Mitsubishi Fl7000u Projector User Manual

							EN-41
Maintenance
Warning:
•  Never use fl ammable air duster or other materials when cleaning the air-fi lter. Flammable substances may ignite 
causing fi re or backdown when the lamp is illuminated.
•  Do not use fl ammable solvents (benzene, thinner, etc.) and fl ammable aerosols when cleaning the projector body 
and lens. Flammable substances may ignite causing fi re or breakdown while the lamp is illuminating.
Caution:
Be sure to turn off the lamp and unplug the power cord from the wall outlet before you perform any maintenance on 
the projector. 
Cleaning of the air-fi lter
Clean the air-fi lter frequently (about once a month). If the fi lter or 
ventilation grilles become clogged with dirt or dust, the tempera-
ture inside the projector may rise and cause troubles, such as 
damage to the inside parts and shortening the life of the panels.
•  When the temperature inside the projector rises, the STATUS 
indicator will blink orange and the lamp will be turned off. 
1.  To remove the fi lter cover, slide the cover in the direction of the 
arrow.
2. Remove the air-fi lter from the fi lter cover.
3.  Wash the air-fi lter or change it with a new fi lter.
•  Use water or diluted mild detergent to clean the fi lter. Rinse 
the fi lter thoroughly and let it dry completely. 
4. Attach the air-fi lter to the fi lter cover.
5. Attach the fi lter cover to the projector.
•  Make sure that the air-fi lter is attached correctly without 
displacement.
Important:
•  If the fi lter is damaged or becomes extremely dirty, change it 
with a new fi lter. Contact your dealer for a new fi lter.
•  Use the dedicated fi lter only.
•  The power will not turn on if the fi lter cover is improperly 
installed.
Caution:
Be sure to use the projector with an air-fi lter. If not, dust may get inside the projector causing fi re and failure.
Cleaning of the projector and the ventilation slots
Use a soft cloth to clean the projector and the ventilation grilles. When the grilles become dirty, wipe them with a soft 
cloth dampened with diluted mild detergent, and then wipe them with a dry cloth.
•  Clean the inside of the terminal cover frequently as dust is apt to be collected. 
To protect the surface of the projector from fading or deteriorating:
•  Do not spray insecticide on or inside the projector.
•  Do not use benzine or thinner to clean it.
•  Do not let rubber or plastic materials contact with projector.
Cleaning of the lens
Use a standard lens-cleaning brush or a piece of lens tissue dampened with lens cleaning fl uid. The lens surface is 
fragile. Use only recommended, nonabrasive lens-cleaning materials. Do not touch the lens with your fi ngers. Filter cover
Air-fi lter
Filter cover 
						

							EN-42
Troubleshooting
Before asking for repair of the projector, check the following. If the symptom persists, stop using the projector, be 
sure to unplug the power plug, and then contact your dealer. 
No image appears on the screen. 
Problem Solution
Power can not be 
turned on.•  Check whether the indicators are on or off and how they are lightning.
 
•  If any objects are blocking the air inlet or outlet grille, remove them.
•  Don't expose the air outlet grilles to hot air emitted f
•  Check wheather the filter is clogged with dirt and dust.
Clean the filter, if clogged. (See page 41.)rom a heating appliance.
POWER
Off
Steady red
Blinking 
red / green
STATUS
Off
Off
Blinking 
orange
Blinking 
green
Steady red
Off
Steady
or
Blinking
  Solution
•  Connect the power cord to the projector. 
• Plug the power cord into a wall outlet. 
•  If any objects are blocking the air inlet or outlet grille, remove them and carry 
out the following.
1.  Turn off the main power swich.
2.  Make sure that the projector has cooled off. 
3.  Turn on the main power swich.
4.  Press the POWER button.
•  After the STATUS indicator stops blinking, press the POWER button.• If the main power switch is turned off while the fan is rotating, the lamp may not turn on about 1 minute  
when the main power switch is turned on next time.
•  The lamp can't turn on again for 1 minute after it goes out. 
•  Press the POWER button several times.
•  Replace the lamp. (The lamp is at the end of its life.)
•
•Attach the lamp cover on the bottom.
Attach the filter cover on the bottom.
•  Unplug the power cord from the wall outlet and contact your dealer.
• Turn on the main power swich. 
No image appears on 
the screen.•  Cancel the AV mute by pressing the AV MUTE button.
•  Check that the lens cap is removed. 
•  It may take about 1 minute for the lamp to light up. 
•  The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and 
then try again. 
•  If the projector was turned off before the lamp was cooled down suffi ciently last time, 
the fan may start rotating and the POWER button may not work after the main power 
switch is turned on. After the fan stops rotating, press the POWER button to turn back 
on the POWER indicator.
