Mitsubishi Fl6900u Projector User Manual

EN-11
Setting up your projector  (continued)
Adjusting the position of the projected image
To adjust the position of the projected image on the screen, use the LENS SHIFT button.
1.  Press the LENS SHIFT button.
•  The LENS SHIFT menu appears at the center of the screen.
2. Press the 
S, 
T, 
W or 
X button to move the image position.
• When the 
T button is pressed, the image moves down.
• When the 
S button is pressed, the image moves up.
• When the 
X button is pressed, the image moves to the right.
•...

EN-12
Setting up your projector  (continued)
Front projection, ceiling mounting
For ceiling mounting, you need the ceiling mount kit 
designed for this projector. Ask a specialist for installa-
tion. For details, consult your dealer.
•  The warranty on this projector does not cover any 
damage caused by use of any non-recommended 
ceiling mount kit or installation of the ceiling mount 
kit in an improper location. 
•  When using the projector mounted on the ceiling, 
set IMAGE REVERSE in the INSTALLATION...

EN-13
Viewing computer images
2 1
AUDIO OUTAUDIO IN 1/2
2 1
2 1
A. Connecting the projector to a computer
Preparation: 
•  Make sure that the power of the projector and that of the computer are turned off. 
•  When connecting the projector to a desktop computer, disconnect the RGB cable that is connected to the monitor. 
For analog connection: 
(For using the COMPUTER/COMPONENT VIDEO IN 2 
terminal.)
1.  Connect one end of the supplied RGB cable to the 
COMPUTER/COMPONENT VIDEO IN 2 terminal of the...

EN-14
Viewing computer images (continued)
2 1
1.  Plug the attached power cord into the power cord inlet of 
this projector.
2.  Plug the other end of the power cord into a power outlet.
•  The power cords for use in the U.S. and Europe are included with this projector. Use the appropriate one for your 
country. 
•  This projector uses the power plug of 3-pin grounding type. Do not take away the grounding pin from the power 
plug. If the power plug doesn’t fi t your wall outlet, ask an electrician to...

EN-15
Viewing computer images (continued)
C. Projecting images
Preparation:
•  Remove the lens cap.
1.  Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red. 
•  If the projector was turned off before the lamp was cooled down suffi ciently last time, the fan may start rotating 
and the POWER button may not work after the main power switch is turned ON. (The STATUS indicator blinks 
green.) After the fan stops rotating, press the POWER button to turn back...

EN-16
Viewing computer images (continued)
Important:
•  Focus, zoom and lens shift adjustment is possible in the normal picture mode only.
•  When a 4:3 image is kept displayed for a long time before displaying 16:9 image, the afterimages of the black bars 
may appear on the 16:9 image screen. (See page 43.)
To stop projecting:
13. Press the POWER button. 
• A confi rmation message is displayed.
•  To cancel the procedure, leave the projector for a while or press any button except the POWER button. 
14....

EN-17
Viewing video images
Connecting to a video player, etc.
1.  Connect one end (yellow) of the supplied audio/video cable 
to the VIDEO IN terminal of the projector. 
2.  Connect one end (white and red) of the supplied audio/
video cable to the audio input terminals (L/MONO, R) of the 
projector. 
3.  Connect the other end (yellow) of the audio/video cable to 
the video output terminal of the video equipment. 
4.  Connect the other end (white and red) of the audio/video 
cable to the audio output...

EN-18
Connecting to video equipment having a HDMI terminal or DVI-D terminal
You can project high-quality images by connecting the COMPUTER/COMPONENT VIDEO DVI-D (HDCP) terminal of 
this projector to video equipment having a HDMI output terminal or DVI-D terminal. In addition, this projector supports 
HDCP and is able to receive encrypted digital video data that are output from DVD players.
• HDCP (High-bandwidth Digital Content Protection), developed by Intel Corporation, is a method to encrypt digital...

EN-19
Equipment having a 
DVI-D terminalTo audio output 
terminalsAudio cable (option)
To audio input 
terminals
To DVI-D terminal
DVI cable (option)COMPUTER/COMPONENT 
VIDEO DVI-D (HDCP)
Connection (for video equipment having a DVI-D terminal)
•  For connection to the DVI-D terminal, use a commercially available DVI cable. 
•  Some cables may not be connected correctly depending on the size and shape of their connectors.
•  When DVI is selected as the input source, settings of FINE SYNC., TRACKING,...

EN-20
Viewing video images (continued)
C. Projecting images
Preparation:
•  Remove the lens cap.
1.  Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red. 
•  If the projector was turned off before the lamp was cooled down suffi ciently last time, the fan may start rotating and 
the POWER button may not work after the main power switch is turned ON. (The STATUS indicator blinks green.) 
After the fan stops rotating, press the POWER button to turn back on...