Mitsubishi Fd730u Projector User Manual

							DLP™ PROJECTOR
MODEL
FD730U
FD730U-G
User Manual
This User Manual is important to you.
Please read it before using your projector.
FD730U
FD730U-G 
						

							EN-2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC 
SHOCK, DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE 
PERSONNEL.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert 
the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure 
that may be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to aler\
t the user to the 
presence of important operating and maintenance (servicing) instructions\
 in the literature 
accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR\
 MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EX\
TENSION CORD, 
RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE 
EXPOSURE.
NOTE:
SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR 
THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.
WARNING
Use the attached specified power supply cord. If 
you use another power supply cord, it may cause 
interference with radio and television reception.
This apparatus must be grounded.
DO NOT LOOK DIRECTLY INTO THE LENS WHEN 
THE PROJECTOR IS IN THE POWER ON MODE.
CAUTION
The attached power cord is to be used exclusively for 
this product. Never use it for other products. 
						

							EN-3
Contents
Important safeguards ........................................................................\
................................................4
Overview ............................................................................................\
................................................6
Remote control  ...........................................................................................\
.......................................8
Installation   ...........................................................................................\
.............................................9
Basic connections ........................................................................\
...................................................11
Preparation  ...........................................................................................\
..........................................14
Basic operation  ........................................................................\
.......................................................16
Menu operation ........................................................................\
.......................................................19
Image adjustment ........................................................................\
....................................................27
Network settings  ........................................................................\
.....................................................30
Advanced features  ........................................................................\
..................................................33
Lamp replacement  ........................................................................\
..................................................37
Troubleshooting ........................................................................\
.......................................................39
Indicators ............................................................................................\
.............................................43
Specifications  ...........................................................................................\
.......................................44
Trademark, Registered trademark
•	 Macintosh	is	a	registered	trademark	of	Apple	Inc.
•	 DLP™,	Digital	Micromirror	Device,	DMD,	and	BrilliantColor™	are	all	trademarks	of	Texas	Instruments.
•	 HDMI,	the	HDMI	logo	and	High-Definition	Multimedia	Interface	are	trademarks	or	registered	trademarks	of	HDMI	
Licensing LLC.
•	 Microsoft,	Windows,	Windows	2000,	Windows	XP,	Windows	Vista,	Windows	7,	and	Internet	Explorer	are	
registered trademarks, trademarks, or trade names of Microsoft Corporation in the U.S. and/or other countries.
•	 The	trademark	of	PJLink	is	trademark	applied	for	registration	or	registered	trademark	in	Japan,	the	United	States,	
and other countries and areas.
•	 Other	brand	or	product	names	are	trademarks	or	registered	trademarks	of	their	respective	holders. 
						

							EN-4
Important safeguards
Please read all these instructions regarding your 
projector and retain them for future reference. Follow 
all warnings and instructions marked on the projector.
1. Read instructions
 All the safety and operating instructions should be 
read before the appliance is operated.
2. Retain instructions
 The safety and operating instructions should be 
retained for future reference.
3. Warnings
 All warnings on the appliance and in the operating 
instructions should be adhered to.
4. Instructions
 All operating instructions must be followed.
5. Cleaning
 Unplug this projector from the wall outlet before 
cleaning it. Do not use liquid aerosol cleaners. Use 
a damp soft cloth for cleaning.
6. Attachments and equipment
 Never add any attachments and/or equipment 
without the approval of the manufacturer as such 
additions may result in the risk of fire, electric 
shock or other personal injury.
7. Water and moisture
 Do not use this projector near water or in contact 
with water.
8. Accessories
 Do not place this projector on an unstable cart, 
stand, tripod, bracket or table. Use only with a 
cart, stand, tripod bracket, or table recommended 
by the manufacturer or sold with the projector. 
Any mounting of the appliance should follow 
the manufacturer’s instructions and should use 
a mounting accessory recommended by the 
manufacturer.
10. Power sources
 This projector should be operated only from the 
type of power source indicated on the marking 
label. If you are not sure of the type of power, 
please consult your appliance dealer or local 
power company.
11. Power-cord protection
 Power-supply cords should be routed so that 
they are not likely to be walked on or pinched 
by items placed upon or against them. Pay 
particular attention to cords at plugs, convenience 
receptacles, and points where they exit from the 
appliance. Do not put the power cord under a 
carpet.
12. Overloading
 Do not overload wall outlets and extension cords 
as this can result in a fire or electric shock.
13. Objects and liquids
 Never push objects of any kind through openings 
of this projector as they may touch dangerous 
voltage points or short-out parts that could result 
in a fire or electric shock. Never spill liquid of any 
kind on the projector.
14. Servicing
 Do not attempt to service this projector by yourself. 
Refer all servicing to qualified service personnel. 
15. Damage requiring service
 Unplug this projector from the wall outlet and refer 
servicing to qualified service personnel under the 
following conditions:
(a) If the power-supply cord or plug is damaged.
(b) If liquid has been spilled, or objects have fallen 
into the projector.
(c) If the projector does not operate normally after 
you follow the operating instructions. Adjust 
only those controls that are covered by the 
operating instructions. An improper adjustment 
of other controls may result in damage and 
may often require extensive work by a qualified 
technician to restore the projector to its normal 
operation.
(d) If the projector has been exposed to rain or 
water.
(e) If the projector has been dropped or the 
cabinet has been damaged.
(f) If the projector exhibits a distinct change in 
performance - this indicates a need for service.
16. Replacement parts
 When replacement parts are required, be sure 
that the service technician has used replacement 
parts specified by the manufacturer or parts 
having the same characteristics as the original 
part. Unauthorized substitutions may result in fire, 
electric shock or other hazards.
17. Safety check
 Upon completion of any service or repair to this 
projector, ask the service technician to perform 
safety checks determining that the projector is in a 
safe operating condition.
 An appliance and cart combination should be 
moved with care. Quick stops, excessive force and 
uneven surfaces may cause the appliance and cart 
combination to overturn.
9. Ventilation
 Slots and openings in the cabinet are provided 
for ventilation, ensuring reliable operation of the 
projector and to protect it from overheating. Do 
not block these openings or allow them to be 
blocked by placing the projector on a bed, sofa, 
rug, or bookcase. Ensure that there is adequate 
ventilation and that the manufacturer’s instructions 
have been adhered to. 
						

