Mitsubishi Sd200u Projector User Manual

							EN – 11
ENGLISH
COMPUTER OUTCOMPUTER 2 / COMPONENT IN
COMPUTER 1 IN
COMPUTER
AUDIO IN
VIDEO 1 
INVIDEO 2 
IN
S-VIDEO
VIDEO
AUDIO
AC INAUDIO OUTMAIN
MOUSE /RS-232C
AUDIO OUT
MONITOR OUTPUT
to COMPUTER (1or2) IN
to  AUDIO INto monitor port
to  COMPUTER 
OUT
to PC audio
output
Audio cable (option)
When outputting to both a 
PC monitor and the projector.RGB cable for PC
RGB cable for PC (option)
computer
Projector + Personal computer
Important:
•When you use a long RGB cable instead of the cable provided, the picture quality may deteriorate.
•Connectors or analog RGB output adapters may be necessary depending on the PC connected to this projector.
Please contact your dealer.
•The audio input for this projector is a stereo pin jack.  (Speaker output is mono.)  Please check the available
cable for the audio input terminal of the PC.  Some personal computer may not have the audio output terminal.
For using Macintosh
•A monitor output adapter is necessary for a Macintosh if it has no video port. Please contact your dealer.
•A MAC adapter for RGB cable may be necessary depending on the personal computer connected to this projec-
tor.  Please contact your dealer.
About DDC™ (For COMPUTER 1 IN connector)
The projector complies with VESA™ DDC™ 1/2B (EDID) specification. If your computer provides DDC™ 1/2B (EDID)
function,  setup will be done automatically. If your system is Windows
® 98 or higher, your computer supported in
standard. If your system is Windows® 95 or lower, you must down load the driver from our Internet Home Page for use
this function. Please contact your dealer or Mitsubishi sales office for more details. 
						

							EN – 12
Front adjustment feet Screen
Preparing the projector for operation
Getting ready for projection
1. Connect the power cord provided to the projector.
2. Connect the power cord to the wall power outlet.
3. Remove the lens cap.
Warning:
•Do not look directly into the lens when projector is
“ON”.
•The lens cap is for protecting the lens.  If you leave
the power on with the cap on, the cap may be warped.
Please remove the lens cap when you turn the power
on.
•This projector is equipped with the power cords for
both U.S. and Europe.  Use the appropriate power
cord for your country.
•A three-pin grounding type power plug is used with
the projector. Do not remove the grounding pin on
the power plug. If you are unable to insert the plug
into the outlet, contact your electrician to replace
your A/C outlet.
•The supplied power cord for U.S. is used for 120V
only. Never connect to any outlet or power supply
having a different voltage or frequency. If you
connect to the power supply having a different
voltage, please use the appropriate power cord.
•Use 100-240V AC 50/60Hz correct voltage other-
wise it may lead to fire or electric shock.
•Do not place any objects on the power cord, and keep
the projector away from heat sources to avoid break-
ing the power cord. A broken power cord can cause
fire or electric shock.
•Do not revise or alter the power cord otherwise it
may cause fire or electric shock.
Contact your dealer if the cord is broken.
Caution:
•Plug in firmly and unplug by holding the plug, not
by pulling the cable out.
•Do not plug in or out with wet hands.  It may cause
an electric shock.
Adjusting the angle of projection
For the best result, project onto a flat screen with a 90
degree angle to the floor. If necessary, tilt the projector
by adjusting the adjustment feet on the bottom of the
projector.
1. Lift the projector to an appropriate angle.
2. Press the foot adjustment buttons, and the front
adjustment feet will slide out to their appropriate
positions.
3. Release the foot adjustment buttons to fix the feet
in those positions.
4. Turn the feet for fine adjustment.
•The projection angle can be adjusted by turning
the rear adjustment feet.
