Mitsubishi Mh2850u Projector User Manual
Have a look at the manual Mitsubishi Mh2850u Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 561 Mitsubishi manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
EN-41 POWER O f f Steady r ed Blinking red/green S TA TUS O f f O f f Blinking orange Blinking g r een Steady r ed O f f Steady or Blinking Solution • Connect the power co r d to the p r ojecto r . • Plug the power co r d into a wall outlet. • If any objects a r e blocking the air inlet or outlet grille, r emove them and carry out the following. 1. Unplug the power co r d f r om the wall outlet. 2. Make su r e that the p r ojector has cooled o f f. 3. Plug the power co r d into the wall outlet. 4. P r ess the POWER button. • If any objects a r e blocking the air inlet or outlet grille, r emove them. • Don't expose the air outlet grilles to hot air emitted f • Check wheather the filter is clogged with dirt and dust. Clean the filter, if clogged. (See page 40.)r om a heating appliance. • After the S TA TUS indicator stops blinking, p r ess the POWER button. • If you unplug the power co r d while the fan is r otating, the lamp may not tu r n on about 1 minute when you plug the power co r d next time. • The lamp can't tu r n on again for 1 minute after it goes out. • P r ess the POWER button several times. • Replace the lamp. (The lamp is at the end of its life.) • Attach the lamp cover on the bottom. • Unplug the power co r d f r om the wall outlet and contact your deale r . Troubleshooting Before asking for repair of the projector, check the following. If the symptom persists, stop using the projector, be sure to unplug the power plug, and then contact your dealer. No image appears on the screen. Problem Power can not be turned on. No image appears on the screen. Power turns off. Solution • Check whether the indicators are on or off and how they are lightning. • Cancel the AV mute by pressing the MUTE button. • Check that the lens cap is removed. • It may take about 1 minute for the lamp to light up. • The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again. • If the projector was turned off before the lamp was cooled down suffi ciently last time, the fan may start rotating and the POWER button may not work after the power cord is plugged. After the fan stops rotating, press the POWER button to turn back on the POWER indicator. • Set SCART INPUT in the FEATURE menu to OFF. (See page 25.) • Check that the intake vent is clean. • Check that the lamp cover is closed. (See page 39.) • Check that the cables connected to the external devices are not broken. • When an extension cable is being used, replace it with the supplied cable for check. When images are displayed correctly, add an RGB signal amplifier to the extension cable. • This problem may occur when the intake vent and/or exhaust vents are blocked. (In such a case, the STATUS indicator brinks orange.) Remove the objects blocking the intake vent and/or exhaust vents and then carry out the following procedure. 1. Wait for the intake fan and/or exhaust fan to stop. (Wait until the STATUS indicator goes out.) 2. Unplug the power cord from the wall outlet. 3. Wait about 10 minutes. 4. Plug the power cord into the wall outlet. 5. Press the POWER button. • When the STATUS indicator is steady red, it is indicating that the lamp should be replaced. Replace the lamp in this case. • Check that AUTO POWER OFF has been set to OFF. • If the lamp has deteriorated, it may go out after a while it illuminates.
