlet or outlet fan to stop (or wait for the STATUS indicator to go out.) 
2. Unplug the power cord from the wall outlet. 
3. Wait about 10 minutes. 
4. Plug the power cord into the wall outlet. 
5. Press the POWER button. 
 When the STATUS indicator is blinking red, it is indicating that the lamp should be replaced. Replace the lamp 
in this case. 
NO SIGNAL is displayed.  Turn on the power of the connected device, or check whether there is something wrong with the connected 
device. 
 Check whether the external device outputs signals. (Check this especially when the external device is a note-
book computer.) 
 Check that the cable connected to the external device isn’t defective. 
 Check that the projector is connected to the external device using the correct terminals. 
 Check that the connected device is correctly selected as the input source. 
 When an extension cord is being used, replace it with the supplied cable and check whether images are pro-
jected correctly. If images are projected correctly, use an RGB signal amplifier along with the extension cord. 
POWER
Off
Steady red
Blinking red 
/ gr een
STATUS
Off
Off
Blinking 
orange
Blinking 
green
Steady red
Off
Steady
or
Blinking
  Solution
If any objects ar e blocking the air inlet or outlet grille, remove them and carry out 
the following.
1. 
2. 
3.  Plug the power cor d into the wall outlet.
4.  Press the POWER button.
Replace the lamp. (The lamp is at the end of its life.)
Attach the lamp cover on the bottom.
Connect the power cord to the projector. 
Plug the power cord into a wall outlet. 
Unplug the power cord from the wall outlet.
Make sure that the projector has cooled off. 
If any objects are blocking the air inlet or outlet grille, remove them.
Dont expose the air outlet grilles to hot air emitted from a heating appliance.
After the STATUS indicator stops blinking, press the POWER button.
If you unplug the power cord while the fan is rotating, the lamp may not turn on about 
one minute when you plug the power cord next time. 
The lamp cant turn on again for one minute after it goes out. 
Press the POWER button several times.
Unplug the power cord from the wall outlet and contact your dealer.
01_ENG.fm  Page 23  Friday, May 26, 2006  4:19 PM 
						

							EN-24
Troubleshooting (continued)
Images aren’t projected correctly.
ProblemCause and solution 
Projected images are shaking.
Projected images are displaced. Check that the cable connected to the external device isn’t intermittent. 
 Connect the cable’s plug with the external device’s connector firmly. 
 Press the AUTO POSITION button. 
 Some computers output out-of-spec signals on rare occasion. Adjust the SIGNAL menu. (See page 19.) 
Projected images are distorted.   Adjust the projector and the screen so that they are perpendicular to each other. (See page 12.) 
Projected images are dark.  Adjust BRIGHTNESS in the IMAGE menu. (See page 18.) 
 Replace the lamp. (See page 22.) 
 Remove the lens cap.
Projected images are blurred.  Adjust the focus. (See page 13.) 
 Clean the lens. 
 Remove the lens cap.
 Press the W or X button on the remote control to eliminate flicker. 
 Adjust BRIGHTNESS and CONTRAST in the IMAGE menu. (See page 18.) 
 Adjust the projector and the screen so that they are perpendicular to each other. (See page 12.)
White dots are seen on projected images.
Black dots are seen on projected images.  This symptom is normal for a DLP projector and is not a malfunction. (A very small number of pixels may stay 
lit or out, but such symptom is not a malfunction. Pixels of 99.99% or more are effective.) 
Rainbow blur appears in projected images.  This is due to color breaking noise that occurs in a DLP system and is not a malfunction. 
Fine streak pattern appears in projected images. It occurs because of interference with the screen and isn’t a product malfunction. Change the screen or read-
just the focus of the projector.
Projected images (and/or audio) appear wavy and 
distorted. Connect the cable’s plug with the external device’s connector firmly. 
 Keep the projector away from equipment generating interfering radio waves. 
