Mitsubishi Ew330u Projector User Manual
Have a look at the manual Mitsubishi Ew330u Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 561 Mitsubishi manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
EN-51 ENGLISH Replacing the lampSpare lamp for EX320U/EW330U: VLT-EX320LP • Be sure to replace the lamp with a new lamp separately sold that is exclusive to this projector. Contact your dealer for purchase of the lamp. • To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before changing the lamp. • To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp. • To reduce the risk of injuries to fingers and damage to internal components, use caution when removing lamp glass that has shattered into sharp pieces. To reduce the risk of injuries to fingers and/or compromising image quality by touching the lens, do not touch the empty lamp compartment when the lamp is removed. • Be sure to install the lamp securely. When the lamp isn’t installed properly, it won’t illuminate. Improper installation may also result in fire. • If the lamp should break, never shake the lamp box or hold it in front of your face after removing it. The glass fragments may fall out and cause injury to your eyes. • In the event that the high-pressure mercury lamp exploded, glass fragments may have been scattered inside the projector. Ask your dealer to replace the lamp and to inspect the inside of the projector. When you clean or replace the lamp by yourself, be sure to hold the handle of the lamp. You may get injured by glass fragments. • Contact your dealer when replacing the lamp unit with the projector mounted to the ceiling. • Don’t remove the lamp for any purpose other than replacement. Unnecessary removal of the lamp may result in a breakdown. • This projector uses a high-pressure mercury lamp as the light source. The high-pressure mercury lamp may explode or fail to illuminate permanently because of an impact, scratch, or deterioration through use. The period of time until explosion or permanent failure to illuminate varies considerably from lamp to lamp, depending on operation conditions. Therefore, the lamp may explode soon after the start of use. • The possibility of explosion of the lamp increases if you use it beyond its replacement period. When the instruction of lamp replacement appears, replace it with a new one immediately even if the lamp is still lighting normally. • When the high-pressure mercury lamp explodes, glass fragments will scatter inside or outside the lamp box and the gas charged inside the lamp will diffuse inside or outside the projector. The gas inside the lamp contains mercury. Be careful not to breathe it or avoid it from entering your eye or mouth. If you should breathe it or if it should enter your eye or mouth, see a doctor immediately. • This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a proper manner. • Be sure to use the lamp dedicated to this projector, VLT-EX320LP for EX320U/EW330U. Use of other lamps may cause a failure of the projector. 1. Turn the power off and disconnect the projector from the wall socket. If the lamp is hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled. 2. Unscrew the screws on the lamp cover. 3. Remove the lamp cover from the projector. , Pull up the lamp cover, pussing up the allow parts of the front panel. • Do not turn the power on with the lamp cover removed. • Do not insert your fingers between the lamp and the projector. The sharp edges inside the projector may cause injuries. 4. Remove and dispose of the lamp protection film. 5. Loosen the screw that secures the lamp. 12 3 1 22 3 2 1
EN-52 13. Restart the projector. Do not turn the power on with the lamp cover removed. Resetting the lamp timer 14. After the startup logo, open the On-Screen Display (OSD) menu. Go to the SYSTEM SETUP: Advanced > Lamp Settings menu. Press MODE/ENTER. The Lamp Settings page is displayed. Press to highlight Reset lamp timer and press MODE/ENTER. A warning message is displayed asking if you want to reset the lamp timer. Highlight Reset and press MODE/ENTER. The lamp time will be reset to 0. 6. Lift the handle so that it stands up. Use the handle to slowly pull the lamp out of the projector. • Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector. • Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials. • Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images. 7. As shown in the figure, lower the new lamp into the lamp compartment while aligning the lamp with the holes in the lamp compartment. Make sure it fits in the projector. 8. Tighten the screw that secures the lamp. • Loose screw may cause a bad connection, which could result in malfunction. • Do not over tighten the screw. 9. Ensure the handle is fully laid flat and locked in place. 10. Place the lamp protection film supplied with the new lamp on the lamp compartment. 11. As shown in the figure, replace the lamp cover on the projector. 12. Tighten the screws that secure the lamp cover. • Loose screw may cause a bad connection, which could result in malfunction. • Do not over tighten the screws. 2 1 2 1
EN-53 ENGLISH • Do not reset if the lamp is not new or replaced as this could cause damage. • This projector uses a lamp that contains mercury. Disposal of the lamp or the projector with the lamp may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org. (For US only).