After using the projector
5. Put the front adjustment feet back into the projector.
Important:
•When the screen or projector is not placed flatly,
the projected image becomes distorted to shape a
trapezoid. When the image shape isn’t corrected
even after adjusting the projector and the screen,
adjust the widths of the top and bottom of the
image to be equal by pressing the KEYSTONE +
or - button.  When adjusting by the remote control,
press the KEYSTONE button to display the
“KEYSTONE CORRECTION” menu first, and
adjust the widths by pressing the + or - button.
•Screen on a flat wall with a 90˚ angle to the floor.
•Align projector to produce a full screen display as
illustrated on page 9.
•The distance from the projector to the screen must
be compatible with screen size chart on page 9.
Note the distance from the screen chart.
Front adjustment 
feetFoot adjustment
buttons 
						

							EN – 13
ENGLISH
To operate projector power ON
• The picture might not be of optimum performance
in extreme hot or cold conditions. (The projector is
not malfunctioning.)
4.  Select the desired external input source by using
the COMPUTER or VIDEO button.
• The COMPUTER or VIDEO button does not work
when MENU is displayed. At this time, the prohibi-
tion mark (
) appeares on the screen.
• The projector automatically selects the appropriate
signal format. The selected signal format is dis-
played on the screen.
• When selecting the COMPUTER input, the image
may  flicker.  Press the $ or % button to adjust the
image.
5.   Adjust the image size with the zoom ring by
turning it.
6. Adjust the focus with the focus ring by turning it. 1. Turn on the equipment connected to the projector.
2. Put the projector into standby mode by pressing the
main power switch. The POWER indicator lights up
red.
3. Turn the projector on by pressing the POWER but-
ton. The light source lamp starts warming up, even-
tually turning completely on.
• When the light source lamp does not light up,
wait until the STATUS indicator is turned off,
then press the POWER button again.
• If the main power switch to the unit is turned
off within two minutes of turning off the light
source lamp, power will not be applied to the
lamp for one minute when the next time the
main unit power switch is turned on. When
this happens, the STATUS indicator will blink
for one minute.
ConditionIndicator
STATUSPOWER
Stand-by
-Red
When light source lamp is onGreen
Green
Light source lamp held off temporarilyRed-
Important:
• A darkened image may be seen right after pressing
the POWER button due to warming up of this pro-
jector. While warming up, no other commands can
be accepted.
• After the power is turned on, the screen may flicker
before the lamp operation becomes stable. This is
due to the characteristics of the lamp, not a failure
of the lamp.
• When the STATUS indicator is blinking red, the
lamp should be replaced.  Replace the lamp. See
pages 22 and 23           .
COMPUTER OUTCOMPUTER 2 / COMPONENT IN
COMPUTER 1 IN
COMPUTER
AUDIO IN
VIDEO 1 
INVIDEO 2 
IN
S-VIDEO
VIDEO
AUDIO
AC INAUDIO OUTMAIN
MOUSE /RS-232C
COMPUTER
POWER POWER
LAMP/TEMP
STATUS
VIDEOAUTO
POSITION
+
–
2  •  9
AUTO POSITION
buttonMUTE button
3 • 7 • 8
4
POWER MUTE
COMPUTERVIDEO
MOUSE LASER
MENU
ENTER / STILL
R-CLICK
AUTO POSITIONPinP
KEYSTONE EXPAND
KEYSTONE–+
VOLUME –+
3 • 7 • 8
4
AUTO POSITION button
KEYSTONE
wide
zoom ring
telefar
near
focus ring 
						

							EN – 14
To operate projector power ON (Continue)
Turning off the projector
7. Press the POWER button.
The message “POWER OFF? YES : PRESS AGAIN”
appears on the screen.
8. Press the POWER button within 10 seconds again.
•The light source lamp will be turned off.
•When the POWER button is not pressed within 10
seconds, the message will be disappeared.
•Pressing the POWER button second time  will shut
off the light source lamp, but the exhaust fan con-
tinues to operate for 120 seconds to cool down the
light source lamp.
9. Turn off the main power switch. When turning off
the main switch, the POWER indicator turns off.