 When the keystone adjustment is carried out, the image may not be displayed correctly because of the type 
of input signal. This isn’t a product malfunction. In this case, readjust the keystone so that the amount of key-
stone correction is as small as possible. 
Tint in projected images is incorrect. Check that COMPUTER INPUT in the SIGNAL menu is correctly set. (See page 17.) 
 Check that the cable connected to the external device isn’t broken. 
Only the motion areas in the images supplied from 
the computer aren’t displayed.  This is caused by the computer being used. Contact the manufacturer of your computer.
Projected images are obscured. Match the output resolution of your computer with the resolution of the projector.  For the method to change 
the output resolution of the computer, contact the manufacturer of your computer. (See page 29.) 
 Some images and texts appear obscured during the keystone adjustment. In such cases, use the projector 
without applying the keystone adjustment. (See page 12.)
01_ENG.fm  Page 24  Friday, May 26, 2006  4:19 PM 
						

							EN-25
ENGLISH
Others
When the problems below occur after the lamp is replaced, check the following.
Maintenance 
Warning:Do not use flammable solvents (benzene, thinner, etc.) and flammable aerosols when cleaning the projector body and lens. Flammable substances 
may ignite causing fire or breakdown while the lamp is illuminating.
Caution: Be sure to turn off the lamp and unplug the power cord from the wall outlet before you perform any maintenance on the projector. 
Cleaning of the projector and the ventilation slots Use a soft cloth to clean the projector and the ventilation grilles. When the grilles become dirty, wipe them with a soft cloth dampened with diluted 
mild detergent, and then wipe them with a dry cloth. 
To protect the surface of the projector from fading or deteriorating:  Do not spray insecticide on or inside the projector. 
 Do not use benzine or thinner to clean it. 
 Do not let rubber or plastic materials contact with projector. 
Cleaning of the lens Use a standard lens-cleaning brush or a piece of lens tissue dampened with lens cleaning fluid. The lens surface is fragile. Use only recommended, 
nonabrasive lens-cleaning materials. Do not touch the lens with your fingers. 
 
ProblemCause and solution 
Hot air is emitted from the air outlet grilles.  This air comes out as a result of cooling the inside of the projector. This isn’t a product malfunction. 
No audio is output.   Check that the volume isn’t set to low. 
The menu can’t be used.  The microcomputers inside the projector may be wrongly operating because of noise. 
JPress the POWER button to turn off the lamp and unplug the power cord from the wall outlet. Wait about 
10 minutes, plug the power cord in, and try again. 
TEMPERATURE!! is displayed. This indication appears when the ambient temperature rises high. When the ambient tempera-ture stays 
high, the lamp goes out.
JEliminate any causes of the rise in the ambient temperature. 
 This indication appears when the air inlet or outlet grille is blocked. When they are kept blocked, the lamp 
goes out. 
JRemove the objects blocking the air inlet or outlet grille. 
The   mark appears.  This mark appears when ineffective operation is carried out. This isn’t a product malfunction. 
The remote control doesn’t function easily or at all.  Check that the battery is loaded in the remote control or the battery isn’t weak. (See page 8.) 
 Check that the remote control sensor isn’t exposed to direct sunlight or fluorescent light. (See page 8.) 
 Use the remote control within its operation range. (See page 8.) 
 Use the remote control at least 10 cm away from the projector. 
The buttons on the control panel (except for the 
POWER button) don’t function. The password function is working. 
JCancel the password lock. (See page 21.)
Abnormal sound is heard.  Because the color wheel spins at a high speed, metallic sounds may be heard in rare occasions. Such symp-
tom is not a malfunction. 
ProblemCause and solution 
The power isn’t turned on.  Attach the lamp cover on the bottom correctly. 
 Reset the lamp operation time. (See page 22.) 
The STATUS indicator blinks.   Reset the lamp operation time. (See page 22.) 
01_ENG.fm  Page 25  Friday, May 26, 2006  4:19 PM 
						

							EN-26
Indicators
This projector has two indicators, each of which shows the operation condition of the projector. 
