Mitsubishi Ex100u Projector User Manual

 EN - 11
ENGLISH
Projector + Computer
For computer with Mini D-SUB
Important:
•  When you use a longer RGB cable instead of the provided cable, the image may not be projected correctly. 
•  Some computers require additional connectors or analog RGB output adapters to be connected with this projector. 
Contact your dealer for further information. 
•  This projector uses stereo pin jack for its audio input. Check the type of the audio output terminal of the connected 
computer and prepare a proper cable...

EN - 12
Preparation
1.  Tilt up the project to the appropriate angle. 
2.  Press the foot adjustment buttons next to the adjust-
ment feet (rear), and the adjustment feet will come 
out. 
3.  Release the buttons to lock the adjustment feet (rear) 
to that position.
4.  Rotate the adjustment feet (rear) for fi ne adjustment.
After using the projector:
5.  Put the adjustment feet (rear) back into the projector 
by pressing the foot adjustment buttons.
Important: 
•  If necessary, rotate the adjustment feet...

 EN - 13
ENGLISH
Basic operation
•  The projector starts warming up when the POWER 
button is pressed. During the warm-up process, 
images may appear dark and no commands are ac-
cepted.
•  By blinking red, the STATUS indicator indicates that 
the lamp should be replaced soon. Replace the lamp 
when the STATUS indicator blinks red. (See page 23 
and 26.) 
•  Images may not be projected with good quality in 
an extremely hot or cold environment. (This is not a 
product malfunction.) 
4.  Adjust the focus...

EN - 14
VOLUME     10
Volume from the speaker
Press the VOLUME + or - button to change the volume 
from the speaker.
The volume control bar will appear on the screen.
•  The volume control bar will disappear about 10 sec-
onds after the VOLUME button is released.
•  The VOLUME buttons dont function while the menu 
selection bar or the menu is being displayed. 
•  When a high-level audio signal, such as a DVD audio 
signal, is supplied to the AUDIO IN terminal, the out-
put from the speaker may be...

EN - 15
ENGLISH
Menu operation
IMAGE
XGA60opt.
INSTALLATION
opt.XGA60
INSTALLATION
opt.
AUTO POWER 
ON
AUTO POWER 
OFF
OFF OFF
XGA60
AUTO POWER 
ON
AUTO POWER 
OFF
OFF OFF
AUTO POWER 
ON
AUTO POWER 
OFF
30 minOFF
Basic operation
Several settings can be adjusted using the menu. 
Example : Auto power off time setting 
1.  Press the MENU button.
2.  Press the  or  button to select INSTALLATION.
3.  Press the ENTER button (or  button).4.  Press the 
 or  button to select AUTO POWER 
OFF. 
5.  Press the ...

EN - 16
Menu operation (continued)
INSTALLATION
opt.
ON
BACK COLOR AUTO POWER 
ON
AUTO POWER 
OFF
SPLASH 
SCREEN
LAMP MODEON
BLUEOFF OFF
STANDARD
OFF IMAGE 
REVERSE
XGA60
CONTRAST
IMAGE
0
BRIGHTNESS 0
STANDARD
0
COLOR
AUTO0
XGA60
CineRichColor AUTO
OFF
TINT
0SHARPNESS
COLOR TEMP.
GAMMA MODE sRGB
opt.
1 IMAGE
CONTRAST ............................ Use to adjust the image contrast. The contrast 
becomes higher as the value increases.
BRIGHTNESS ......................... Use to adjust the image brightness....

EN - 17
ENGLISH
3 FEATURE
MENU POSITION ................... Use to select the position of the menu on the 
screen,  1. 
 (upper left) or 2.  (lower right).
CINEMA MODE ...................... When AUTO is selected, the fi lm mode will be 
automatically activated when a fi lm source signal 
is inputted. When OFF is selected, the fi lm mode 
will not be activated. 
VIDEO SIGNAL ....................... When AUTO is selected, the appropriate video 
format is automatically selected depending on the 
input signal....

EN - 18
Image adjustment
CONTRAST R
USER
0
CONTRAST B 0
BRIGHTNESS R 0
BRIGHTNESS B 0
CONTRAST
IMAGE
0
BRIGHTNESS 0
STANDARD
0
COLOR
AUTO0
XGA60
CineRichColor AUTO
OFF
TINT
0SHARPNESS
COLOR TEMP.
GAMMA MODE sRGB
opt.
Color temperature
1.  Select COLOR TEMP. in the IMAGE menu. 
2.  Press the  or  button to select USER 
. 
3.  Press the ENTER button.
4.  Press the 
 or  button to select the desired item. 
5.  Press the  or  button to adjust the selected item. 
6.  Repeat steps 4 and 5 for optimum...

EN - 19
ENGLISH
Adjustment of the image from the computer
This projector adjusts the format of the video signal 
supplied from the computer. However, sometimes im-
ages are not projected correctly owing to the type of 
the computer used. When the image from the computer 
isnt projected correctly, press the AUTO POSITION 
button. (See page 14.) If the image isnt projected cor-
rectly yet, adjust the image from the computer using the 
menu.  
To move the image horizontally :
Adjust HORIZ. POSITION in the...

EN - 20
Advanced features
Still
To stop the motion in the image temporarily (or to dis-
play a still image):
Press the STILL button on the remote control.
•  The image will freeze temporarily.
To resume the motion in the image:
Press the STILL button on the remote control again.
Important:
•  Do not display a still picture for a long time because 
the afterimages may persist on the screen.
Page-up and page-down
You can control the computer to page-up and page-
down the presentation data using the remote...