•In cases where the main power switch is acciden-
tally turned off when either the intake/exhaust
fan or the power source lamp is in operation, allow
the unit to cool down for 10 minutes with the
power turned off. Repeat step 3 when turning on
the power source lamp. If the lamp does not turn
on immediately, repeat this step two or three
times. Replace the lamp if it should still fail to
turn on.
AUTO POSITION button
When the source is selected to COMPUTER and the
image is not in the right place, follow as shown below.
1. Set screen to the brightest display as possible
(e.g., full-screen display of the “Tr a s h” window).
2. If the screen saver is running, turn off the screen saver.
3. Press the AUTO POSITION button.
•If the image is still not in the right place, adjust
the image position by using the SIGNAL menu.
The volume from the speaker
Press the VOLUME + or – button to change the volume
from the speaker.
The volume control bar will appear on the screen.
•The volume control bar will disappear about 4
seconds after releasing the volume buttons.
•The volume buttons do not work when MENU
selection bar or MENU is displayed.
•The volume from the AUDIO OUT jack is also
changed by pressing the VOLUME + or – button on
the remote control.AV mute
Image and audio are temporarily erased with press-
ing the MUTE button. To restore the image and
audio to the normal mode, press the MUTE button
again.
•The audio from the AUDIO OUT jack is also muted
by pressing the MUTE button.
Caution:
•When you have finished using this equipment, wait
120 seconds for the exhaust fans to stop. Then turn
off the main switch and unplug the power cable from
the wall outlet, for safety purposes.
•After the lamp is turned off,  the lamp cannot be
switched on again for 60 seconds as a precaution-
ary measure. It will take another 60 seconds before
the STATUS indicator goes off. If you wish to turn
on the projector again, wait until the indicator is off
then press the POWER button.
•The exhaust fan rotates faster when the tempera-
ture around the projector rises.
•When the temperature around the projector becomes
too high, the sign  “TEMP!!” blinks red on the screen.
If the temperature stays too high, the lamp will be
shut off automatically. 
						

							EN – 15
ENGLISH
Basic operation
Several settings can be adjusted using Menu.
EXAMPLE: Auto power off time setting
1.  Press the MENU button.
2.  Press the $ or % button to select the INSTALLA-
TION menu.
3.  Press the ENTER button (or } button).4.  Press the { or } button to select AUTO POWER
OFF.
5.  Press the $ or % button to adjust auto power off
time.
6.  Exit the menu system by pressing the MENU but-
ton several times.
• If the menu operation is not working, turn off the
main power, wait about 10 minutes, and turn on the
main power again.
• The settings with 
 mark, you should press the
ENTER button after selecting.
Menu operation
opt.
IMAGE
TV60
opt.
INSTALLATION
TV60
opt.
INSTALLATION
TV60
AUTO POWER
ON
AUTO POWER
OFFOFF
OFF
AUTO POWER
ON
AUTO POWER
OFFOFF
OFF
AUTO POWER
ON
AUTO POWER
OFFOFF
30min
IMAGE CONTRAST± 20BRIGHTNESS± 20sRGB ON, OFFVIDEOCOLOR MATRIX
COLOR± 10TINT
± 10
SHARPNESS± 5RED± 30
CYAN± 30GREEN± 30YELLOW± 30
BLUE± 30MAGENTASATURATION± 30
± 10CONTRAST R± 15CONTRAST B± 15BRIGHTNESS R± 15BRIGHTNESS B± 15
EXPAND MODE
EXPAND, REALUPPER LEFT, LOWER RIGHT
INSTALLATION
IMAGE REVERSE
OFF, MIRROR, INVERT, MIRROR INVERT
AUTO POWER ON ON, OFF
ON, OFFAUTO POWER OFF
1 - 4
FEATURE MENU POSITION
OFF, 5, 10, 15, 30, 60 minSPLASH SCREENBLUE, BLACKBACK COLOR
VIDEO SIGNAL
VIDEO MODEAUTO, OFFCINEMA MODEAUTO, NTSC, PAL, SECAM, 4.43NTSC, PAL-M, PAL-N, PAL-60LANGUAGE
RESET ALL
SIGNALHORIZ.POSITION 0 - 999VERT.POSITION 0 - 999TRACKING 0 - 9999
COMPUTER INPUT
USERON
OFFCLAMP POSITION0 - 127CLAMP WIDTH 0 - 63
SHUTTER (L)
0 - 20
0 - 20
0 - 20SHUTTER (U)
0 - 20VERT.SYNC
AUTO, OFF
COMPUTER
USER
OFFSTANDARDLOWCOLOR TEMP
USER 
*3
*3
*3
*3 *4
*4
FINE SYNC. 0 - 31*4
*4
*4
*4 *1
*2,*5
*5
*5
*5
*5,*6
*5
*3
HOLD
OK
BEGIN 0 - 15END 0 - 15
ANAMORPHICRGB, YCBCR / YPBPR
* 1: The item can not be selected when the sRGB is set to ON.
