Mitsubishi Mdt321s Users Manual

							1-21 
English-19
English
MAIN MENUPICTURE
SCREEN
AUDIO
PIP
CONFIGURATION 1
CONFIGURATION 2
ADVANCED OPTION
:SELSET:NEXT:RETURNMENU:EXIT MENU
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
BLACK LEVEL
COLOR CONTROL
COLOR TEMPERATURE
PICTURE RESET
:SELSET:NEXTEXIT:RETURNMENU:EXIT MENU
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
BLACK LEVEL
COLOR CONTROL
COLOR TEMPERATURE
PICTURE RESET
:SELSET:NEXT:RETURNMENU:EXIT MENU+ -:ADJ:RETURNMENU:EXIT MENU
32BRIGHTNESS
EXITEXITEXIT
OSD (On-Screen-Display) Controls
Press MENU button to
open Main menu.
Press UP or DOWN button
to select sub-menu.Press SET button to
decide.Press UP or DOWN, and PLUS or
MINUS button to select function, or
control which you like.
Press SET button to decide.Press MENU or EXIT
button to exit.
Remote Control
Press UP or DOWN
button to select.Press INPUT button
to decide.Press UP or DOWN, and PLUS or
MINUS button to select function, or
control which you like.
Press INPUT button to decide.Press EXIT button
to exit.
Control Panel
UP or DOWN buttonINPUT button
OSD screen
Main-Menu
PICTURE
Sub-Menu
Adjusts the overall image and background screen
brightness.
Press + button to increase brightness.
Press - button to decrease brightness.
Adjusts the image contrast in relation to the input
signal.
Press + button to increase contrast.
Press - button to decrease contrast.
NOTE: sRGB picture mode is standard and cannot
be changed.
This function is digitally capable to keep crisp image at
any timing. It is adjustable to get a distinct image or a
soft one as you prefer and set independently for each
picture mode.
Press + button to increase sharpness.
Press - button to decrease sharpness.
Adjusts the image brightness in relation to the
background.
Press + button to increase black level.
Press - button to decrease black level.
NOTE: sRGB picture mode is standard and cannot be
changed.
Adjusts the noise reduction level.
Press + button to increase reduction level.
Press - button to decrease reduction level.
BRIGHTNESS
CONTRAST
SHARPNESS
BLACK LEVEL
NOISE REDUCTION
*:INPUT VIDEO  only
MAIN MENUPICTURE
SCREEN
AUDIO
PIP
CONFIGURATION 1
CONFIGURATION 2
ADVANCED OPTION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
TINT
COLOR
BLACK LEVEL
NOISE REDUCTION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
32NOISE REDUCTION
EXIT
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
BLACK LEVEL
COLOR CONTROL
COLOR TEMPERATURE
PICTURE RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
32BLACK LEVEL
EXIT
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
BLACK LEVEL
COLOR CONTROL
COLOR TEMPERATURE
PICTURE RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
12SHARPNESS
EXIT
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
BLACK LEVEL
COLOR CONTROL
COLOR TEMPERATURE
PICTURE RESET
:SELSET:NEXTEXIT:RETURNMENU:EXIT MENU
CONTRAST
+ -:ADJ :RETURNMENU:EXIT MENU
32
EXIT
+ -:ADJEXIT:RETURNMENU:EXIT MENU
32BRIGHTNESSPICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
BLACK LEVEL
COLOR CONTROL
COLOR TEMPERATURE
PICTURE RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
 
						