							EN-5
Important safeguards (continued)
WARNING:
Unplug immediately if there is something wrong 
with your projector.
Do not operate if smoke, strange noise or odor comes 
out of your projector. It may cause fire or electric 
shock. In this case, unplug immediately and contact 
your dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An 
inadvertent contact may result in an electric shock. 
Except as specifically explained in User Manual, do 
not attempt to service this product by yourself. Please 
contact your dealer when you want to fix, adjust, or 
inspect the projector.
Do not modify this equipment.
It can lead to fire or electric shock.
Do not keep using the damaged projector.
If the projector is dropped and the cabinet is 
damaged, unplug the projector and contact your 
dealer for inspection. It may lead to fire if you keep 
using the damaged projector. 
Be sure to unplug the power cord from the wall 
outlet if the projector is fractured or deformed.
Otherwise, it may result in fire or electric shock. Ask 
your dealer for repair.
Do not face the projector lens to the sun.
It can lead to fire.
Use correct voltage.
If you use incorrect voltage, it can lead to fire.
Do not place the projector on uneven surface. 
Place the projection on a leveled and stable surface only. 
Do not look into the lens when it is operating.
It may hurt your eyes. Never let children look into the 
lens when it is on.
Do not put any objects immediately in front of the 
lens while the lamp is on.
The lens and the objects get hot and can cause fire or 
breakdown. 
Do not unplug the power cord during operation.
It can lead to lamp breakage, fire, electric shock or 
other trouble.
Do not touch the exhaust vents and bottom plate.
Do not touch them or put other equipment close to 
the exhaust vents because they become hot during 
operation. The heated exhaust vents and bottom 
plate may cause injury or damage to other equipment. 
Also, do not put the projector on a desk that is easily 
affected by heat.
Do not look into the exhaust vents when projector 
is operating.
Heat, dust, etc. may blow out of them and hurt your eyes.
Do not block the intake and exhaust vents.
If they are blocked, heat may be generated inside the projector, 
causing deterioration in the projector quality and fire.
Do not use flammable solvents (benzene, thinner, 
etc.) and flammable aerosols near the projector.
Flammable substances may ignite causing fire or 
breakdown because the temperature inside the 
projector rises very high while the lamp is illuminating. 
Do not use the projector with condensation on it. 
It can lead to breakdown or other failure. 
Place of installation
For safety’s sake, do not use the projector at any place 
subjected to high temperature and high humidity. 
Please maintain an operating temperature, humidity, 
and altitude as specified below.
•	 Operating	temperature:	between	+41°F	(+5°C)	and	
+95°F	(+35°C)
•	 Operating	humidity:	between	30%	and	90%
•	 Never	put	any	heat-producing	device	under	the	
projector to prevent the projector from being 
overheated.
•	 Do	not	install	the	projector	at	a	place	that	is	
unstable or subject to vibration.
•	 Do	not	install	the	projector	near	any	equipment	that	
produces a strong magnetic field. Also refrain from 
installing the projector near any cable carrying a 
large amount of current.
•	 Place	the	projector	on	a	solid,	vibration-free	
surface. Otherwise it may fall, causing serious injury 
or damage.
•	 Do	not	stand	the	projector	on	its	end.	It	may	fall,	
causing serious injury or damage.
•	 Slanting	the	projector	more	than	±10°	(right	and	
left)	or	±15°	(front	and	rear)	may	cause	trouble	or	
explosion of the lamp.
•	 Do	not	place	the	projector	near	air-conditioning	
unit, heater, or humidifier to avoid hot or moist air 
to the exhaust and ventilation hole of the projector.
•	Do not place the projector in the following places. 
Otherwise, a short circuit, heat generation, or melting 
of the power cord coating may occur, causing fire, 
electric shock, product failure, or deformation.
•	 Outdoors	or	non	air-conditioned	place
•	 Place	where	a	gas	such	as	a	hydrogen	sulfide	is	
generated (i.e. hot spring)
•	 Place	where	there	is	too	much	salt	such	as	near	
the coast
•	 Be	sure	to	use	this	projector	at	an	altitude	of	less	
than 1500 meters.
Do not place a container containing water or other 
liquid on the projector.
If water spills on or enters the projector, it may result in 
fire or electric shock.
Do not put any object that is heavy or larger than 
the outer frame on the projector.
Otherwise, the object may fall losing its balance and 
cause injury.
Do not subject the projector to strong shocks or 
vibrations. Do not handle the projector roughly.
The projector may be damaged, resulting in fire or 
electric shock.
When removing the lamp from the ceiling-mounted 
projector 
Be sure to use the lamp replacement attachment 
designed specifically for this projector when replacing 
the lamp with a new one. Lamp fragments may fall 
from the inside if the lamp were broken.
Do not put the projector in the soft case with the 
power cord and cables connected. 
The projector, power cord, or cables may be damaged. 
						

