Mitsubishi S50u Projector User Manual

							«EN Ð 11
ENGLISH
Connection
For IBM PC or IBM PC compatibles
to monitor 
port
computer
PC audio cable 
(optional)
RGB cable for PCRGB cable for PC
(optional)
to AUDIO IN
to PC audio 
outputto PC 
monitor
to COMPUTER
 IN
to COMPUTER OUT
When outputting to both a PC monitor and the projector.
For Macintosh
to video portcomputer
MAC adapter for
RGB cable (Optional) Monitor Conversion
adapter (optional)
RGB cable for PCMonitor cable
(optional)
to AUDIO IN
to PC audio 
output
to COMPUTER IN
to COMPUTER OUT
123456
ON DIP
PC audio 
cable (optional)
When outputting to both a PC monitor and the projector.
to PC
monitor
Projector + Personal computer
Important:
¥ Connectors or analog RGB output adapters may be necessary depending on the PC connected to this projector.
Please contact your dealer.
¥ The audio input for this projector is a stereo pin jack.  (Speaker output is mono.)  Please check the available
cable for the audio input terminal of the PC.  Some personal computer may not have the audio output terminal.
¥ Select AUDIO MODE 1 to hear and to sound for the COMPUTER. (Refer to page 16).
¥ When connecting audio output of a personal computer which audio output is mono, connect to the audio input
L terminal.
For using Macintosh
¥ A monitor output adapter is necessary for a Macintosh if it has no video port. Please contact your dealer.
¥ A MAC adapter for RGB cable may be necessary depending on the personal computer connected to this projec-
tor.  Please contact your dealer. 
						

							EN Ð 12
Adjustment foot
screen
Preparing the projector for operation
Getting ready for projection
1. Connect the power cord provided to the projector.
2. Connect the power cord to the wall power outlet.
3. Remove the lens cap.
Warning:
¥ Do not look directly into the lens when projector is
ÒONÓ.
¥ The lens cap is for protecting the lens.  If you leave
the power on with the cap on, the cap may be warped.
Please remove the lens cap when you turn the power
on.
¥ This projector is equipped with the power cords for
both U.S. and Europe.  Use the appropriate power
cord for your country.
¥ A three-pin grounding type power plug is used with
the projector. Do not remove the grounding pin on
the power plug. If you are unable to insert the plug
into the outlet, contact your electrician to replace
your A/C outlet.
¥ The supplied power cord for U.S. is used for 120V
only. Never connect to any outlet or power supply
having a different voltage or frequency. If you
connect to the power supply having a different
voltage, please use the appropriate power cord.
¥ Use 100-240V AC 50/60Hz correct voltage other-
wise it may lead to fire or electric shock.
¥ Do not place any objects on the power cord, and keep
the projector away from heat sources to avoid break-
ing the power cord. A broken power cord can cause
fire or electric shock.
¥ Do not revise or alter the power cord otherwise it
may cause fire or electric shock.
Contact your dealer if the cord is broken.
Caution:
¥ Plug in firmly and unplug by holding the plug, not
by pulling the cable out.
¥ Do not plug in or out with wet hands.  It may cause
an electric shock.
Adjusting the angle of projection
For the best result, project onto a flat screen with a 90
degree angle to the floor. If necessary, tilt the projector
by adjusting two foot adjustments on the bottom of the
projector.
1. Lift the projector to the appropriate angle.
2. Press the Front height adjuster button, this will al-
low the adjustment foot (up and down) to slide out
to the position.
3. Release the Front height adjuster button to lock the
feet in that position.
After using the projector
4. Return the adjustment foot (up and down) into the
projector by pressing the Front height adjuster but-
ton.
When the left and right angles are different
Adjust the angles with adjustment feet (right and left),
which are on the bottom of the projector.
Important:
¥ Screen on a flat wall with a 90û angle to the floor.
¥ Align projector to produce a full screen display as
illustrated on page 9.
¥ The distance from the projector to the screen must
be compatible with screen size chart on page 9.
Note the distance from the screen chart.
Adjustment foot
(up and down)
Front height
adjuster button
Adjustment foot
(right and left) 
						

							«EN Ð 13
ENGLISH
To operate projector power ON
¥ When the lamp indicator is blinking red, the the
lamp should be replaced.  Replace the lamp. See
pages 23 and 26.