•  Set SCART INPUT in the FEATURE menu to OFF. (See page 25.)
•  Check that the intake vent is clean. 
•  Check that the lamp cover and the fi lter cover are closed. (See pages 39 and 41.)
•  Check that the cables connected to the external devices are not broken. 
•  When an extension cable is being used, replace it with the supplied cable for check. 
When images are displayed correctly, add an RGB signal amplifi er to the extension 
cable. 
Power turns off.  •  This problem may occur when the intake vent and/or exhaust vents are blocked. (In 
such a case, the STATUS indicator brinks orange.)
J  Remove the objects blocking the intake vent and/or exhaust vents and then carry 
out the following procedure. 
1.  Wait for the intake fan and/or exhaust fan to stop. (Wait until the STATUS indicator 
goes out.) 
2.  Turn off the main power switch. 
3.  Wait about 10 minutes.
4.  Turn on the main power switch.
5.  Press the POWER button. 
•  When the STATUS indicator is steady red, it is indicating that the lamp should be 
replaced. Replace the lamp in this case. 
•  Check that AUTO POWER OFF has been set to OFF. 
•  If the lamp has deteriorated, it may go out after a while it illuminates. 
The screen for entering 
the password appears.•  PASSWORD FUNCTION in the FEATURE menu has been set to DISPLAY INPUT 
 to 
enable the password lock. 
J Enter the password or contact the person in charge of management of the 
projector. (See page 33.) 
						

							EN-43
Troubleshooting (continued)
No image appears on the screen. (continued) 
Problem Solution
“NO SIGNAL” is 
displayed.•  Turn on the power of the connected device, or check whether there is something 
wrong with the connected device.
•  Check whether the external device output signals. (Check this especially when the 
external device is a notebook computer.) 
•  Check that the cable connected to the external device isn’t defective. 
•  Check that the projector is connected to the external device using the correct 
terminals. 
•  Check that the connected device is correctly selected as the input source. 
•  When an extension cord is being used, replace it with the supplied cable and check 
whether images are projected correctly. If images are projected correctly, use an RGB 
signal amplifi er along with the extension cord. 
Images are not displayed correctly. 
Problem Solution
Projected images are 
shaking.
Projected images are 
displaced. •  Check that the cable connected to the external device isn’t intermittent. 
•  Connect the cable’s plug with the external device’s connector fi rmly.
•  Project an image containing many characters such as a help menu and press the 
AUTO POSITION button.
•  Some computers output out-of-spec signals on rare occasion. Adjust the SIGNAL 
menu. (See pages 30 and 31.)
Projected images are 
distorted. •  Adjust the projector and the screen so that they are perpendicular to each other. (See 
page 11.)
Projected images are 
dark. •  Adjust BRIGHTNESS and CONTRAST in the IMAGE menu. (See page 28.)
•  Replace the lamp. (See page 39.)
Projected images are 
blurred. •  Adjust the focus. (See pages 15 and 20.)
• Clean the lens. 
• Press the 
W or 
X button on the remote control to eliminate fl icker. 
•  Adjust TRACKING and FINE SYNC. in the SIGNAL menu. (See page 31.)
•  Adjust BRIGHTNESS and CONTRAST in the IMAGE menu. (See page 28.)
•  Adjust the projector and the screen so that they are perpendicular to each other. (See 
page 11.)
Afterimages persist on 
the screen.•  This phenomenon is improved by keeping projecting an evenly bright image. (Such 
“image burn-in” phenomenon where afterimages persist on the screen may occur if a 
stationary image is kept displayed on the screen for a long time.)
Red, blue, and 
green dots appear in 
projected images. 
Black dots appear in 
projected images.•  This phenomenon is unique to LCD projector and isn’t a product malfunction. 
  (A small number of pixels always stay on or off, which are not malfunctions. More than 
99.99% of the pixels are effective.)
Fine streaks are seen 
on projected images. •  This is due to interference with the screen surface and is not a malfunction. Replace 
the screen or displace the focus a little. 
•  Vertical or horizontal streak noise may appear on the projected image, depending on 
the type of the DVD player or game console you use. In such a case, you can reduce 
such streak noise by enabling the LPF. 
Projected images 
become wavy. •  Connect the plugs of the cables to external devices securely. 
•  Keep the projector away from devices that emit interfering radio waves. 
•  When the keystone adjustment is carried out, the image may not be displayed 
correctly depending on the type of input signal. This isn’t a product malfunction. In 
this case, readjust the keystone so that the amount of keystone correction is as small 
as possible.
Hue is not appropriate. •  Check that the cables connected to the external devices are not broken. 