							1-22 
English-20
Adjust the tint of the screen.
Press + button to Skin color becomes greenish.
Press - button to Skin color becomes purplish.
Adjust the color depth of the screen.
Press + button to increase color depth.
Press - button to decrease color depth.
R, G, B: Increases or decreases Red, Green and Blue,
depending upon which is selected. The change in color
will appear on screen and the direction (increase or
decrease) will be shown by the color bars.
NOTE: sRGB picture mode is standard and cannot be
changed.
To adjust the color temperature of entire screen.
Adjusting lower color temperature makes the screen
reddish and higher color temperature makes the screen
bluish.
NOTE: sRGB picture mode is standard and cannot be
changed.
Selecting Picture reset allows you to reset all OSD
settings about PICTURE setting.
Select “Yes” and press “SET” button to restore to factory
preset data.
Press “EXIT” button to cancel and then return to the
previous menu.
TINT
*:INPUT DVD/HD, VIDEO only
COLOR
*:INPUT DVD/HD, VIDEO only
COLOR CONTROL
*:INPUT RGB1,2,3 only
COLOR
TEMPERATURE
PICTURE RESET
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
BLACK LEVEL
COLOR CONTROL
COLOR TEMPERATURE
PICTURE RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
PICTURE RESET
:RETURNMENU:EXIT MENU
NO
YES
:SELEXIT
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
BLACK LEVEL
COLOR CONTROL
COLOR TEMPERATURE
PICTURE RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
9600KCOLOR TEMPERATURE
EXIT
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
BLACK LEVEL
COLOR CONTROL
COLOR TEMPERATURE
PICTURE RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJEXIT:RETURN
COLOR CONTROL
255
:SEL
RED
255 GREEN255 BLUE
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
TINT
COLOR
BLACK LEVEL
NOISE REDUCTION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
32COLOR
EXIT
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
TINT
COLOR
BLACK LEVEL
NOISE REDUCTION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
32TINT
EXIT
Main-Menu
SCREEN
Sub-Menu
Controls Horizontal Image position within the display
area of the LCD.
Press + button to move screen to right.
Press - button to move screen to left.
Controls Vertical Image position within the display
area of the LCD.
Press + button to move screen to UP.
Press - button to move screen to DOWN.
Press + button to expand the width of the image on
the screen to the right.
Press - button to narrow the width of the image on the
screen to the left.
Improves focus, clarity and image stability by increasing
or decreasing this setting.
Adjusts the horizontal size by increasing or decreasing
the setting.
Press + button to expand the width of the image on
the screen.
Press - button to narrow the width of the image on
the screen.
H POSITION
V POSITION
CLOCK
*:INPUT RGB2/3 only
CLOCK PHASE
*:INPUT RGB2/3, DVD/HD only
H RESOLUTION
*:INPUT RGB1/2/3 only
MAIN MENU
PICTURE
SCREEN
AUDIO
PIP
CONFIGURATION 1
CONFIGURATION 2
ADVANCED OPTION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
SCREEN
H POSITION
V POSITION
CLOCK
CLOCK PHASE
H RESOLUTION
V RESOLUTION
ZOOM MODE
SCREEN RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
1360H RESOLUTION
EXIT
SCREEN
H POSITION
V POSITION
CLOCK
CLOCK PHASE
H RESOLUTION
V RESOLUTION
ZOOM MODE
SCREEN RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
18CLOCK PHASE
EXIT
SCREEN
H POSITION
V POSITION
CLOCK
CLOCK PHASE
H RESOLUTION
V RESOLUTION
ZOOM MODE
SCREEN RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
1782CLOCK
EXIT
SCREEN
H POSITION
V POSITION
CLOCK
CLOCK PHASE
H RESOLUTION
V RESOLUTION
ZOOM MODE
SCREEN RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
10V POSITION
EXIT
+ -:ADJ :RETURNMENU:EXIT MENU
10H POSITION
EXIT
SCREENH POSITION
V POSITION
CLOCK
CLOCK PHASE
H RESOLUTION
V RESOLUTION
ZOOM MODE
SCREEN RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
 
						

							1-23 
English-21
English
Adjusts the vertical size by increasing or decreasing the
setting.
Press + button to expand the height of the image on the
screen.
Press - button to narrow the height of the image on
the screen.
Selects the screen zoom mode. Zoom mode will be
selected when you select the “ZOOM” by pushing the
“SIZE” button on remote controller.
When you select the “CUSTOM”, you will be able to
adjust optional horizontal and vertical size.
You can also select 16:9, 14:9 and DYNAMIC.
(INPUT DVD/HD,VIDEO only)
Press “SET” button to show a control menu as follows:
Increase or decrease “ZOOM” slider to adjust the whole
size and then adjust horizontal and vertical size by
H ZOOM and V ZOOM. Increase or decrease “H POS”
and “V POS” to adjust the picture position.
Selecting “DYNAMIC” will expand 4:3 pictures to the
entire screen with non-linearity. (Some around image
will be cut by expansion.) Dynamic image is the same
as FULL size image when HDTV 1080i or 720p signal
is input.
Selecting “OFF" image will be displayed 1 by 1 pixel.
(If you input over 1366x768 resolution signal, it will be
displayed as shrank image.)
Selecting Screen reset allows you to reset all OSD
settings from SCREEN setting.
Select “Yes” and press “SET” button to restore the
factory preset data.
Press “EXIT” button to cancel and then return to the
previous menu.
V RESOLUTION
*:INPUT RGB1/2/3 only
ZOOM MODE
SCREEN
H POSITION
V POSITION
CLOCK
CLOCK PHASE
H RESOLUTION
V RESOLUTION
ZOOM MODE
SCREEN RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
SCREEN RESET
:RETURNMENU:EXIT MENU
NO
YES
:SELEXIT
CUSTOM
:SEL + - :ADJ :RETURNMENU:EXIT MENU
X 1.00
X 1.00
X 1.00
0%
0%ZOOM
H ZOOM
V ZOOM
H POS
V POS
EXIT
ZOOM MODE
CUSTOMV
16:9
14:9
DYNAMIC
OFF
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
SCREEN
H POSITION
V POSITION
CLOCK
CLOCK PHASE
H RESOLUTION
V RESOLUTION
ZOOM MODE
SCREEN RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
SCREEN
H POSITION
V POSITION
CLOCK
CLOCK PHASE
H RESOLUTION
V RESOLUTION
ZOOM MODE
SCREEN RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
768V RESOLUTION
EXIT
SCREEN RESET
ZOOM MODE
CUSTOM
OFF
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
*:INPUT DVD/HD, VIDEO only*:INPUT RGB1/2/3 only
Main-Menu
AUDIO
Sub-Menu
Adjust the balance of L/R volume.
Press + button to move the stereo sound image to right.
Sound of the left side will be small.
Press - button to move the stereo sound image to left.
To accentuate or reduce the high frequency sound.
Press + button to increase TREBLE sound.
Press - button to decrease TREBLE sound.
To accentuate or reduce the low frequency sound.
Press + button to increase BASS sound.
Press - button to decrease BASS sound.
Selecting Audio reset allows you to reset all OSD
settings from AUDIO setting.
Select “Yes” and press “SET” button to restore the
factory preset.
Press “EXIT” button to cancel and then return to the
previous menu.
BALANCE
TREBLE
BASS
AUDIO RESET
MAIN MENU
PICTURE
SCREEN
AUDIO
PIP
CONFIGURATION 1
CONFIGURATION 2
ADVANCED OPTION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
AUDIO
BALANCE
TREBLE
BASS
AUDIO RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
AUDIO RESET
:RETURNMENU:EXIT MENU
NO
YES
:SELEXIT
AUDIO
BALANCE
TREBLE
BASS
AUDIO RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
0BASS
EXIT
AUD IO
BALANCE
TREBLE
BASS
AUDIO RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
0TREBLE
EXIT
+ -:ADJ :RETURNMENU:EXIT MENU
RBALANCEL
EXIT
AUD IO
BALANCE
TREBLE
BASS
AUDIO RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
 
