Mitsubishi Electronics HOME-CINEMA TELEVISION 738 User Manual

							HOME-CINEMA TELEVISION
MODELS
738 Series
838 Series
BASIC OWNER’S GUIDE
®
This manual provides basic connection, setup, and operating instructions. Please visit our website at 
www.Mitsubishi-tv.com to view or download a detailed owner’s guide that fully describes the features 
of this TV.  Follow the Support link to the Product Documents page.
For questions:•	
Visit our website at www.mitsubishi-tv.com. -
E-mail us at [email protected]. -
Call Consumer Relations at  -800-332-2119 for operational or connection assistance.
For information on •	System Reset, please see the back cover.
To order replacement or additional remote controls, visit our website at www.mitsuparts.com or call •	
800-553-7278.
838 Series.•	  IR emitter cables for NetCommand home-theater control are available for purchase from 
Mitsubishi.  Call 800-553-7278 and request either part number 242D483020 (two-ended cable) or part 
number 299P254020 (four-ended cable). 
						

							For assistance call 1(800) 332-2119
FCC Declaration of Conformity
Product:Projection Television Receiver
Models:WD-60738, WD-65738, WD-73738, 
WD-82738
WD-65838, WD-73838, WD-82838
Responsible 
Party:
Mitsubishi Digital Electronics 
America, Inc.
9351 Jeronimo Road
Irvine, CA 92618-1904
Telephone:(800) 332-2119
This device complies with Part 15 of the FCC Rules.  
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, 
and
(2)  This device must accept any interference 
received, including interference that may cause 
undesired operation.
Note:  This equipment has been tested and found 
to comply with the limits for a Class B digital device, 
pursuant to part 15 of the FCC Rules. These limits 
are designed to provide reasonable protection 
against harmful interference in a residential instal-
lation. This equipment generates, uses and can 
radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may 
cause harmful interference to radio communica-
tions. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this 
equipment does cause harmful interference to radio 
or television reception, which can be determined 
by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one 
or more of the following measures:
Reorient or relocate the receiving antenna. -
Increase the separation between the equip- -
ment and the receiver.
Connect the equipment into an outlet on  -
a circuit different from that to which the 
receiver is connected.
Consult the dealer or an experienced radio/ -
TV technician for help.
Changes or modifications not expressly 
approved by Mitsubishi could cause harmful 
interference and would void the user’s authority 
to operate this equipment.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).   NO USER SERVICEABLE PARTS INSIDE.  REFER 
SERVICING TO QUALIFIED SERVICE PERSONNEL.
TV WEIGHT:  This TV is heavy.  Exercise extreme care 
when lifting or moving it.  Lift or move the TV with a 
minimum of two adults.  To prevent damage to the TV, 
avoid jarring or moving it while it is turned on.  Always 
power off your TV, unplug the power cord, and discon-
nect all cables before moving it.
WARNING:  To reduce the risk of fire or electric shock, 
do not expose this apparatus to rain or moisture.
This apparatus shall not be exposed to dripping or 
splashing and no objects filled with liquids, such as 
vases, shall be placed on the apparatus.
MAINS DISCONNECTION:  The mains plug is used 
as the disconnect device.  The mains plug shall remain 
readily operable.
WARNING:  This product contains chemicals known 
to the State of California to cause cancer and/or birth 
defects or other reproductive harm. 
Note:  Features and specifications described in this 
owner’s guide are subject to change without notice.
Stand Requirement
CAUTION:  Use these Mitsubishi TV models only with 
the Mitsubishi stand models shown here.  Other stands 
can result in instability and possibly cause injury.
TV ModelStand Model
WD-60738, WD-65738
WD-65838MB-S60/65A 
WD-73738
WD-73838MB-S73A 
82-inch TVs.  Mitsubishi does not design, manufac-
ture, or sell matching bases for 82-inch televisions 
(WD-82738, WD-82838).  When selecting a stand, base, 
or other furniture to support the TV, please make sure it 
is designed with the appropriate dimensions for stabil-
ity and to support the TV’s total weight as well as the 
weight of any additional equipment you plan to store.
