Mitsubishi Lvp X30u Projector User Manual

							E – 29
ENGLISH
⇔ ⇔
Using the Power Saving Function
When there is no signal input for a period of 5 min. or
more, the power is automatically turned off and standby
status is activated.
1With the FLIP COVER of the remote con-
trol open, press the MENU button to dis-
play the Advanced menu, then use the
cursor $ / % buttons to select “SETUP”.
2When SETUP menu is displayed, use the
cursor { / } keys to select “AU TO
POWER OFF”.
3Use the cursor $ / % keys to set Power
Saving to ON or OFF.
To close the menu
Press the CANCEL button.
Auto Source Settings
Automatically Searching The Input Signal
1With the FLIP COVER of the remote con-
trol open, press the MENU button to dis-
play the Advanced menu, then use the
cursor $ / % keys to select “SETUP”.
2Use the cursor { / } keys to select
“AUTO SOURCE”, then use the cursor $
/ % keys to set ON or OFF.
ON: All input signals are searched.
OFF: Remote control VIDEO button:
Video and S-video are searched.
Remote control RGB button:
RGB and YCbCr signals are searched.
Main unit SOURCE button:
All input signals are searched individually.
Selecting a Projection Type
If the projection type is not correctly set in accordance with the
installation conditions, images may be projected reversed, verti-
cally, or horizontally.
1With the FLIP COVER of the remote con-
trol open, press the MENU button to dis-
play the Advanced menu, then use the
cursor $ / % keys to select “SETUP”.
2When SETUP menu is displayed, use the
cursor { / } keys to select “PROJEC-
TION”, then press the ENTER button.
3Use the cursor { / } keys to select a
projection type in accordance with the
set conditions.
The setting items will change as shown below
each time a key is pressed.
      Normal⇔
Reversed vertically+horizontally
Reversed vertically⇔Reversed horizontally 
						

							E – 30
Selecting a Menu Language
Any one of eight different languages can be selected for
menu displays.
1With the FLIP COVER of the remote con-
trol open, press the MENU button to dis-
play the Advanced menu, then use the
cursor $ / % keys to select “OPTION”.
2When OPTION menu is displayed, use the
cursor { / } keys to select “LAN-
GUAGE”, then press the ENTER button.
3Use the cursor { / } keys to select one
of the following languages.

English

German

French

Italian

Swedish

Spanish

Chinese

Japanese
Setting the Menu Display Position
The menu display position can be set with this function.
1With the FLIP COVER of the remote con-
trol open, press the MENU button to dis-
play the Advanced menu, then use the
cursor $ / % keys to select “OPTION”.
2When OPTION menu is displayed, use the
cursor { / } keys to select “MENU POSI-
TION” and then press the ENTER button.
3Use the cursor { / }, $ / % keys to set
the display position.
Setting the Menu
To close the menu
Press the CANCEL button.
Menu Viewing Settings
The menu viewing method can be set with this function.
1With the FLIP COVER of the remote con-
trol open, press the MENU button to dis-
play the Advanced menu, then use the
cursor $ / % keys to select “OPTION”.
2When OPTION menu is displayed, use the
cursor { / } keys to select “MENU TYPE”.
3Use the cursor $ / % keys to select
“TRANSLUCENT” or “OPAQUE”.
Other Menu Settings
The time that the menu is displayed on the screen can be
set with this function.
1With the FLIP COVER of the remote con-
trol open, press the MENU button to dis-
play the Advanced menu, then use the
cursor $ / % keys to select “OPTION”.
2When OPTION menu is displayed, use the
cursor { / } keys to select “DISPLAY
TIME”.
3Use the cursor $ / % keys to set a value
from 5 sec. to 30 sec.
On-screen Display
This function is set to ON at the factory. When set to ON,
input will be projected onto the screen when the input is
switched with the remote control button. Also, the Input
menu will be displayed when the power is turned on to
indicate the selected input. In addition, status is displayed
on the menu bar when FREEZE, MUTE, ZOOM, KEY-
STONE or VOLUME is set.
1With the FLIP COVER of the remote con-
trol open, press the MENU button to dis-
play the Advanced menu, then use the
cursor $ / % keys to select “OPTION”.
2When OPTION menu is displayed, use the
cursor { / } keys to select “ON SCREEN”.
3Use the cursor $ / % keys to set ON or
OFF. 
						

