Mitsubishi Fd630u G Projector User Manual

							DLP PROJECTOR 
MODEL 
FD630U/FD630U-G
User Manual 
This User Manual is important to you. 
Please read it before using your projector. 
EN
ENGLISH 
						

							EN-2The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsu-
lated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric 
shock. 
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and 
maintenance (servicing) instructions in the literature accompanying the appliance. 
WARNING Use the attached specified power supply cord. If you use another 
power supply cord, it may cause interference with radio and television 
reception. 
This apparatus must be grounded. 
DO NOT LOOK DIRECTLY INTO THE LENS WHEN THE 
PROJECTOR IS IN THE POWER ON MODE. 
CAUTION Not for use in a computer room as defined in the Standard for the 
Protection of Electronic Computer/Data Processing Equipment, 
ANSI/NFPA 75. 
The attached power cord is to be used exclusively for this product. 
Never use it for other products.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.  
CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUT-
LET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.  
NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND 
SHALL BE EASILY ACCESSIBLE. 
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL. 
						

							EN-3
ENGLISH
Contents
Important safeguards................................................................................................................................ 4
Overview ................................................................................................................................................... 6
Remote control ..................................................................................................................................... 7, 8
Installation ................................................................................................................................................ 9
Basic connections................................................................................................................................... 11
Preparation ............................................................................................................................................. 14
Basic operation ....................................................................................................................................... 15
Menu operation ....................................................................................................................................... 18
Image adjustment ................................................................................................................................... 26
Network settings ..................................................................................................................................... 29
Advanced features .................................................................................................................................. 32
Lamp replacement .................................................................................................................................. 36
Troubleshooting ...................................................................................................................................... 38
Indicators ................................................................................................................................................ 41
Specifications ......................................................................................................................................... 42
Trademark, Registered trademark 
Macintosh is registered trademark of Apple Computer Inc.
DLPTM, Digital Micromirror Device, DMD, and BrilliantColorTM are all trademarks of Texas Instruments.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
Microsoft, Windows, Windows 2000, Windows XP, Windows Vista, and Internet Explorer are registered trademarks, trademarks, or trade names of 
Microsoft Corporation in the U.S. and/or other countries.
Other brand or product names are trademarks or registered trademarks of their respective holders.  
						

							EN-4
Important safeguards
Please read all these instructions regarding your projector and retain 
them for future reference. Follow all warnings and instructions marked 
on the projector. 
1. Read instructions 
All the safety and operating instructions should be read before 
the appliance is operated. 
2. Retain instructions 
The safety and operating instructions should be retained for 
future reference. 
3. Warnings 
All warnings on the appliance and in the operating instructions 
should be adhered to. 
4. Instructions
All operating instructions must be followed. 
5. Cleaning
Unplug this projector from the wall outlet before cleaning it. Do 
not use liquid aerosol cleaners. Use a damp soft cloth for clean-
ing. 
6. Attachments and equipment 
Never add any attachments and/or equipment without the 
approval of the manufacturer as such additions may result in the 
risk of fire, electric shock or other personal injury. 
7. Water and moisture 
Do not use this projector near water or in contact with water. 
8. Accessories
Do not place this projector on an unstable cart, stand, tripod, 
bracket or table. Use only with a cart, stand, tripod bracket, or 
table recommended by the manufacturer or sold with the projec-
tor. Any mounting of the appliance should follow the manufac-
turer’s instructions and should use a mounting accessory 
recommended by the manufacturer. 
An appliance and cart combination should be moved with care. 
Quick stops, excessive force and uneven surfaces may cause 
the appliance and cart combination to overturn. 
9. Ventilation 
Slots and openings in the cabinet are provided for ventilation, 
ensuring reliable operation of the projector and to protect it from 
overheating. Do not block these openings or allow them to be 
blocked by placing the projector on a bed, sofa, rug, or book-
case. Ensure that there is adequate ventilation and that the man-
ufacturer’s instructions have been adhered to. 
10. Power sources 
This projector should be operated only from the type of power 
source indicated on the marking label. If you are not sure of the 
type of power, please consult your appliance dealer or local 
power company. 
11. Power-cord protection 
Power-supply cords should be routed so that they are not likely 
to be walked on or pinched by items placed upon or against 
them. Pay particular attention to cords at plugs, convenience 
receptacles, and points where they exit from the appliance. Do 
not put the power cord under a carpet. 12. Overloading 
Do not overload wall outlets and extension cords as this can 
result in a fire or electric shock. 
13. Objects and liquids 
Never push objects of any kind through openings of this projec-
tor as they may touch dangerous voltage points or short-out 
parts that could result in a fire or electric shock. Never spill liquid 
of any kind on the projector. 
14. Servicing 
Do not attempt to service this projector yourself. Refer all servic-
ing to qualified service personnel. 
15. Damage requiring service 
Unplug this projector from the wall outlet and refer servicing to 
qualified service personnel under the following conditions: 
(a) If the power-supply cord or plug is damaged. 
(b) If liquid has been spilled, or objects have fallen into the pro-
jector. 
(c) If the projector does not operate normally after you follow 
the operating instructions. Adjust only those controls that 
are covered by the operating instructions. An improper 
adjustment of other controls may result in damage and may 
often require extensive work by a qualified technician to 
restore the projector to its normal operation. 
(d) If the projector has been exposed to rain or water. 
(e) If the projector has been dropped or the cabinet has been 
damaged. 
(f) If the projector exhibits a distinct change in performance - 
this indicates a need for service. 
16. Replacement parts 
When replacement parts are required, be sure that the service 
technician has used replacement parts specified by the manu-
facturer or parts having the same characteristics as the original 
part. Unauthorized substitutions may result in fire, electric shock 
or other hazards. 
17. Safety check 
Upon completion of any service or repair to this projector, ask 
the service technician to perform safety checks determining that 
the projector is in a safe operating condition.  
						

