Mitsubishi Hc100 Projector User Manual

EN-11
ENGLISH
C
B
DD
A
40 102 32 81 24 61 32 81 18 46 3.0 8 50 1.3 61 1.5 8.8 22.4
60 152 48 122 36 91 48 122 27 69 4.5 11 76 1.9 92 2.3 13.2 33.6
70 178 56 142 42 107 56 142 32 80 5.3 13 89 2.3 108 2.7 15.4 39.280 203 64 163 48 122 64 163 36 91 6.0 15 102 2.6 123 3.1 17.6 44.890 229 72 183 54 137 72 183 41 103 6.8 17 115 2.9 139 3.5 19.8 50.4
100 254 80 203 60 152 80 203 45 114 7.5 19 128 3.2 155 3.9 22.0 56.0110 279 88 224 66 168 88 224 50 126 8.3 21 141 3.6 170 4.3 24.2 61.5120 305 96 244 72 183 96...

EN-12
Viewing video images
A. Connecting the projector to video equipment
Preparations:
•Make sure that the power of the projector and that of the video equipment are turned off.
Basic home theater system connection
COMPONENT VIDEO IN
CB/PB
Y
CR/PR
Video player
DVD player
Set-top box or digital tuner 

EN-13
ENGLISH
COMPONENT VIDEO IN
PB/CBY PR/CR 
PB/CB
Y
PR/CR
12
COMPONENT VIDEO IN
34
COMPONENT VIDEO IN
13
4
2
Connecting to a Video player, etc.
1. Connect one end (yellow) of the supplied audio/video
cable to the VIDEO terminal of the projector.
2. Connect one end (white and red) of the supplied audio/
video cable to the audio input terminals (L/MONO, R) of
the projector.
3. Connect the other end (yellow) of the audio/video cable to
the video output terminal of the video equipment.
4. Connect the...

EN-14
Viewing video images (continued)
Connecting to video equipment having a DVI-D terminal
You can project high-quality images by connecting the DVI-D terminal of this projector to video equipment
having a DVI-D output terminal. In addition, this projector supports HDCP and is able to receive encrypted
digital video data that are output from DVD players.
•For connection to the DVI-D terminal, use a commercially available DVI cable.
•Select DVI as the input source.
•Only RGB signals are supported....

EN-15
ENGLISH
C. Projecting images
Preparation:
•Remove the lens cap.
•Turn on the power of the connected video equipment.
1. Confirm the POWER indicator lights up red.
•If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start
rotating and the POWER button may not work after the power cord is plugged. (The STATUS indicator
blinks green.) After the fan stops rotating, press the power button to turn back on the POWER indicator.
2. Press the POWER button on...

EN-16
Viewing video images (continued)
To stop projecting:
8. Press the POWER button on the projector or the OFF () button on the remote control.
•A confirmation message is displayed.
•To cancel the procedure, leave the projector for a while or press the MENU button.
9. Press the POWER button on the projector or the OFF (
) button on the remote control again.
•The lamp goes out and the projector goes into a standby mode. In this standby mode, the POWER indicator
blinks red.
10.Wait about one minute for...

EN-17
ENGLISH
Setting the aspect ratio
You can change the aspect ratio of the input video signal (or the ratio of width to height of the image). Change the
setting according to the type of the input video signal.
How to change the settings:
With the remote control:
1. Press the ASPECT button.
•Every time the ASPECT button is pressed, the aspect mode changes from AUTO to 4:3, to 16:9, to EX-
PAND, and back to AUTO.
With the FEATURE menu:
(See Page 21 for menu setting.)
1. Display the FEATURE menu.
2....

EN-18
COMPONENT VIDEO IN
2 1
COMPONENT VIDEO IN
2 1
Viewing computer images
A. Connecting the projector to a computer
Preparation:
•Make sure that the power of the projector and that of the computer are turned off.
•When connecting the projector to a desktop computer, disconnect the RGB cables that are  connected to the
monitor.
For analog connection:
1. Connect one end of the supplied RGB cable to the COM-
PUTER IN/COMPONENT VIDEO IN terminal of the
projector.
2. Connect the other end of the RGB cable...

EN-19
ENGLISH
C. Projecting images
Preparation:
•Remove the lens cap.
•Turn on the power of the connected computer.
1. Confirm the POWER indicator lights up red.
•If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start
rotating and the POWER button may not work after the power cord is plugged. (The STATUS indicator
blinks green.) After the fan stops rotating, press the power button to turn back on the POWER indicator.
2. Press the POWER button on the...

EN-20
AUTO POSITION button
When the image supplied from the computer is displaced, carry out the following procedure.
1. Display a bright image (such as a full-screen display of the Recycle Bin window).
2. When the screen saver has been enabled, disable it.
3. Press the AUTO POSITION button.
The projector automatically makes optimum positional settings for the input signal.
•If the image is not projected in the correct position even after you press the AUTO POSITION button
several times, change the...