¥ The picture might not be of optimum performance
in extreme hot or cold conditions. (The projector is
not malfunctioning.)
4.  Select the desired external input source by using
the COMPUTER or VIDEO button.
¥ The COMPUTER or VIDEO buttons do not work
when MENU is displayed.
¥ The projector automatically selects the appropriate
signal format. The selected signal format is dis-
played on the screen.
¥ When selecting the COMPUTER input, the image
may  flicker.  Press the $ or % button to adjust the
image.
¥ When input signal is jittering, please adjust by $
or % button also connecting with DVD player or
MUSE decoder etc.
¥ When supplying unstable signal like Still or
Reverse play with VCR, ÒNO SIGNALÓ may
appear on the screen. In this case, you may avoid
this issue by selecting the right color format like
NTSC, PAL in OPTION menu.
5.   Adjust the image size with the zoom ring by turn-
ing it.
6. Adjust the focus with the focus ring by turning it. 1. Turn on the equipment connected to the projector.
2. Put the projector into standby mode by pressing the
main power switch. The POWER indicator lights up
red.
¥ The POWER indicator blinks red for 2, 3
seconds after the power switch ON. In this
time, the buttons will not work.
3. Turn the projector on by pressing the POWER button.
The light source lamp starts warming up, eventu-
ally turning completely on.  In case the light source
lamp does not come on, wait for one minute before
switching power on again.
¥ If the main power switch to the unit is turned
off within two minutes of turning off the light
source lamp, power will not be applied to the
lamp for one minute when the next time the
main unit power switch is turned on. When
this happens, the indicator lamp will blink for
one minute.
ConditionIndicator
LAMPPOWER
Stand-by
-Red
When light source lamp is onGreen
Green
Light source lamp held off temporarilyRed-
Important:
¥ A darkened image may be seen right after pressing
the POWER button due to warming up of this pro-
jector. While warming up, no other commands can
be accepted.
OIS-VIDEO
VIDEO
AUDIO L
  (MONO)
AUDIO R
AC INMAIN
VIDEO IN COMPUTER IN COMPUTER OUTRS-232C USB
2  •  9
AUTO POSITION
buttonMUTE button
STILL button
3 • 7 • 8
4
4
POWER
LAMP
VOLUME
TEMPVIDEO
ENTERMUTEMENU SOURCE
COMPUTERAUTO POSITION
POWER MUTE
COMPUTERVIDEO
MOUSE LASER
MENU ENTERR-CLICK
AUTO POSITIONSTILL
P in P EXPAND
VOLUME –+
3 • 7 • 8 4MUTE button
AUTO POSITION button
wide
zoom ringtele
far near
focus ring 
						

							EN Ð 14
Turning off the projector
7. Press the POWER button.
The message ÒPOWER OFF? YES : PRESS AGAINÓ
appears on the screen.
¥ To exit from this mode,  press any button except
POWER, LASER, mouse pointer, R/L-click,
STILL and VOLUME + and - buttons.
8. Press the POWER button again.
The light source lamp will be turned off.
Pressing the POWER button second time  will shut
off the light source lamp, but the exhaust fan con-
tinues to operate for 120 seconds to cool down the
light source lamp and LCD panels. In this time, the
lamp indicator will be turned off.
9. Turn off the main power switch. When turning off
the main switch, the POWER indicator turns off.
¥ In cases where the main power switch is acciden-
tally turned off when either the intake/exhaust
fan or the power source lamp is in operation, allow
the unit to cool down for 10 minutes with the
power turned off. Repeat step 3 when turning on
the power source lamp. If the lamp does not turn
on immediately, repeat this step two or three
times. Replace the lamp if it should still fail to
turn on.
AUTO POSITION button
When the source is selected to COMPUTER and the
image is not in the right place, set the screen to the
brightest display possible, then press the AUTO
POSITION button on the remote control. If the image
is still not in the right place.
¥ Set screen to the brightest display as possible
(e.g., full-screen display of the ÒTrashÓ window)
before deploying the automatic adjustment func-
tion.
¥ If the screen saver is running, turn off the screen
saver before using the automatic adjustment
button.
The sound from the speaker
The sound from the speaker is mono.
¥ When inputting mono sound, connect to AUDIO L
terminal.