							EN-5
ENGLISH
WARNING: 
Unplug immediately if there is something wrong with 
your projector. 
Do not operate if smoke, strange noise or odor comes out of your pro-
jector. It may cause fire or electric shock. In this case, unplug immedi-
ately and contact your dealer. 
Never remove the cabinet. This projector contains high voltage circuitry. An inadvertent contact 
may result in an electric shock. Except as specifically explained in 
User Manual, do not attempt to service this product by yourself. 
Please contact your dealer when you want to fix, adjust, or inspect the 
projector. 
Do not modify the projector. It can lead to fire or electric shock. 
Do not keep using the damaged projector. If the projector is dropped and the cabinet is damaged, unplug the 
projector and contact your dealer for inspection. It may lead to fire if 
you keep using the damaged projector. 
Do not face the projection lens to the sun. It can lead to fire. 
Use correct voltage. If you use incorrect voltage, it can lead to fire. 
Do not place the projector on uneven surface. Place the projector on a level and stable surface only.  
Do not look into the lens when the projector is operating. It may hurt your eyes. Never let children look into the lens when the 
projector is on. 
Do not unplug the power cord during operation. It can lead to lamp breakage, fire, electric shock or other trouble. Wait 
for the fan to stop before unplugging the power cord. 
Do not touch the air outlet grilles and bottom plate. Do not touch them or put other equipment close to the air outlet grilles 
because they become hot during operation. The heated air outlet 
grilles and bottom plate may cause injury or damage to other equip-
ment. Also, do not put the projector on a desk that is easily affected by 
heat. 
Do not look into the air outlet grilles when projector is 
operating. 
Heat, dust, etc. may blow out of them and hurt your eyes. 
Do not block the air inlet and outlet grilles. If they are blocked, heat may be generated inside the projector, caus-
ing deterioration in the projector quality and fire. 
Do not use flammable solvents (benzene, thinner, etc.) 
and flammable aerosols near the projector.
Flammable substances may ignite causing fire or breakdown because 
the temperature inside the projector rises very high while the lamp is 
illuminating.
Do not use the projector with condensation on it.It can lead to breakdown or other failure.
Place of installation For safety’s sake, do not use the projector at any place subjected to 
high temperature and high humidity. Please maintain an operating 
temperature, humidity, and altitude as specified below. 
 Operating temperature: between +41°F (+5°C) and +95°F (+35°C) 
 Operating humidity: between 30% and 90% 
 Never put any heat-producing device under the projector to pre-
vent the projector from being overheated. 
 Do not install the projector at a place that is unstable or subject to 
vibration. 
 Do not install the projector near any equipment that produces a 
strong magnetic field. Also refrain from installing the projector near 
any cable carrying a large amount of current. 
 Place the projector on a solid, vibration-free surface. Otherwise it 
may fall, causing serious injury or damage. 
 Do not stand the projector on its end. It may fall, causing serious 
injury or damage. 
 Slanting the projector more than ±10° (right and left) or ±15° (front 
and rear) may cause trouble or explosion of the lamp. 
 Do not place the projector near air-conditioning unit, heater, or 
humidifier to avoid hot or moist air to the exhaust and ventilation 
hole of the projector.
 Be sure to use this projector at an altitude of less than 1500 
meters.
When removing the lamp from the ceiling-mounted 
projector
Be sure to use the lamp replacement attachment designed specifically 
for this projector when replacing the lamp with a new one. Lamp frag-
ments may fall from the inside if the lamp were broken. 
						