The lightning flash with arrowhead symbol 
within an equilateral triangle is intended to 
alert the user of the presence of uninsulated 
“dangerous voltage” within the product’s 
enclosure that may be of sufficient magnitude to consti-
tute a risk of electric shock to persons.
The exclamation point within an equilat-
eral triangle is intended to alert the user to 
the presence of important operating and 
maintenance (servicing) instructions in the 
literature accompanying the product. 
						

							For assistance call 1(800) 332-2119
Contents
1  Basic Setup and Operation
Remote Control .........................6
The STATUS Indicator .....................7
Setting Up and Using TV Inputs ..............7
Basic TV Operation.......................9
2   TV Connections
Main Connection Panel ...................10
838 Series Side Inputs  ...................10
Connection Types and Audio/Video Quality  ....10
HDMI Device .............................11
DVI Video Device  .......................11
Y Pb Pr Component Video Device  ...........11
Composite Video Device ..................11
Antenna or Cable TV Service ...............12
VCR or DVD Recorder to an Antenna or  
Wall Outlet Cable  ......................12
A /V Receiver  ..........................13
A /V Receiver with HDMI Output .............13
3   TV Features
FAV (Favorites) .........................14
ChannelView Channel Listings ..............15
Photos and Moving Video as Composite Video ..15
3D Video  .............................16
Sound Projector ........................18
StreamTV™ Internet Media  ................19
Wireless Audio Playback ..................20
4   TV Menus
Picture...............................21
Sound ...............................22
Captions  .............................23
Setup  ...............................24
Inputs ...............................25
Lock ................................26
Appendices
Appendix A:  TV Care
Lamp-Cartridge Replacement and Cleaning .27
Cleaning Recommendations  ............29
Appendix B:  Programming the Remote Control .30
Appendix C:  Troubleshooting ..............31
Mitsubishi TV Software ....................34
Warranty  ..............................38
Network Service Disclaimer ................39
Custom cabinet installation must allow for proper 
air circulation around the television.
NOTE TO CATV SYSTEM INSTALLER:  THIS REMINDER 
IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER’S 
ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PRO-
VIDES GUIDELINES FOR THE PROPER GROUNDING AND, 
IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND 
SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF 
THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY 
AS PRACTICAL.
Internal Fans
Internal cooling fans maintain proper operating tem-
peratures inside the TV.  It is normal to hear the fans 
when you first turn on the TV, during quiet scenes 
while viewing the TV, and for a short time after shutting 
off the TV.  You may notice louder fan noise about 30 
seconds after shutting off the TV and while using the 
Bright Lamp Energy setting.
Lamp Replacement
For lamp-replacement instructions, see Appendix A.
To Order a Replacement Lamp Under Warranty
Call (800) 553-7278.  Please have model number, serial 
number, and TV purchase date available.
Important:  All lamps replaced under warranty 
must be returned to Mitsubishi where they will be 
inspected to verify failure defects.
To Purchase a Replacement Lamp After Warranty
Visit our website at www.mitsuparts.com or call (800) 
553-7278.  Order new lamp part number 915 B 4 410 01.
TV Software
Do not attempt to update the software of this TV with 
software or USB drives not provided by or authorized 
by Mitsubishi Digital Electronics America, Inc.  Non-
authorized software may damage the TV and will not be 
covered by the warranty.
Children and TV Viewing
The American Academy of Pediatrics discourages 
television viewing for children younger than two years of 
age.
For Your Records
Record the model number, serial number, and 
purchase date of your TV.  The model and serial 
numbers are on the back of the TV.  Refer to this 
page when requesting assistance with the TV.
MODEL NUMBER  
SERIAL NUMBER  
PURCHASE DATE  
RETAILER NAME  
LOCATION   
						

							4  
For assistance call 1(800) 332-2119
Important Safety Instructions
Please read the following safeguards for your TV and 
retain for future reference.  Always follow all warnings 
and instructions marked on the television.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4)  Follow all instructions.
5) Do not use this apparatus near water.
6)  Clean only with dry cloth.