EN-42 Images are not displayed correctly. Problem Projected images are shaking. Projected images are displaced. Projected images are distorted. Projected images are dark. Projected images are blurred. Afterimages persist on the screen. Red, blue, and green dots appear in projected images. Black dots appear in projected images. Fine streaks are seen on projected images. Projected images become wavy. Hue is not appropriate. Tint in projected images is incorrect. Different color tint.Solution • Check that the cable connected to the external device isn’t intermittent. • Connect the cable’s plug with the external device’s connector fi rmly. • Project an image containing many characters such as a help menu and press the AUTO POSITION button. • Some computers output out-of-spec signals on rare occasion. Adjust the SIGNAL menu. (See pages 30 and 31.) • Adjust the projector and the screen so that they are perpendicular to each other. (See page 10.) • Adjust BRIGHTNESS and CONTRAST in the IMAGE menu. (See page 28.) • Replace the lamp. (See page 38.) • Adjust the focus. (See pages 15 and 19.) • Clean the lens. • Press the or button on the remote control to eliminate fl icker. • Adjust TRACKING and FINE SYNC. in the SIGNAL menu. (See page 31.) • Adjust BRIGHTNESS and CONTRAST in the IMAGE menu. (See page 28.) • Adjust the projector and the screen so that they are perpendicular to each other. (See page 10.) • This phenomenon is improved by keeping projecting an evenly dark image. (Such “image burn-in” phenomenon where afterimages persist on the screen may occur if a stationary image is kept displayed on the screen for a long time.) • This phenomenon is unique to LCD projector and isn’t a product malfunction. (A small number of pixels always stay on or off, which are not malfunctions. More than 99.99% of the pixels are effective.) • This is due to interference with the screen surface and is not a malfunction. Replace the screen or displace the focus a little. • Vertical or horizontal streak noise may appear on the projected image, depending on the type of the DVD player or game console you use. In such a case, you can reduce such streak noise by enabling the LPF. • Connect the plugs of the cables to external devices securely. • Keep the projector away from devices that emit interfering radio waves. • When the keystone adjustment is carried out, the image may not be displayed correctly depending on the type of input signal. This isn’t a product malfunction. In this case, readjust the keystone so that the amount of keystone correction is as small as possible. • Check that the cables connected to the external devices are not broken. • Check that COMPUTER INPUT in the SIGNAL menu is correctly set. (See page 26.) • Check that the cable connected to the external device isn’t broken. • When comparing images projected by two projectors, tints in the displayed images may be different because of variation between their optical components. This is not a malfunction. • When comparing the image projected by this projector with those displayed on the television or PC monitor, tints in the displayed images may be different because of difference in the range of color reproducibility. This is not a malfunction. No image appears on the screen. (continued) Problem