Mitsubishi Ldt521v Operation Guide

OPERATION GUIDE 
52
 

2E
This guide contains instructions regarding operation, settings, and similar details.
For instructions regarding connection and installation, refer to the included Operation Manual.
Manual Scope
-  Microsoft, Windows and Internet Explorer are registered trademarks of Microsoft Corporation.
-  HDMI, the HDMI Logo and High-Defi nition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing 
LLC.
-  Adobe, Acrobat, and Reader are either registered trademarks or trademarks of Adobe...

3E
Basic Operation
1 
2 
3 
4 
5 
6 
7 
8
1. INPUT (Input mode selection)
The menu is displayed. Press 
 or  to select the input 
mode, and press 
 to enter.
*  You can select the input terminal by pressing the input 
switch of the monitor.
Input mode Video Audio
PC1 DVI-D
*1PC1 input terminal
PC audio input 
terminal PC2 HDMI
*2PC2 input terminal
PC3 D-SUB PC3 input terminal
PC4 RGB
*3PC4 input terminals
AV1 DVI-D
*1AV1 input terminal
AV audio input 
terminals AV2 HDMI
*2AV2 input terminal
AV3...

E4
Basic Operation
„Switching the screen size
Even when the screen size is changed, the display may remain the same depending on the input signal.
WIDEPC input Displays image so it fi lls the entire screen.
AV input An image with a 4:3 aspect ratio is stretched to fi ll the entire 
screen.
ZOOM 1
PC input An image with a 4:3 aspect ratio is enlarged to fi ll the entire screen 
without changing the aspect ratio. The edges of the image may be 
cut off.
AV input
ZOOM 2
PC input Use this size if ZOOM 1 cuts off...

5E
Menu Items
Displaying the menu screen
Video and audio adjustment and settings of various functions 
are enabled. This section describes how to use the menu 
items. See pages 6 to 8 for details of each menu items.
„Example of operation
(Adjusting CONTRAST in the PICTURE menu)
1. Press MENU to display the menu screen.
1920x1080 
V: 60 Hz    H: 66.3 kHz
AUTO 
CLOCK 
PHASE 
H-POS 
V-POS 
H-SIZE 
V-SIZE 
H-RESOLUTION 
V-RESOLUTION 
RESET 
SCREEN 
PICTURE 
AUDIO 
SETUP 
OPTION 
ENLARGE 
PIP/PbyP 
600
31...

E6
Menu item details
The menu will differ depending on the input mode.
„SCREEN
AUTO (PC3/PC4)
The CLOCK, PHASE, H-POS, and V-POS are automatically 
adjusted.
Pressing  
 
performs adjustment.
Use this automatic adjustment when you use the PC3 input 
terminal or PC4 input terminals to display a PC screen for 
the fi  rst time or when you change the setting of the PC. (See 
page 10.)
CLOCK (PC3/PC4)
Adjusts frequency for sampling clock for applicable video.
Adjust when there is  fl ickering in the form of...

E7
SCREEN MOTION
Residual images are reduced by moving the screen.
PATTERN 1 ....  The whole screen moves vertically and horizontally.
PATTERN 2 ....  A black screen spreads from the bottom of  the screen and then shrinks to the bottom of 
the screen. If the monitor is installed in the 
vertical orientation, a black screen spreads 
from the left end of the screen and then 
shrinks to the left end of the screen.
PATTERN 3 .... 
A black bar moves from the left end to the right 
end of the screen. If the...

E8
Menu Items
TIPS
•  When WHITE BALANCE is set to THRU, BLACK LEVEL, CONTRAST, TINT, COLORS and GAMMA cannot be set.
•  If COLOR MODE is set to sRGB or VIVID, the following  items cannot be set.
WHITE BALANCE, PRESET, R-/G-/B-CONTRAST, COPY 
TO USER, and GAMMA
„Dual screen display
You can display the screens of the PC input signal and AV 
input signal simultaneously.
Set this function with “PIP MODES” in the PIP/PbyP menu.
PIPMain screen 
Sub 
screenA sub screen is displayed 
inside a main screen.
PbyP...

E9
Menu Items
„ Enlarge
•  You can align several monitors and integrate them into a 
single large screen to display.
• Up to  fi ve monitors can be aligned in both the horizontal 
and vertical directions.
•  Each monitor displays enlarged views of separated images.
(Example)
Horizontal direction: 2 monitors
Vertical direction: 2 monitors
Horizontal direction: 3 monitors
Vertical direction: 2 monitors
Setting procedure
In the ENLARGE menu, set ENLARGE H/V and 
ENLARGE-POS H/V. (See page 8.)
1.  Set the...

E10
Menu Items
(5) INPUT
Specifi es the input mode at power-on. When not specifying, 
the screen at the previous power-off appears.
Input modes displayed on “PC1/AV1” depend on DVI 
SELECT settings.
Input modes displayed on “PC2/AV2” depend on HDMI 
SELECT settings.
Input modes displayed on “PC4/AV3” depend on BNC 
SELECT settings.
Caution
•  Do not switch off the main power after setting the 
SCHEDULE.
•  Specify the correct date and time. (See page 7.)
SCHEDULE does not function unless the date and time...