7)  Do not block any ventilation openings. Install in 
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as 
radiators, heat registers, stoves, or other apparatus 
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized 
or grounding-type plug. A polarized plug has two 
blades with one wider than the other. A grounding 
type plug has two blades and a third grounding 
prong. The wide blade or the third prong are 
provided for your safety. If the provided plug does 
not fit into your outlet, consult an electrician for 
replacement of the obsolete outlet.
10)  Protect the power cord from being walked on 
or pinched particularly at plugs, convenience 
receptacles, and the point where they exit from the 
apparatus.
11) Only use attachments/accessories specified by the 
manufacturer.
12) Use only with the cart, 
stand, tripod, bracket, 
or table specified 
by the manufacturer, 
or sold with the 
apparatus. When 
a cart is used, use 
caution when moving 
the cart/apparatus 
combination to avoid 
injury from tip-over.
13) Unplug this apparatus 
during lightning storms or when unused for long 
periods of time.
14) Refer all servicing to qualified service personnel. 
Servicing is required when the apparatus has been 
damaged in any way, such as power-supply cord or 
plug is damaged, liquid has been spilled or objects 
have fallen into the apparatus, the apparatus has 
been exposed to rain or moisture, does not operate 
normally, or has been dropped.
AN TE N NA
L E AD  IN  W IR E
A N TE N NA
D IS C HAR G E U NIT
( N EC  A R TIC LE  8 10-2 0)
G RO UNDIN G
C O NDUCTO RS
( N EC  A R TIC LE  8 10-2 1)
G RO UND C LA M PS
P O W ER  S ER VIC E G RO UNDIN G
E LE C TR O DE S YSTE M
( N EC  A R T 2 50, P AR T H )
G
RO UND C LA M P
E LE C TR IC
S ER VIC E
E Q UIP M EN T
N EC  —  NATIO NAL E LE C TR IC AL C O DE
EXAM PLE  O F A N TE N NA G RO UNDIN G
Outdoor Antenna Grounding
If an outside antenna or cable system is connected 
to the TV, be sure the antenna or cable system is 
grounded so as to provide some protection against 
voltage surges and built-up static charges.
Replacement Parts
When replacement parts are required, be sure the 
service technician has used replacement parts speci-
fied by the manufacturer or have the same character-
istics as the original part.  Unauthorized substitutions 
may result in fire, electric shock or other hazards.
The following TV models are 
ENERGY STAR® qualified:
WD-65738, WD-73738, WD-82738
WD-65838, WD-73838, WD-82838
Products that earn the ENERGY 
STAR prevent greenhouse gas 
emissions by meeting strict energy 
efficiency guidelines set by the U.S. 
Environmental Protection Agency 
and the U.S. Department of Energy. 
						

							5
For assistance call 1(800) 332-2119
Basic Setup and Operation
1
Remote Control
Two A A BatteriesAA
A A
Basic Owner’s Guide
HDTV Quick Setup 
Guide
Product Registration 
Card
838 Series.  Calibration 
Microphone
Package Contents
Please take a moment to review the following list of 
items to ensure that you have received everything.
Installing the Remote Control 
Batteries
Remove the remote control’s back cover by 1.  
gently pressing in the tab and lifting off the cover.
Load the batteries, making sure the polarities 2. 
(+) and (-) are correct.  For best results, insert 
the negative (-) end first.
Snap the cover back in place.3. 
2
1The remote 
control requires 
two AA 
batteries.
First-Time Power-On
Press the 1. TV key to 
ensure that the remote 
control is in TV mode.
TV
TV
Aim the emitter (bulb) 2. 
end of the remote control 
at the TV and press the 
POWER key .  Wait for the 
Welcome screen.
If you wish to change the 3. 
menu language to Español, 
press .
Press 4.  to highlight EXIT.  
Press ENTER to clear the 
menu.
Before You Begin
Review the important safety, installation, and oper-1. 
ating information at the beginning of this book.
Choose a location for your TV.2. 
•	 Allow	at	least	four	inches	of	space	on	all	sides	
of the TV to help prevent overheating.  Over-
heating may cause premature failure of the TV 
as well as shortened lamp life.
•	 Avoid	locations	where	light	may	reflect	off	the	
screen.
•	 See	the	stand	requirements	on	page 2.
Install the batteries in the remote control.3. 
Plug the TV into an AC power outlet.4.     