						

							1-24 
English-22
Main-Menu
PICTURE IN PICTURE
Sub-Menu
Selecting the size of picture inserted at the
“Picture-in-Picture” (PIP) mode.
“Large”, “Middle” and “Small” are available.
Selecting the sound source in PIP mode.
When selecting “MAIN AUDIO”, you will get the sound
for the main picture and when selecting “PIP AUDIO”,
you will get the sound for the picture instead.
Selecting PIP Reset allows you to reset all OSD
settings from PIP setting.
Select “Yes” and press “SET” button to restore the
factory preset data.
Press “EXIT” button to cancel and then return to the
previous menu.
PIP SIZE
PIP AUDIO
PIP RESET
MAIN MENU
PICTURE
SCREEN
AUDIO
PIP
CONFIGURATION 1
CONFIGURATION 2
ADVANCED OPTION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
PIP
PIP SIZE
PIP AUDIO
PIP RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
PIP RESET
:RETURNMENU:EXIT MENU
NO
YES
:SELEXIT
PIP
PIP SIZE
PIP AUDIO
PIP RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT:RETURNMENU:EXIT MENU
PIP AUDIO
MAIN AUDIO           /             PIP AUDIO
EXIT+ -:SEL
:RETURNMENU:EXIT MENU
PIP SIZELARGE
MIDDLE
SMALL
:SELEXIT
PIP
PIP SIZE
PIP AUDIO
PIP RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
Main-Menu
CONFIGURATION 1
Sub-Menu
Press “SET” button to automatically adjust screen size,
horizontal position, vertical position, clock, clock phase,
white level and black level.
Press “EXIT” button to cancel execution AUTO SETUP
and then will return to the previous menu.
Selecting the auto adjust ON/OFF.
Selecting ON when changing the timing, the horizontal
position, vertical position and clock-phase will adjust
automatically according to input signal.
Selecting the auto brightness ON/OFF.
When select “ON”, the brightness will be automatically
adjusted.
Selecting RGB “ON”, the monitor will go to power
management mode when RGB1,2,3 sync is lost.
Selecting VIDEO “ON”, the monitor will go to power
management mode after about 10 minutes delay from
when DVD/HD and VIDEO input signal is lost.
OSD control menus are available in seven languages.
AUTO SETUP
*:INPUT RGB2/3 only
AUTO ADJUST
*:INPUT RGB2/3 only
AUTO BRIGHTNESS
*:INPUT RGB1/2/3 only
POWER SAVE
LANGUAGE
MAIN MENU
PICTURE
SCREEN
AUDIO
PIP
CONFIGURATION 1
CONFIGURATION 2
ADVANCED OPTION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
CONFIGURATION 1
AUTO SETUP
AUTO ADJUST
AUTO BRIGHTNESS
POWER SAVE
LANGUAGE
SCREEN SAVER
SIDE BORDER COLOR
:SELSET:NEXT :RETURNMENU:EXIT MENUEXITEXIT
LANGUAGE
ENGLISH
DEUTSCH
FRANCAIS
ESPAÑOL
ITALIANO
SVENSKA
CONFIGURATION 1
AUTO SETUP
AUTO ADJUST
AUTO BRIGHTNESS
POWER SAVE
LANGUAGE
SCREEN SAVER
SIDE BORDER COLOR
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
POWER SAVERGB         ON/             OFFVIDEO ON /             OFF
:SELEXIT
CONFIGURATION 1
AUTO SETUP
AUTO ADJUST
AUTO BRIGHTNESS
POWER SAVE
LANGUAGE
SCREEN SAVER
SIDE BORDER COLOR
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT:RETURNMENU:EXIT MENU
AUTO BRIGHTNESS
ON/             OFF
EXIT+ -:SEL
CONFIGURATION 1
AUTO SETUP
AUTO ADJUST
AUTO BRIGHTNESS
POWER SAVE
LANGUAGE
SCREEN SAVER
SIDE BORDER COLOR
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT:RETURNMENU:EXIT MENU
AUTO ADJUST
ON/             OFF
EXIT+ -:SEL
:CANCELMENU:EXIT MENU
AUTO SETUP
SETPRESS
TO   RESET
:RESETSETEXIT
CONFIGURATION 1
AUTO SETUP
AUTO ADJUST
AUTO BRIGHTNESS
POWER SAVE
LANGUAGE
SCREEN SAVER
SIDE BORDER COLOR
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
 