							EN-6
Overview
1FOCUS ring
2ZOOM ring
3 Control panel
4 Air inlet grille
5 Remote control sensor (Front)
6 Air outlet grille
7 Terminal board
8 Speaker
9 Adjustment feet
10 Lock bar
11 Lamp cover
Caution:Do not replace the lamp immediately after using the pro-
jector because the lamp would be extremely hot and it 
may cause burns.
Control panel
1 Power button
2 POWER indicator
3 MENU button
4 STATUS indicator
5 KEYSTONE/ENTER button
6 AUTO POSITION / S button
7 COMPUTER / W button
8T button
9 VIDEO/ X button
Important: While the menu or the screen for the keystone adjust-
ment or password entry is being displayed, the COM-
PUTER, VIDEO, and AUTO POSITION buttons 
function as the W, X, and S buttons respectively.
 While the menu is on the screen, the KEYSTONE but-
ton functions as the ENTER button.
Terminal board
1Power jack
2 COMPUTER IN terminal (1, 2) (Mini D-SUB 15-pin)
3 MONITOR OUT terminal (Mini D-SUB 15-pin)
4 Remote control sensor (Rear)
5 AUDIO IN-1 terminal (Mini jack)
6 AUDIO IN-2 terminal (Mini jack)
7 AUDIO OUT terminal (Mini jack)
8 S-VIDEO terminal
9 VIDEO terminal
10 SERIAL (RS-232C) terminal (Mini DIN)
11 Kensington Lock
12 LAN terminal (RJ-45)
13 AUDIO IN-3 terminals (L/R)
14 HDMI terminal (HDMI 19-pin)
Kensington LockThis projector has a Kensington Security Standard connector for use with Kensington MicroSaver Security System.
Refer to the information that came with the Kensington System for instructions on how to use it to secure the projector. Please contact Kensington 
Technology Group below.
Kensington Technology Group
2855 Campus Drive
San Mateo, CA 94403, U.S.A.
Phone: +1- (650)572-2700 Fax: +1- (650)572-9675
11
9851234
10
7
6
642
89
531 7
4510 13 28314
71
611912 
						

							EN-7
ENGLISH
Overview (continued)
Bottom side
1 Adjustment feet
Remote control
1ON button
2 MAGNIFY button
3 VOLUME UP, DOWN buttons
4 KEYSTONE button
5 MENU button
Two types of MENU display are equipped. QUICK 
MENU appears on the screen when pressing MENU 
button. In addition, DETAIL MENU appears when 
selecting DETAIL MENU in this MENU and pressing 
ENTER button.
6ENTER button
7 AV (Audio/Video) MUTE button
8 OFF button
9 ASPECT button
10 AUTO POSITION button
11 Direction buttons
12 FREEZE button
13 VIDEO, S-VIDEO buttons
14 COMPUTER (1, 2) buttons
15 HDMI button
 The UP and DOWN buttons are used in the KEY-
STONE adjustment in addition to the volume control.
1
ON
ASPECT MAGNIFY
KEYSTONEVOL PAGE
UP
DOWN
MENU
FREEZE AUTO
POSITION
AV
MUTEENTER
1
2COMPUTERVIDEOVIEWER
UNPLUGS-VIDEO
WIRELESS DVI HDMI
STANDBY
1
2
3
4
5
6
78
9
13
14 10
11
12
15
This model does not 
have these functions.This model does not 
have these functions. 
						

							EN-8
Remote control
Battery installationUse two (AA, R6) size batteries.
1. Remove the back cover of the remote control by pushing the battery compartment door in the direction of the arrow.
2. Load the batteries making sure that they are positioned correctly (+ to +, and - to -).
 Load the batteries from - spring side, and make sure to set them tightly.
3. Replace the back cover.
Caution: Use of a battery of wrong type may cause explosion.
 Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.
 Dispose of used batteries according to your local regulations.
 Batteries may explode if misused. Do not recharge, disassemble, or dispose of in fire.
 Be sure to handle the battery according to the instructions.
 Load the battery with its positive (+) and negative (-) sides correctly oriented as indicated on the remote control.
 Keep batteries out of reach of children and pets.
 Remove the battery, if the remote control is not used for a long time.
 Do not combine a new battery with an old one.
 If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in contact with your eyes, rinse them 
with water and then consult your doctor.
Operation range (of the remote control)The maximum operation distance of the remote control is about 10 m (or about 32 feet) when the remote control is pointed at the remote control 
sensor of the projector. When the remote control is pointed to the screen, the distance from the remote control to the projector via the screen should 
be 5 m or less. However, the operation distance varies depending on the type of the screen used.
Important: Do not expose the remote control sensor to direct sunlight or fluorescent. Keep a distance at least 2 m (6.5 feet) between the remote control sen-
sor and the fluorescent light to ensure correct operation of the remote control.
Inverted fluorescent light, if located near the projector, may interfere the remote control.
 When you use the remote control too close to the remote control sensor, the remote control may not work correctly.
Reception angle (horizontal) Reception angle (vertical), ceiling mount Reception angle (vertical) 
						

