Mitsubishi Hc3900 Projector User Manual

EN-1

Viewing video images (continued)
How to change the settings:
With the remote control:
Press the ASPECT button.Every time the ASPECT button is pressed, the aspect mode changes from AUTO to 4:, 16:9, to ZOOM1, to 
ZOOM, to STRETCH, to ANAMORPHIC1, to ANAMORPHIC, and back to AUTO.
Some modes are not available with certain signals.
With the FEATURE menu:
(See page 6 for menu setting.)
Display the FEATURE menu.
Select ASPECT by pressing the p or q button.
Select your desired...

EN-

Viewing computer images
A. Connecting the projector to a computer
Preparation:
Make sure that the power of the projector and that of the computer are turned off.
When connecting the projector to a desktop computer, disconnect the RGB cables that are connected to the 
monitor. 
Connect one end of the supplied RGB cable to the 
COMPUTER IN/COMPONENT VIDEO IN terminal of the 
projector.
Connect the other end of the RGB cable to the monitor port 
of the computer.
Additional devices, such as a...

EN-

Viewing computer images (continued)
C. Projecting images
Preparation:
Remove the lens cap.
Turn on the power of the connected computer. 
COMPUTER button
p, q, t, u buttons
ON ( I ) button
HC3900
POWER button
POWER indicator
STATUS indicator
HDMI / COMPUTER / t button
Confirm the POWER indicator lights-up red.
If the projector was turned off before the lamp had cooled down sufficiently, the fan may start rotating and the 
POWER button may not work after the power cord is plugged. (The...

EN-4
Viewing computer images (continued)
Adjust the image size by turning the zoom ring.
If necessary, adjust the focus and zoom again.
To stop projecting:
Press the POWER button on the projector or the OFF () button on the remote control.
A confirmation message is displayed.
To cancel the procedure, leave the projector for a while or press the MENU button.
Press the POWER button on the projector or the OFF () button on the remote control again.
The lamp goes out and the projector goes into a...

EN-25
Menu operation
Menus are not displayed when no signal is supplied to the projector.
AUTO, 0 - 10
BrilliantColorTM
IMAGE
GAMMA MODE
USER1    SPORTS, VIDEO, CINEMA
ALL, RED, GREEN, BLUE ±10(R) ±10(G) ±10(B)
±10(R) ±10(G) ±10(B)
±10(R) ±10(G) ±10(B)
COOL, MEDIUM, WARM±60
±60
±60
±60
±60
±60
16:9, CINEMA SCOPE (2.35:1) ±26
0 - 5 ±5
(for analog signal input)
AUTO, ENHANCED, NORMAL (for digital signal input)OFF
ON    
COLOR GAIN
RED, YELLOW, GREEN, CYAN, BLUE, MAGENTA±20
SATURATION ±20
POSITION RESET...

EN-26
Menu operation (continued)
1. IMAGE menu
How to set the menus:
The following describes how to set AUTO POWER OFF 
time as an example.Press the MENU button.
CONTRAST
IMAGE
0
BRIGHTNESS 0
0
COLOR
OK
MIDIUM
0
TINT
0SHARPNESS
COLOR TEM P.
ADVANCED MENU
opt.
AUTOGAMMA MODE
AV MEMORY 1
AV MENU SAVEAV MEMORY1
Press the t or u button to select a menu to use.
IMAGE
REVERSE
OFF
AUTO POWER 
ON
OFFAUTO POWER 
OFF
SCREEN SIZE
ON
INSTALLATION
ON
BACK COLOR
OFF
TEST PATTERNCROSS HATCHBLUE
SPLASH
SCREEN WXGA...

EN-7

Menu operation (continued)
. INSTALLATION menu
IMAGEREVERSE
OFF
OFF
BACK COLOR
OFF
opt.
STANDARDLAMP MODE
AV MEMORY 1
AUTO POWERONAUTO POWEROFF
INSTALLATION
TRIGGER OUTOFF
ONON
BLUE
SPLASHSCREEN
TEST PATTERNCROSS HATCH
KEYSTONE0
2. INSTALLATION menu
ITEMSETTINGFUNCTION
KEYSTONE±15Use to correct vertical keystone distortion.
LAMP MODESTANDARDSelect this option when you want to view images in a well-lit room.
LOWSelect to moderate the intensity of the lamp. The fan operating sound is...

EN-8

Menu operation (continued)
. FEATURE menu
FEATURE
AUTO
AUTO
AUTO
opt.
MENU POSITION
CINEMA MODE
VIDEO SIGNAL?
ASPECT
RESET ALL
EnglishLANGUAGEAË
OFF
AUTO
OK
DISPLAYINPUTPASSWORDFUNCTION1.
MENU DIMMER
AV MEMORY 1
SETUP
SCART INPUT
OFF
3. FEATURE menu
ITEMSETTINGFUNCTION
ASPECTAUTOSelect to change the aspect ratio automatically depending on the input signal.
4:  Select to project images with an aspect ratio of 4: .
16:9Select to project images with an aspect ratio of 16:9....

EN-9

Menu operation (continued)
4. SIGNAL menu 5. USER menu
R G BR G B
SIGNAL
HORIZ. POSITION0
VERT. POSITION0
TRACKING0COMPUTER INPUTAUTO
FINE SYNC.0
USER
opt.
OK
ONHOLD
100%OVER SCAN
AV MEMORY 1CLAMP POSITION
USER
1
CLAMP WIDTH1
LPFOFF
SHUTTER(U)0
SHUTTER(L)0
VERT. SYNCAUTO?
SHUTTER(LS)0
SHUTTER(RS)0
4. SIGNAL menu
ITEMSETTINGFUNCTION
HORIZ. POSITION0 - 999Use to adjust the horizontal position of the projected image.
VERT. POSITION0 - 999Use to adjust the vertical position of the projected...

EN-0

Menu operation (continued)
6. INFORMATION menu
INFORMATION
opt.
LAMP TIME(LOW)
INPUT
RESOLUTION
VERTICALFREQUENCY
HORIZONTALFREQUENCY
SYNC. TYPE5wire
60.02 KHz
75.04 Hz
1024X768
COMPUTER
0 H
R GH VB
6. INFORMATION menu
ITEMDESCRIPTION
LAMP TIME(LOW)This item shows a lamp operating time (hour) calculated based on that LAMP MODE 
is LOW.
When the LAMP MODE is STANDARD, this item shows a longer lamp operating 
time than the actual time. (See page 6 for the interval of lamp replacement. )...