							E – 31
ENGLISH
Symptom
The power will not turn on.
No image
Distorted images
Blurred images
Images are offset vertically or
horizontally and are not
correctly displayed
The remote control does not
work
The wireless mouse does not
work
The STATUS indicator blinks
Flickering text or offset colors
with RGB inputProcedure
• Is the power plug connected to the power outlet?
• Is the lamp cover correctly installed?
• Is the internal temperature too high? A protective feature prevents the
power turning on when the internal temperature is too high.
• Has the lamp usage time exceeded 1100 hours? The power will not turn
on when 1100 hours have elapsed.
• Any high-tension noise to the power line with extremely high pulse can
stop the projector. If it happens, unplug the power cord from the outlet
once and then plug it again.
• Has the connected input been selected?
• Is the cable correctly connected to the input jack?
• Are the brightness and contrast set to minimum?
• Is the sliding lens cap closed?
• Is the lamp blown?
• Has the lamp usage time exceeded 1100 hours?
• If a notebook type computer is being used, was the computer power turned
on after the projector was connected? Is the computer set to disable out-
put to the external RGB jack?
In many cases, when a notebook type computer is connected to the pro-
jector, a signal will not be output to the RGB OUT jack unless the com-
puter power is turned on.
• Does the STATUS indicator blink?
• Is installation correct?
• Was the Keystone adjustment performed correctly?
• Is the lens properly focused?
• Are the screen and projector positioned at the correct angle?
• Does the projection distance place the screen outside the focus range?
• Is there condensation, dirt, etc., on the lens?
Condensation on the internal optical system is possible when the projec-
tor has been stored in a cool place and then is used in a warm place. In
such cases, wait several minutes for the condensation to evaporate.
• Correctly adjust the horizontal and vertical position of the screen.
• Is the clock frequency correctly adjusted?
• Are the resolution and frequency correct for the input signal? Check the
resolution of the personal computer.
• Does the send indicator (LED) light? If it does not light, the batteries are
exhausted. In such cases, replace with fresh batteries.
• Is there any obstacle between the remote control and the photoreceptor
of the main unit?
• Is the remote control being used outside its effective range?
• Is there a fluorescent light or other strong light source close to the photo-
receptor?
• Is the MOUSE jack of the main unit and the personal computer correctly
connected?
• Was the personal computer started after being connected to the MOUSE
jack of the main unit?
• Check the STATUS indicator list.
• Manually adjust the clock frequency and phase.
• Press the AUTO button.
Please check the following before requesting repairs.
Troubleshooting
Others
Reference page
14
33
32
25, 32, 33
16, 18
10, 11, 12
22
14
33
25, 32, 33
12, 13
32
14
18, 28
15
14
9
—
24
24
23
5, 8
5
5
—
17
17
32
24 
						

							E – 32
Condition
OFF
On Continually
Flashing Very Rapidly (On and off
in a cycle of 1 sec.)
Flashing Rapidly
(On and off in a cycle of 4 sec.)
Flashing Slowly (On and off in a
cycle of 8 sec.)
Flashing Very Slowly (On and off in
a cycle of 12 sec.)Status
Normal
The lamp usage has exceeded 1000 hours of operation and should be replaced.
•The lamp cover is not correctly attached. Replace it correctly.
•The temperature protector has been triggered. If the room temperature is high,
move the unit to a cool location.  If the temperature within the unit is high, check the
cooling fan ventilation slots and the ventilation slots on the bottom of the unit.  If
any of the slots are blocked, remove whatever is blocking them.
•The temperature protector has been triggered. If you try to turn on the unit immedi-
ately after turning off, sometimes the power does not come on. If this happens, wait
at least one minute, then turn on the unit again.
•The lamp lighting voltage error detection protector has been triggered. Wait at
least one minute before turning on the unit again. If this does not solve the problem,
please contact your dealer.
 The cooling fan has stopped. Contact your dealer for service.
The lamp is not turned on.
•The unit was turned on immediately after being turned off. Turn off the unit, wait at
least one minute, then turn on the unit again.
•The lamp is dead. Replace the lamp cartridge. (See page 33.)
Status Light Messages
STATUS indicator
When the STATUS indicator lights or flashes
POWER STATUSPOWERSOURCEAUTO 
						