The screen for entering the password appears. “NO SIGNAL” is displayed.Solution • PASSWORD FUNCTION in the FEATURE menu has been set to DISPLAY INPUT to enable the password lock. Enter the password or contact the person in charge of management of the projec- tor. (See page 33.) • Turn on the power of the connected device, or check whether there is something wrong with the connected device. • Check whether the external device output signals. (Check this especially when the external device is a notebook computer.) • Check that the cable connected to the external device isn’t defective. • Check that the projector is connected to the external device using the correct terminals. • Check that the connected device is correctly selected as the input source. • When an extension cord is being used, replace it with the supplied cable and check whether images are projected correctly. If images are projected correctly, use an RGB signal amplifi er along with the extension cord. Troubleshooting (continued)
EN-43 Others Problem The exhaust vents emit warm air. No audio is output. The menu can’t be used. “TEMPERATURE!!” is displayed. The mark appears. The remote control doesn’t function easily or at all. The buttons on the control panel (except for the POWER button) don’t function. Solution • This air comes out after cooling the inside of the projector. You may feel hot, but this is not a malfunction. • Check that the volume isn’t set to low. • The microcomputers inside the projector may be wrongly operating because of noise. Press the POWER button to turn off the lamp and unplug the power cord from the wall outlet. Wait about 10 minutes, plug the power cord in, and try again. • This indication appears when the ambient temperature rises high. When the ambient temperature stays high, the lamp goes out. Eliminate any causes of the rise in the ambient temperature. • This indication appears when the air inlet or outlet grille is blocked. When they are kept blocked, the lamp goes out. Remove the objects blocking the air inlet or outlet grille. • This mark appears when ineffective operation is carried out. This isn’t a product malfunction. • Check that the batteries are loaded in the remote control or the batteries are not weak. (See page 6.) • Check that the remote control sensor isn’t exposed to direct sunlight or fl uorescent light. (See page 9.) • Use the remote control within its operation range. (See page 9.) • Use the remote control at least 10 cm away from the projector. • PASSWORD FUNCTION in the FEATURE menu has been set to MENU ACCESS to enable the password lock. Cancel the password lock or contact the person in charge of management of the projector. (See page 33.) If the following problem occurs after the lamp is replaced, check the following fi rst. Problem The projector does not turn on. The STATUS indicator blinks.Solution • Fit the lamp cover securely. (See pages 38 and 39.) • Reset the lamp operating time. (See page 39.) • Reset the lamp operating time. (See page 39.) Kensington Lock This projector has a Kensington Security Standard connector for use with Kensington MicroSaver Security System. Refer to the information that came with the Kensington System for instructions on how to use it to secure the projector. Please contact Kensington