¥ The output sound is selected by changing the
setting of AUDIO MODE in the FEATURE menu.
See page 16 for details.
The volume from the speaker
Press the volume + or Ð button to change the volume
from the speaker.
The volume control bar will appear on the screen.
30
¥ The volume control bar will disappear about 4
seconds after releasing the volume buttons.
¥ The volume buttons do not work when MENU
selection bar or MENU is displayed.
¥ The volume from the audio output terminals are not
changed.
AV mute
Image and audio are temporarily erased with press-
ing the MUTE button. To restore the image and
audio to the normal mode, press the MUTE button
again.
¥ To prevent the damage of the LCD, the image and
audio will be restored automatically to the normal
mode, 10 minutes after setting the AV mute mode.
¥ The audios from the audio output terminals and PC
audio output terminal are not muted.
Caution:
¥ When you have finished using this equipment, wait
120 seconds for the exhaust fans to stop. Then turn
off the main switch and unplug the power cable from
the wall outlet, for safety purposes.
¥ After the lamp is turned off,  the lamp cannot be
switched on again for 60 seconds as a precaution-
ary measure. It will take another 60 seconds before
the lamp indicator goes off. If you wish to turn on
the projector again, wait until the indicator is off
then press the POWER button.
¥ The exhaust fan rotates faster when the tempera-
ture around the projector rises.
¥ When the temperature around the projector becomes
too high, the sign  ÒTEMP!!Ó blinks red on the screen.
If the temperature stays too high, the lamp will be
shut off automatically .
The projector automatically shuts off when the
lamp is used up in about 2000 hours. You must
replace the lamp.
To operate projector power ON (Continue) 
						

							EN Ð 15
ENGLISH
Basic operation
Several settings can be adjusted using Menu.
EXAMPLE: Auto power off time setting
1.  Press the MENU button.
2.  Press the $ or % button to select the INSTALLA-
TION menu.
3.  Press the ENTER button (or } button).4.  Press the { or } button to select AUTO POWER
OFF.
5.  Press the $ or % button to adjust auto power off
time.
6.  Exit the menu system by pressing the MENU but-
ton several times.
¥ If the menu operation is not working, press the
RESET button on the terminal board using the suit-
able implement
¥ If the COMPUTER or VIDEO button is pressed, the
MENU selection bar or MENU will disappear.
¥ The settings with 2 mark, you should press the
ENTER button after selecting.
Menu operation
Opt
IMAGE
XGA60
INSTALLATION
OptXGA60
IMAGE REVERSE
INSTALLATION
OFF
AUTO POWER ON OFF
AUTO POWER OFF OFF
OptXGA60
IMAGE REVERSEOFF
AUTO POWER ON OFF
AUTO POWER OFFOFF
IMAGE REVERSEOFF
AUTO POWER ON OFF
AUTO POWER OFF30 min
IMAGE CONTRAST± 30
BRIGHTNESS± 30
1COLOR MATRIX
SHARPNESS± 10
TINT± 10
COLOR± 10RED± 10
YELLOW± 10
BLUE± 10
GREEN± 10
CYAN± 10
MAGENTA
(Displays only when the source is selected to VIDEO)
(Displays only when the source is selected to VIDEO)
(AUTO : When the source is selected to COMPUTER)± 10
CONTRAST R± 30
CONTRAST B± 30
BRIGHTNESS R± 30
BRIGHTNESS B± 30
EXPAND MODE 1 - 2
1=Upper left, 2=Lower right
INSTALLATION IMAGE REVERSE OFF, MIRROR, INVERT, MIRROR INVERT
AUTO POWER ON ON, OFF
AUTO POWER OFF
1 - 3
ON, OFF
FEATURES MENU POSITION
OFF, 5, 10, 15, 30, 60 min
VIDEO SIGNAL
AUDIO MODE
ANAMORPHICAUTO, NTSC, PAL, SECAM, 4.43NTSC, PAL-M, PAL-N, PAL-60
LANGUAGE
SIGNALMEMORY CALL AUTO, USER1, USER2
HORIZ.POSITION 0 - 999
VERT.POSITION 0 - 999
FINE SYNC. 0 - 39
TRACKING
USER0 - 9999CLAMP POSITION 0 - +63
CLAMP WIDTH 0 - +63
HORIZ. PIXELS 0 - 9999
VERT LINES 0 - 9999
PLL
AUTO, 0 - 7
SHUTTER (L)
0 - 299
SHUTTER (U)
0 - 299
VERT. SYNC
AUTO, ON, OFF
2 
3
USER
USER 
OFF
STANDARD
HIGH
LOW
COLOR TEMP.