Tint in projected 
images is incorrect.•  Check that COMPUTER INPUT in the SIGNAL menu is correctly set. (See page 26.)
•  Check that the cable connected to the external device isn’t broken. 
Different color tint. •  When comparing images projected by two projectors, tints in the displayed images 
may be different because of variation between their optical components. This is not a 
malfunction. 
•  When comparing the image projected by this projector with those displayed on the 
television or PC monitor, tints in the displayed images may be different because of 
difference in the range of color reproducibility. This is not a malfunction.
Only the motion areas 
in the images supplied 
from the computer 
aren’t displayed. •  This is caused by the computer being used. Contact the manufacturer of your 
computer. 
						

							EN-44
Troubleshooting (continued)
Images are not displayed correctly. (continued) 
Problem Solution
Projected images are 
obscured.•  Match the output resolution of your computer with the resolution of the projector. For 
the method to change the output resolution of the computer, contact the manufacturer 
of your computer. (See page 46.)
•  Some images and texts appear obscured during the keystone adjustment. In such 
cases, use the projector without applying the keystone adjustment. (See page 11.)
Image cannot be 
displayed correctly 
even when the 
computer’s resolution 
is set to 1920 x 1080.•  Some computers output signals not supported by this projector even when its resolution 
is set to 1920 x 1080. Take the following procedures in order.
1.  Connect the computer to the COMPUTER/COMPONENT VIDEO IN 2 terminal and 
reboot the computer.
• DDC confi gures the computer so that it will output proper signals. (See page 14.) 
2.  Set the refresh rate of the computer to 60 Hz and make adjustment according to 
“How to adjust the computer image” on page 30.
•  When an unsupported signal is input, it may be displayed consisting of every 
other pixel. In this case, decrease the resolution of the computer.
Noise appears around 
the image. •  In some images such as DVD, noise may appear around the recorded image. In this 
case, decrease the setting value of OVER SCAN of the SIGNAL menu. (See page 26.)
Others
Problem Solution
The exhaust vents 
emit warm air.•  This air comes out after cooling the inside of the projector. You may feel hot, but this 
is not a malfunction. 
No audio is output.  •  Check that the volume isn’t set to low. 
The menu can’t be 
used. •  The microcomputers inside the projector may be wrongly operating because of noise. 
J  Turn off the main power, wait about 10 minutes, and turn on the main power again.
“TEMPERATURE!!” is 
displayed.•  This indication appears when the ambient temperature rises high. When the ambient 
temperature stays high, the lamp goes out.
J  Eliminate any causes of the rise in the ambient temperature.
•  This indication appears when the air inlet or outlet grille is blocked. When they are 
kept blocked, the lamp goes out. 
J  Remove the objects blocking the air inlet or outlet grille. 
The 
 mark appears.  •  This mark appears when ineffective operation is carried out. This isn’t a product 
malfunction. 
The remote control 
doesn’t function easily or 
at all.•  Check that the batteries are loaded in the remote control or the batteries are not weak. 
(See page 6.)
•  Check that the remote control sensor isn’t exposed to direct sunlight or fl uorescent 
light. (See page 9.)
•  Use the remote control within its operation range. (See page 9.)
•  Use the remote control at least 10 cm away from the projector. 
The buttons on the 
control panel (except 
for the POWER button) 
don’t function.•  PASSWORD FUNCTION in the FEATURE menu has been set to MENU ACCESS 
 to 
enable the password lock. 
J  Cancel the password lock or contact the person in charge of management of the 
projector. (See page 33.)
Alarm sounds. •  To temporarily halt the anti-theft alarm device, insert the safety pin. (See page 38.)
If the following problem occurs after the lamp is replaced, check the following fi rst. 
Problem Solution
The projector does not 
turn on. •  Fit the lamp cover securely. (See pages 39 and 40.)  
•  Reset the lamp operating time. (See page 40.)
The STATUS indicator 
blinks.•  Reset the lamp operating time. (See page 40.)
Kensington Lock
This projector has a Kensington Security Standard connector for use with Kensington MicroSaver Security System. 
Refer to the information that came with the Kensington System for instructions on how to use it to secure the 
projector. Please contact Kensington Technology Group below.
Kensington Technology Group
2855 Campus Drive
San Mateo, CA 94403, U.S.A.
Phone: +1- (650)572-2700  Fax: +1- (650)572-9675 
						

							EN-45
Specifi cations
The specifi cations and outside appearance of the projector are subject to change without prior notice.