EN-54 Indicators LightStatus & Description PowerTe m pLamp Power events Orange Off OffStand-by mode Green FlashingOff OffPowering up Green Off OffNormal operation Orange FlashingOff Red• The projector needs 90 seconds to cool down as it was abnormally shut down without the normal cooling down process. • The projector needs to cool for 90 seconds after the power is turned off. Orange FlashingOff OffCooling down. Lamp events Orange FlashingOff RedThe projector has shutdown automatically. If you try to re-start the projector, it will shutdown again. Please contact your dealer for assistance. Off Off Red• The projector needs 90 seconds to cool down. • Please contact your dealer for assistance. Thermal events Off Red Off The projector has cooling down automatically. If you try to re-start the projector, it will shut down again. Please contact your dealer for assistance. Off Red Red Off Red Green Red Red Red Red Red Green Green Red Red Green Red Green Orange Red Red Orange Red Green Off Green Red Off Green Green
EN-55 ENGLISH Troubleshooting The projector does not turn on. No picture Blurred image Remote control does not work The password is incorrect The LAN function cannot be used CauseRemedy There is no power from the power cable.Plug the power cord into the AC inlet on the projector, and plug the power cord into the power outlet. If the power outlet has a switch, make sure that it is switched on. Attempting to turn the projector on again during the cooling process.Wait until the cooling down process has completed. CauseRemedy The video source is not turned on or connected correctly.Turn the video source on and check that the signal cable is connected correctly. The projector is not correctly connected to the input signal device.Check the connection. The input signal has not been correctly selected.Select the correct input signal with the SOURCE key on the projector or remote control. The lens cover is still closed. Open the lens cover. CauseRemedy The projection lens is not correctly focused. Adjust the focus of the lens using the focus ring. The projector and the screen are not aligned properly.Adjust the projection angle and direction as well as the height of the unit if necessary. The lens cover is still closed. Open the lens cover. CauseRemedy The battery is out of power. Replace the battery with a new one. There is an obstacle between the remote control and the projector.Remove the obstacle. You are too far away from the projector. Stand within 8 meters (26 feet) of the projector. CauseRemedy You do not remember the password.Please see Entering the password recall procedure on page 23 for details. CauseRemedy LAN control settings or LAN cable connection are problematic.Verify the LAN control settings. Please see Configuring the LAN Control Settings on page 37 for details. Make sure the LAN cables are properly connected. The web page is not shown in the web browser or the web page is not responding.Reload the page to see the data after changing on the screen. If the page is not showing the modified data, check the IP address of projector and log-in again.
EN-56
Specifications
Projector specifications
All specifications are subject to change without notice.
