Mitsubishi Fd630u Projector User Manual

EN-31
ENGLISH
Network settings (continued)
How to Use Network Function When connecting a computer and projector with LAN, config-
ure the both IP Addresses in the same network group.
If connecting in different network group, be sure to use a 
router. As for the settings of a router, ask the network adminis-
trator.
 Configure the IP CONFIG correctly. If the settings are not cor-
rect, the communication may be unavailable. For the detail, 
consult the network administrator.
 Depending on the settings...

EN-32
Advanced features
Setting of the image displayed during startup 
or muting
You can display your desired image as the startup screen (or splash 
screen). Using the menu, you can also use such image as a back-
ground that is displayed while the video is muted or no signal is sup-
plied.
Important: You can’t set IMAGE CAPTURE when PASSWORD FUNCTION in 
the FEATURE menu has been set to SPLASH ID SCREEN to 
enable the password lock.
 You can’t set IMAGE CAPTURE when the component video signal 
is...

EN-33
ENGLISH
Advanced features (continued)
 When you display 60-Hz and 50-Hz video signals at the 
same time, motion images may not be displayed properly. In 
this case, set VERT. SYNC of USER in the SIGNAL menu to 
OFF for the left screen. (See page 24.)
 When BACK COLOR of the INSTALLATION menu is set to 
IMAGE, you cannot use the split mode.
To change the input source of the left or right screen: To change the input source of the left screen, press the W button 
on the remote control.
 To change...

EN-34
Advanced features (continued)
Supervising and controlling by computerYou can supervise and control the projectors operation using a personal computer via a LAN network.
 To supervise and control the projector, install the software ProjectorView Global+ contained in the attached CD-ROM. For the installation pro-
cedure and usage of the software, see LAN Control Utility User Manual contained in the attached CD-ROM.
Major functions
ProjectorView Global+
Batch projector controlling / supervising...

EN-35
ENGLISH
Advanced features (continued)
An example of connecting the projector to peripherals 
 When using an external hub or router, use a Category 5 straight cable. (A crossed cable can be used with some hubs and routers. See the 
appropriate documentation for more information.)
 Dont touch the metal parts of the LAN connector and LAN cable because static electricity may be discharged from your body, causing damage 
to the projector.
Using the LAN Control Utility User ManualThe LAN Control...

EN-36
Lamp replacement
This projector is equipped with a lamp to project images. This lamp is 
a consumable. It may burn out or its brightness may decrease during 
use. In such cases, replace the lamp with a new one as soon as possi-
ble. Be sure to replace the lamp with a new lamp separately sold that 
is exclusive to this projector. Contact your dealer for purchase of the 
lamp.
Caution: Do not remove the lamp immediately after using the projector. You 
may get burned because the lamp is very hot...

EN-37
ENGLISH
Lamp replacement (continued)
4. Insert the two cutout portions (h) in the slit of the projector, paste 
the two taping portions (g) with the tape included in the Lamp 
Replacement Attachment, and then fix the Lamp Replacement 
Attachment to the projector.
5. Pull out the lamp unit (f) in the bag by the handle (e).
6. Remove the tape fixing the Lamp Replacement Attachment, and 
remove the Lamp Replacement Attachment with the lamp unit 
remaining in the bag.
(Caution)
 Pull the lamp unit out...

EN-38
Troubleshooting
Before asking for repair of the projector, check the following. If the symptom persists, stop using the projector, be sure to unplug the power plug, and 
then contact your dealer.
No image appears on the screen.
 
ProblemSolution
Power can not be turned on. Check whether the indicators are on or off and how they are lightning. 
No image appears on the screen. Cancel the AV mute by pressing the AV MUTE button.
 Check that the lens cap is removed.
 It may take about 1 minute for...

EN-39
ENGLISH
Troubleshooting (continued)
Images are not displayed correctly.
ProblemSolution
Projected images are shaking.
Projected images are displaced. Check that the cable connected to the external device isn’t intermittent.
 Connect the cable’s plug with the external device’s connector firmly.
 Press the AUTO POSITION button.
 Some computers output out-of-spec signals on rare occasion. Adjust the SIGNAL menu. (See page 28.)
Projected images are distorted.  Adjust the projector and the screen...

EN-40
Troubleshooting (continued)
Others
If the following problem occurs after the lamp is replaced, check the following first.
Maintenance 
Warning:Do not use flammable solvents (benzene, thinner, etc.) and flammable aerosols when cleaning the projector body and lens. Flammable substances 
may ignite causing fire or breakdown while the lamp is illuminating.
Caution: Be sure to turn off the lamp and unplug the power cord from the wall outlet before you perform any maintenance on the projector. 
Cleaning...