Mitsubishi Hc6800 Projector User Manual

EN-11
Setting up your projector (continued)
Screen size and projection distance (continued)
Screen width (SW)
Down sideUp side
50%
50%
Screen
Screen height (SH)
H1
H1
LRight side
Left side
W1 W1
When the aspect ratio of the screen is 4:3
When the aspect ratio of the screen is 4:3, the positional relation between the 
projected image and the screen is as shown on the right. Refer to the following 
table for installation.
When the aspect ratio of the image is 16:9
Screen size (4:3)Size of the projected...

EN-12
Adjusting the position of the projected image
To adjust the position of the projected image on the screen, use the LENS SHIFT button.Press the LENS SHIFT button.
1. 
The LENS SHIFT menu appears at the center of the screen.
•	
Press the 
2.  p, q, t or u button to move the image position.
When the 
•	 q button is pressed, the image moves down.
When the 
•	 p button is pressed, the image moves up.
When the 
•	 u button is pressed, the image moves to the right.
When the 
•	 t button is pressed, the...

EN-13
Front projection, ceiling mounting
For ceiling mounting, 
you need the ceiling 
mount kit designed 
for this projector. 
Ask a specialist for 
installation. For details, 
consult your dealer.The warranty on this projector does not cover any 
•	
damage caused by use of any non-recommended 
ceiling mount kit or installation of the ceiling mount 
kit in an improper location.
When using the projector mounted on the ceiling, 
•	
set IMAGE REVERSE in the INSTALLATION menu 
to MIRROR INVERT. See page 27....

EN-14
DVD player
A. Connecting the projector to video equipment
When the projector and the connected devices are located too close to each other, the projected image may be 
•	
affected by their interference.
See the owner’s guide of each device for details about its connections.
•	
Preparation:
Make sure that the power of the projector and that of the video equipment are turned off.
•	
Basic home theater system connection
Video player
Set-top box or digital tuner
Viewing video images 

EN-15
12
12
Connect one end of the optional video cable to the 
1. 
VIDEO IN terminal of the projector.
Connect the other end of the video cable to the video 
2. 
output terminal of the video equipment.
Also read the instruction manual of the equipment to be connected.
•	
Contact your dealer for details of connection.
•	
When a TV tuner or VCR is connected:
When you use this projector with a TV tuner or VCR connected, no image may appear or a messa\
ge of NO SIGNAL 
may appear on the screen when you...

EN-16
Connecting to video equipment having a HDMI terminal
You can project high-quality images by connecting the HDMI IN terminal of this projector to video equipment having 
a HDMI output terminal. In addition, this projector supports HDCP and is able to receive encrypted digital video data 
that are output from DVD players.Select HDMI as the input source.
•	
HDCP (High-bandwidth Digital Content Protection), developed by Intel Corporation, is a method to encrypt digit\
al 
•	
video data for the purpose...

EN-17
B. Plugging in the power cord
In order to ensure the safety in case of trouble with the projector, use an electrical outlet having an earth leakage 
•	
breaker to supply the power to the projector. If you do not have such outlet, ask your dealer to install it. 
The power cords for use in the U.S. and Europe are included with this projector. Use the appropriate one for your 
•	
country.
This projector uses the power plug of three-pin grounding type. Do not take away the grounding pin from the 
•...

EN-18
Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red. 
1. 
If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating 
•	
and the POWER button may not work after the main power switch is turned ON. (The STATUS indicator blinks 
green.) After the fan stops rotating, press the POWER button to turn back on the POWER indicator. 
Turn on the power of the connected video equipment.
2. 
Press the...

EN-19
Press the POWER button on the projector or the OFF (
13. ) button on the remote control.
A confirmation message is displayed.
•	
To cancel the procedure, leave the projector for a while or press the MENU button.
•	
Press the POWER button on the projector or the OFF (
14. 
) button on the remote control again.
The lamp goes out and the projector goes into a standby mode. In this standby mode, the STATUS indicator 
•	
blinks green.
Wait about 2 minutes.
15. 
During this period of 2 minutes in the...

EN-20
Viewing video images (continued)
Setting the aspect ratio
You can change the aspect ratio of the input video signal (or the ratio \
of width to height of the image). Change the 
setting according to the type of the input video signal.
 : Signal size   : Image area
Setting
Original image size4:3 16:9 ZOOM1 ZOOM2 STRETCHANAMORPHIC1 ANAMORPHIC2
Aspect ratio 
changes 
depending on the 
input signal. Squeezed image is 
expanded to 16:9. CinemaScope image 
is enlarged and 
displayed together 
with...