						

							1-25 
English-23
English
Select “SCREEN SAVER” functions to reduce the risk of
the “image persistence”.
GAMMA: The display gamma is changed and fixed when
selected “ON”.
COOLING FAN: The built in cooling fan is always on
when set “ON”.
BRIGHTNESS: The brightness is decreased when
selected “ON”.
MOTION: Image is slightly expanded and moves
4 directions (UP, DOWN, RIGHT, LEFT) periodically
(Need setting the time for movement).
Movement area is approximately +/- 10mm from original
position; Please locate the important information such as
text within 90% area of screen image.
See note (1) for this functions.
PIP and STILL will be disabled when “MOTION” is active.
Selecting the Color System depends on your input video
format.
AUTO: NTSC, PAL, SECAM, PAL60 or 4.43 NTSC is
automatically selected.
NTSC: Specific selection of NTSC.
PAL: Specific selection of PAL.
SECAM: Specific selection of SECAM.
PAL-60: Specific selection of PAL60.
4.43NTSC: Specific selection of 4.43 NTSC.
Adjustment the side black bar color white when 4:3
image displayed, black to white.
Press + button, the bar will become whiter.
Press - button, the bar will become darker.
Selecting the CONFIGURATION RESET allows you to
reset all configuration settings.
Select “Yes” and press “SET” button to restore the factory
preset data.
Press “EXIT” button to cancel and return the previous
menu.
Selecting “YES” allows you to reset PICTURE, SCREEN,
AUDIO, CONFIGURATION1,2 and ADVANCED OPTION
will be back to factory settings (except LANGUAGE,
DATE & TIME and SCHEDULE).
Select “YES” and press “SET” button to restore the
factory preset data.
Press “EXIT” button to cancel and return the previous
menu.
SCREEN SAVER
COLOR SYSTEM
*:INPUT VIDEO  only
SIDE BORDER
COLOR
CONFIGURATION
RESET
FACTORY RESET
CONFIGURATION 1
POWER SAVE
LANGUAGE
SCREEN SAVER
COLOR SYSTEM
SIDE BORDER COLOR
CONFIGURATION RESET
FACTORY RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
FACTORY RESET
:RETURNMENU:EXIT MENU
NO
YES
:SELEXIT
CONFIGURATION 1
POWER SAVE
LANGUAGE
SCREEN SAVER
COLOR SYSTEM
SIDE BORDER COLOR
CONFIGURATION RESET
FACTORY RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
CONFIGURATION RESET
:RETURNMENU:EXIT MENU
NO
YES
:SELEXIT
CONFIGURATION 1
AUTO SETUP
AUTO ADJUST
AUTO BRIGHTNESS
POWER SAVE
LANGUAGE
SCREEN SAVER
SIDE BORDER COLOR
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJEXIT:RETURN
SCREEN SAVER
:SEL
GAMMA
  COOLING FAN
  BRIGHTNESS
  MOTIONON    /    OFF
ON    /AUTO
ON    /    OFF
      10  SEC.
CONFIGURATION 1
POWER SAVE
LANGUAGE
SCREEN SAVER
COLOR SYSTEM
SIDE BORDER COLOR
CONFIGURATION RESET
FACTORY RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
COLOR SYSTEM
AU TODEUTSCH
NTSC
PA L
SECAM
4.43 NTSC
PAL-60
:SEL :RETURNMENU:EXIT MENUEXIT
CONFIGURATION 1
AUTO BRIGHTNESS
POWER SAVE
LANGUAGE
POWER SAVE
COLOR SYSTEM
SIDE BORDER COLOR
CONFIGURATION RESET
FACTORY RESET
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT+ -:ADJ :RETURNMENU:EXIT MENU
50SIDE BORDER COLOR
EXIT
Main-Menu
CONFIGURATION 2
Sub-Menu
To compensate for image degradation, which is caused by
using a long cable.
VIDEO EQ
To optimize the shape (Tailing) of RED, GREEN and
BLUE signal.
Level: 0 - 7
SYNC TERMINATE (Input RGB 3 only)
To select the terminate resistance for matching the cable
impedance.
HI: 2.2K ohm/LO:75 ohm
LONG CABLE
MANUAL
*:INPUT RGB2/3 only
MAIN MENU
PICTURE
SCREEN
AUDIO
PIP
CONFIGURATION 1
CONFIGURATION 2
ADVANCED OPTION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
CONFIGURATION 2
LONG CABLE MANUAL
OSD TURN  OFF
INFORMATION OSD
OFF TIMER
OSD POSITION
INPUT DETECT
MONITOR INFORMATION
:SELSET:NEXTEXIT:RETURNMENU:EXIT MENU
LONG CABLE MANUAL
VIDEO EQ.
SYNC TERMINATE
:SELNEXT:RETURN
+ -:ADJ           0
HI  /  LO
 
