Mitsubishi Ew330u Projector User Manual

EN-21
ENGLISH
Operation
Starting up the projector
1. Plug the power cord into the projector and into a wall socket. Turn on the 
wall socket switch (where fitted). Check that the POWER indicator light 
on the projector lights orange after power has been applied.
• Ask your installation specialist to provide an Earth leakage breaker. When you do 
not use the projector, be sure to shut down the main power by the breaker.
• Please use the original accessories (e.g. power cord) only with the device to 
avoid...

EN-22
Using the menus
The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings.
Below is the overview of the OSD menu.
Below is an example about how to set the OSD language.
1. Press MENU/EXIT on the projector or remote 
control to turn the OSD menu on.3. Press   to highlight Language and press  /  
to select a preferred language.
2. Use  /  to highlight the SYSTEM SETUP: 
Basic menu.4. Press MENU/EXIT twice* on the projector or 
remote control to leave and...

EN-23
ENGLISH
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password 
security. The password can be set through the On-Screen Display (OSD) menu. For details of the OSD menu 
operation, please refer to Using the menus on page 22.
You will be inconvenienced if you activate the power-on lock functionality and subsequently forget the password. Print out this 
manual (if necessary) and write the password you used in...

EN-24
Password: __ __ __ __ __ __
Keep this number in a safe place.
5. Confirm the new password by re-entering the new password.
6. You have successfully assigned a new password to the projector. Remember to enter the new password next time 
the projector is started.
7. To leave the OSD menu, press MENU/EXIT.
Disabling the password function
To disable password protection, go back to the SYSTEM SETUP: Advanced > Security Settings > Power on lock 
menu after opening the OSD menu system. Select Off by...

EN-25
ENGLISH
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These adjusters change the image 
height and projection angle. To adjust the projector:
1. Press the quick-release button and lift the front of the projector. Once the 
image is positioned where you want it, release the quick-release button to 
lock the foot in position.
2. Screw the rear adjuster foot to fine tune the horizontal angle.
To...

EN-26
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs 
when the projector is not perpendicular to the screen. 
To correct this, besides adjusting the height of the projector, you will need to manually correct it following one of 
these steps.
• Using the remote control
Press  /  on the projector or remote control to display the Keystone 
correction page. Press   to correct keystoning at the top of the image. Press...

EN-27
ENGLISH
Selecting the aspect ratio
The aspect ratio is the ratio of the image width to the image height. Most analog TV and computers are in 4:3 ratio, 
and digital TV and DVDs are usually in 16:9 ratio.
With the advent of digital signal processing, digital display devices like this projector can dynamically stretch and 
scale the image output to a different aspect than that of the image input signal.
To change the projected image ratio (no matter what aspect the source is):
1. Press MENU/EXIT and...

EN-28
5.Full: Scales an image to full screen size (16:10). 
The image is projected to fit all over screen. 
(EW330U only)
4:3 picture
16:9 picture
16:10 picture 

EN-29
ENGLISH
Optimizing the image
Selecting a picture mode
The projector is preset with several predefined picture modes so that you can 
choose one to suit your operating environment and input signal picture type.
To select a operation mode that suits your need, you can follow one of the 
following steps.
•Press MODE/ENTER on the remote control or projector repeatedly until 
your desired mode is selected.
• Go to the PICTURE > Setting menu and press  /  to select a desired 
mode.
Picture modes for...

EN-30
Fine-tuning the image quality in user modes
According to the detected signal type, there are some user-definable functions available when User 1 or User 2 mode 
is selected. You can make adjustments to these functions based on your needs.
Adjusting Brightness
Highlight Brightness in the PICTURE menu and adjust the values by pressing  / on the projector or remote 
control.
The higher the value, the brighter the image. And lower the setting, darker 
the image. Adjust this control so the black areas...