The following offer solutions to possible problems. If these problem persist, turn the projector off and consult your dealer.
Normal condition
Abnormal condition
POWERSTATUSCONDITIONNOTE
Stand-by
Lamp stand-by (about 1 minute)The POWER button cannot be used to switch 
between on and off.
The power is on. (Normal condition)
STATUS indicatorPOWER indicator
Steady redOff
Steady greenBlinking  green
Steady greenSteady green
POWERSTATUSCONDITIONPOSSIBLE SOLUTION
Abnormal temperature
 The ventilation grilles is clogged with dust or dirt.
 The room temperature is high. Clean the ventilation grilles.
 Relocate the projector to a cooler place.
The protection circuit is working or the lamp is in an abnormal con-
dition. Wait until the STATUS indicator goes out, then 
press the POWER button.
 If the above solution is not effective, replace the 
lamp.
The lamp operation time exceeds the time elapsed until the lamp 
shutdown notice while the power is on. (See page 22.)
Replace the lamp.
Change with a new lamp if this problem recurs. The lamp operation time exceeds the time elapsed until the lamp 
shutdown notice while the power is off. (See page 22.)
The lamp operation time exceeds the time elapsed until the lamp 
shutdown. (See page 22.)
The lamp cover isn’t closed. Close the cover correctly.
Abnormal. Contact your dealer.
Steady green
or
Steady red
Blinking orange
Steady redBlinking  green
Steady greenBlinking green/red
Steady redBlinking red
Steady redSteady red
Blinking green/redOff
Blinking green/red
Steady
or
Blinking
01_ENG.fm  Page 26  Friday, May 26, 2006  4:19 PM 
						

							EN-27
ENGLISH
Specifications
 The specifications and outside appearance of the projector are subject to change without prior notice. 
Ty p e D L P ™  D ATA  p r o j e c t o r  
Model XD420U/SD420U
Rated power supply 100 - 240 V AC, 50 / 60 Hz 
Rated input 3.0 A
Display Technology0.55-inch Single chip Digital Micromirror Device (DMD) with R,G,B,W color wheel 
Pixels 1024 x 768 = 786432 pixels (XD420U) 
Pixels 800 x 600 = 480000 pixels (SD420U)
Colors 16770000 colors
Projection lens F 2.4- 2.6 f = 18 - 21.6 mm 
Light source lamp 230 W
Picture size 40 - 300 inch (aspect ratio 4:3) 
PC compatibilityResolution:640x400 (Expand) - 1024x768 (Real) - 1280x1024 (Compress) (XD420U) 
Resolution:640x400 (Expand) - 800x600 (Real) - 1024x768 (Compress) (SD420U) 
Sync on Green available
Video compatibilityNTSC / NTSC 4.43 / PAL (including PAL-M, N) / SECAM, PAL-60 
Component Video (DVD/HDTV) (480i, 576i, 480p, 576p, 1080i, 720p)
Speaker 2 W Mono, Round type ø4.5 cm x 1
S-video inputLuminance signal: 1.0 Vp-p 75 Ω (negative sync.) 
Chroma signal: 0.286 Vp-p 75 Ω (burst signal) 
Video input 1.0 Vp-p 75 Ω (negative sync.) 
Audio input 350 mVrms, 10 kΩ or more 
Analog RGB inputRGB: 0.7 Vp-p 75 Ω (negative sync.) 
YP
BPR/YCBCR : Y:1.0 Vp-p (negative sync.) PBPR/CBCR:0.7 Vp-p 
HD/CS : TTL level (positive or negative) 
VD : TTL level (positive or negative)
Control connectorSerial terminal (RS-232C) (D-SUB 9-pin) 
USB terminal (for Page Up/Down)
Outside dimensions 261 x 102 x 265 mm (width x height x depth)
Weight Approx.  2.6 kg 
Length of power cord 114 inch (1.8 m)
Temperature, humidity
(performance guaranteed)+41ºF (+5ºC) - +95ºF (+35ºC), 30 - 90% 
01_ENG.fm  Page 27  Friday, May 26, 2006  4:19 PM 
						

							EN-28
Specifications (continued)
Connectors
Dimensional drawings (unit : mm)
What’s included in the box
Replacement part
15 11
610 15
pin No.Spec.