USER 
MEMORIZE
*
*
*
HOLD AUTO
USER1, USER2
DELETEUSER1, USER2
DEFAULT
ONBEGIN -1 - -99
END 1 - 99
OFF
COMPUTER INPUT RGB, YCBCR / YPBPR
*
*
*
* * : Setting range is different 
     according to the type of 
     the signal.
, English, Español, Deutsch, Français, Italiano, 
						

							EN Ð 16
IMAGE REVERSE
INSTALLATION
OFF
AUTO POWER ON OFFAUTO POWER 
OFFOFF
OptXGA60
MENU POSITION
FEATURE
AUDIO MODE 2
ANAMORPHIC OFF
LANGUAGE English
VIDEO SIGNAL AUTO
AË ?
OptXGA60
EXPAND MODE 1.AA
1.
1 IMAGE
CONTRAST ........ Adjusts the picture contrast. The contrast becomes higher
as the number increases.
BRIGHTNESS .... Adjusts image brightness. The image becomes brighter as
the number increases.
COLOR MATRIX. ......Adjusts color balance in each color of the image. See page
18.
COLOR TEMP... . Adjusts color temperature. See page 18.
SHARPNESS ......Adjusts the picture sharpness. The sharpness becomes
sharper as the number increases.
TINT .................... Adjusts the color balance of the image.  The color balance
of the image shifts green as the number increases and
shifts to purple as the number decreases (displays only when the source is selected to
VIDEO).
¥ When the TV50 (PAL, SECAM) signal is inputted, you cannot adjust the TINT.
COLOR ................ Adjusts the color intensity of the image (displays only when the source is selected to VIDEO).
2 INSTALLATION
IMAGE REVERSEUse to reverse or invert the projected image.  MIRROR is
used for rear projection.  MIRROR INVERT is effective
when the projector is ceiling-mounted.
AUTO POWER ON.....To select whether to boot up automatically when the power is
turned on external to the projector. In this case, the main
power switch of the projector has to be ON.  Set this when the
projector is hanging on the ceiling.
¥ The projector is in stand-by mode when the lamp is not
on. In this case, use the remote control to turn on the lamp.
AUTO POWER OFF ..Use to select the length of time before projector switches to stand-by when there is no input
signal selected source. Select 0 min. to cancel this function.
3 FEATURES
MENU POSITION .Use to select the position where the menu is displayed, 
(upper left) or  (lower right).
EXPAND MODE Selects the mode of enlarging screen. See page 21.
AUDIO MODE .......Select 1 (COMPUTER mode) to output the sound which is
inputted to audio input terminal only  when the source is
selected to COMPUTER. Select 2 (VIDEO mode) to output
the sound which is inputted to audio input terminal only
when the source is selected to VIDEO. Select 3
(PARMANENT mode) to output the sound which is
inputted to audio input terminal all time.
SPLASH SCREEN .Use to display the splash screen on the screen when the power is turned ON.
VIDEO SIGNAL . When AUTO is set, the appropriate video format is automatically selected according to the
input signal. If the image does not appear correctly, select the desired video format
manually.  Adjust the projector to the appropriate format when the projector either is not
projecting normally in auto mode or is projecting PAL-M/PAL-N signals.
ANAMORPHIC ... Set to ON when displaying DVD discs which are recorded as squeezed images (in right and
left direction).
LANGUAGE ....... Use to select the language for the projector display such as menu. (
 / English / Espa–ol

)
Opt
CONTRAST
IMAGE
0
BRIGHTNESS 0
COLOR TEMP. STANDARD
TINT 0
COLOR 0
SHARPNESS 0
XGA60
COLOR MATRIXUSER
Menu operation (continued) 
						

							EN Ð 17
ENGLISH
4 SIGNAL
MEMORY CALL ........Use to select AUTO, USER 1 or USER 2. See below.
HORIZ. POSITION ....Use to adjust the horizontal position of the image.
VERT. POSITION .....Use to adjust the vertical position of the image.