Technology Group below. Kensington Technology Group 2855 Campus Drive San Mateo, CA 94403, U.S.A. Phone: +1- (650)572-2700 Fax: +1- (650)572-9675 Problem Only the motion areas in the images supplied from the computer aren’t displayed. Projected images are obscured. Noise appears around the image. Solution • This is caused by the computer being used. Contact the manufacturer of your computer. • Match the output resolution of your computer with the resolution of the projector. For the method to change the output resolution of the computer, contact the manufacturer of your computer. (See page 45.) • Some images and texts appear obscured during the keystone adjustment. In such cases, use the projector without applying the keystone adjustment. (See page 21.) • In some images such as DVD, noise may appear around the recorded image. In this case, decrease the setting value of OVER SCAN of the SIGNAL menu. (See page 26.) Images are not displayed correctly. (continued) Troubleshooting (continued)
EN-44 Specifi cations The specifi cations and outside appearance of the projector are subject to change without prior notice. Replacement part (option/not included in the box) Spare lamp: VLT-XL650LP Option lenses: OL-XL2550MZ, OL-XL2550LZ, OL-XL2550TZ Type Model Display Technology Projection lens Light-source lamp Image size (Projection distance) Maximum resolution Computer signal Video signal Component signal Computer/Component video input Video input Audio input Monitor output Audio output Speaker Control terminal/Others Operating temperatures Rated voltage Power consumption Dimensions Weight Others S-video input Video input Component video input Analog input Digital input (DVI) Audio inputLCD projector MH2850U 0.8-inch LCD panel: 3 pieces (for R,G,B) Pixel: 1400 x 1050 = 1470000 pixels Total 4410000 pixels Active pixel rate: 99.99% or more (each panel) F 1.7 - 1.9 f= 24 - 29 mm 261 W 40” min. to 300” max. (Projection distance 1.2 to 9.1 m) Maximum resolution: 1600 x 1200 dots/compressed Panel resolution: 1400 x 1050 dots NTSC/PAL/SECAM/4.43NTSC/PAL-M/PAL-N/PAL-60 480i, 480p, 576i, 576p, 720p, 1080i, 1080p Panel resolution: 1400 x 1050 dots [Signal type] [Terminal type] [Line] Analog RGB Mini D-SUB 15-pin 2 Digital RGB DVI-D 1 [Signal type] [Terminal type] [Line] Video input RCA 1 S-Video input S 1 [Signal type] [Terminal type] [Line] RGB Stereo mini jack (ø3.5) 2 Video RCA (L, R) 1 S-video RCA (L, R) 1 [Signal type] [Terminal type] [Line] Analog RGB Mini D-SUB 15-pin 1 [Signal type] [Terminal type] [Line] RGB/Video/S-video Stereo mini jack (ø3.5) 1 3 W Mono Round type ø4.5 cm x 1 RS-232C (D-SUB 9-pin), USB terminal, LAN terminal (RJ-45) +41°F (+5°C) to +95°F (+35°C) AC100 - 240 V, 50/60 Hz 3.9 A 333 mm (W) x 125 mm (H) x 272 mm (D) * Not including protrusion. 4.9 kg Luminance signal: Vp-p=1.0 V 75 Ω (negative sync) Chrominance signals: Vp-p=0.286 V 75 Ω (burst signal) Vp-p=1.0 V 75 Ω (negative sync) YC BCR: Vp-p=1.0 V 75 Ω (Y) (negative sync) Vp-p=0.7 V 75 Ω (C B, CR) RGB: Vp-p=0.7 V 75 Ω YC BCR: Vp-p=1.0 V (Y) (negative sync) Vp-p=0.7 V (CB, CR) HD/CS: TTL-level (negative or positive polarity) VD: TTL-level (negative or positive polarity) DVI-D interface (TMDS single link) with HDCP 350 mVrms, 10 kΩ or more
EN-45
TV60, 480i (525i) - 15.73 59.94 1400 x 1050 - *1