							EN-9
ENGLISH
Installation
Layout of the projectorImage size varies depending on the distance between the screen and the projector.
Front projection
 The above figures are approximate and may be slightly different from the actual measurements.
When the aspect ratio of the screen is 4:3When the aspect ratio of the screen is 4:3, the positional relation between the pro-
jected image and the screen is as shown on the right. Refer to the following table 
for installation.
When the aspect ratio of the image is 16:9
 The above figures are approximate and may be slightly different from the actual measurements.
Screen Distance from the screen : L
Hd
Diagonal size Width : SW Height : SH Shortest (WIDE) Longest (TELE)
inch cm inch cm inch cm inch m inch m inch cm
4010235892050 47 1.2 71 1.8 6.617
60 152 52 133 29 75 71 1.8 107 2.7 9.9 25
80 203 70 177 39 100 96 2.4 144 3.6 13.2 34
100 254 87 221 49 125 120 3.1 180 4.6 16.5 42
150 381 131 332 74 187 182 4.6 271 6.9 24.7 63
200 508 174 443 98 249 243 6.2 362 9.2 33.0 84
250 635 218 553 123 311 304 7.7 453 11.5 41.2 105
300 762 261 664 147 374 365 9.3 - - 49.5 126
Screen Size Size of Projected Image Projected Distance : L
Hd
4:3 Diagonal 
SizeWidth : SW Height : SH16:9
Diagonal SizeWidth : W Height : HBlank Space : 
BShortest 
(Wide)Longest 
(Tele)
inch cm inch cm inch cm inch cm inch cminch cm inch cm inch m inch m inch cm
40102328124613793328118463.0 8 431.1651.66.115
60 152 48 122 36 91 55 140 48 122 27 69 4.5 11 65 1.7 98 2.5 9.1 23
80 203 64 163 48 122 73 187 64 163 36 91 6.0 15 88 2.2 132 3.3 12.1 31
100 254 80 203 60 152 92 233 80 203 45 114 7.5 19 110 2.8 165 4.2 15.1 38
150 381 120 305 90 229 138 350 120 305 68 171 11.3 29 166 4.2 249 6.3 22.7 58
200 508 160 406 120 305 184 466 160 406 90 229 15.0 38 223 5.7 332 8.4 30.3 77
250 635 200 508 150 381 229 583 200 508 113 286 18.8 48 279 7.1 416 10.6 37.8 96
300 762 240 610 180 457 275 699 240 610 135 343 22.5 57 335 8.5 - - 45.4 115
SH
SW
L : Between the screen and the front edge of the projector
Hd : Height of the projected image
SW=W
H SH
B B
Screen size 
						

							EN-10
Installation (continued)
Front projection, ceiling mountingFor ceiling mounting, you need the ceiling mount kit designed for this 
projector. Ask a specialist for installation.
For details, consult your dealer.

The warranty on this projector does not cover any damage caused 
by use of any non-recommended ceiling mount kit or installation of 
the ceiling mount kit in an improper location
.
 When using the projector mounted on the ceiling, set IMAGE 
REVERSE in the INSTALLATION menu to MIRROR INVERT. See 
page 22.
 When the projector is mounted on the ceiling, images may appear 
darker than those projected in the case of tabletop mounting. This 
isn’t a product malfunction.
Ceiling Mount InstallationIf you wish to install the projector using a ceiling mount, please use 
the screw holes as the illustration shows.
Important: Screws are not included. Please obtain the appropriate screws for 
your type of ceiling. (M4 diameter)
 It is recommended that you keep a reasonable space between the 
bracket and the projector to allow for proper heat distribution.
Rear projectionAsk a specialist for installation. For details, consult your dealer.
 For rear projection, set IMAGE REVERSE in the INSTALLATION 
menu to MIRROR. See page 22.
Caution: Placing the projector directly on a carpet impairs ventilation by the 
fans, causing damage or failure. Put a hard board under the pro-
jector to facilitate ventilation.
 Place the projector at least 50 cm (or 20 inches) away from the 
wall to prevent the air inlet grille and the air outlet grilles that emit 
hot air from being blocked.
 Do not use the projector in the following locations and manners, 
which may cause fire or electric shock.
 In a dusty or humid place.
 In a sideways or upside-down position.
 Near a heater.
 In an oily, smoky, or damp place such as a kitchen.
 In direct sunlight.
 Where the temperature rises high, such as in a closed car.
 Where the temperature is lower than +41°F (or +5°C) or higher 
than +95°F (or +35°C ).
Important: Do not apply force to the lens, because the lens may be damaged.
 Be sure to use this projector at an altitude of less than 1500 
meters.