* 2: The item can not be selected with certain signals.
* 3: Setting range is different with certain signals.
* 4: The item can not be selected when the source is selected
       VIDEO or S-VIDEO.
* 5: The item can not be selected when the source is selected 
       to COMPUTER.
* 6: The item can not be selected when the VIDEO MODE is 
       not set to 1.  
, English, Español, Deutsch, Français, Italiano, 
SHUTTER (RS)SHUTTER (LS)
OK
ON, OFFHIGH 
						

							EN – 16
MENU POSITIONUPPER LEFT
EXPAND MODEEXPAND
VIDEO MODE
1
CINEMA MODE
VIDEO SIGNAL
AUTO
LANGUAGE
English
RESET ALLOK
Opt
FEATURE
AA
AË ?
TV60
AUTO
opt.
INSTALLATION
TV60
ON
AUTO POWER
ON
AUTO POWER
OFF
SPLASH
SCREEN
BACK COLOR
IMAGE
REVERSEOFF
OFF
OFFON
BLUE
CONTRAST
sRGBBRIGHTNESS
COLOR MATRIX
COLOR TEMP
COLORTINT
SHARPNESS0
0 0
0 0
OFF
OFF
STANDARD
opt.
IMAGE
TV60
Menu operation (continued)
1 IMAGE
CONTRAST ........Adjusts the picture contrast. The contrast becomes
higher as the number increases.
BRIGHTNESS ....Adjusts the image brightness. The image becomes
brighter as the number increases.
sRGB ................... Select ON to display an image emphasizing on the color
reproducibility.
•When sRGB is ON, COLOR MATRIX can’t be ad-
justed.
•When sRGB is ON, the image will become darker.
•When COLOR TEMP. is set to other than STAN-
DARD while sRGB is ON, colors won’t be reproduced
as per the standard value of sRGB.
•Though sRGB can be ON while a signal is input from
VIDEO-IN or S-VIDEO IN, reproduced colors won’t
be in accordance with the sRGB standard value.  Use
sRGB to suit your color preference.
COLOR MATRIX .......Adjusts the color balance in each color of the image. See page 18.
COLOR TEMP. ... Adjusts the color temperature. See page 18.
TINT ....................Adjusts the color balance of the image. The color balance of the image shifts green as the
number increases and shifts to purple as the number decreases. (Available only when
VIDEO is selected as the source.)
•TINT cannot be adjusted when a TV50 (PAL or SECAM) signal is being displayed.
COLOR ................Adjusts the color intensity of the image. (Available only when VIDEO is selected as the
source.)
SHARPNESS ...... Adjusts the image sharpness. The image sharpness rises as the number increases.
2 INSTALLATION
AUTO POWER ON ....Select ON to boot up the projector automatically by
turning on an externally connected power switch such as
a breaker even when the main power switch of the
projector is off. Use this setting when the projector is
hanging from the ceiling.
•The projector will be in the stand-by mode when the
lamp is off.  Use the remote control to turn on the
lamp.
AUTO POWER OFF ..Set the time elapsed before the projector enters into the
stand-by mode when there is no signal present at the
selected source.
SPLASH SCREEN .....Select ON to display the splash screen when the power is
turned ON.