							E – 33
ENGLISH
The rated lamp life is about 1,000 hours. The rated lamp life is the average
life of the lamps produced and tested (under the test conditions of our
company) for a  long term, however, it may become shorter depending on
the conditions of usage.
After the lamp has been operating for 1000 hours or longer, the STATUS
indicator on the control panel will light and the “LAMP USAGE” icon
which shows hours of total lamp usage will be displayed on the screen.
When this happens, turn off the unit and replace the lamp cartridge with a
new one. The unit will not turn on after 1100 hours. (It will go off if it is in
use.)
CAUTION
• DO NOT TOUCH THE LAMP immediately after it has been
used. It will be extremely hot. Allow at least one hour for the
lamp to cool before handling.
• DO NOT LOOSEN ANY SCREWS except for those men-
tioned in the instructions below. There is danger of electric
shock.
Lamp cartridge replacement procedure
1 Disconnect the power cable.
Wait at least one hour for the lamp to cool.
2 Turn the unit upside down carefully.
3 Loosen the lamp cover securing screw.
4 Remove the lamp cover.
CAUTION: Do not use a lamp cartridge other than the
Mitsubishi replacement lamp cartridge. Order this from your
dealer using the unit model number (see “Notes” below).
5 Loosen the three lamp cartridge securing screws.
(This unit has a safety switch.)
6 Hold the handle then pull the lamp cartridge upward to remove
it.
7 Install the new lamp cartridge.
8 Secure the lamp cartridge with the three screws.
9 Replace the lamp cover and secure it with the securing screw.
10 Return the unit to the normal position, connect the power cable,
and turn on the unit.
11 Reset “LAMP USAGE.” (See page 25).
Replacing the lamp cartridge
Step 3
Step 4
Step 5
Step 6
Step 7
Step 8
Step 9
Notes
• When the lamp usage time reaches 1100 hours, it becomes impossible
to switch on the power and menus are not displayed. In such a case,
see “If the unit doesn’t go on because lamp usage exceeds 1100
hours” on page 25.
• Obtain a replacement lamp cartridge at the store where the unit was
purchased. Please specify the following information when ordering a
replacement lamp cartridge:
– Model name : VLT-X30LP
Lamp cartridge
Lamp Cover 
						

							E – 34
Optical
DMDTMSingle Chip Digital Micro Device (DMDTM)
1024 × 768 dots
Lens Manual focus fixed lens
F=3.0 f=23 mm
Lamp High Performance Compact Lamp
Image Size 914 to 5080 mm (36 to 200 in.) diagonal
Projection Distance 1.2 to 6.8m (3.9 to 22.3 ft.)
Light Output 800 ANSI lumens (normally white)
Contrast Ratio 800 : 1
Electrical
Inputs Video (NTSC / PAL / PAL_M / PAL_N / PAL60 / SECAM / NTSC4.43)
RGB (H:15 to 91 kHz, V: 50 to 85 Hz)
Color Reproduction Full color, 16.7 million colors simultaneously.
Resolution SXGA (Compression), XGA(True), SVGA/VGA (Expansion/True)
Power Requirement 100 to 120/220 to 240 V AC, 50/60 Hz
Power Consumption 180 watts
Mechanical
Dimensions Excluding Stand 23.0 cm (W) × 4.8 cm (H) × 17.7 cm (D) / 9.0 in.(W) × 1.9 in.(H) × 7.0 in.(D)
Net Weight 1.4 kg / 3.1 lbs
Operational Temperatures Data projector: 5° to 35°C (41° to 95°F), 30 to 85 % humidity
Remote control: 0° to 60°C (32° to 140°F)
Regulations UL Approved (UL 1950, CSA 950)
Meets FCC Class A requirements
Meets EMC Directive (EN55022, EN55024)
Meets Low Voltage Directive (EN60950)
Specifications
D-Sub Pin Assignments
  PC 15-Pin mini D-SubPin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal to be connected
Red
Green
Blue
GND
GND
Red GND
Green GND
Blue GND
No Connection
Digital GND
GND
SDA
Horizontal Sync
Ver tical Sync
SCL 
						

							E – 35
ENGLISH
Dimensions
OPEN
POWER STATUS
POWER
SOURCE
AUTO
230 mm/9.0″
177 mm/7.0″48 mm/
1.9″11 mm/
0.4″
27 mm/
1.1″ 
						

							Printed in Japan
Manufactured by Mitsubishi Electric Corporation
1 Zusho Baba, Nagaokakyo-City, Kyoto Japan