FINE SYNC. ....... Use to synchronize the projector with PC input signals so
that the image is not blurred.
TRACKING ......... Use to avoid image noise such as wide stripes.
COMPUTER INPUT ....The unit adjusts itself automatically when connected to
either DVD players with a component video output
terminal (Y, C
B, CR or Y, PB, PR) or equipment with HDTV
signal output capabilities. In cases where the unit is
connected to equipment that include an RGB output
terminal and which output HDTV signals, adjust the unit
to RGB mode.
HOLD .................. Adjusts the image when curving near the top.
5 SIGNAL  - USER (Normally, there is no need for adjustments.)
CLAMP POSITION/
CLAMP WIDTH .........
If you use something similar, the brighter colors of the
projected image may become blurred. In this case, adjust
CLAMP POSITION or CLAMP WIDTH.
HORIZ.PIXELS ..Use to adjust the width of the image.  The image size
grows wider as the number increases.  (Adjust to the
horizontal pixels of the input signal for normal setting.)
VERT.LINES ......Use to adjust the height of the image.  The image size
grows higher as the number increases.  (Adjust to the
vertical lines of the input signal for normal setting.)
PLL ...................... Use to adjust the image when skewed on top.  Select AUTO for normal setting.
VERT.SYNC. ......Use to adjust the image when its motion does not run smoothly.  Select AUTO for normal
setting.
SHUTTER(U) ..... Use to adjust the image when the noise etc. appears on top part of image.
SHUTTER(L) ...... Use to adjust the image when the noise etc. appears on bottom part of image.
User memory for signal setting
This projector can memorize the maximum of 2 signal menu settings.
Memorizing the setting
1.  Select MEMORIZE in the SIGNAL menu, and press the ENTER button.
2.  Press the $ or % button to select the memory which you wish to record (USER 1 or USER 2).
3.  Press the ENTER button.
Initialite the setting which has been changed (Default)
Select RESET in the SIGNAL menu, and press the ENTER button.
¥ When initializing, selection buttons will not work for about 2 - 18 seconds.
Select the user setting
Select MEMORY CALL in SIGNAL menu, and press the $ or % button to select the memory (USER 1 or USER 2).
Reset the recorded setting
1.  Select DELETE in the SIGNAL menu, and press the ENTER button.
2.  Press the $ or % button to select the memory which you wish to reset (USER 1 or USER 2).
3.  Press the ENTER button.
The recorded setting will be reset.
CLAMP POSITION
SIGNAL – USER
0
CLAMP WIDTH + 5
HORIZ. PIXELS 800
PLL AUTO
SHUTTER(L) 0
VERT. LINES 600
VERT. SYNC. AUTO
SHUTTER(U) 0
?
MEMORY CALL
SIGNAL
AUTO
HORIZ. POSITION 208
VERT. POSITION 22
TRACKING 1056
COMPUTER INPUT RGB
FINE SYNC. 24
HOLD AUTO
USERMEMORIZEDELETE DEFAULT
R G BR G B
A
U
OptXGA60 
						

							EN Ð 18
Adjusting the image
You can adjust the picture by using the IMAGE menu.
To control the level of white-to-black in the image :
Adjust CONTRAST in IMAGE menu.  Press the %
button to increase the contrast and the $ button to
reduce it.
To control the light level of the image :
Adjust BRIGHTNESS in IMAGE menu.  Press the %
button to lighten the image and the $ button to
darken the image.
To adjust the detail and clarity of the image :
Adjust SHARPNESS in IMAGE menu.  Press the %
button to make the picture seem sharper and the $
button to make it softer.
To determine the intensity of the color :
Adjust COLOR in IMAGE menu.  Press the %
button to increase the amount of color in the image
and the $ button to decrease it.
To adjust the red-green color balance of the image :
Adjust TINT in IMAGE menu.  Press the % button
to increase the amount of red in the image and the $
button to increase the amount of green in the image.
Color matrix
This feature adjusts the color balance in each color of
RGB (Red, Green, Blue), and their neutral colors
(yellow, cyan, magenta) by using Color correction
adjustment. Use Color correct adjustment when
enphasizing a specific color, or when only a certain
color balance is not correctly adjusted.