General
Product nameDLP™ Projector
Model name EX320UEW330U
Optical
Resolution 1024 x 768 XGA 1280 x 800 WXGA
Display system 1-CHIP DMD
Lens F/Number F = 2.6 to 2.9, f = 16.8 to 21.8 mm
Lamp 230 W lamp
Electrical
Power supplyAC100–240V, 50/60 Hz (Automatic)
Power consumption 3.3 A, 330 W (Max), < 1 W (Standby) When setting is:
Standby Monitor Out: Off
Standby Audio Out:Off
LAN Control Settings: Off
Mechanical
Dimensions 282 mm (W) x 92 mm (H) x 229 mm (D) (Not including protrusion)
Weight 2.5 Kg (5.5 lbs)
Input terminal
Computer input
RGB input D-Sub 15-pin (female) x 2
Video signal input
S-VIDEO Mini DIN 4-pin port x 1
VIDEO RCA jack x 1
SD/HDTV signal input Analog – D-Sub Component RCA jack x 3
(through RGB input)
Digital – HDMI
Audio signal input PC audio jack x 1 (Share the terminal with computer and video inputs)
Output terminal
RGB output D-Sub 15-pin (female) x 1
Audio signal output PC audio jack x 1 (Share the terminal with computer and video inputs)
Speaker output 2W x 1
Control terminal
Serial control D-Sub 9-pin (Male) x 1
LAN control RJ-45 x 1
Environmental requirements
Operating temperature 0°C–40°C (without condensation)
Operating relative humidity 10%–90% (without condensation)
EN-57 ENGLISH Dimensions 282 mm (W) x 92 mm (H) x 229 mm (D) (Not including protrusion) Timing chart Supported timing for PC input * The projector only supports the timing (720 x 400) with 5 lines (R, G, B, H, V). * EX320U dose not support the timing of WXGA_120. 282 233 110 50 68.3 To l e r a n c e : ± 2 m m 229 92 Resolution ModeVertical Frequency (Hz)Horizontal Frequency (kHz)Clock (MHz) *720 x 400 720 x 400_70 70.087 31.469 28.3221 640 x 480VGA_60 59.940 31.469 25.175 VGA_72 72.809 37.861 31.500 VGA_75 75.000 37.500 31.500 VGA_85 85.008 43.269 36.000 VGA_120 119.518 61.910 52.500 800 x 600SVGA_60 60.317 37.879 40.000 SVGA_72 72.188 48.077 50.000 SVGA_75 75.000 46.875 49.500 SVGA_85 85.061 53.674 56.250 SVGA_120 119.854 77.425 83.000 SVGA_120 119.972 76.302 73.250 1024 x 768XGA_60 60.004 48.363 65.000 XGA_70 70.069 56.476 75.000 XGA_75 75.029 60.023 78.750 XGA_85 84.997 68.667 94.500 XGA_120 119.804 98.958 137.750 1280 x 800WXGA_60 59.81 49.702 83.500 WXGA_120 119.9 101.562 146.250 1280 x 1024SXGA_60 60.020 63.981 108.000 SXGA_75 75.025 79.976 135.000 SXGA_85 85.024 91.146 157.500 1280 x 9601280 x 960_60 60.000 60.000 108 1280 x 960_85 85.002 85.938 148.500 1440 x 900 WXGA+_60 59.887 55.935 106.500 1400 x 1050 SXGA+_60 59.978 65.317 121.750 1600 x 1200 UXGA 60.000 75.000 162.000 640 x 480@67Hz MAC13 66.667 35.000 30.240 832 x 624@75Hz MAC16 74.546 49.722 57.280 1024 x 768@75Hz MAC19 75.020 60.241 80.000 1152 x 870@75Hz MAC21 75.06 68.68 100.00 *