TV50, 576i (625i) - 15.63 50.00 1400 x 1050 - *1
1080i 60 (1125i 60) - 33.75 60.00 1400 x 788 - *1, *2
1080i 50 (1125i 50) - 28.13 50.00 1400 x 788 - *1, *2
480p (525p) - 31.47 59.94 1400 x 1050 - *1, *2
576p (625p) - 31.25 50.00 1400 x 1050 - *1, *2
720p 60 (750p 60) - 45.00 60.00 1400 x 788 - *1, *2
720p 50 (750p 50) - 37.50 50.00 1400 x 788 - *1, *2
1080p 60 (1125p 60) - 67.50 60.00 1400 x 788 - *1, *2
1080p 50 (1125p 50) - 56.25 50.00 1400 x 788 - *1, *2
CGA70 640 x 400 31.47 70.09 1400 x 900 640 x 400
CGA84 640 x 400 37.86 84.13 1400 x 900 640 x 400
CGA85 640 x 400 37.86 85.08 1400 x 900 640 x 400
VGA60 640 x 480 31.47 59.94 1400 x 1050 640 x 480 *2
VGA72 640 x 480 37.86 72.81 1400 x 1050 640 x 480
VGA75 640 x 480 37.50 75.00 1400 x 1050 640 x 480
VGA85 640 x 480 43.27 85.01 1400 x 1050 640 x 480
SVGA56 800 x 600 35.16 56.25 1400 x 1050 800 x 600
SVGA60 800 x 600 37.88 60.32 1400 x 1050 800 x 600 *2
SVGA72 800 x 600 48.08 72.19 1400 x 1050 800 x 600
SVGA75 800 x 600 46.88 75.00 1400 x 1050 800 x 600
SVGA85 800 x 600 53.67 85.06 1400 x 1050 800 x 600
SVGA95 800 x 600 59.97 94.89 1400 x 1050 800 x 600
XGA60 1024 x 768 48.36 60.00 1400 x 1050 1024 x 768 *2
XGA70 1024 x 768 56.48 70.07 1400 x 1050 1024 x 768
XGA75 1024 x 768 60.02 75.03 1400 x 1050 1024 x 768
XGA85 1024 x 768 68.68 85.00 1400 x 1050 1024 x 768
SXGA70a 1152 x 864 63.85 70.01 1400 x 1050 1152 x 864
SXGA75a 1152 x 864 67.50 75.00 1400 x 1050 1152 x 864
SXGA85a 1152 x 864 77.49 85.06 1400 x 1050 1152 x 864
WXGA60 1280 x 768 47.78 59.87 1400 x 840 1280 x 768 *2
WXGA60a 1280 x 800 49.70 59.81 1400 x 875 1280 x 768 *2
WXGA60b 1360 x 768 47.71 60.02 1400 x 790 1280 x 768
WXGA60c 1366 x 768 47.50 59.75 1400 x 788 1280 x 768
WXGA+60 1440 x 900 55.94 59.89 1400 x 875 1400 x 900 *3
SXGA60b 1280 x 960 60.00 60.00 1400 x 1050 1280 x 960
SXGA75b 1280 x 960 75.00 75.00 1400 x 1050 1280 x 960
SXGA85b 1280 x 960 85.94 85.00 1400 x 1050 1280 x 960
SXGA60 1280 x 1024 63.98 60.02 1312 x 1050 1280 x 1024 *2
SXGA75 1280 x 1024 79.98 75.02 1312 x 1050 1280 x 1024
SXGA85 1280 x 1024 91.15 85.02 1312 x 1050 1280 x 1024
MAC13 640 x 480 35.00 66.67 1400 x 1050 640 x 480
MAC16 832 x 624 49.72 74.55 1400 x 1050 832 x 624
MAC19 1024 x 768 60.24 75.02 1400 x 1050 1024 x 768
HP75 1024 x 768 62.94 74.92 1400 x 1050 1024 x 768
HP72 1280 x 1024 78.13 72.00 1312 x 1050 1280 x 1024
SUN66a 1152 x 900 61.85 66.00 1344 x 1050 1152 x 900
SUN76a 1152 x 900 71.81 76.64 1344 x 1050 1152 x 900
SUN66 1280 x 1024 71.68 66.68 1312 x 1050 1280 x 1024
SUN76 1280 x 1024 81.13 76.11 1312 x 1050 1280 x 1024
SGI72 1280 x 1024 76.92 72.30 1312 x 1050 1280 x 1024
SGI76 1280 x 1024 82.01 76.00 1312 x 1050 1280 x 1024
SXGA+60 1400 x 1050 63.98 60.02 1400 x 1050 1400 x 1050
1400 x 1050 65.32 59.98 1400 x 1050 1400 x 1050 *2
SXGA+75 1400 x 1050 82.28 74.87 1400 x 1050 1400 x 1050
WSXGA+60 1680 x 1050 65.29 59.95 1400 x 875 1400 x 900 *3
UXGA60 1600 x 1200 75.00 60.00 1400 x 1050 1400 x 1050 *2, *3
Specifi cation of RGB signals in each computer mode of the projector
*1: The EXPAND mode and the PinP mode doesn’t function
with this signal.
*2: Available with the signal for the DVI-D terminal.
*3: The PinP mode doesn’t function with this signal.
Specifi cations (continued)
Signal mode Resolution Horizontal Vertical Normal mode Real mode