1.  Select COLOR MATRIX in IMAGE menu.
2.  Press the ENTER button.
When using the setting which has been already
prepared
3.  Press the $ or % button to select 1, 2, or 3.
¥ Select 1, 2 or 3 in the color matrix adjustment at
your option. Selecting VIDEO input automati-
cally selects 1 and selecting COMPUTER input
automatically selects 3. 2 is recommended for
images with high color temperature.
Picture adjustment
CONTRAST R
COLOR TEMP.-USER
0
CONTRAST B 0
BRIGHTNESS R 0
BRIGHTNESS B 0
Opt
CONTRAST
IMAGE
0
BRIGHTNESS 0
COLOR TEMP. STANDARD
TINT 0
COLOR 0
SHARPNESS 0
XGA60
COLOR MATRIXUSER
About color temperature
There are different kinds of white color. Color temperature is
a way to show the differences. The white, which temperature
is low, becomes raddish white. When the color temperature is
higher, the white becomes more bluish. This projector sets
this color temperature by changing the numbers of contrast
blue and red.
To set the color temperature high:
Set the contrast B (Blue) number high, and the contrast R
(Red) number low.
To set the color temperature low:
Set the contrast B (Blue) number low, and the contrast R
(Red) number high.
¥ Select OFF when not using Color matrix adjust-
ment.
When using the user setting
4.  Press the $ or % button to select USER }.
5.  Press the { or } button to select the desired color.
6.  Press the $ or % button to adjust the color balance
of the color.
7. Repeat steps 5 and 6 for more adjusting.
8. Exit the menu system by pressing the MENU but-
ton several times.
Color temperature
1.  Select COLOR TEMP in IMAGE menu.
2.  Press the $ or % button to select USER 2.
3.  Press the ENTER button.
4.  Press the { or } button to select the desired item.
5.  Press the $ or % button to adjust the item.
6. Repeat steps 4 and 5 for more adjusting.
7. Exit the menu system by pressing the MENU but-
ton several times.
COLOR MATRIX
RED 0
BLUE 0
CYAN 0
MAGENTA 0
YELLOW 0
GREEN0
123USEROFF 
						

							EN Ð 19
ENGLISH
Adjustment from personal computer
Although this projector sets proper signal systems
automatically for the image signal from personal
computers, it cannot be applied to some of personal
computers.  In this case, press the AUTO POSITION
button.  If the images are still not projected correctly,
use the MENU display to adjust the projected im-
ages.
Image moved to right or left :
Adjust HORIZ. POSITION in SIGNAL menu.  Press
the % button to move the image to left.  Press the $
button to move the image to right.
Image moved to up or down :
Adjust VERT. POSITION in SIGNAL menu.  Press
the % button to move the image to upward.  Press
the $ button to move the image to down.
Image flickers / Image is out of focus :
Adjust FINE SYNC. in SIGNAL menu.
Wide stripes appear :
Adjust CLAMP POSITION or CLAMP WIDTH of
each menu in SIGNAL - USER menu.
Noise etc. appears on right or left side of image :
Adjust HORIZ. PIXELS  of the menu in SIGNAL -
USER menu.
Noise etc. appears on top or bottom part of image :
Adjust SHUTTER (U), SHUTTER (L) or VERT.
LINES of the menu in SIGNAL - USER menu.
MEMORY CALL
SIGNAL
AUTO
HORIZ. POSITION 208
VERT. POSITION 22
TRACKING 1056
COMPUTER INPUT RGB
FINE SYNC. 24
HOLD AUTO
USERMEMORIZEDELETE DEFAULT
R G BR G B
A
U
OptXGA60
CLAMP POSITION
SIGNAL – USER
0
CLAMP WIDTH + 5
HORIZ. PIXELS 800
PLL AUTO
SHUTTER(L) 0
VERT. LINES 600
VERT. SYNC. AUTO
SHUTTER(U) 0
?
Top part of image curves :
Change the setting of HOLD in SIGNAL menu or
PLL in SIGNAL - USER menu.
HOLD ... Select ON, and adjust BEGIN or
               END for image which top part is the
               least curved.
PLL ....... Select FAST, NORMAL, or SLOW for an
               image in which top part is the least
               curved.  Select AUTO for normal setting.
Image does not move naturally :
Adjust VERT. SYNC. of the menu in SIGNAL -
USER menu.  Select AUTO for normal setting.
curved.  Select AUTO for normal setting.