						

							6 1.  Basic Setup and Operation
For assistance call 1(800) 332-2119
Remote Control
Powers TV on or off.
Number/letter keys
Channel tuning, page 8
Pass code entry, page 26
Sleep Timer
Emitter End
TV  CAB/SAT  DVD  AUDIO  VCR
Press the key for the device type to 
control.  Leave in TV mode for normal 
TV viewing.
The TV’s remote control can operate other 
audio/video devices using any of these 
methods:
•	 Program	the	remote	control	for	the	device	(page 
30).
•	 Set	up	HDMI	Control	for	HDMI	devices	compat-
ible with the TV.
•	838 Series.  Perform NetCommand setup for 
device keys.
See the detailed owner’s guide at 
www.mitsubishi-tv.com for information.
GUIDEChannelView listings, page 15.
INFOTV status or TV help.
(PAU S E) Freezes a broadcast TV picture.
Record/Playback controls for external 
devices.  Additional setup is required.
MUTEMutes the TV speakers.
TOOLSDisplays shortcuts for the number keys.  
Press to check if shortcuts are available 
for the current device.
VOLControls volume of TV speakers.
CH 
PAG EChanges channels; moves to another 
page in a menu or list.
Adds a separator in digital channel 
numbers.  Clears some menu entries.    
AUDIOAudio adjustments, page 22
VIDEOVideo adjustments, page 21
MENUDisplays or clears the TV main 
menu (page 21).  Also steps 
back one menu.
EXITClears all menus.
LASTReturns to the previous channel.
838 Series.  Special keys for use 
with NetCommand IR control.  
See the detailed owner’s guide at 
www.mitsubishi-tv.com.
ENTER  Selects a channel number or menu item.
     Navigation and adjustment 
controls
FAVDisplays up to nine favorite 
sources.  See page 14.
F O R M ATChanges picture shape, 
page 14
INTERNETConnects to internet content 
provided by VUDU™.  See 
page 19.
INPUTPress to select a TV input.  
See page 8.
If You Turn Off the TV by Mistake
Press •	POWER again, within about 60 seconds, to 
have the TV come back on immediately.
If the •	S TAT U S indicator is green and blinking rapidly, 
(about 60 seconds after you shut off power), wait a 
few moments for the indicator to stop blinking and 
press POWER to turn the TV on again.                 
						

							 1.  Basic Setup and Operation 7
For assistance call 1(800) 332-2119
The STATUS Indicator
Key   Off   Steady On 
   Slow Blinking   Fast Blinking
LED ColorTV Condition
None TV is powered off.  Normal operation.
Green TV is powered on.  Normal operation.
Green TV powered off, auto-on TV Timer is 
set.
Normal operation.  TV can be turned on 
at any time.
Green TV just powered off and lamp is 
cooling.
Sixty seconds after turning off TV, LED 
will start to blink.  TV can be turned back 
on before blinking starts or after blink-
ing stops, but not while the indicator is 
blinking.  Normal operation.
Yellow TV is too hot.  The TV will display a 
warning message and shut off if it over-
heats.
•	 Ambient	room	temperature	may	be	
too high.  Turn off the TV and let the 
room temperature drop.
•	 Clear	blocked	air	vents.		Ensure	at	
least a four-inch clearance on all 
sides of the TV. 
Yellow Lamp access door is not secure or no 
lamp installed.
TV will not operate until lamp access 
door is secured.  See Appendix A.
Red Lamp failure.  Replace the lamp.  See 
Appendix A.
Red/ 
Yellow 
TV may require service.
Hold power button on front panel for •	
10 seconds to reset TV.
If LED continues to flash red and •	
yellow after reset, turn off the TV and 
unplug it from the AC power source.  
Wait one minute and then plug the 
set back in.
If LED continues to flash red and •	
yellow, go to www.mitsubishi-tv.com 
or call 1-800-332-2119 to receive 
Authorized Service Center informa-
tion.
You may be asked to count how 
many times the LED flashes each 
color to aid in troubleshooting.
Using the ANT (Antenna) Input
If using an antenna or direct cable service (no cable 
box), connect the incoming coaxial cable to the TV’s 
ANT input.  Refer to page 12.