1 R(RED)/C
R
2 G(GREEN)/Y
3B(BLUE)/C
B
4GND
5GND
6GND
7GND
8GND
9DDC5V
10 GND
11 GND
12 DDC Data
13 HD/CS
14 VD
15 DDC Clock
pin No.Spec.
1R(RED)/C
R
2G(GREEN)/Y
3B(BLUE)/C
B
4-
5GND
6GND
7GND
8GND
9-
10 GND
11 -
12 -
13 HD/CS
14 VD
15 -
COMPUTER IN/OUT (Mini D-SUB 15-pin)
IN OUT
    AC power cord
1  RGB cable for PC
1  VIDEO cablefor US 02552-0063-01
for EU 02552-0066-01
for UK 02552-0065-01
02552-0072-00
02552-0068-001  Remote control
1  Safety manual/Quick start up
1  CD-ROM
2  Battery
1 Lens cap
(Option / Not included in the box)
Spare lamp for XD420U VLT-XD420LP
Spare lamp for SD420U VLT-XD420LP
KEYSTONEENTER
VIDEOCOMPUTERAUTO POSITION
MENU
265
102
261
01_ENG.fm  Page 28  Friday, May 26, 2006  4:19 PM 
						

							EN-29
ENGLISH
Specification of RGB signals in each computer mode of the projector 
Important:
 Some computers aren’t compatible with the projector.
 The projector’s maximum resolution is 1024 x 768 pixels (800 x 
600 pixels for SD420U). It may not display images of higher reso-
lutions than 1024 x 768 (or 800 x 600) correctly.
 Images with SYNC on G (Green) signal may jitter.
 Images with SYNC on G (Green) signal may be tinged with 
green.
 If the resolution and frequency of your computer aren’t shown on 
the table, find the compatible resolution and frequency by chang-
ing the resolution of your computer.
 Set COMPUTER INPUT in the SIGNAL menu to RGB when 
inputting the HDTV signal as RGB signal. TV60 and TV50 are equivalent to 480i and 576i respectively. 
When these signals are supplied to the VIDEO or S-VIDEO sig-
nal, the signal mode is indicated as TV60 or TV50. When they are 
supplied to the COMPONENT terminal, the signal mode is indi-
cated as 480i or 576i.
Signal moderesolution
(H x V)horizontal
frequency (kHz)vertical
frequency (Hz)XD420U(H x V)SD420U
(H x V)
TV60, 480i(525i) - 15.73 59.94 1024 x 768 800 x 600
TV50, 576i(625i) - 15.63 50.00 1024 x 768 800 x 600
1080i 60 (1125i 60) - 33.75 60.00 1024 x 576 800 x 450
1080i 50 (1125i 50) - 28.13 50.00 1024 x 576 800 x 450
480p (525p) - 31.47 59.94 1024 x 768 800 x 600
576p (625p) - 31.25 50.00 1024 x 768 800 x 600
720p 60 (750p 60) - 45.00 60.00 1024 x 576 800 x 450
720p 50 (750p 50) - 37.50 50.00 1024 x 576 800 x 450
PC98 640 x 400 24.82 56.42 1024 x 640 800 x 500
CGA84 640 x 400 37.86 84.13 1024 x 640 800 x 500
CGA85 640 x 400 37.86 85.08 1024 x 640 800 x 500
VGA60 640 x 480 31.47 59.94 1024 x 768 800 x 600
VGA72 640 x 480 37.86 72.81 1024 x 768 800 x 600
VGA75 640 x 480 37.50 75.00 1024 x 768 800 x 600
VGA85 640 x 480 43.27 85.01 1024 x 768 800 x 600
SVGA56 800 x 600 35.16 56.25 1024 x 768 800 x 600
SVGA60 800 x 600 37.88 60.32 1024 x 768 800 x 600
SVGA72 800 x 600 48.08 72.19 1024 x 768 800 x 600
SVGA75 800 x 600 46.88 75.00 1024 x 768 800 x 600
SVGA85 800 x 600 53.67 85.06 1024 x 768 800 x 600
XGA60 1024 x 768 48.36 60.00 1024 x 768 800 x 600
XGA70 1024 x 768 56.48 70.07 1024 x 768 800 x 600
XGA75 1024 x 768 60.02 75.03 1024 x 768 800 x 600
XGA85 1024 x 768 68.68 85.00 1024 x 768 800 x 600