Type LCD projector
Model FL7000U
Display technology 1.1-inch LCD panel: 3 pieces (for R,G,B)
Pixel: 1920 x 1080 = 2073600 pixels  Total 6220800 pixels
Active pixel rate: 99.99% or more (each panel)
Projection lens F 1.8 - 2.1  f= 51 - 64 mm
Light-source lamp 275 W
Image size (projection 
distance)60” min. to 250” max. (projection distance 2.6 to 11.2 m)
Maximum 
resolutionComputer 
signalMaximum resolution:  1920 x 1080 dots (Compressed in the case of 1600 x 1200 dots)
Panel resolution: 1920 x 1080 dots
Video signal NTSC/PAL/SECAM/4.43NTSC/PAL-M/PAL-N/PAL-60 
Component 
signal480i, 480p, 576i, 576p, 720p, 1080i, 1080p
Panel resolution: 1920 x 1080 dots
Computer/component video 
input[Signal type]  [Terminal type]  [Line]
Analog RGB  Mini D-SUB 15-pin  1
Analog RGB  5 BNC  1
Digital RGB  DVI  1
Video input [Signal type]  [Terminal type]  [Line]
Video input  RCA / BNC  1 
S-video input  S / 2 BNC  1
Audio input [Signal type]  [Terminal type]  [Line]
RGB/Component  Stereo mini jack (ø3.5)  2
Video RCA (L, R) 1
S-video RCA (L, R)  1
Monitor output [Signal type]  [Terminal type]  [Line]
Analog RGB  Mini D-SUB 15-pin  1
Audio output [Signal type]  [Terminal type]  [Line]
RGB/Component  Stereo mini jack (ø3.5)  1
Speaker 10 W Mono Round type ø4.5 cm x 1
Control terminal/others RS-232C (D-SUB 9-pin), USB, LAN (RJ-45), REMOTE IN/OUT
Operating temperatures +41°F (+5°C) to +104°F (+40°C)  
Rated voltage AC100 - 240 V, 50/60 Hz
Power consumption 4.4 A
Dimensions (not includeing 
protrusion)371 mm (W) x 207 mm (H) x 434 mm (D) (projector only)
443 mm (W) x 207 mm (H) x 434 mm (D) (including the terminal cover)
Weight 9.8 kg (projector only), 10.5 kg (including the terminal cover)
Others S-video input Luminance signal: Vp-p=1.0 V 75 Ω (negative sync)
Chrominance signals: Vp-p=0.286 V 75 Ω (burst signal)
Video input Vp-p=1.0 V  75 Ω (negative sync)
Component 
video inputYC
BCR: Vp-p=1.0 V 75Ω (Y) (negative sync)
  Vp-p=0.7 V 75 Ω (C
B, CR)
Analog input RGB: Vp-p=0.7 V 75 Ω (negative sync)
YC
BCR: Vp-p=1.0 V (Y) (negative sync)  Vp-p=0.7 V (CB, CR)
HD/CS: TTL-level (negative or positive polarity)
VD: TTL-level (negative or positive polarity)
Digital input (DVI)DVI-D interface (TMDS single link) with HDCP
Audio input 350 mVrms, 10 kΩ or more 
Replacement part (option/not included in the box)
Spare lamp: VLT-XL6600LP
Option lenses: OL-X500SZ, OL-X500LZ, OL-X500TZ, OL-X500FR(F)/OL-X500FR*
Front cabinet: CA-XL6600(FR)*
*: Use OL-X500FR and CA-XL6600(FR) in combination.  
						

							EN-46
Specifi cations  (continued)
Specifi cation of RGB signals in each computer mode of the projector
Signal mode Resolution
(H x V)Horizontal 
frequency (kHz)Vertical frequency 
(Hz)Normal mode
(H x V)Real mode
(H x V)
TV60, 480i (525i) 720 x 480 15.73 59.94 1440 x 1080 640 x 480
TV50, 576i (625i) 720 x 576 15.63 50.00 1440 x 1080 768 x 576
1080i60 (1125i60) 1920 x 1080 33.75 60.00 1920 x 1080 1920 x 1080 *1
1080i50 (1125i50) 1920 x 1080 28.13 50.00 1920 x 1080 1920 x 1080 *1