						

							1-26 
English-24
The OSD control menu will stay on as long as it is use.
In the OSD Turn Off submenu, you can select how long
the monitor waits after the last touch of a button to shut
off the OSD control menu. The preset choices are
10 -240 seconds.
Selects the information OSD display or not. The
information OSD will display when input signal or
source change or warning message like as no-signal or
out-of range.
A time between 3 to 10 seconds is available.
To select OFF TIMER mode ON/OFF.
In the OFF TIMER menu, you can preset the monitor to
automatically power down.
A time between 1 to 24 hours is available.
When the OFF TIMER is set, the SCHEDULE
(see page 26) settings will be disabled.
Adjusts the position of the OSD menu.
Selects the method of input detection when more than
two computers are connected.
FIRST DETECT:  When the current video input signal is
not present, then the monitor searches for a video signal
from the other video input port. If the video signal is
present in the other port, then the monitor switches the
video source input port to the new found video source
automatically. The monitor will not look for other video
signals while the current video source is present.
This function is available at input RGB 1/2/3.
LAST DETECT:  When the monitor is displaying a signal
from the current source and a new secondary source is
supplied to the monitor, the monitor will automatically
switch to the new video source. When current video input
signal is not present, the monitor searches for a video
signal from the other video input port. If the video signal
is present in the other port, then the monitor switches the
video source input port to the new found video source
automatically.
This function is available at input RGB 1/2/3.
VIDEO DETECT: DVD/HD or VIDEO inputs will have
priority over RGB1/2/3. When DVD/HD or VIDEO input
signal is present the monitor will change and keep to the
DVD/HD or VIDEO input.
NONE: The Monitor will not search the other video input
port.
Indicates the model and serial number of your monitor.
OSD TURN  OFF
INFORMATION OSD
OFF TIMER
OSD POSITION
CONFIGURATION 2
LONG CABLE MANUAL
OSD TURN  OFF
INFORMATION OSD
OFF TIMER
OSD POSITION
INPUT DETECT
MONITOR INFORMATION
:SELSET:NEXTEXIT:RETURNMENU:EXIT MENUEXIT:RETURN
OFF TIMERON            1   HOUR
OFF
+ -:ADJ:SEL
CONFIGURATION 2
LONG CABLE MANUAL
OSD TURN  OFF
INFORMATION OSD
OFF TIMER
OSD POSITION
INPUT DETECT
MONITOR INFORMATION
:SELSET:NEXTEXIT:RETURNMENU:EXIT MENUEXIT:RETURN
INFORMATION OSDON                 10 SEC.
OFF
+ -:ADJ:SEL
CONFIGURATION 2
LONG CABLE MANUAL
OSD TURN  OFF
INFORMATION OSD
OFF TIMER
OSD POSITION
INPUT DETECT
MONITOR INFORMATION
:SELSET:NEXTEXIT:RETURNMENU:EXIT MENU+ -:ADJ :RETURNMENU:EXIT MENU
OSD TURN  OFF
10 SEC.
EXIT
CONFIGURATION 2
LONG CABLE MANUAL
OSD TURN  OFF
INFORMATION OSD
OFF TIMER
OSD POSITION
INPUT DETECT
MONITOR INFORMATION
:SELSET:NEXTEXIT:RETURNMENU:EXIT MENU
OSD POSITIONH POSITION
V POSITION50
70EXIT:RETURN + -:ADJ:SEL
INPUT DETECT
MONITOR
INFORMATION
CONFIGURATION 2
LONG CABLE MANUAL
OSD TURN  OFF
INFORMATION OSD
OFF TIMER
OSD POSITION
INPUT DETECT
MONITOR INFORMATION
:SELSET:NEXTEXIT:RETURNMENU:EXIT MENU:RETURNMENU:EXIT MENU
INPUT DETECTFIRST
LAST
VIDEO
NONEDETECT
DETECT
DETECT
:SELEXIT
CONFIGURATION 2
LONG CABLE MANUAL
OSD TURN  OFF
INFORMATION OSD
OFF TIMER
OSD POSITION
INPUT DETECT
MONITOR INFORMATION
:SELSET:NEXTEXIT:RETURNMENU:EXIT MENU:RETURNMENU:EXIT MENU
MONITOR INFORMATIONMODEL  NAME:
     MDT321S
SERIAL:
   12315XXX
EXIT
 
						