BACK COLOR ....Select the color of the background to blue or black, this will be displayed when there is no
signal present at the selected source.
IMAGE REVERSE .....Use to reverse or invert the projected image. Select MIRROR in rear projection. Select
MIRROR, INVERT in rear projection with the projector hanging from the ceiling.
3 FEATURE
MENU POSITION .....Use to select the position of the menu on the screen,
UPPER LEFT or LOWER RIGHT.
EXPAND MODE ..Select the mode for enlarging screen. See page 20.
VIDEO MODE .... Use to select the modes of the high quality line doubler.
Select 1 for the Cross Color Suppression mode. Select 2
for DCDi mode. Select 3 for normal high quality line
doubler mode. Select 4 for through mode.
•Though square-shaped noise may appear in the
projected image when 1 is selected, this is not failure.
If it is obtrusive, select other positions than 1.
•A playback signal on a deteriorated videotape or a
poor-quality signal may not be projected properly.
When projecting such a signal, change the setting of
the Video mode and check the projection quality. 
						

							EN – 17
ENGLISH
CLAMP 
POSITION
opt.XGA60
SIGNAL
SIGNAL - USER
0
CLAMP WIDTH0
VERT.SYNCAUTO
SHUTTER (U)0
SHUTTER (L)0
SHUTTER (LS)0
SHUTTER (RS)0
CLAMPCLAMP
CLAMPCLAMP
?
HORIZ.POSITION
opt.XGA60
SIGNAL
R G BR G B
VERT.POSITION
TRACKING
FINE SYNC
COMPUTER
INPUT
HOLDANAMORPHIC
USER0
0
0
0
RGB
OFFON
OK
CINEMA MODE .. When ON is selected, the film mode will be automatically activated when a film source signal
is inputted. When OFF is selected, the film mode will not be activated.
VIDEO SIGNAL ... When AUTO is selected, the appropriate video format is automatically selected depending
on the input signal. If the image isn’t displayed correctly, select the desired video format
manually.
LANGUAGE ....... Use to select the language used in the menus. (
 / English / Español / Deutsch / Français
/ Italiano / 
)
RESET ALL ........ Use to reset the MENU settings (except LANGUAGE).
4 SIGNAL
HORIZ. POSITION ....Use to adjust the horizontal position of the image.
VERT. POSITION .....Use to adjust the vertical position of the image.
TRACKING ......... Use to avoid image noise such as wide stripes.
FINE SYNC. ....... Use to synchronize the projector with PC input signals
so that the image is not blurred.
COMPUTER INPUT......This will be set automatically to match the input signal
to component video (YC
BCR/YPBPR) or RGB. This can be
overridden as required.
ANAMORPHIC ... Select ON when playing DVD discs containing data of
widescreen images.
HOLD .................. Adjusts the image when flagging occurs near the top of
the screen.
5 SIGNAL - USER (Normally, there is no need for adjustments.)
CLAMP POSITION/
CLAMP WIDTH .........
If you use something similar, the brighter colors of the
projected image may become blurred. In this case,
adjust CLAMP POSITION or CLAMP WIDTH.
VERT. SYNC ......Use to adjust the image when its motion does not run
smoothly.  Select AUTO for normal setting.
SHUTTER(U) ..... Use to adjust the image when the noise etc. appears on
top part of image.
SHUTTER(L) ...... Use to adjust the image when the noise etc. appears on
bottom part of image.
SHUTTER(LS) .... Use to adjust the image when the noise etc. appears on
left side of image.
SHUTTER(RS) ... Use to adjust the image when the noise etc. appears on
right side of image. 
						

							EN – 18
Adjusting the image
You can adjust the picture by using the IMAGE menu.
To control the level of white-to-black in the image :
Adjust CONTRAST in the IMAGE menu.  Press the
% button to increase the contrast and the $ button
to reduce it.
To control the light level of the image :
Adjust BRIGHTNESS in the IMAGE menu.  Press
the % button to lighten the image and the $ button
to darken the image.