(H x V) frequency (kHz) frequency (Hz) (H x V) (H x V)
EN-46 1 R(RED)/CR 2 G(GREEN)/Y 3 B(BLUE)/CB 4 GND 5 GND 6 GND 7 GND 8 GND 9 DDC 5V (*1) 10 GND 11 GND 12 DDC Data (*1) 13 HD/CS 14 VD 15 DDC Clock (*1) 1 - - 2 TXD IN 3 RXD OUT 4 - - 5 GND - 6 - - 7 - - 8 - - 9 - - 1 5 116 10 15SERIAL (D-SUB 9-pin) Pin No. Name I/O COMPUTER/COMPONENT VIDEO IN-1/IN-2 (Mini D-SUB 15-pin) Pin No. Spec. DVI-D (HDCP) (DVI-D 24-pin) Pin No. Spec. Pin No. Spec. 1 TMDS DATA 2- 13 - 2 TMDS DATA 2+ 14 +5V Power 3 TMDS DATA 2 Shield 15 Ground (for +5V) 4 - 16 Hot Plug Detect 5 - 17 TMDS DATA 0- 6 DDC Clock 18 TMDS DATA 0+ 7 DDC Data 19 TMDS DATA 0 Shield 8 - 20 - 9 TMDS DATA 1- 21 - 10 TMDS DATA 1+ 22 TMDS Clock Shield 11 TMDS DATA 1 Shield 23 TMDS Clock+ 12 - 24 TMDS Clock- 1724 169 8 1 Connectors 333 59.5 125 84.5 331 272 Dimension Drawings (unit: mm) Specifi cations (continued) 1 5 6 9 (*1 For IN-1 terminal only. ) Specifi cation of RGB signals in each computer mode of the projector (continued) Important: • Some computers aren’t compatible with the projector. • The projector’s maximum resolution is 1400 x 1050 pix- els. It may not display images of higher resolutions than 1400 x 1050 correctly. • Images with SYNC on G (Green) signal may jitter. • Images with SYNC on G (Green) signal may be tinged with green. • If the resolution and frequency of your computer aren’ t shown on the table, fi nd the compatible resolution and frequency by changing the resolution of your computer. • TV60 and TV50 are equivalent to 480i and 576i respectively. When these signals are supplied to the VIDEO IN or S-VIDEO IN terminal, the signal mode is indicated as TV60 or TV50. When they are supplied to the COMPUTER IN/COMPONENT VIDEO IN terminals, the signal mode is indicated as 480i or 576i. • This projector doesn’t support 480p signals from video devices having 4 lines (R, G, B, CS*) or having 5 lines (R, G, B, H, V). * : Composite Sync• When a certain signal such as SXGA85 and SXGA85b is input, the number of displayed colors may decrease depending on the setting of ASPECT in the FEATURE menu. Change the signal format of the computer, if necessary. REAL modeWhen moire patterns or lines of uneven thickness appear on the projected image, these symptoms may be improved by displaying it in its original image size (REAL mode). To display the image in the REAL mode, set ASPECT of the FEATURE menu to REAL. (See page 23 for menu setting.) • In the REAL mode, you cannot change the magnifi cation factor and magnifi cation range. • For signals that are larger than the panel resolution, only their center part is displayed in the REAL mode. The area exceeding the panel resolution isn ’t displayed. • In the REAL mode, images are black-framed when the image resolution is lower than 1400 x 1050.