							1-27 
English-25
English
Main-Menu
ADVANCED OPTION
Sub-Menu
Selects the S-Video input port function.
PRIORITY:
If cable is connected to the S-Video input, it will have
priority the composite input port.
SEPARATE:
S-Video port and Composite port are selectable as
independent input port.
Selects to decision of input signal about below timings,
1024x768, 1280x768 and 1360x768.
AUTO: Determines the resolution automatically.
1024x768: Determines the resolution as 1024x768
1280x768: Determines the resolution as 1280x768
1360x768: Determines the resolution as 1360x768
Selects a level of black expansion.
In case of go under the black cut-off level, please adjust
the “Black level” in moderation on OSD menu.
Selects a display gamma.
    1: 2.2
    2: 2.4
    3: S gamma
    4: Native
NOTE: sRGB picture mode is standard and cannot be
changed.
Changes the display area of the image.
OVERSCAN: Set to display area about 95%
UNDERSCAN: Set to display area about 100%
Selects IP (Interlace to Progressive) converter function.
PROGRESSIVE: Enable the IP function, to convert
interlace signal to progressive. Normally use this setting.
INTERLACE*: Disable the IP function.
*NOTE: This mode is better suited for motion pictures,
but it is in danger of image retention.
Selects Film mode function.
AUTO: Enable the Film mode function. This mode is
better suited for movies, which is converted 24 Frames/
sec source to DVD Video. We recommend to select
“PROGRESSIVE” in “SCAN CONVERSION”.
OFF: Disable the Film mode function. This mode is
better suited for Broadcasting or VCR source.
Selects the infrared wireless remote controller mode.
The item in this menu will become effective by pressing
“SET” button on the selected item.
NORMAL: The monitor will be controlled normally by
wireless remote controller.
LOCK: Disable the monitor control by infrared wireless
remote controller.
Keep pressing “DISPLAY” button during 5 sec or more,
this setting will return to “NORMAL”.
S-VIDEO MODE
INPUT RESOLUTION
*:INPUT RGB2/3 only
BLACK LEVEL
EXPANSION
*:INPUT VIDEO, DVD/HD only
GAMMA SELECTION
MAIN MENU
PICTURE
SCREEN
AUDIO
PIP
CONFIGURATION 1
CONFIGURATION 2
ADVANCED OPTION
:SELSET:NEXT :RETURNMENU:EXIT MENUEXIT
S-VIDEO MODE 
BLACK LEVEL EXPANSION
GAMMA SELECTION
SCAN MODE
SCAN CONVERSION
FILM MODE
:SELSET:NEXTEXIT:RETURNMENU:EXIT MENU
ADVANCED OPTION
IR CONTROLBLACK LEVEL EXPANSIONHIGH
MIDDLE
OFF
EXIT:RETURNMENU:EXIT MENU:SEL
S-VIDEO MODE 
BLACK LEVEL EXPANSION
GAMMA SELECTION
SCAN MODE
SCAN CONVERSION
FILM MODE
:SELSET:NEXTEXIT:RETURNMENU:EXIT MENU
ADVANCED OPTION
IR CONTROL
:EXIT MENU:RETURNMENU
GAMMA SELECTION2.  2
2.  4
S  GAMMA
NATIVE
:SELEXIT:EXIT MENU
S-VIDEO MODE 
INPUT RESOLUTION
GAMMA SELECTION
SCAN CONVERSION
TILING
HEAT STATAS
:SELSET:NEXTEXIT:RETURNMENU:EXIT MENUIR CONTROL
ADVANCED OPTION
:RETURNMENU:EXIT MENU
S-VIDEO MODE
PRIORITY/           SEPARATE
+ -:SELEXIT
S-VIDEO MODE 
BLACK LEVEL EXPANSION
GAMMA SELECTION
SCAN MODE
SCAN CONVERSION
FILM MODE
:SELSET:NEXTEXIT:RETURNMENU:EXIT MENUTILING
ADVANCED OPTION
:RETURNMENU:EXIT MENU
INPUT RESOLUTION
:SEL
AU TO
1024 X 768
1280 X 768
1360 X 768
EXIT
S-VIDEO MODE 
BLACK LEVEL EXPANSION
GAMMA SELECTION
SCAN MODE
SCAN CONVERSION
FILM MODE
:SELSET:NEXTEXIT:RETURNMENU:EXIT MENU
ADVANCED OPTION
IR CONTROLMENU:EXIT MENU:RETURN
FILM MODEAUTO      /     OFF
+ -: SELEXIT
S-VIDEO MODE 
BLACK LEVEL EXPANSION
GAMMA SELECTION
SCAN MODE
SCAN CONVERSION
FILM MODE
:SELSET:NEXTEXIT:RETURNMENU:EXIT MENU
ADVANCED OPTION
IR CONTROL:RETURNMENU:EXIT MENU
SCAN MODEOVERSCAN      /   UNDERSCAN
+ -: SELEXIT
S-VIDEO MODE 
BLACK LEVEL EXPANSION
GAMMA SELECTION
SCAN MODE
SCAN CONVERSION
FILM MODE
:SELSET:NEXTEXIT:RETURNMENU:EXIT MENU
ADVANCED OPTION
IR CONTROL:RETURNMENU:EXIT MENU
SCAN CONVERSIONPROGRESSIVE/     INTERLACE
+ -: SELEXIT
ADVANCED OPTION
IR CONTROL
TILING
HEAT STATUS
POWER ON DELAY
DATE & TIME
SCHEDULE
ADVANCED OPTION RESET
:SELSET:NEXTEXIT:RETURNMENU:EXIT MENUEXITSET:RETURN :SET
IR CONTROL
:SEL
NORMAL
LOCK
SCAN MODE
*:INPUT DVD/HD, VIDEO only
SCAN CONVERSION
FILM MODE
*:INPUT DVD/HD, VIDEO only
IR CONTROL
 