¥ Do not change each menu setting in USER
menu for normal setting.
Simple adjustment method
1. Select HORIZ. POSITION in SIGNAL menu.
2. Press the$ or % button to adjust the horizontal
start position (the left end).
3. Select TRACKING in SIGNAL menu.
4. Press the$ or % button to adjust the horizontal
end position (the right end).
5. Repeat steps 1 to 4 for fine adjustment.
6. Select VERT. POSITION in SIGNAL menu.
7. Press the$ or % button to adjust the vertical
start position (the top end). 
						

							EN Ð 20
Specification of RGB signals in each computer mode of the projector
¥ When the EXPAND MODE of FEATURE menu is
set to real screen display, by pressing the EXPAND
button on the remote control, it will switch to the
screen displaying the picture as its original size (real
screen display).  In the real screen display, pictures
will be black-framed when picture resolution is lower
than 800 x 600.
Important:
¥ Some computers may not be compatible with the
projector.
¥ The projectors maximum resolution is 800 x 600 pix-
els.  It may not display correctly for the pictures of
higher resolutions than 800 x 600.
¥ The picture with a SYNC on G (Green) signal may
jitter.
¥ The picture with a SYNC on G (Green) signal may
be tinged with green.¥ If the resolution and frequency of your computer
are not shown on the table, change the resolution
of your computer. You may find the compatible reso-
lution and frequency.
¥ Set the COMPUTER INPUT in SIGNAL menu to RGB,
when inputting the HDTV signal as RGB signal.
¥ Set the SIGNAL menu and USER menu as shown
below, when 525p signal is inputted.
HORIZ. POSITION .......................143
VERT. POSITION .........................54
TRACKING ............................. 800
COMPUTER INPUT ............... YC
BCR/YPBPR
CLAMP POSITION .......................+9
CLAMP WIDTH ............................+3
CLAMP WIDTH ............................+3
HORIZ.PIXELS .................620
VERT.LINES ......................444
VERT.SYNC. ......................ON
Picture adjustment (continued)
Signal mode resolution horizontal Vertical Normal mode Real mode
 (H x V) frequency (kHz) frequency (Hz) (H x V)  (H x V)
TV60 Ð 15.73 59.94 800 x 600 Ð
TV50 Ð 15.63 50.00 800 x 600 Ð
1080i Ð 33.75 60.00 800 x 450 Ð
720p Ð 45.00 60.00 800 x 450 Ð
PC98 640 x 400 24.82 56.42 800 x 500 640 x 400
CGA70 640 x 400 31.47 70.09 800 x 500 640 x 400
CGA84 640 x 400 37.86 84.14 800 x 500 640 x 400
CGA85 640 x 400 37.86 85.08 800 x 500 640 x 400
VGA60 640 x 480 31.47 59.94 800 x 600 640 x 480
VGA72 640 x 480 37.86 72.81 800 x 600 640 x 480
VGA75 640 x 480 37.50 75.00 800 x 600 640 x 480
VGA85 640 x 480 43.27 85.01 800 x 600 640 x 480
SVGA56 800 x 600 35.16 56.25 800 x 600 800 x 600
SVGA60 800 x 600 37.88 60.32 800 x 600 800 x 600
SVGA72 800 x 600 48.08 72.19 800 x 600 800 x 600
SVGA75 800 x 600 46.88 75.00 800 x 600 800 x 600
SVGA85 800 x 600 53.67 85.06 800 x 600 800 x 600
XGA43i 1024 x 768 35.52 86.96 800 x 600 800 x 600
XGA60 1024 x 768 48.36 60.00 800 x 600 800 x 600
XGA70 1024 x 768 56.48 70.07 800 x 600 800 x 600
XGA75 1024 x 768 60.02 75.03 800 x 600 800 x 600
XGA85 1024 x 768 68.68 85.00 800 x 600 800 x 600
MAC13 640 x 480 35.00 66.67 800 x 600 640 x 480
MAC16 832 x 624 49.72 74.55 800 x 600 800 x 600
MAC19 1024 x 768 60.24 75.02 800 x 600 800 x 600
MAC21 1152 x 870 68.59 74.96 800 x 600 800 x 600
HP75 1024 x 768 62.94 74.92 800 x 600 800 x 600