480p (525p) 720 x 480 31.47 59.94 1440 x 1080 640 x 480 *1
576p (625p) 720 x 576 31.25 50.00 1440 x 1080 768 x 576 *1
720p60 (750p60) 1280 x 720 45.00 60.00 1920 x 1080 1280 x 720 *1, *2
720p50 (750p50) 1280 x 720 37.50 50.00 1920 x 1080 1280 x 720 *1, *2
1080p60 (1125p60) 1920 x 1080 67.50 60.00 1920 x 1080 1920 x 1080 *1, *2
1080p50 (1125p50) 1920 x 1080 56.25 50.00 1920 x 1080 1920 x 1080 *1, *2
CGA70 640 x 400 31.47 70.09 1728 x 1080 640 x 400
CGA84 640 x 400 37.86 84.13 1728 x 1080 640 x 400
CGA85 640 x 400 37.86 85.08 1728 x 1080 640 x 400
VGA60 640 x 480 31.47 59.94 1440 x 1080 640 x 480 *1
VGA72 640 x 480 37.86 72.81 1440 x 1080 640 x 480
VGA75 640 x 480 37.50 75.00 1440 x 1080 640 x 480
VGA85 640 x 480 43.27 85.01 1440 x 1080 640 x 480
SVGA56 800 x 600 35.16 56.25 1440 x 1080 800 x 600
SVGA60 800 x 600 37.88 60.32 1440 x 1080 800 x 600 *1
SVGA72 800 x 600 48.08 72.19 1440 x 1080 800 x 600
SVGA75 800 x 600 46.88 75.00 1440 x 1080 800 x 600
SVGA85 800 x 600 53.67 85.06 1440 x 1080 800 x 600
SVGA95 800 x 600 59.97 94.89 1440 x 1080 800 x 600
XGA60 1024 x 768 48.36 60.00 1440 x 1080 1024 x 768 *1
XGA70 1024 x 768 56.48 70.07 1440 x 1080 1024 x 768
XGA75 1024 x 768 60.02 75.03 1440 x 1080 1024 x 768
XGA85 1024 x 768 68.68 85.00 1440 x 1080 1024 x 768
SXGA70a 1152 x 864 63.85 70.01 1440 x 1080 1152 x 864
SXGA75a 1152 x 864 67.50 75.00 1440 x 1080 1152 x 864
SXGA85a 1152 x 864 77.49 85.06 1440 x 1080 1152 x 864
WXGA60 1280 x 768 47.78 59.87 1800 x 1080 1280 x 768 *1
WXGA60a 1280 x 800 49.70 59.81 1728 x 1080 1280 x 800 *1
WXGA60b 1360 x 768 47.71 60.02 1912 x 1080 1360 x 768
WXGA60c 1366 x 768 47.50 59.75 1920 x 1080 1366 x 768
WXGA+60 1440 x 900 55.94 59.89 1728 x 1080 1440 x 900
SXGA60b 1280 x 960 60.00 60.00 1440 x 1080 1280 x 960
SXGA75b 1280 x 960 75.00 75.00 1440 x 1080 1280 x 960
SXGA85b 1280 x 960 85.94 85.00 1440 x 1080 1280 x 960
SXGA60 1280 x 1024 63.98 60.02 1350 x 1080 1280 x 1024 *1
SXGA75 1280 x 1024 79.98 75.02 1350 x 1080 1280 x 1024
SXGA85 1280 x 1024 91.15 85.02 1350 x 1080 1280 x 1024
SXGA+601400 x 1050 63.98 60.02 1440 x 1080 1400 x 1050
1400 x 1050 65.32 59.98 1440 x 1080 1400 x 1050 *1
SXGA+75 1400 x 1050 82.28 74.87 1440 x 1080 1400 x 1050
WSXGA+60 1680 x 1050 65.29 59.95 1728 x 1080 1680 x 1050
MAC13 640 x 480 35.00 66.67 1440 x 1080 640 x 480
MAC16 832 x 624 49.72 74.55 1440 x 1080 832 x 624
MAC19 1024 x 768 60.24 75.02 1440 x 1080 1024 x 768
HP75 1024 x 768 62.94 74.92 1440 x 1080 1024 x 768
HP72 1280 x 1024 78.13 72.00 1350 x 1080 1280 x 1024
SUN66a 1152 x 900 61.85 66.00 1382 x 1080 1152 x 900
SUN76a 1152 x 900 71.81 76.64 1382 x 1080 1152 x 900
SUN66 1280 x 1024 71.68 66.68 1350 x 1080 1280 x 1024
SUN76 1280 x 1024 81.13 76.11 1350 x 1080 1280 x 1024
SGI72 1280 x 1024 76.92 72.30 1350 x 1080 1280 x 1024
SGI76 1280 x 1024 82.01 76.00 1350 x 1080 1280 x 1024
UXGA60 1600 x 1200 75.00 60.00 1440 x 1080 - *1
*1:  Available with the signal for the DVI-D terminal.
*2: You can select from two adjustment modes by pressing the AUTO POSITION button. For details, see page 16. 