To adjust the red-green color balance of the image :
Adjust TINT in the IMAGE menu.  Press the %
button to increase the amount of red in the image
and the $ button to increase the amount of green in
the image.
To determine the intensity of the color :
Adjust COLOR in the IMAGE menu.  Press the %
button to increase the amount of color in the image
and the $ button to decrease it.
To adjust the detail and clarity of the image :
Adjust SHARPNESS in the IMAGE menu.  Press the
% button to make the picture seem sharper and the
$ button to make it softer.
Color matrix
This feature adjusts the color balance of the primary
colors (red, green, blue), and secondary colors (yellow,
cyan, magenta). You can use the color matrix adjust-
ment to emphasize a specific color without changing
the appearance of any of the other colors.
1.  Select COLOR MATRIX in the IMAGE menu.
2.  Press the $ or % button to select USER
 .
3.  Press the ENTER button.
Picture adjustment
CONTRAST R0
CONTRAST B0
BRIGHTNESS R0
BRIGHTNESS B0
COLOR TEMP.- USER
CONTRAST
sRGBBRIGHTNESS
COLOR MATRIX
COLOR TEMP
COLORTINT
SHARPNESS0
0 0
0 0
OFF
OFF
STANDARD
opt.
IMAGE
TV60
About color temperature
The appearance of white can be affected by adjusting the
color temperature. With low color temperature, white
appears reddish and with high color temperature white
appears to become more bluish. The color temperature
can be manually controlled by adjusting the red and
blue contrast level.
To set the color temperature high:
Set the contrast B (Blue) to a high number and the
contrast R(Red) to a low number.
To set the color temperature low:
Set the contrast B (Blue) to a low number and the
contrast R(Red) to a high number.
4.  Press the { or } button to select the desired color.
•If you wish to adjust the color intensity of the
image, select SATURATION.
5.  Press the $ or % button to adjust the color balance
of the color.
6. Repeat steps 4 and 5 for more adjustments.
7. Exit the menu system by pressing the MENU but-
ton several times.
•When using the setting which has been already
prepared, select desired position VIDEO or COM-
PUTER in step 2.  When the source is selected to
VIDEO or S-VIDEO, VIDEO will be selected auto-
matically. When the source is selected to COM-
PUTER, COMPUTER will be selected automati-
cally.
•When not using Color matrix adjustment, select
OFF in step 2.
Color temperature
1.  Select COLOR TEMP. in IMAGE menu.
2.  Press the $ or % button to select USER
.
3.  Press the ENTER button.
4.  Press the { or } button to select the desired item.
5.  Press the $ or % button to adjust the item.
6. Repeat steps 4 and 5 for more adjustments.
7. Exit the menu system by pressing the MENU but-
ton several times.
RED0
YELLOW0
GREEN0
CYAN0
BLUE0
MAGENTA0
SATURATION0
COLOR MATRIX 
						

							EN – 19
ENGLISH
Adjustment from personal computer
This projector should automatically display the full
computer image on the projection screen. However,
with some computers signals this may not occur, in
this case press the AUTO POSITION button. If the
images are still not projected correctly, use the
MENU display to adjust the projected images.
HORIZ.POSITION
opt.XGA60
SIGNAL
R G BR G B
VERT.POSITION
TRACKING
FINE SYNC
COMPUTER
INPUT
HOLDANAMORPHIC
USER0
0
0
0
RGB
OFFON
OK
Top part of image curves :
Change the setting of HOLD in the SIGNAL menu.
Select ON
,  press the ENTER buttun and adjust
BEGIN or END for image which top part is the least
curved.
Image does not move naturally :
Adjust VERT. SYNC of the menu in the SIGNAL -
USER menu.  Select AUTO for normal setting.
• Do not change any other items in the SIGNAL -
USER menu for normal operation.
Simple adjustment method
1. Select HORIZ. POSITION in SIGNAL menu.
2. Press the$ or % button to adjust the horizontal
start position (the left side of image).
3. Select TRACKING in SIGNAL menu.
4. Press the$ or % button to adjust the horizontal
end position (the right side of image).