SXGA70a 1152 x 864 63.85 70.01 1024 x 768 -
SXGA75a 1152 x 864 67.50 75.00 1024 x 768 -
SXGA60b 1280 x 960 60.00 60.00 1024 x 768 -
SXGA60 1280 x 1024 63.98 60.02 960 x 768 -
MAC13 640 x 480 35.00 66.67 1024 x 768 800 x 600
MAC16 832 x 624 49.72 74.55 1024 x 768 800 x 600
MAC19 1024 x 768 60.24 75.02 1016 x 768 800 x 600
MAC21 1152 x 870 68.59 74.96 1024 x 768 -
HP75 1024 x 768 62.94 74.92 1024 x 768 800 x 600
SUN66a 1152 x 900 61.85 66.00 984 x 768 -
SUN76a 1152 x 900 71.81 76.64 984 x 768 -
01_ENG.fm  Page 29  Friday, May 26, 2006  4:19 PM 
						

							North AmericaMESCA (Mitsubishi Electric Sales Canada Inc.)
http://www.mitsubishielectric.ca
Information Technologies Group, 4299 14th Avenue,
Markham, Ontario L3R 0J2, Canada
Sales & Technical Inquires
Phone :+1-(800) 450-6487
Fax :+1-(905) 475-7958
E-mail :[email protected]
Customer Care
E-mail :[email protected]
MDEA (Mitsubishi Digital Electronics America, Inc.)
(Warranty Registration)
http://www.mitsubishi-presentations.com/
Presentation Products Division, 9351 Jeronimo Road,
Irvine, CA 92618 U.S.A
Sales & Inquires
Phone :+1(888) 307-0349 or +1(949)465-6000
E-mail :[email protected]
Technical Inquires
Phone :+1-(888) 307-0309
E-mail :[email protected]
EuropeMEU-FRA (Mitsubishi Electric Europe B.V French Branch)
25, Boulevard des Bouvets 92 741, Nanterre CEDEX,
France
Sales Inquiries
Phone :+33 (0)1 55-68-55-53
Fax :+33 (0)1 55-68-57-31
Techinical Inquireis
Phone :+33 (0)1 55-68-56-42
Fax :+33 (0)1 55-68-57-31
MEU-GER (Mitsubishi Electric Europe B.V. German Branch)
http://www.mitsubishi-evs.de/
Gothaer Strasse 8, 40880 Ratingen, Germany
Sales Inquires
Phone :0049 - 2102 - 486 9250
Fax :0049 - 2102 - 486 7320
Techinical Inquires
Phone :0049 - 2102 - 486 1330
Fax :0049 - 2102 - 486 1340
MEU-IR (Mitsubishi Electric Europe B.V. Irish Branch)
http://www.mitsubishi.ie/
Westgate Business Park, Ballymount, Dublin 24, Ireland
Sales Inquiries
Phone :+353-1-4198807
Fax :+353-1-4198890
Technical Inqiries
Phone :+353-1-4198808
Fax :+353-1-4198895
MEU-IT (Mitsubishi Electric Europe B.V. Italian Branch)
Centro Direzionale Colleoni, Palazzo Persero-Ingresso 2,
Via Paracelso 12, 20041 Agrate Brianza, Italy
Sales & Technical Inquiries
Phone :+39-(0)39-60531
Fax :+39-(0)39-6053214
E-mail :[email protected]
MEU-NL (Mitsubishi Electric Europe B.V. Benelux Branch)
http://www.mitsubishi.nl/LCD/ProdFrame.html
Nijverheidsweg 23A, 3641 RP Mijdrecht, The Netherlands
Sales Inquiries
Phone :+31-297-282461
Fax :+31-297-283936
E-mail :[email protected]
Techinical Inquiries
Phone :+31-297-282461
Fax :+31-297-283936
E-mail :[email protected]
Russia (Mitsubishi Electric Europe B.V Moscow
Representative Offi ce)
http://www.mitsubishi-projector.ru/
Moscow Representative Offi ce, 52/5 Kosmodamianskaya
Nab., 115054, Moscow, Russia
Sales & Techinical Inquiries
Phone :(7095) 721-2068
Fax :(7095) 721-2071
MITSUBISHI Projector Contact Information
MITSUBISHIELECTRIC CORPORATION
INDONESIA (Mitsubishi Electric Asia Pte. Ltd.)