						

							EN-47
 1  R(RED)/PR/CR 2  G(GREEN)/Y
 3  B(BLUE)/P
B/CB 4  GND
 5  GND 
 6  GND 
 7  GND
 8  GND 
 9  DDC 5V
 10  GND 
 11  GND 
 12  DDC Data
 13  HD/CS
 14  VD
 15  DDC Clock 1 - - 2  TXD  IN
 3  RXD  OUT
 4 
-  - 
 5  GND - 6 - - 7 - - 
 8 - - 
 9 - -
1 5
116 10
15SERIAL (D-SUB 9-pin)
  Pin No.  Name  I/O
COMPUTER/COMPONENT VIDEO IN 2
(Mini D-SUB 15-pin)
 Pin No.  Spec.
COMPUTER/COMPONENT VIDEO 
DVI-D (HDCP)(DVI-D 24-pin)
 Pin No.  Spec.  Pin No.  Spec.
  1  TMDS DATA 2-  13 -  2  TMDS DATA 2+ 14 +5V Power
 3 TMDS DATA 2 Shield 15  Ground (for +5V)
 4 -  16  Hot Plug Detect
 5 -  17  TMDS DATA 0-
  6  DDC Clock   18  TMDS DATA 0+
 7  DDC Data  19 
TMDS DATA 0 Shield 8 - 20 -  9  TMDS DATA 1-  21 -  10  TMDS DATA 1+  22 TMDS Clock Shield 11 TMDS DATA 1 Shield   23  TMDS Clock+
 12 - 24 TMDS Clock-
1724
169
8
1
Connectors
434371 131.5
207
103
434
Dimension drawings (unit: mm)
Specifi cations  (continued)
1 5
6 9
Specifi cation of RGB signals in each computer 
mode of the projector (continued)
Important:
•  Some computers aren’t compatible with the projector.
•  The projector’s maximum resolution is 1920 x 1080 pix-
els. It may not display images of higher resolutions than 
1920 x 1080 correctly.
•  Images with SYNC on G (Green) signal may jitter.
•  Images with SYNC on G (Green) signal may be tinged 
with green.
•  If the resolution and frequency of your computer aren’t 
shown on the table, fi nd the compatible resolution and 
frequency by changing the resolution of your computer.
•  TV60 and TV50 are equivalent to 480i and 576i 
respectively. When these signals are supplied to the 
VIDEO IN or S-VIDEO IN terminal, the signal mode is 
indicated as TV60 or TV50. When they are supplied to 
the COMPUTER/COMPONENT VIDEO IN terminals, the 
signal mode is indicated as 480i or 576i. 
•  This projector doesn’t support 480p signals from video 
devices having 4 lines (R, G, B, CS*) or having 5 lines (R, 
G, B, H, V). 
  * : Composite Sync•  When a certain signal such as SXGA85, SXGA85b  
and UXGA60 is input, the number of displayed colors 
may decrease depending on the setting of ASPECT in 
the FEATURE menu. Change the signal format of the 
computer, if necessary.  
REAL modeWhen moire patterns or lines of uneven thickness appear 
on the projected image, these symptoms may be improved 
by displaying it in its original image size (REAL mode). To 
display the image in the REAL mode, set ASPECT of the 
FEATURE menu to REAL. (See page 23 for menu setting.)
•  In the REAL mode, you cannot change the magnifi cation 
factor and magnifi cation range. 
•  Images of which resolution is larger than the panel resolu-
tion cannot be displayed in the REAL mode.
•  In the REAL mode, images are black-framed when the 
image resolution is lower than the panel resolution.
443
207
434
434131.5
103
Without terminal cover
With terminal cover 
						

							MITSUBISHI Projector Contact Information
1 Zusho Baba, Nagaokakyo-City, Kyoto Japan
MITSUBISHI ELECTRIC CORPORATION
North America
MESCA (Mitsubishi Electric Sales Canada Inc.)
http://www.mitsubishielectric.ca
Information Technologies Group, 4299 14th Avenue, 
Markham, Ontario L3R 0J2, Canada
Sales & Technical Inquires
 Phone :+1-(800) 450-6487
 Fax :+1-(905) 475-7958
 E-mail :[email protected]
Customer Care
 E-mail :[email protected]
MDEA (Mitsubishi Digital Electronics America, Inc.)