You must perform a channel scan to enable recep-
tion of digital channels.  If you skip this step, the TV 
will receive only analog channels.  The channel scan 
will search for high-definition and standard-definition 
channels available in the local area.
Memorizing Channels with Channel Scan
For the ANT input
To start channel memorization
Power on the TV.1. 
Press 2. MENU and open the Setup > Channel menu.
First press  to navigate to the Setup icon, then 
use  to highlight the Channel icon.
Start channel memorization from the Setup > Channel 
menu.
Press 3.  to enter the menu.
Highlight 4. Ant Air if connected to an 
over-the-air antenna.  Highlight Ant 
Cable for service over direct cable 
(no cable box).  Press ENTER to add a 
check.
For first-time setup, highlight 5. All 
channels.  To scan for channels not 
already in memory, highlight New 
only.  Press ENTER to add a check.
Highlight 6. Scan and press ENTER.  
Channel memorization may take up 
to 15 minutes to complete.
To stop channel memorization before completion, 
press CANCEL.
Setting Up and Using TV Inputs 
						

							8 1.  Basic Setup and Operation
For assistance call 1(800) 332-2119
 Setting Up Other Inputs
Power on the TV.1. 
Power on the devices to ensure detection.2. 
Connect one device to the TV, making note of the 3. 
TV input jack.
The TV will display the New Device Found screen if 
the connection type is detectable.
Highlight the device type in the on-screen list and 4. 
press ENTER.  The name you select here will appear 
in the Input Selection menu.
Sample New Device 
Found screen.
Press 5. EXIT to close the New Device Found screen.
Repeat steps 3 through 5 for each additional device 6. 
you want to add.
About Auto Input Sensing
This TV’s Easy Connect™ Auto Input Sensing 
feature detects most input connections automati-
cally.  Some exceptions are:
A connection on the •	ANT input
TV audio outputs (analog and digital)•	
An HDMI-equipped device that is powered off.  •	
Power on the device first to ensure detection.
Ethernet•	
Auto Input Sensing for Most Devices
When you first connect a device, the TV will:
a.  Detect the connected device and auto-
matically switch to it.
b. Prompt you to identify the device type.
c. Repeat these steps for other newly 
detected devices.
Setting Up and Using TV Inputs, continued
Selecting an Input to Watch
Press 1. INPUT.
Sample Input Selection menu, antenna input selected
Press 2.    to highlight an input icon.
Press 3. ENTER to switch to the input.
Tu ning to Channels on the Antenna Input
Enter the channel number using the number keys •	
on the remote control and press ENTER.
For a two-part digital channel, such as 3-1, press •	3 —
CANCEL.
Press •	CH   /  to change channels one channel at 
a time.
Press and hold •	CH  /  to speed through chan-
nels.
Press •	LAST  to return to the previous channel.
Use the Fav (Favorites) feature to tune to up to nine •	
favorite channels.  See page 14.
Press •	GUIDE to display ChannelView channel listings, 
highlight a channel number, and press ENTER to tune.  
						

							 1.  Basic Setup and Operation 9
For assistance call 1(800) 332-2119
Picture Settings
To get the best picture under different viewing con-1. 
ditions, set the Picture Mode first before changing 
other video settings.  See page 21 for a description 
of the options.
a. Press VIDEO.
b.  Press  until the Picture Mode 
option displays.
c. Press  to make one of these selections:
Name When to Use
Brilliant
Under bright light
GameWith gaming consoles (inputs 
named 
Game or PC only)
Bright For most daytime viewing
Natural For most nighttime viewing
Cinema For recreating theater colors
Press 2.  to display the name of another adjustment.
Press 3.    to make the adjustment.
Wait a few seconds and4.  the display will clear.
Additional picture options are available through the fol-
lowing menus:
MenuPage
Picture > Picture Plus21
Picture > Perfect (838 series)22
Picture > 3D Mode16
Audio Controls
Changing the Audio Output
To switch from the internal TV speakers to an external 
sound system:
Press 1. AUDIO.
Press 2.  to display the 
TV Speakers option.
Press3.      to change.