1 Zusho Baba, Nagaokakyo-City, Kyoto Japan MITSUBISHI ELECTRIC CORPORATION A Mitsubishi Projector Warranty, Sales Support and Service Information North AmericaMDEA (Mitsubishi Digital Electronics America, Inc.) Presentation Products Division 9351 Jeronimo Road Irvine CA 92618, USA For Warranty Registration, visit: http://www.mitsubishi-presentations.com under Customer CareSales & Inquiries Phone :Toll Free (888)307-0349 E-mail :[email protected] Technical Inquiries Phone :Toll Free (888)307-0309 E-mail :[email protected] MESCA (Mitsubishi Electric Sales Canada Inc.) http://www.mitsubishielectric.ca Information Technologies Group, 4299 14th Avenue, Markham, Ontario L3R 0J2, Canada Sales & Technical Inquiries Phone :+1-(800) 450-6487 Fax :+1-(905) 475-7958 E-mail :[email protected] Customer Care E-mail :[email protected] EuropeMEU-FRA (Mitsubishi Electric Europe B.V French Branch) 25, Boulevard des Bouvets 92 741, Nanterre CEDEX, France Sales Inquiries Phone :+33 (0)1 55-68-55-53 Fax :+33 (0)1 55-68-57-31 Technical Inquiries Phone :+33 (0)1 55-68-56-42 Fax :+33 (0)1 55-68-57-31 MEU-GER (Mitsubishi Electric Europe B.V. German Branch) http://www.mitsubishi-evs.de/ Gothaer Strasse 8, 40880 Ratingen, Germany Sales Inquiries Phone :0049 - 2102 - 486 9250 Fax :0049 - 2102 - 486 7320 Technical Inquiries Phone :0049 - 2102 - 486 1330 Fax :0049 - 2102 - 486 1340 MEU-IR (Mitsubishi Electric Europe B.V. Irish Branch) http://www.mitsubishi.ie/ Westgate Business Park, Ballymount, Dublin 24, Ireland Sales Inquiries Phone :+353-1-4198807 Fax :+353-1-4198890 Technical Inquiries Phone :+353-1-4198808 Fax :+353-1-4198895 MEU-IT (Mitsubishi Electric Europe B.V. Italian Branch) Centro Direzionale Colleoni, Palazzo Sirio, Viale Colleoni 7, 20041 Agrate Brianza, Italy Sales & Technical Inquiries Phone :+39-(0)39-60531 Fax :+39-(0)39-6053214 E-mail :[email protected] MEU-NL (Mitsubishi Electric Europe B.V. Benelux Branch) http://www.mitsubishi.nl/LCD/ProdFrame.html Nijverheidsweg 23A, 3641 RP Mijdrecht, The Netherlands Sales Inquiries Phone :+31-297-282461 Fax :+31-297-283936 E-mail :[email protected] Technical Inquiries Phone :+31-297-282461 Fax :+31-297-283936 E-mail :[email protected] Russia (Mitsubishi Electric Europe B.V Moscow Representative Offi ce) http://www.mitsubishi-projector.ru/ Moscow Representative Offi ce, 52/5 Kosmodamianskaya Nab., 115054, Moscow, Russia Sales & Technical Inquiries Phone :(7095) 721-2068 Fax :(7095) 721-2071 MEU-SP (Mitsubishi Electric Europe B.V. Spanish Branch) http://www.mitsubishielectric.es/ Ctra. de Rubi, 76-80, 08173 Sant Cugat del Valles, Barcelona, Spain Sales Inquiries Phone :+34-93.565.31.54 Fax :+34-93.589.43.88 E-mail :[email protected] Technical Inquiries Phone :+34-93.586.27.51 Fax :+34-93.588.53.87 E-mail :[email protected] MEU-SWE (Mitsubishi Electric Europe B.V Scandinavian Branch) Hammarbacken 14, Box 750, S-19127, Sollentuna, Sweden Sales Inquiries Phone :+46-(0)8-6251070 Fax :+46-(0)8-6251036 Technical Inquiries Phone :+46-(0)8-6251052 Fax :+46-(0)8-6251036 MEU-UK (Mitsubishi Electric Europe) http://www.mitsubishi.co.uk/evs/ Visual Information Systems Division, Travellers Lane, Hatfi eld, Hertfordshire, AL10 8XB U.K. Sales Inquiries Phone :+44 (1707) 278684 Fax :+44 (1707) 278541 E-mail :[email protected] Technical Inquiries Phone :+44 (870) 606 5008 Fax :+44 (1506) 431927 E-mail :[email protected] AsiaCHINA (Mitsubishi Electric Air-Conditioning & Visual Information Systems (Shanghai) Ltd.) 12/F., Hong Kong New World Tower, 300 Huaihai Middle Road, Shanghai, 200021, China Sales Inquiries Phone :+86(21)6335-3030 (Ext. 3007) Fax :+86(21)6335-3600 Technical Inquiries Phone :+86(21)6335-3030 (Ext. 3021) Fax :+86(21)6335-3600 HONG KONG (Mitsubishi Electric Ryoden