(Warranty Registration)
http://www.mitsubishi-presentations.com/
Presentation Products Division, 9351 Jeronimo Road, 
Irvine, CA 92618 U.S.A
Sales & Inquires
 Phone :+1(888) 307-0349  or  +1(949)465-6000
 E-mail :[email protected]
Technical Inquires 
 Phone :+1-(888) 307-0309 
 E-mail :[email protected]  
    
Europe
MEU-FRA (Mitsubishi Electric Europe B.V French Branch)
25, Boulevard des Bouvets 92 741, Nanterre CEDEX, 
France
Sales Inquiries   
 Phone :+33 (0)1 55-68-55-53
 Fax :+33 (0)1 55-68-57-31
Techinical Inquireis   
 Phone :+33 (0)1 55-68-56-42 
 Fax :+33 (0)1 55-68-57-31 
MEU-GER (Mitsubishi Electric Europe B.V. German Branch)
http://www.mitsubishi-evs.de/
Gothaer Strasse 8, 40880 Ratingen, Germany
Sales Inquires   
  Phone  :0049 - 2102 - 486 9250 
  Fax  :0049 - 2102 - 486 7320 
Techinical Inquires   
  Phone  :0049 - 2102 - 486 1330   
  Fax  :0049 - 2102 - 486 1340 
MEU-IR (Mitsubishi Electric Europe B.V. Irish Branch)
http://www.mitsubishi.ie/
Westgate Business Park, Ballymount, Dublin 24, Ireland
Sales Inquiries   
 Phone :+353-1-4198807 
 Fax :+353-1-4198890 
Technical Inqiries   
 Phone :+353-1-4198808 
 Fax :+353-1-4198895 
MEU-IT (Mitsubishi Electric Europe B.V. Italian Branch)
Centro Direzionale Colleoni, Palazzo Sirio, Viale Colleoni 7, 
20041 Agrate Brianza, Italy
Sales & Technical Inquiries  
 Phone :+39-(0)39-60531 
 Fax :+39-(0)39-6053214 
 E-mail :[email protected] 
MEU-NL (Mitsubishi Electric Europe B.V. Benelux Branch)
http://www.mitsubishi.nl/LCD/ProdFrame.html
Nijverheidsweg 23A, 3641 RP Mijdrecht, The Netherlands 
Sales Inquiries   
 Phone :+31-297-282461 
 Fax :+31-297-283936 
 E-mail :[email protected] 
Techinical Inquiries   
 Phone :+31-297-282461 
 Fax :+31-297-283936 
 E-mail :[email protected] 
Russia (Mitsubishi Electric Europe B.V Moscow 
Representative Offi ce)
http://www.mitsubishi-projector.ru/
Moscow Representative Offi ce, 52/5 Kosmodamianskaya 
Nab., 115054, Moscow, Russia
Sales & Techinical Inquiries   
 Phone :(7095) 721-2068 
 Fax :(7095) 721-2071 MEU-SP (Mitsubishi Electric Europe B.V. Spanish Branch)
http://www.mitsubishielectric.es/
Ctra. de Rubi, 76-80, 08173 Sant Cugat del Valles, 
Barcelona, Spain
Sales Inquiries   
 Phone :+34-93.565.31.54 
 Fax :+34-93.589.43.88 
 E-mail :[email protected]
Technical Inquiries   
 Phone :+34-93.586.27.51 
 Fax :+34-93.588.53.87 
 E-mail :[email protected]
MEU-SWE (Mitsubishi Electric Europe B.V Scandinavian 
Branch)
Hammarbacken 14, Box 750, S-19127, Sollentuna, Sweden
Sales Inquiries   
 Phone :+46-(0)8-6251070 
 Fax :+46-(0)8-6251036 
Technical Inquiries   
 Phone :+46-(0)8-6251052 
 Fax :+46-(0)8-6251036 
MEU-UK (Mitsubishi Electric Europe)
http://www.mitsubishi.co.uk/evs/
Visual Information Systems Division, Travellers Lane, 
Hatfi eld, Hertfordshire, AL10 8XB U.K.   
Sales Inqiries   
 Phone :+44 (1707) 278684 
 Fax :+44 (1707) 278541 
 E-mail :[email protected] 
Technical Inquiries   
  Phone  :+44 (870) 606 5008 
 Fax :+44 (1506) 431927 
 E-mail :[email protected] 
Asia
CHINA (Mitsubishi Electric Air-Conditioning & Visual 
Information Systems (Shanghai) Ltd.)     
26/F., Oriental Center, 699 Nanjing Rd(W), Shanghai, 
200041, China 
Sales Inquiries     
 Phone :+86(21) 5211-0882-3002 
 Fax :+86(21) 5211-0576
Technical Inquiries     
 Phone :+86(21) 5211-0882-3020  
 Fax :+86(21) 5211-0576 
HONG KONG (Mitsubishi Electric Ryoden Air-Conditioning 
& Visual Information Systems (HongKong) Ltd.) 