EN-58 Supported timing for HDMI (HDCP) input * EX320U dose not support the timing of WXGA_120. Resolution ModeVertical Frequency (Hz)Horizontal Frequency (kHz)Clock (MHz) 720 x 400 720x400_70 70.087 31.469 28.3221 640 x 480VGA_60 59.940 31.469 25.175 VGA_72 72.809 37.861 31.500 VGA_75 75.000 37.500 31.500 VGA_85 85.008 43.269 36.000 VGA_120 119.518 61.910 52.500 800 x 600SVGA_60 60.317 37.879 40.000 SVGA_72 72.188 48.077 50.000 SVGA_75 75.000 46.875 49.500 SVGA_85 85.061 53.674 56.250 SVGA_120 119.854 77.425 83.000 SVGA_120 119.972 76.302 73.250 1024 x 768XGA_60 60.004 48.363 65.000 XGA_70 70.069 56.476 75.000 XGA_75 75.029 60.023 78.750 XGA_85 84.997 68.667 94.500 XGA_120 119.804 98.958 137.750 1280 x 800WXGA_60 59.81 49.702 83.500 WXGA_120 119.9 101.562 146.250 1280 x 1024SXGA_60 60.020 63.981 108.000 SXGA_75 75.025 79.976 135.000 1280 x 9601280 x 960_60 60.000 60.000 108 1280 x 960_85 85.002 85.938 148.500 1440 x 900 WXGA+_60 59.887 55.935 106.500 1400X1050 SXGA+_60 59.978 65.317 121.750 1600 x 1200 UXGA 60.000 75.000 162.000 VIDEO (HDCP)480p 60 31.47 27 576p 50 31.25 27.000 720p_60 60 45.00 74.25 720p_50 50 37.50 74.25 1080i_60 60 33.75 74.25 1080i_50 50 28.13 74.25 1080p 60 67.5 148.5 1080p 50 56.25 148.5 *
EN-59 ENGLISH Supported timing for Component-YPbPr input Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image vibration. Supported timing for Video and S-Video inputs What’s included in the box Replacement part Signal FormatHorizontal Frequency (kHz) Vertical Frequency (Hz) 480i(525i)@60Hz 15.7359.94 480p(525p)@60Hz 31.4759.94 576i(625i)@50Hz 15.6350.00 576p(625p)@50Hz 31.2550.00 720p(750p)@60Hz 45.0060.00 720p(750p)@50Hz 37.5050.00 1080i(1125i)@60Hz 33.7560.00 1080i(1125i)@50Hz 28.1350.00 1080P@60Hz 67.560.00 1080P@50Hz 56.2650.00 Video modeHorizontal Frequency (kHz) Vertical Frequency (Hz) Color sub-carrier Frequency (MHz) NTSC 15.73 603.58 PAL 15.63 504.43 SECAM 15.63504.25 or 4.41 PAL-M 15.73603.58 PAL-N 15.63503.58 PAL-60 15.73604.43 NTSC4.43 15.73604.43 AC power cord for US 2G.01111.001 for EU 2G.05921.011 for UK/SG 2G.03132.001 for AU 2G.01343.001 for KR 2G.05921.011 for AR 2G.03947.011 1 Remote control with battery 1 Safety manual/Quick start up 1CD-ROM 1 Soft carrying case 1 RGB cable 5K.08006.501 (Option / Not included in the box)Power cord is provided appropriately to the place of destination. Spare lamp: VLT-EX320LP
EN-44 Mitsubishi Projector Warranty, Sales Support and Service Information North America MDEA (Mitsubishi Digital Electronics America, Inc.) Presentation Products Division 9351 Jeronimo Road Irvine CA 92618, USA For Warranty Registration, visit: http://www.mitsubishi-presentations.com under Customer Care Sales & Inquiries Phone :Toll Free (888)307-0349 E-mail :[email protected] Technical Inquiries Phone :Toll Free (888)307-0309 E-mail :[email protected] MESCA (Mitsubishi Electric Sales Canada Inc.) http://www.mitsubishielectric.ca Information Technologies Group, 4299 14th Avenue, Markham, Ontario L3R 0J2, Canada Sales & Technical Inquiries Phone :+1-(800) 450-6487 Fax :+1-(905) 475-7958 E-mail :[email protected] Customer Care E-mail :[email protected] Europe MEU-FRA (Mitsubishi Electric Europe B.V French Branch) 25, Boulevard des Bouvets 92 741, Nanterre CEDEX, France Sales Inquiries Phone :+33 (0)1 55-68-55-53 Fax :+33 (0)1 55-68-57-31 Technical Inquiries