Air-Conditioning & Visual Information Systems (HongKong) Ltd.) 7th Floor, Manulife Tower, 169 Electric Road, North Point, Hong Kong Sales Inquiries Phone :+852-2510-1505 Fax :+852-2510-0463 Technical Inquiries Phone :+852-2422-0161 Fax :+852-2487-0181 SINGAPORE (Mitsubishi Electric Asia Pte. Ltd.) http://www.mitsubishielectric.com.sg 307, Alexandra Road, #05-01/02 Mitsubishi Electric Building, Singapore 159943 Sales Inquiries Phone :+65-6473-2308 Fax :+65-6475-9503 E-mail :[email protected] Technical Inquiries Phone :+65-6470-2666 Fax :+65-6475-9503 INDIA (Mitsubishi Electric Asia Pte. Ltd.) 307, Alexandra Road, #05-01/02 Mitsubishi Electric Building, Singapore 159943 Sales Inquiries Phone :+65-6473-2308 Fax :+65-6475-9503 E-mail :[email protected] Technical Inquiries Phone :+65-6470-2666 Fax :+65-6475-9503 INDONESIA (Mitsubishi Electric Asia Pte. Ltd.) 307, Alexandra Road, #05-01/02 Mitsubishi Electric Building, Singapore 159943 Sales Inquiries Phone :+65-6473-2308 Fax :+65-6475-9503 E-mail :[email protected] Technical Inquiries Phone :+65-6470-2666 Fax :+65-6475-9503 PHILIPPINES (Mitsubishi Electric Asia Pte. Ltd.) http://www.mitsubishielectric.com.sg 307, Alexandra Road, #05-01/02 Mitsubishi Electric Building, Singapore 159943 Sales Inquiries Phone :+65-6473-2308 Fax :+65-6475-9503 E-mail :[email protected] Technical Inquiries Phone :+65-6470-2666 Fax :+65-6475-9503 VIETNAM (Mitsubishi Electric Asia Pte. Ltd.) 307, Alexandra Road, #05-01/02 Mitsubishi Electric Building, Singapore 159943 Sales Inquiries Phone :+65-6473-2308 Fax :+65-6475-9503 E-mail :[email protected] Technical Inquiries Phone :+65-6470-2666 Fax :+65-6475-9503 STC (Setsuyo Astec Corporation Seoul Branch) 4F,Dongseo Game Channel Bldg,660-11 Deungchon-Dong, Kangseo-Ku, Seoul, Korea Sales & Technical Inquiries Phone :+82-(0)2-2657-9841~3 Fax :+82-(0)2-2657-9900 MALAYSIA (Antah Melco Sales & Services Sdn. Bhd.) 6, Jalan 13/6 46860 Petaling Jaya Selangor, Darul Ehsan, Malaysia Sales & Technical Inquiries Phone :+60-(0)3-79552088 (Ext. 203) Fax :+60-(0)3-79563950/+60-(0)3-79582576 Technical & Service Inquiries Phone :+60-(0)3-79552088 (Ext. 106) Fax :+60-(0)3-79563950/+60-(0)3-79582576 ME-TWN (Mitsubishi Electric Taiwan Co., Ltd.) http://www.MitsubishiElectric.com.tw 11TH FL., 90 SEC. 6, CHUNG SHAN N. RD., TAIPEI, 111 R.O.C. Sales & Technical Inquiries Phone :+886-2-2832-8255 Fax :+886-2-2833-9813 MKY (Mitsubishi Electric Kang Yong Watana Co., Ltd. ) http://www.mitsubishi-kyw.co.th/ Road, Huamark Bangkapi, Bangkok 10240, Thailand Sales & Technical Inquiries Phone :+66-2-731-6841 Fax :+66-2-379-4763 OceaniaME-AUST (Mitsubishi Electric Australia) http://www.mitsubishi-electric.com.au/prod.asp?prod=proj 348 Victoria Road, Rydalmere, N.S.W. 2116, Australia Sales & Technical Inquiries Phone :+(612)9684-7777 Fax :+(612)9684-7208 E-mail :[email protected] Technical Inquiries Phone :+(612)9684-7694 Fax :+(612)9684-7684 E-mail :[email protected] BDT (Black Diamond Technologies Ltd.) (Warranty Registration) http://www.bdt.co.nz/projectors/ warranty.asp 1 Parliament St, Lower Hutt, Wellington, New Zealand Sales Inquiries Phone :+64-(0)4-560-9100 Fax :+64-(0)4-560-9133 E-mail :[email protected] Technical Inquiries Phone :+64-(0)4-560-9100 Fax :+64-(0)4-560-9133 E-mail :[email protected]