Mitsubishi Sa51u Projector User Manual

							4
ITEM ASCII HEX VALUE
AUTO POWER ON APON 41h 50h 4Fh 4Eh0 (OFF), 1 (ON)
AUTO POWER OFF APOF 41h 50h 4Fh 46h00 (Off) , 05, 10, 15, 30, 60
IMAGE REVERSE IR 49h 52h0 (OFF), 1 (Mirror), 2 (Invert), 3 (Mirror invert)
MENU POSITION MP 4Dh 50h0 (Upper left), 1 (Lower right)
EXPAND MODE EX 45h 58h1 - 2
AUDIO MODE AU 41h 55h1 (COMPUTER), 2 (VIDEO), 3 (COMPUTER & VIDEO)
VIDEO SIGNAL VS 56h 53h0 (AUTO), 1 (NTSC), 2 (PAL), 3 (SECAM) ,
4 (4.43NTSC),  5 (PAL-M), 6 (PAL-N), 7 (PAL-60)
ANAMORPHIC SC 53h 43h0 (OFF), 1 (ON)
LANGUAGE LG 4Ch 47h0 (
), 1 (English), 2 (Español), 3 (Deutsch) ,
4 (Frençais),  5 (Italiano), 6 ()
RESET ALLRSTALL52h 53h 54h 41h 4Ch 4Ch
MEMORY CALL MMC 4Dh 4Dh 43h0 (AUTO), 1 (USER1), 2 (USER2)
HORIZ. POSITION HP 48h 50h+ (increase), – (decrease)
VERT. POSITION VP 56h 50h+ (increase), – (decrease)
FINE SYNC. FN 46h 4Eh00 - 39
TRACKING TRK 54h 52h 4Bh+ (increase), – (decrease)
COMPUTER INPUT CIN 67h 49h 4Eh0 (RGB), 1 (YCBCR/YPBPR)
HOLD HLD 48h 4Ch 44h0 (AUTO), 1 (ON), 2 (OFF)
HOLD BEGIN HLB 48h 4Ch 42h–01 - –99
HOLD END HLE 48h 4Ch 45h01 - 99
CLAMP POSITION CLP 43h 4Ch 50h00 - 63
CLAMP WIDTH CLW 43h 4Ch 57h01 - 63
HORIZ. PIXELS HPL 48h 50h 4Ch0000 - 9999
VERT LINES VLN 56h 4Ch 4Eh0000 - 9999
PLL PLL 50h 4Ch 4Ch0 (AUTO), 1 (0), 2 (1), 3 (2), 4 (3), 5 (4), 6 (5), 7 (6), 8 (7)
VERT.SYNC VSC 56h 53h 43h0 (AUTO), 1 (ON), 2 (OFF)
SHUTTER (U) SHU 53h 48h 55h000 - 299
SHUTTER (L) SHL 53h 48h 4Ch000 - 299
SHUTTER (LS) SHLS 53h 48h 4Ch 53h000 - 398
SHUTTER (RS) SHRS 53h 48h 52h 53h000 - 398
How to set the grade
Use ASCII letters code to set the grade for setting data. Please refer to the table below for HEX code.
ASCII + – 0 1 2 3 4 5 6 7 8 9
HEX 2Bh 2Dh 30h 31h 32h 33h 34h 35h 36h 37h 38h 39h
[Example 1] Set the AUTO POWER ON to ON.
[Example 2] Set the difference data of R from G to +10, the setting main data to 0 and the difference data of
B from to -5.
Sending commands Status code from Meaning
from the PC etc. projector
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D Command for setting the
0 0 P + 1 0 + 0 0 - 0 5 
 picture control
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D Command received
0 0 P + 1 0 + 0 0 - 0 5 
 (Command echo back)
Sending commands Status code from Meaning
from the PC etc. projector
30 30 41 50 4F 4E 30 0D Command for setting the
0 0 A P O N 1 
 AUTO POWER ON to ON
30 30 41 50 4F 4E 30 0D Command received
0 0 A P O N 1 
 (Command echo back)
The data code of CONTRAST and BRIGHTNESS is structured by the difference data of R from G, the main data and the difference
data of B from G.
[Example 3] The TINT was set to +10 when the setting status was confirmed.
Sending commands Status code from Meaning
from the PC etc. projector
30 30 53 0DCommand to confirm
0 0 S 
setting of TINT
30 30 53 2B 31 30 0D Command (setting of TINT
0 0 S + 1 0 
 is +10) carried out