5. Repeat steps 1 to 4 for fine adjustment.
6. Select VERT. POSITION in SIGNAL menu.
7. Press the$ or % button to adjust the vertical
start position (the top end of image).
CLAMP 
POSITION
opt.XGA60
SIGNAL
SIGNAL - USER
0
CLAMP WIDTH0
VERT.SYNCAUTO
SHUTTER (U)0
SHUTTER (L)0
SHUTTER (LS)0
SHUTTER (RS)0
CLAMPCLAMP
CLAMPCLAMP
?
Wide stripes appear :
Adjust CLAMP POSITION or CLAMP WIDTH in
the SIGNAL - USER menu.
Noise appears on right or left side of image :
Adjust SHUTTER (LS), SHUTTER (RS) in the
SIGNAL - USER menu.
Noise etc. appears on top or bottom part of image :
Adjust SHUTTER (U), SHUTTER (L) in the SIG-
NAL - USER menu. Image moved to right or left :
Adjust HORIZ. POSITION in the SIGNAL menu.
Press the % button to move the image to left.  Press
the $ button to move the image to right.
Image moved to up or down :
Adjust VERT. POSITION in the SIGNAL menu.
Press the % button to move the image to upward.
Press the $ button to move the image to down.
Image flickers / Image is slightly blurred :
Adjust FINE SYNC. in the SIGNAL menu. 
						

							EN – 20
Advanced features for presentation
Expand
By pressing the EXPAND button on the remote con-
trol, you can magnify the detailed image of the picture.
Using the Expand mode
1. Press the EXPAND button.
• You can magnify different areas of the active pic-
ture by pressing the {, }, $, % button.
• You can change the magnification of the zoomed area
by pressing the + or - button.
2. Press the EXPAND button on the remote control
again.
The normal screen display will appear on the screen.
• Display enlargement does not work with
video input or S-video input.
• The EXPAND mode will not work with certain sig-
nals.
REAL screen display
You can view the screen displaying the picture as its
original size (native resolution display).
Setting the Expand mode for REAL screen
display
1. Press the MENU button.
2. Press the $ or % to select the Feature menu.
3. Press the ENTER button.
4. Press the  { or } button to select Expand Mode.
5. Press the $ or % to set the EXPAND to REAL.
Native resolution
 display
(EXPAND )(REAL)
Zooming
image
Expand Mode
6. Press the MENU button twice to exit the menu sys-
tem.
Viewing the REAL screen display
1. Press the EXPAND button.
2. Exit the REAL mode, by pressing the EXPAND but-
ton again.
The normal screen display will appear on the screen.
• Display enlargement does not work with
video input or S-video input.
•During REAL mode, Press the $ or % buttons
for fine adjustment.
•During REAL mode, the { and } buttons are
not working. At this time, the prohibition mark
(
) appeares on the screen.
•The expanding rate cannot be changed by press-
ing either the + or - button. They are working for
volume adjustment.
Picture in Picture (PinP)
One of the special features of this unit is the picture-
in-picture (PinP) mode. PinP allows you to view differ-
ent sources at the same time.
Using the PinP mode
1. Press the PinP button on the remote control.
When the image from the COMPUTER IN termi-
nal is displayed on the screen, the image from
VIDEO IN or S-VIDEO IN terminal is displayed as
sub-image.
•You can change the input source of the sub image
by pressing the VIDEO button.
•When the COMPUTER button is pressed, the input
source of the main image will be changed and the
sub image will disappear.
•When the image from the VIDEO IN or S-VIDEO
IN terminal is displayed on the screen, the PinP will
not work.
•The PinP mode will not work with certain signals.
To change frame position
2. Press the $ or % buttons on the remote control.
3. Press the PinP button on the remote control again.
The sub image will disappear.
•In PinP mode, the audio of the Main image is
output.
•In PinP mode, if the signal of the Main image is
lost, the sub image will disappear.
Still
How to stop the picture temporarily (still picture).
1. Press the STILL button on the remote control.
The picture will be freezed temporary.
To resume picture activity.
2. Press the STILL button on the remote control
again.