7th Floor, Manulife Tower, 169 Electric Road, North Point, 
Hong Kong   
Sales Inquiries   
 Phone :+852-2510-1505 
 Fax :+852-2510-0463 
Technical Inquiries   
 Phone :+852-2422-0161 
 Fax :+852-2487-0181 
SINGAPORE (Mitsubishi Electric Asia Pte. Ltd.) 
http://www.mitsubishielectric.com.sg
307, Alexandra Road, #05-01/02 Mitsubishi Electric 
Building, Singapore 159943
Sales Inquiries   
 Phone :+65-6473-2308 
 Fax :+65-6475-9503 
 E-mail :[email protected] 
Technical Inquiries   
 Phone :+65-6470-2666 
 Fax :+65-6475-9503 
INDIA (Mitsubishi Electric Asia Pte. Ltd.)
307, Alexandra Road, #05-01/02 Mitsubishi Electric 
Building, Singapore 159943
Sales Inquiries   
 Phone :+65-6473-2308 
 Fax :+65-6475-9503 
 E-mail :[email protected] 
Technical Inquiries   
 Phone :+65-6470-2666 
 Fax :+65-6475-9503 INDONESIA (Mitsubishi Electric Asia Pte. Ltd.)
307, Alexandra Road, #05-01/02 Mitsubishi Electric 
Building, Singapore 159943
Sales Inqiries   
 Phone :+65-6473-2308 
 Fax :+65-6475-9503 
 E-mail :[email protected] 
Technical Inquiries   
 Phone :+65-6470-2666 
 Fax :+65-6475-9503 
PHILLIPINES (Mitsubishi Electric Asia Pte. Ltd.) 
http://www.mitsubishielectric.com.sg
307, Alexandra Road, #05-01/02 Mitsubishi Electric 
Building, Singapore 159943
Sales Inquiries   
 Phone :+65-6473-2308 
 Fax :+65-6475-9503 
 E-mail :[email protected] 
Technical Inqiries   
 Phone :+65-6470-2666 
 Fax :+65-6475-9503 
VIETNAM (Mitsubishi Electric Asia Pte. Ltd.) 
307, Alexandra Road, #05-01/02 Mitsubishi Electric 
Building, Singapore 159943 
Sales Inquiries
 Phone :+65-6473-2308 
 Fax :+65-6475-9503 
 E-mail :[email protected] 
Technical Inquiries   
 Phone :+65-6470-2666 
 Fax :+65-6475-9503 
STC (Setsuyo Astec Corporation Seoul Branch) 
4F,Dongseo Game Channel Bldg,660-11 Deungchon-Dong, 
Kangseo-Ku, Seoul, Korea  
Sales & Technical Inqiries   
 Phone :+82-(0)2-2657-9841~3 
 Fax :+82-(0)2-2657-9900 
MALAYSIA (Antah Melco Sales & Services Sdn. Bhd.)
6, Jalan 13/6 46860 Petaling Jaya Selangor, Darul Ehsan, 
Malaysia 
Sales & Technical Inquiries  
  Phone  :+60-(0)3-79552088  (Ext. 203) 
 Fax :+60-(0)3-79563950/+60-(0)3-79582576
Technical & Service Inquiries   
 Phone :+60-(0)3-79552088 (Ext. 106) 
 Fax :+60-(0)3-79563950/+60-(0)3-79582576
ME-TWN (Mitsubishi Electric Taiwan Co., Ltd.)
http://www.MitsubishiElectric.com.tw
11TH FL., 90 SEC. 6, CHUNG SHAN N. RD., TAIPEI, 111 
R.O.C.
Sales & Technical Inquires     
 Phone :+886-2-2832-8255
 Fax :+886-2-2833-9813 
MKY (Mitsubishi Electric Kang Yong Watana Co., Ltd. )
http://www.mitsubishi-kyw.co.th/
Road, Huamark Bangkapi, Bangkok 10240, Thailand 
Sales & Technical Inquiries  
 Phone :+66-2-731-6841 
 Fax :+66-2-379-4763 
Oceania
ME-AUST (Mitsubishi Electric Australia)
http://www.mitsubishi-electric.com.au/prod.asp?prod=proj
348 Victoria Road, Rydalmere, N.S.W. 2116, Australia Sales 
& Technical Inqiries     
 Phone :+(612)9684-7777
 Fax :+(612)9684-7208 
 E-mail :[email protected]
Technical Inquiries   
 Phone :+(612)9684-7694 
 Fax :+(612)9684-7684 
 E-mail :[email protected] 
BDT (Black Diamond Technologies Ltd.)
(Warranty Registration)  http://www.bdt.co.nz/projectors/
warranty.asp
1 Parliament St, Lower Hutt, Wellington, New Zealand Sales 
Inquiries  
 Phone :+64-(0)4-560-9100 
 Fax :+64-(0)4-560-9133 
 E-mail :[email protected] 
Technical Inquiries   
 Phone :+64-(0)4-560-9100 
 Fax :+64-(0)4-560-9133 
 E-mail :[email protected]
B