						

							1-28 
English-26
TILING demonstrates multiple screens. This feature
provides a single large screen using up to 16 monitors.
It will be able to divide up to 4 each H and V.
This requires you to feed the PC output into each of the
monitors through a distributor.
H MONITORS: Select number of horizontal divide.
V MONITORS: Select number of vertical divide.
POSITION: Select a position to expand the screen.
FRAME COMP: Works in tandem with TILING to
compensate for the width of the tile bezels in order to
accurately display the image.
ENABLE: Select “YES”, the monitor will expand the
selected position.
PIP and STILL and “DYNAMIC” ZOOM mode will be
disabled when “TILING” is activated.
Information of status for COOLING FAN, BRIGHTNESS
and TEMPERATURE.
COOLING FAN comes to run when inside temperature
is over a guaranteed limit.
BRIGHTNESS comes to be decreased when inside
temperature is over guaranteed limit with cooling fun.
In this case warning is displayed on the screen.
Adjusts the delay time from “standby” to “power on”
mode.
“POWER ON DELAY” time is selectable between 0 and
50 sec.
Adjusts the current date and time for internal clock.
You should set this function when you use “SCHEDULE”.
Programs the monitor’s working schedule.
Schedule the power on and power off with hour and a day
of the week. Also sets the input port.
This OSD can’t remove except EXIT.
(see “NOTE 2” on page 27 for further information)
Selecting ADVANCED OPTION reset allows you to reset
all OSD settings from ADVANCED OPTION settings,
except for DATE & TIME, and SCHEDULE.
Select “YES” and press “SET” button to restore the
factory preset data.
Press “EXIT” button to cancel and then return the
previous menu.
TILING
ADVANCED OPTION
IR CONTROL
TILING
HEAT STATUS
POWER ON DELAY
DATE & TIME
SCHEDULE
ADVANCED OPTION RESET
:SELSET:NEXTEXIT:RETURNMENU:EXIT MENUEXIT:RETURN:SEL
H  MONITORS
V  MONITORS
POSITION
FRAME COMP
ENABLE1
1
1
YES   /      NO
YES   /      NOTILING
+ -:ADJ
HEAT STATUS
DATE & TIME
SCHEDULE
ADVANCED
OPTION RESET POWER ON DELAY
ADVANCED OPTION
IR CONTROL
TILING
HEAT STATUS
POWER ON DELAY
DATE & TIME
SCHEDULE
ADVANCED OPTION RESET
:SELSET:NEXTEXIT:RETURNMENU:EXIT MENUEXIT
:RETURNMENU:EXIT MENU
DATE & TIME
:SEL
YEAR
MONTH
DAY
TIME
DAYLIGHT SAVING     YES   /    NO
CURRENT DATE             TIME
    JAN. 01. 2004     00  :  00  :  002004
JANUARY
01
00:  00
:SET
+ -:ADJSETEXIT
:RETURNMENU:EXIT MENU
DATE & TIME
:SEL
YEAR
MONTH
DAY
HOUR
MINUTE
DAYLIGHT SAVING     YES   /    NO
CURRENT DATE             TIME
    JAN. 01. 2004     00  :  00  :  002004
JANUARY
01
00
00
:SET
+ -:ADJSET
ADVANCED OPTION
IR CONTROL
TILING
HEAT STATUS
POWER ON DELAY
DATE & TIME
SCHEDULE
ADVANCED OPTION RESET
:SELSET:NEXTEXIT:RETURNMENU:EXIT MENU
ADVANCED OPTION RESET
:RETURNMENU:EXIT MENU
NO
YES
:SELEXIT
ADVANCED OPTION
IR CONTROL
TILING
HEAT STATUS
POWER ON DELAY
DATE & TIME
SCHEDULE
ADVANCED OPTION RESET
:SELSET:NEXTEXIT:RETURNMENU:EXIT MENU:RETURNMENU:EXIT MENU
POWER ON DELAY
 3 SEC.
+ -: ADJEXIT
ADVANCED OPTION
IR CONTROL
TILING
HEAT STATUS
POWER ON DELAY
DATE & TIME
SCHEDULE
ADVANCED OPTION RESET
:SELSET:NEXTEXIT:RETURNMENU:EXIT MENUEXIT
:RETURN:SEL:SET
+ -:ADJSETEXIT
:RETURN:SEL:SET
+ -:ADJSET
SCHEDULE
TODAY   2005.     4.  15    FRI      15:11
                 ON       OFF        INPUT
     2         08:30    17:15     RGN1
     3
     4         EVERY DAY    MON    TUE 
     5         WED   THU   FRI   SAT
     6         SUN   EVERY WEEK
     71
ADVANCED OPTION
IR CONTROL
TILING
HEAT STATUS
POWER ON DELAY
DATE & TIME
SCHEDULE
ADVANCED OPTION RESET
:SELSET:NEXTEXIT:RETURNMENU:EXIT MENU
HEAT STATUSCOOLING   FAN1             ON 
COOLING   FAN2             ON
BRIGHTNESS                   NORMAL
TEMPERATURE
EXIT:RETURNMENU:EXIT MENUSENSOR 1              0.0 C   /  32.0 F
SENSOR 2              0.0 C   /  32.0 F
 