							EN-6
16789
23
4
10 11
13 14
12 5
1 
Lamp cover
2 Lens
3 FOCUS ring
4 ZOOM ring
5 LENS SHIFT dial
6 Remote control sensor (front)
7 Speaker
8 Lock bar
9 Intake vent
10 Control panel
11 Exhaust vent
12 Power jack
13 Terminal panel
14 Kensington Lock
Caution:
•	 Do	not	replace	the	lamp	immediately	after	using	the	
projector because the lamp would be extremely hot 
and it may cause burns.
Control panel
1 AUTO POSITION/ button
2 EFFICIENT MODE button
3 STATUS indicator
4 POWER indicator
5 COMPUTER/ button
6  button
7 VIDEO/ button
8 KEYSTONE/ENTER button
9 MENU button
10 POWER button (ON/STANDBY)
The status is changed between ON and STANDBY.
13 24 5678
1011 12
9
1  Remote control sensor (rear)
2 S-VIDEO terminal
3 AUDIO IN-3 terminals (L, R)
4 MONITOR OUT terminal (mini D-SUB 15-pin)
5 AUDIO IN-1 terminal (mini jack)
6 COMPUTER/COMPONENT VIDEO IN terminals (1, 2) 
(mini D-SUB 15-pin)
7 HDMI terminal (HDMI 19-pin)
8 SERIAL (RS-232C) terminal (D-SUB 9-pin)
9 VIDEO terminal
10 AUDIO OUT terminal (mini jack)
11 AUDIO IN-2 terminal (mini jack)
12 LAN terminal (RJ-45)
Terminal panel
Overview
1
3
2 4
67 89 10
5 
						

							EN-7
1
Overview (continued)
Bottom side1 Adjustment feet
Remote control
1 ON button
2 MAGNIFY button
3 VOLUME UP, DOWN buttons
4 KEYSTONE button
5 MENU button
6 ENTER button
7 AV (Audio/Video) MUTE button
8 STANDBY button
9 ASPECT button
10 EFFICIENT MODE button
11 AUTO POSITION button
12 , , ,   buttons
13 FREEZE button
14 VIDEO, S-VIDEO buttons
15 COMPUTER (1, 2) buttons
16 HDMI button
ON
ASPECT
EFFICIENTMODE
MA GNIFY
KEYST ONE VO
L
UP
3DDO WN
STANDBY
MENU
FREEZE
AU
TO
P OSI TION
AV
MUTE
ENTER
1
2COMPUTER VIDEO
VIEWER
UNPLUGS-VIDEO
USB DISP.
LAN DISP.DVI HDMI
1
2
3
4
5
6
7
14
15 11
12
13
168
9
10
This model does not have these functions.
This model does not have this function. 
						