Phone :+33 (0)1 55-68-56-42 Fax :+33 (0)1 55-68-57-31 MEU-GER (Mitsubishi Electric Europe B.V. German Branch) http://www.mitsubishi-evs.de/ Gothaer Strasse 8, 40880 Ratingen, Germany Sales Inquiries Phone :0049 - 2102 - 486 9250 Fax :0049 - 2102 - 486 7320 Technical Inquiries Phone :0049 - 2102 - 486 1330 Fax :0049 - 2102 - 486 1340 MEU-IR (Mitsubishi Electric Europe B.V. Irish Branch) http://www.mitsubishi.ie/ Westgate Business Park, Ballymount, Dublin 24, Ireland Sales Inquiries Phone :+353-1-4198807 Fax :+353-1-4198890 Technical Inquiries Phone :+353-1-4198808 Fax :+353-1-4198895 MEU-IT (Mitsubishi Electric Europe B.V. Italian Branch) Centro Direzionale Colleoni, Palazzo Sirio, Viale Colleoni 7, 20041 Agrate Brianza, Italy Sales & Technical Inquiries Phone :+39-(0)39-60531 Fax :+39-(0)39-6053214 E-mail :[email protected] MEU-NL (Mitsubishi Electric Europe B.V. Benelux Branch) http://www.mitsubishi.nl/LCD/ProdFrame.html Nijverheidsweg 23A, 3641 RP Mijdrecht, The Netherlands Sales Inquiries Phone :+31-297-282461 Fax :+31-297-283936 E-mail :[email protected] Technical Inquiries Phone :+31-297-282461 Fax :+31-297-283936 E-mail :[email protected] Russia (Mitsubishi Electric Europe B.V Moscow Representative Office) http://www.mitsubishi-projector.ru/ Moscow Representative Office, 52/5 Kosmodamianskaya Nab., 115054, Moscow, Russia Sales & Technical Inquiries Phone :(7095) 721-2068 Fax :(7095) 721-2071MEU-SP (Mitsubishi Electric Europe B.V. Spanish Branch) http://www.mitsubishielectric.es/ Ctra. de Rubi, 76-80, 08173 Sant Cugat del Valles, Barcelona, Spain Sales Inquiries Phone :+34-93.565.31.54 Fax :+34-93.589.43.88 E-mail :[email protected] Technical Inquiries Phone :+34-93.586.27.51 Fax :+34-93.588.53.87 E-mail :[email protected] MEU-SWE (Mitsubishi Electric Europe B.V Scandinavian Branch) Hammarbacken 14, Box 750, S-19127, Sollentuna, Sweden Sales Inquiries Phone :+46-(0)8-6251070 Fax :+46-(0)8-6251036 Technical Inquiries Phone :+46-(0)8-6251052 Fax :+46-(0)8-6251036 MEU-UK (Mitsubishi Electric Europe) http://www.mitsubishi.co.uk/evs/ Visual Information Systems Division, Travellers Lane, Hatfield, Hertfordshire, AL10 8XB U.K. Sales Inquiries Phone :+44 (1707) 278684 Fax :+44 (1707) 278541 E-mail :[email protected] Technical Inquiries Phone :+44 (870) 606 5008 Fax :+44 (1506) 431927 E-mail :[email protected] Asia CHINA (Mitsubishi Electric Air-Conditioning & Visual Information Systems (Shanghai) Ltd.) 12/F., Hong Kong New World Tower, 300 Huaihai Middle Road, Shanghai, 200021, China Sales Inquiries Phone :+86(21) 6335-3030 (Ext.3007) Fax :+86(21) 6335-3600 Technical Inquiries Phone :+86(21) 6335-3030 (Ext.3021) Fax :+86(21) 6335-3600 HONG KONG (Mitsubishi Electric Ryoden Air-Conditioning & Visual Information Systems (HongKong) Ltd.) 7th Floor, Manulife Tower, 169 Electric Road, North Point, Hong Kong Sales Inquiries Phone :+852-2510-1505 Fax :+852-2510-0463 Technical Inquiries Phone :+852-2422-0161 Fax :+852-2487-0181 SINGAPORE (Mitsubishi Electric Asia