Mitsubishi Hc910 Projector User Manual

EN-11
ENGLISHScreen size and projection distance
Refer to the following table to determine the screen size. 
B
 A
Hd
 40 102 20 50 35 89 55 1.4 67  1.7 6.4 16.2
 60 152 29  75  52 133 84  2.1 102  2.6 9.6 24.3
 80 203 39 100 70 177 113 2.9 137  3.5 12.7 32.4
 100 254 49 125 87 221 142 3.6 171  4.4 15.9 40.5
 150 381  74  187 131 332 213  5.4  258  6.6 23.9 60.7
 200 508  98  249 174 443 285  7.2  345  8.8 31.9 80.9
 250 635 123 311 218 553 357  9.1  -  -  39.8 101.1
 275 699 135 342 240 609 393 10.0  -...

EN-12
Viewing video images
A. Connecting the projector to video equipment
Preparation:
•  Make sure that the power of the projector and that of the video equipment are turned off. 
Basic home theater system connection
VIDEO IN
COMPONENT VIDEO IN
CB/PB
Y
CR/PR
S-VIDEO IN
Video player
DVD player
Set-top box or digital tuner 

EN-13
ENGLISH
COMPONENT VIDEO IN
PB/CBY PR/CR 
PB/CB
Y
PR/CR
S-VIDEO IN
VIDEO IN
12
S-VIDEO IN
COMPONENT VIDEO IN
VIDEO IN
COMPONENT VIDEO IN
12VIDEO IN S-VIDEO IN
Connecting to a video player, etc.
1.  Connect one end of the optional video cable to the VIDEO 
IN terminal of the projector. 
2.  Connect the other end of the video cable to the video 
output terminal of the video equipment. 
•  Also read the instruction manual of the equipment to be connected. 
•  Contact your dealer for details of...

EN-14
Viewing video images (continued)
Connecting to video equipment having a DVI-D terminal
You can project high-quality images by connecting the DVI-D terminal of this projector to video equipment having a 
DVI-D output terminal. In addition, this projector supports HDCP and is able to receive encrypted digital video data 
that are output from DVD players. 
•  For connection to the DVI-D IN terminal, use a commercially available DVI cable. 
•  Select DVI as the input source. 
•  Only RGB signals are...

EN-15
ENGLISHC. Projecting images
Preparation:
•  Remove the lens cap.
•  Turn on the power of the connected video equipment. 
1. Confi rm the POWER indicator lights up red. 
•  If the projector was turned off before the lamp was cooled down suffi ciently last time, the fan may start rotating 
and the POWER button may not work after the power cord is plugged. (The STATUS indicator blinks green.) 
After the fan stops rotating, press the POWER button to turn back on the POWER indicator. 
2.  Press the POWER...

EN-16
Viewing video images (continued)
To stop projecting:
8.  Press the POWER button on the projector or the OFF () button on the remote control. 
• A confi rmation message is displayed.
•  To cancel the procedure, leave the projector for a while or press the MENU button. 
9.  Press the POWER button on the projector or the OFF (
) button on the remote control again. 
•  The lamp goes out and the projector goes into a standby mode. In this standby mode, the POWER indicator 
blinks red. 
10. Wait about one...

EN-17
ENGLISH
Setting the aspect ratio
You can change the aspect ratio of the input video signal (or the ratio of width to height of the image). Change the 
setting according to the type of the input video signal. 
How to change the settings:
With the remote control:
1.  Press the ASPECT button. 
•  Every time the ASPECT button is pressed, the aspect mode changes from AUTO to 4:3, to 16:9, to EXPAND, to 
REAL, and back to AUTO. 
•  When the keystone adjustment is applied, the REAL mode can not be...

EN-18
COMPONENT VIDEO IN
2 1
VIDEO IN S-VIDEO IN
COMPONENT VIDEO IN
2 1
S-VIDEO IN
VIDEO IN
Viewing computer images
A. Connecting the projector to a computer
Preparation: 
•  Make sure that the power of the projector and that of the computer are turned off. 
•  When connecting the projector to a desktop computer, disconnect the RGB cables that are connected to the 
monitor. 
For analog connection: 
1.  Connect one end of the supplied RGB cable to the 
COMPUTER IN/COMPONENT VIDEO IN terminal of the...

EN-19
ENGLISH
C. Projecting images
Preparation:
•  Remove the lens cap.
•  Turn on the power of the connected computer. 
1. Confi rm the POWER indicator lights up red. 
•  If the projector was turned off before the lamp was cooled down suffi ciently last time, the fan may start rotating 
and the POWER button may not work after the power cord is plugged. (The STATUS indicator blinks green.) 
After the fan stops rotating, press the power button to turn back on the POWER indicator. 
2.  Press the POWER button...

EN-20AUTO POSITION button 
When the image supplied from the computer is displaced, carry out the following procedure. 
1.  Display a bright image (such as a full-screen display of the Recycle Bin window). 
2.  When the screen saver has been enabled, disable it. 
3.  Press the AUTO POSITION button.  
    The projector automatically makes optimum positional settings for the input signal. 
•    If the image is not projected in the correct position even after you press the AUTO POSITION button several...