							EN-8
Remote control
Battery installation
Use two (AA, R6) size batteries.
Inserting the batteries into the remote control
1. Remove the back cover of the remote control by pushing the battery compartment door in the direction of the arrow.
2.	 Load	the	batteries	making	sure	that	they	are	positioned	correctly	(+	to	+,	and	-	to	-).
•	 Load	the	batteries	from	-	spring	side,	and	make	sure	to	set	them	tightly.
3. Replace the back cover.
Removing the batteries from the remote control
Remove the back cover of the remote control and take out the batteries.
Caution: •	 Use	of	a	battery	of	wrong	type	may	cause	explosion.•	 Only	Carbon-Zinc	or	Alkaline-Manganese	Dioxide	type	batteries	should	be	used.	•	 Dispose	of	used	batteries	according	to	your	local	regulations.	•	 Before	you	dispose	of	the	batteries,	insulate	them	by	placing	insulation	tape	on	the	positive	(+)	and	negative	(-)	terminals. If you dispose of the batteries together with other conductiv\
e objects such as a metal piece, they may short out, resulting in fire or explosion.•	Batteries may explode if misused. Do not recharge, disassemble, or heat the batteries, or put them into fire or water.•	 Be	sure	to	handle	the	batteries	according	to	the	instructions.•	 Load	the	batteries	with	its	positive	(+)	and	negative	(-)	sides	correctly	oriented	as	indicated	on	the	remote	control.	•	 Keep	batteries	out	of	reach	of	children	and	pets.	If	children	swallow	the	battery,	see	a	doctor	immediately.•	 Remove	the	batteries,	if	the	remote	control	is	not	used	for	a	long	time.	•	 Do	not	combine	a	new	battery	with	an	old	one.•	 If	the	solution	of	batteries	comes	in	contact	with	your	skin	or	clothes,	rinse	with	water.	If	the	solution	comes	in	contact	with your eyes, rinse them with water and then consult your doctor.•	 Do	not	carry	or	store	the	batteries	together	with	metallic	ballpoint	pens,	necklaces,	coins,	or	hairpins.	Otherwise,	they	may short out, causing explosion or liquid leakage and resulting in fire or injury.•	 Do	not	store	the	batteries	where	they	are	exposed	to	direct	sunlight	or	subjected	to	high	temperature	and	high	humidity.	
High temperature and high humidity may cause corrosion or liquid leakage.
Operation range (of the remote control)
The maximum operation distance of the remote control is about 10 m (or about 32 feet) when the remote control is 
pointed at the remote control sensor of the projector. When the remote control is pointed to the screen, the distance 
from the remote control to the projector via the screen should be 5 m or less. However, the operation distance varies 
depending on the type of the screen used.
Reception angle (horizontal)Reception angle (vertical)
30°
30°
10°
20°
10° 20°
Reception angle (vertical), ceiling mount
20°
20°
Important:
•	 Do	not	expose	the	remote	control	sensor	to	direct	sunlight	or	fluorescent.	Keep	a	distance	at	least	2	m	(6.5	feet)	
between the remote control sensor and the fluorescent light to ensure correct operation of the remote control.
 Inverted fluorescent light, if located near the projector, may interfere the remote control.
•	When you use the remote control too close to the remote control sensor, the remote control may not work correctly. 
						

