Mitsubishi Ex241u Projector User Manual

EN-31
ENGLISH
Setting the presentation timer
The presentation timer can indicate the presentation time on the screen to help 
you achieve better time management when giving presentations. Follow these 
steps to utilize this function:
1. Press TIMER SET UP on the remote control or go to the SYSTEM 
SETUP: Basic > Presentation Timer menu and press MODE/ENTER to 
display the Presentation Timer page.
2. Press   to highlight Timer period and decide the timer period by 
pressing  / . The length of time can be...

EN-32
Hiding the image
In order to draw the audiences full attention to the presenter, you can use 
BLANK on the projector or remote control to hide the screen image. Press any 
key on the projector or remote control to restore the image. The word BLANK 
appears at the lower right corner of the screen while the image is hidden.
You can set the blank time in the SYSTEM SETUP: Basic > Blank Timer 
menu to let the projector return the image automatically after a period of time 
when there is no action taken...

EN-33
ENGLISH
1. Repeat steps 1-2 above.
2. Press   to highlight Volume and press  /  to select a desired sound level.
Standby Audio Out
Selecting On enables the function. The projector can output an Audio input signal when it is in standby mode and 
Audio input and Audio out jack is correctly connected to devices.
When the projector enters standby mode, the audio will be interrupted briefly. This is not a product malfunction.
Personalizing the projector menu display
The On-Screen Display (OSD) menus can...

EN-34
3D
Watching 3D Content
You can enjoy 3D Content with this projector.
In order to watch 3D Content, you need to have the following items:
1. Field-sequential 3D video contents
2. DLP Link active electronic shutter glasses
(Field-sequential: The system which displays alternately the image for the left eye and the right eye.)
Play the field-sequential 3D video contents on a computer or DVD player, and then, connect the cable with the 
projector.
Go to the DISPLAY menu, then, set the 3D option to On....

EN-35
ENGLISH
• 3D image may not appear on the screen depending on the PC performance such as graphics board, memory, or CPU.
• The signals in the below table can be displayed with viewing 3D Contents on the projector. If a different signal is fed, the 
projector shows no 3D contents even with the 3D option set to On in the DISPLAY menu.
• If DVD is run by 480p signals, 3D image may not be displayed correctly depending on the DVD player.
• If 3D image is projected on the screen in 120Hz, the image may...

EN-36
Supervising and controlling by computer
With a proper LAN cable connection and LAN Control settings, you can operate the projector from a computer using 
a web browser or PJLink™ application (EX321U only) when the computer and the projector are connected to the 
same local area network.
This projector supports Crestron® software and PJLink™ (EX321U).
An example of connecting the projector to computer.
• When using an external hub or router, use a Category 5 straight cable. (A crossed cable can be...

EN-37
ENGLISH
Controlling the projector remotely through a web browser 
(e-Control™)
Once you have the correct IP address for the projector and the projector is on or in standby state, you can use any 
computer that is on the same local area network to control the projector.
When using this function, Adobe Flash Player has to be installed in your computer. Please download Adobe Flash 
Player from the website of Adobe Systems Incorporated.
1. Enter the IP address of the projector in the address bar of...

EN-38
iv. Once set, access to the remote network operation page on this projector has been password-protected. 
To enable this function, check the box in front of Enable and type in your desired password in the 
New Password column and confirm the new password by re-entering the new password at the Confirm 
column. To disable password protection, uncheck the box.
v. Once set, access to the Tools page has been password-protected. Refer to step iv for how to use the 
password function.
• After making the...

EN-39
ENGLISH
About PJLink™
• To use PJLink™ function, the PJLink™ application software is required.
• For the specifications of PJLink™, access to the Web site of Japan Business Machine and Information System 
Industries Association (JBMIA). (http://pjlink.jbmia.or.jp/english)
• This projector is fully compliant to the specifications of JBMIA PJLink™ Class 1. It supports all the commands 
defined by PJLink™ Class 1, and the compliance has been verified with the PJLink™ standard specifications 
Version...

EN-40
• The PJLink INPT? will be replied only when the source is displayed on screen. When there is no signal, only 
Unavailable Time! will be answered.
• The above-mentioned control may not be performed correctly or the monitoring data may not be obtained correctly in the 
following conditions:
• During standby
• During input source switching
• During command processing
• During AUTO execution
• Before the splash screen disappears after the power is turned on.
• Use 1 computer to control/monitor 1...