307, Alexandra Road, #05-01/02 Mitsubishi Electric
Building, Singapore 159943
Sales Inqiries
Phone :+65-6473-2308
Fax :+65-6475-9503
E-mail :[email protected]
Technical Inquiries
Phone :+65-6470-2666
Fax :+65-6475-9503
PHILLIPINES (Mitsubishi Electric Asia Pte. Ltd.)
http://www.mitsubishielectric.com.sg
307, Alexandra Road, #05-01/02 Mitsubishi Electric
Building, Singapore 159943
Sales Inquiries
Phone :+65-6473-2308
Fax :+65-6475-9503
E-mail :[email protected]
Technical Inqiries
Phone :+65-6470-2666
Fax :+65-6475-9503
VIETNAM (Mitsubishi Electric Asia Pte. Ltd.)
307, Alexandra Road, #05-01/02 Mitsubishi Electric
Building, Singapore 159943
Sales Inquiries
Phone :+65-6473-2308
Fax :+65-6475-9503
E-mail :[email protected]
Technical Inquiries
Phone :+65-6470-2666
Fax :+65-6475-9503
STC (Setsuyo Astec Corporation Seoul Branch)
4F,Dongseo Game Channel Bldg,660-11 Deungchon-Dong,
Kangseo-Ku, Seoul, Korea
Sales & Technical Inqiries
Phone :+82-(0)2-2657-9841~3
Fax :+82-(0)2-2657-9900
MALAYSIA (Antah Melco Sales & Services Sdn. Bhd.)
6, Jalan 13/6 46860 Petaling Jaya Selangor, Darul Ehsan,
Malaysia
Sales & Technical Inquiries
Phone :+60-(0)3-79552088 (Ext. 203)
Fax :+60-(0)3-79563950/+60-(0)3-79582576
Technical & Service Inquiries
Phone :+60-(0)3-79552088 (Ext. 106)
Fax :+60-(0)3-79563950/+60-(0)3-79582576
ME-TWN (Mitsubishi Electric Taiwan Co., Ltd.)
http://www.mitsubishi-kyw.co.th/
11TH FL., 88 SEC. 6, CHUNG SHAN N. RD., TAIPEI, 111R.
O.C.
Sales & Technical Inquires
Phone :+886-2-2832-8255
Fax :+886-2-2833-9813
MKY (Mitsubishi Electric Kang Yong Watana Co., Ltd. )
http://www.mitsubishi-kyw.co.th/
Road, Huamark Bangkapi, Bangkok 10240, Thailand
Sales & Technical Inquiries
Phone :+66-2-731-6841
Fax :+66-2-379-4763
OceaniaME-AUST (Mitsubishi Electric Australia)
http://www.mitsubishi-electric.com.au/prod.asp?prod=proj
348 Victoria Road, Rydalmere, N.S.W. 2116, Australia Sales
& Technical Inqiries
Phone :+(612)9684-7777
Fax :+(612)9684-7208
E-mail :[email protected]
Technical Inquiries
Phone :+(612)9684-7694
Fax :+(612)9684-7684
E-mail :[email protected]
BDT (Black Diamond Technologies Ltd.)