Basic TV Operation
More TV Features
Features covered in this Basic Owner’s Guide include:
FeaturePage
Parental controls (Lock menu)26
TV Clock.  Set the TV Clock if you plan to use 
the TV Timer (page 24) or ChannelView (page 
15).
24
Favorite sources14
ChannelView and custom channel collections15
Changing the input names that appear in the 
Input Selection menu (Inputs > Name menu)
25
3D Video16
Internet video streaming with VUDU19
Digital camera images as composite video15
838 Series.  Listening to a wireless audio 
device with the TV speakers
20
See the detailed Owner’s Guide at 
www.mitsubishi-tv.com for more on the features 
described here and to learn about other features, 
including:
HDMI control (CEC) of other A /V devices•	
838 Series.•	  NetCommand IR control of other A /V 
devices.  Use of NetCommand requires purchase of 
IR emitter cables available from Mitsubishi.
838 Series.•	  Center and rear channel audio output
838 Series.•	  Using an external subwoofer.
838 Series.•	  Viewing photo files from a USB device.
Changing Audio Settings (TV Speakers Only)
Press 1. AUDIO.
Press 2.   to display the name of the adjustment you 
want.  See page 22 for descriptions.
Press3.    to change.
Controlling Sound Volume
Press •	VOL  /  to adjust the 
sound level of the TV speakers.
See the full owner’s guide at •	
www.mitsubishi-tv.com for 
methods of controlling A /V receiver 
volume. 
						

							10
For assistance call 1(800) 332-2119
2
TV Connections
Auto Input Sensing
The TV’s Auto Input Sensing 
feature automatically recog-
nizes many connections and 
prompts you to identify the 
type of device connected.  
See page 8 for more on Auto 
Input Sensing.
Component
GOOD
BEST GOOD
BEST
VIDEO QUALITY
AUDIO QUALITY
HDMI-to-DVI
HDMI VideoVideo
Composite
L/R Analog
Audio
Audio
Digital
HDMI
Connection Types and Audio/Video Quality 
1 2
3
HDMI
 AUDIO
OUTPUT
P b Pr
INPUT 2
INPUT 1
DIGITAL
AUDIO
OUTPUTDVI/PC
(480i / 480p / 720p / 1080i)
L
R INPUTAUDIO
Y/ VIDE O
Pb PrY/ VIDE O
3D
GLASSES EMITTER
ANT
AUDIOL
R
L
R
 AUDIO/SURROUND
OUTPUTL
R
IR-NetCommand
Output/EXTERNAL
CONTROLLER INPUT CENTER
INPUT
SUB
WOOFER OUTPUT
LAN
++
+
1
2
3
HDMI
 AUDIO
OUTPUT
P b Pr
INPUT 2
INPUT 1
DIGITAL
AUDIO
OUTPUTDVI/PC
(480i / 480p / 720p / 1080i)
L
R INPUTAUDIO
Y/ VIDE O
Pb PrY/ VIDE O
3D
GLASSES EMITTER
ANT
AUDIOL
R
L
R
 AUDIO/SURROUND
OUTPUTL
R
IR-NetCommand
Output/EXTERNAL
CONTROLLER INPUT CENTER
INPUT
SUB
WOOFER OUTPUT
LAN
++
+
838 Series Side Inputs
HDMIpage 11
A
UDIO  
OUTPUT (page 13)
AUDIO /SURROUND 
OUTPUT
(838 series, page 23)DVI/PC AUDIO 
INPUTpage 11
DIGITAL 
A UDIO 
OUTPUT (page 13)
838 Series Jacks.  See 
the full owner’s guide at 
www.mitsubishi-tv.com.
R & L Analog Audio Input
R & L Analog Audio Input
Y Pb Pr (component video)
ANT
page 12
3D GLASSES 
EMITTER
(page 16)
Main Connection Panel
USB(Accessory power on all models;738 Series, wireless adapter, page 19)
HDMIUSB
(page 19)VIDEO  
(composite 
video)
Y Pb Pr  
(component 
video)
USB HDMI 4
INPUT 3
AUDIOLRPbY/ VIDE OPr
SEE DETAIL  B
LAN
(Ethernet, port  
page 19)
VIDEO(composite video)