						

							1-29 
English-27
English
NOTE 1: IMAGE PERSISTENCEPlease be aware that LCD Technology may experience a phenomena known as Image Persistence. Image Persistence occurs when a
residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT monitors, LCD monitors’ image persistence is not
permanent, but constant images being displayed for a long period of time should be avoided.
To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an image was on the
monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image.
As with all personal display devices, MITSUBISHI ELECTRIC recommends displaying moving images and using a moving screen saver at
regular intervals whenever the screen is idle or turning off the monitor when not in use.
Please set “SCREEN SAVER”, “DATE &TIME” and “SCHEDULE” functions to further reduce the risk of Image persistence.
For long life use of Public Display
< Image Sticking of LCD Panel >
When LCD panel is operated continuously for long hours, a trace of electric charge remains near the electrode inside LCD, and residual or
"ghost" image of previous image may be observed. (Image Persistence)
Image Persistence is not permanent, but when fixed image is displayed for long period, ionic impurities inside LCD are accumulated along
the displayed image, and it is observed permanently. (Image Sticking)
< Recommendations >
For preventing the fast transition to Image Sticking, and for longer life usage of LCD, following are recommended.
1. Fixed image should not be displayed for long period, and changed to another images with short cycle.
2. When no use, please turn off the monitor by remote control, or use Power Management Function of monitor or use Schedule Function of
monitor.
3. Reducing the environmental temperature is effective for long life use.
When Protection board (glass, acryl) is installed over the LCD surface, enclosed into the box / wall, or stack the monitor, please utilize the
temperature sensors inside monitor.
To reduce the environmental temperature, the monitor should be set Low Brightness or Cooling Fan "ON" by using Screen sever Function.
4. Please use "Screen Saver Mode" of monitor.
NOTE 2: HOW TO SETUP SCHEDULEUsing the “SCHEDULE” function allows you to set up to seven different scheduled time intervals when the LCD Monitor will be activated.
You can select the time the monitor turns on and turns off, the day of week the monitor is activated, and which input source the monitor will
use for each scheduled activation period. A check mark in the box next to the number of the schedule indicates that the selected schedule
is in effect.
To select which schedule to set, use the up/down arrows to move the number (1 to 7) of the schedule.
Use the (+) and (-) buttons to move the cursor horizontally within the particular schedule. Use the (
) and () buttons to increase time
and select input port. The “SET” button is used to make a selection.
If you create a schedule but do not want to use a power on time, select “--” in the “ON” time slot.
If you do not want to use a power off time select “--” in the OFF time slot.
If there is no input selected (“--” showing in the input spot) the input from the previous schedule will be used.
The selection of EVERY DAY within a schedule takes priority over other schedules that are set up to operate weekly.
When schedules are overlapping, scheduled Power ON time has priority over scheduled Power OFF time.
If there are two schedules programmed for the same time, then the highest numbered schedule has priority.
When the “OFF TIMER” (see page 24) is set, the “SCHEDULE” function is disabled.
 
						

							1-30 
English-28
Controlling the LCD monitor via RS-232C Remote Control
This LCD monitor can be controlled by connecting a personal computer with a RS-232C terminal.
Functions that can be controlled by a personal computer are:
• Power ON or OFF
• Switching between input signals
Connection
LCD Monitor + PC
NOTE:If your PC (IBM or IBM compatible) is equipped only with a 25-pin serial port connector, a 25-pin serial port adapter
is required. Contact your dealer for details.
* RS-232 OUT terminal can connect to MDT321S only. Do not connect to other equipment.
1) Interface
This LCD monitor uses RXD, TXD and GND lines for RS-232C control.
2) Control command diagram
The command is structured by the address code, function code, data code and end code. The length of the command is
different for each function.
[Address code] 30h 30h (ASCII code, '0' '0'), fixed.
[Function code] A code of each fixed control move.
[Data code] A code of each fixed control data (number) and not always indicated.
[End code] 0Dh (In ASCII code, '
') fixed.
PROTOCOL RS-232C
BAUD RATE 9600 [bps]
DATA LENGTH 8 [bits]
PARITY BIT NONE
STOP BIT 1 [bits]
FLOW CONTROL NONE
Address code Function code Data code End code
HEX 30h 30h Function Data 0Dh
ASCII '0' '0' Function Data
RS-232C Cable