(Warranty Registration) http://www.bdt.co.nz/projectors/
warranty.asp
1 Parliament St, Lower Hutt, Wellington, New Zealand Sales
Inquiries
Phone :+64-(0)4-560-9100
Fax :+64-(0)4-560-9133
E-mail :[email protected]
Technical Inquiries
Phone :+64-(0)4-560-9100
Fax :+64-(0)4-560-9133
E-mail :[email protected] MEU-SP (Mitsubishi Electric Europe B.V. Spanish Branch)
http://www.mitsubishielectric.es/
Ctra. de Rubi, 76-80, 08173 Sant Cugat del Valles,
Barcelona, Spain
Sales Inquiries
Phone :+34-93.565.31.54
Fax :+34-93.589.43.88
E-mail :[email protected]
Technical Inquiries
Phone :+34-93.586.27.51
Fax :+34-93.588.53.87
E-mail :[email protected]
MEU-SWE (Mitsubishi Electric Europe B.V Scandinavian
Branch)
Hammarbacken 14, Box 750, S-19127, Sollentuna, Sweden
Sales Inquiries
Phone :+46-(0)8-6251070
Fax :+46-(0)8-6251036
Technical Inquiries
Phone :+46-(0)8-6251052
Fax :+46-(0)8-6251036
MEU-UK (Mitsubishi Electric Europe)
http://www.mitsubishi.co.uk/evs/
Visual Information Systems Division, Travellers Lane,
Hatfi eld, Hertfordshire, AL10 8XB U.K.
Sales Inqiries
Phone :+44 (1707) 278684
Fax :+44 (1707) 278541
E-mail :[email protected]
Technical Inquiries
Phone :+44 (870) 606 5008
Fax :+44 (1506) 431927
E-mail :[email protected]
AsiaCHINA (Mitsubishi Electric Air-Conditioning & Visual
Information Systems (Shanghai) Ltd.)
26/F .,Oriental Center ,699 Nanjing Rd(W),Shanghai,
200041,China
Sales Inquiries
Phone :+86(21) 5211-0882-3022
Fax :+86(21) 5211-0576
Technical Inquiries
Phone :+86(21) 5211-0882-3020
Fax :+86(21) 5211-0576
HONG KONG (Mitsubishi Electric Ryoden Air-Conditioning
& Visual Information Systems (HongKong) Ltd.)
7th Floor, Manulife Tower, 169 Electric Road, North Point,
Hong Kong
Sales Inquiries
Phone :+852-2510-1505
Fax :+852-2510-0463
Technical Inquiries
Phone :+852-2422-0161
Fax :+852-2487-0181
SINGAPORE (Mitsubishi Electric Asia Pte. Ltd.)
http://www.mitsubishielectric.com.sg
307, Alexandra Road, #05-01/02 Mitsubishi Electric
Building, Singapore 159943
Sales Inquiries
Phone :+65-6473-2308
Fax :+65-6475-9503
E-mail :[email protected]
Technical Inquiries
Phone :+65-6470-2666
Fax :+65-6475-9503
INDIA (Mitsubishi Electric Asia Pte. Ltd.)
307, Alexandra Road, #05-01/02 Mitsubishi Electric
Building, Singapore 159943
Sales Inquiries
Phone :+65-6473-2308
Fax :+65-6475-9503
E-mail :[email protected]
Technical Inquiries
Phone :+65-6470-2666
Fax :+65-6475-9503
1 Zusho Baba, Nagaokakyo-City, Kyoto Japan
01_ENG.fm  Page 30  Friday, May 26, 2006  4:19 PM