Pte. Ltd.) http://www.mitsubishielectric.com.sg 307, Alexandra Road, #05-01/02 Mitsubishi Electric Building, Singapore 159943 Sales Inquiries Phone :+65-6473-2308 Fax :+65-6475-9503 E-mail :[email protected] Technical Inquiries Phone :+65-6470-2666 Fax :+65-6475-9503 INDIA (Mitsubishi Electric Asia Pte. Ltd.) 307, Alexandra Road, #05-01/02 Mitsubishi Electric Building, Singapore 159943 Sales Inquiries Phone :+65-6473-2308 Fax :+65-6475-9503 E-mail :[email protected] Technical Inquiries Phone :+65-6470-2666 Fax :+65-6475-9503INDONESIA (Mitsubishi Electric Asia Pte. Ltd.) 307, Alexandra Road, #05-01/02 Mitsubishi Electric Building, Singapore 159943 Sales Inquiries Phone :+65-6473-2308 Fax :+65-6475-9503 E-mail :[email protected] Technical Inquiries Phone :+65-6470-2666 Fax :+65-6475-9503 PHILIPPINES (Mitsubishi Electric Asia Pte. Ltd.) http://www.mitsubishielectric.com.sg 307, Alexandra Road, #05-01/02 Mitsubishi Electric Building, Singapore 159943 Sales Inquiries Phone :+65-6473-2308 Fax :+65-6475-9503 E-mail :[email protected] Technical Inquiries Phone :+65-6470-2666 Fax :+65-6475-9503 VIETNAM (Mitsubishi Electric Asia Pte. Ltd.) 307, Alexandra Road, #05-01/02 Mitsubishi Electric Building, Singapore 159943 Sales Inquiries Phone :+65-6473-2308 Fax :+65-6475-9503 E-mail :[email protected] Technical Inquiries Phone :+65-6470-2666 Fax :+65-6475-9503 STC (Setsuyo Astec Corporation Seoul Branch) 16F KT Bldg., 28-2 Yeouido-dong, Yeoungdeungpo-gu, Seoul 150-931, Korea Sales & Technical Inquiries Phone :+82-1588-5576 Fax :+82-2-704-8666 MALAYSIA (Melco Sales Malaysia Sdn Bhd) Lot 11, Jalan 219, 46100 Petaling Jaya, Selangor Darul Ehsan, Malaysia. Sales & Technical Inquiries Phone : +60-(0)3-79573428 Fax : +60-(0)3-79563950/+60-(0)3-79582576 Technical & Service Inquiries Phone : +60-(0)3-79553997 Fax : +60-(0)3-79584836 ME-TWN (Mitsubishi Electric Taiwan Co., Ltd.) http://www.MitsubishiElectric.com.tw 11TH FL., 90 SEC. 6, CHUNG SHAN N. RD., TAIPEI, 111 R.O.C. Sales & Technical Inquiries Phone :+886-2-2832-8255 Fax :+886-2-2833-9813 MKY (Mitsubishi Electric Kang Yong Watana Co., Ltd. ) http://www.mitsubishi-kyw.co.th/ Road, Huamark Bangkapi, Bangkok 10240, Thailand Sales & Technical Inquiries Phone :+66-2-731-6841 Fax :+66-2-379-4763 Oceania ME-AUST (Mitsubishi Electric Australia) http://www.mitsubishi-electric.com.au/prod.asp?prod=proj 348 Victoria Road, Rydalmere, N.S.W. 2116, Australia Sales & Technical Inquiries Phone :+(612)9684-7777 Fax :+(612)9684-7208 E-mail :[email protected] Technical Inquiries Phone :+(612)9684-7694 Fax :+(612)9684-7684 E-mail :[email protected] BDT (Black Diamond Technologies Ltd.) (Warranty Registration) http://www.bdt.co.nz/projectors/ warranty.asp 1 Parliament St, Lower Hutt, Wellington, New Zealand Sales Inquiries Phone :+64-(0)4-560-9100 Fax :+64-(0)4-560-9133 E-mail :[email protected] Technical Inquiries Phone :+64-(0)4-560-9100 Fax :+64-(0)4-560-9133 E-mail :[email protected] MITSUBISHI ELECTRIC CORPORATION 1 Zusho Baba, Nagaokakyo-City, Kyoto JapanVe r.1