							EN-9
Screen size and projection distance
Refer to the following tables to determine the screen size and projection distance.
•	 The	figures	in	the	tables	are	approximate	and	may	be	slightly	different	from	the	actual	measurements.
•	 The	lens	shift	height	shows	distances	from	the	factory	default	position.
Screen width (SW)
Down side
Up side
Scr
een
Screen height (SH)
Hd
H1
H2
L
Screen size (16:9)HdProjection distance (L)Lens shift height
Diagonal sizeWidth (SW)Height (SH)Shortest (Wide)Longest (Tele)H1H2
inchcminchcminchcminchcminchminchminchcminchcm40102358920506.617471.2711.83726601525213329751025711.81072.7411498020370177391001334962.41443.6614512100254872214912516421203.11804.6718616120305 1052665914920501453.72165.58217191503811313327418725631824.62716.911279232005081744439824933842436.23629.214361231
250635218553123311411053047.7--18451539300762261664147374491263659.3--21541847
When the aspect ratio of the screen is 4:3
When the aspect ratio of the screen is 4:3, the positional relation between  
the projected image and the screen is as shown on the right. Refer to the 
following table for installation.
• When the aspect ratio of the image is 16:9
Screen size (4:3)Size of the projected image (16:9)Black space (B)HdProjection distance (L)Lens shift height
Diagonal sizeWidth (SW)Height (SH)Diagonal sizeWidth (W)Height (H)Shortest (Wide)Longest (Tele)H1H2
inchcminchcminchcminchcminchcminchcminchcminchcminchminchminchcminchcm4010232812461379332811846386.115431.1651.637266015248122369155140481222769511923651.7982.541039802036416348122731876416336916151231882.21323.351341110025480203601529223380203 4511481915381102.81654.2616614120305 9624472183110280962445413792318461333.41995.08207171503811203059022913835012030568171112923581664.22496.3102582120050816040612030518446616040690229153830772235.73328.413331129
250635200508150381229583200508113286194838962797.1--164114363007622406101804572756992406101353432357451153358.5--19491743
Installation
Screen (4:3)
Image (16:9)
B B
HSH
SW (=W) 
						

							EN-10
Installation (continued)
Front projection, ceiling mounting
For ceiling mounting, you need the ceiling mount 
kit designed for this projector. Ask a specialist for 
installation. For details, consult your dealer.
•	 The	warranty	on	this	projector	does	not	cover	any	
damage caused by use of any non-recommended 
ceiling mount kit or installation of the ceiling mount 
kit in an improper location.
•	 When	using	the	projector	mounted	on	the	ceiling,	
set IMAGE REVERSE in the INSTALLATION menu 
to MIRROR INVERT. See page 23.
•	 When	the	projector	is	mounted	on	the	ceiling,	
images may appear darker than those projected in 
the case of tabletop mounting. This isn’t a product 
malfunction.
Ceiling mount installation
If you wish to install the projector using a ceiling 
mount, please use the screw holes as the illustration 
shows.
Important:
•	 Screws	are	not	included.	Please	obtain	the	
appropriate screws for your type of ceiling. (M4 
diameter)
•	 It	is	recommended	that	you	keep	a	reasonable	
space between the bracket and the projector to 
allow for proper heat distribution.
Caution:
•	 Installation	must	be	done	by	a	qualified	
professional. 
 When the projector is installed on the ceiling using 
the ceiling mount kit, it is recommended to hold 
the mount kit and the projector using a metal bar 
or wire in addition to the mount kit fixing screws 
to prevent the projector from falling due to an 
earthquake or other cause. For that purpose, use 
a metal bar, wire, or screw that bears a load of at 
least 55 kgf. When using a metal wire, secure one 
end to a screw hole marked with an arrow on the 
rear terminal panel and the other end to the mount 
kit. (Don’t use screw holes without arrow marks.) In 
this case, make sure that the screw is inserted in 
the projector at least 5 mm. The length of the screw 
should be 20 mm or shorter. Also make sure that 
no electrical current is flowing in the mount kit due 
to current leakage or other cause. 
Rear projection
Ask a specialist for installation. For details, consult 
your dealer.
•	 For	rear	projection,	set	IMAGE	REVERSE	in	the	
INSTALLATION menu to MIRROR. See page 23.
Caution:
•	 Placing	the	projector	directly	on	a	carpet	impairs	
ventilation by the fans, causing damage or failure. 
Put a hard board under the projector to facilitate 
ventilation.
•	 Place	the	projector	at	least	50	cm	(or	20	inch)	away	
from the wall to prevent the intake vents and the 
exhaust vents that emit hot air from being blocked.
•	 Do	not	use	the	projector	in	the	following	locations	
and manners, which may cause fire or electric 
shock.
•	 In	a	dusty	or	humid	place.
•	 In	a	sideways	or	upside-down	position.
•	 Near	a	heater.
•	 In	an	oily,	smoky,	or	damp	place	such	as	a	
kitchen.
•	 In	direct	sunlight.
•	 Where	the	temperature	rises	high,	such	as	in	a	
closed car.
•	 Where	the	temperature	is	lower	than	+41°F	(or	
+5°C)	or	higher	than	+95°F	(or	+35°C	).
•	 Keep	foliage	plants	and	pets	away	from	the	
projector. The temperature around the exhaust 
vents and that of the cabinet on the top of the 
exhaust vents become high. Take special care for 
small children.
Important:
•	 Do	not	apply	force	to	the	lens,	because	the	lens	
may be damaged.
•	 Be	sure	to	use	this	projector	at	an	altitude	of	less	
than 1500 meters.