Mitsubishi Electric Lt 46151 Owners Guide

							 Appendices 81
Reset NameWhen to UseHow to UseResulting Action
FormatWhen	the	picture	
shape	seems	
incorrect,	use	
MORE > 0 (FORMAT)	to	
change	the	shape	of	
the	picture.
Press	the	MORE	key	and	then	repeat-
edly	press	0	(F O R M AT)	to	cycle	
through	the	available	aspect	ratios.
The	last-used	format	for	a	signal	
type	is	memorized	for	each	
input.		The	next	time	the	same	
input	and	the	same	signal	type	is	
viewed,	the	last-used	format	will	
be	recalled.
PerfectColor™ 
Reset
or
PerfectColor™/ 
PerfecTint™ 
Reset (153 and 
249 Series)
(for	the	single	
input	currently	
being	watched)
When	the	color	
intensities	seem	out	
of	balance,	use	the	
PerfectColor/PerfecTint	
reset	to	reset	the	color	
balances	to	the	original	
factory	settings.
Both	PerfectColor	and	
PerfecTint	are	reset	at	
the	same	time.
While	viewing	the	input	to	1. 
be	reset,	press	MENU	and	
go	to	Adjust > Picture+ > 
PerfectColor.
Press	2. ENTER	to	display	the	
PerfectColor	adjustment	screen.
Press	3. CANCEL	to	reset	the	colors.
All	PerfectColor/PerfecTint	
sliders	are	reset	to	the	
original	center	position.		The	
PefectColor/PerfecTint	settings	
for	other	inputs	remain	
unchanged.
A /V Memory 
Reset
(for	the	single	
input	currently	
being	watched)
When	audio	and/
or	video	settings	for	
a	single	input	seem	
incorrect,	use	A /V	
Memory	Reset	to	return	
the	input	to	the	original	
factory	settings.
While	viewing	the	input	to	reset,	1. 
press	MENU	and	go	to	Adjust > 
Reset.
Press	2. ENTER	to	highlight	the	
Reset	icon.
Press	3. ENTER	again	to	reset.
All	Audio	and	Video	settings	
for	the	individual	input	are	
reset	except	for	the	Listen	To,	
Language,	audio	Balance,	
Closed	Caption,	and	Advanced	
Picture	settings.
A /V Reset
(for	all	inputs)
To	reset	audio	and	
video	adjustments	for	
all	inputs	to	the	original	
factory	settings.
While	viewing	the	TV,	press	the	
control-panel	buttons	ACTIVITY	and	
VOLUME DOWN	at	the	same	time	for	at	
least	two	seconds.
All	Audio	and	Video	settings	are	
returned	to	the	original	factory	
settings,	including	Listen	To,	
Language,	audio	Balance,	
Closed	Captions,	and	Format.
TV Reset Comparison Guide
You	can	resolve	 many	common	 TV	problems	 using	the	reset	
functions	described	in	the	following	table.		See	also	the	
troubleshooting	suggestions	later	in	this	appendix.
IMPORTANT
Before you change sound or picture settings: 	If	picture	
or	sound	settings	seem	wrong	for	a	broadcast	channel	
(a	channel	from	the	ANT	input,	a	cable	box,	or	satellite	
receiver),	first	check	other	channels	from	the	same	input	
before	changing	settings.		If	most	other	channels	from	the	
same	input	seem	correct,	there	is	likely	a	problem	with	the	
broadcast	rather	than	with	the	TV.		Use	care	in	this	case,	as	
changes	you	make	to	fix	problems	on	individual	channels	
also	affect	all	other	channels	on	the	same	input.
Appendix E:  Troubleshooting
Service and Customer Support
Service
If	you	are	unable	to	correct	a	problem	with	your	TV,	
consult	your	Mitsubishi	dealer	or	Mitsubishi	Consumer	
Relations	at	(800)	332-2119.
•	 DO	NOT	adjust	any	controls	other	than	those	
described	in	this	Owner’s	Guide.
•	 DO	NOT	remove	the	protective	back	cover	of	your	
T V.
Customer Support
•	 To	order	replacement	or	additional	remote	con-
trols	or	to	purchase	an	IR	emitter	cable,	visit	
our	website	at	www.mitsuparts.com	or	call	
(800)	553-7278.
•	 For	questions:
	 Call	Consumer	Relations	at	800-332-2119.
	 E-mail:		[email protected]
	 Website:		www.mitsubishi-tv.com
249 Series.•			If	you	are	having	difficulty	with	your	
VUDU	account,	contact	VUDU	Customer	Care	at	
www.VUDU.com/support.
 
						

							82 Appendices
Reset NameWhen to UseHow to UseResulting Action
Channel 
Memorization
To	erase	and	
re-memorize	channels	
on	the	ANT input.
While	viewing	the	TV,	press	1. 
MENU	to	display	the	main	menu.
Navigate	to	the	2. Initial> Channel		
menu.
Press	3. ENTER.
Highlight	the	reception	mode,	4. 
e.g.	Ant Air.
Highlight	5. Scan.
Press	6. ENTER	to	start	channel	
memorization.
All	previously	memorized	chan-
nels	for	the	antenna	input	are	
erased	and	a	new	set	of	memo-
rized	channels	is	created.		To	
add	or	delete	individual	chan-
nels,	see	Initial > Channel > 
Edit	menu	instructions	on	page	
48.	
Lock Menu 
Pass Code
To	change	your	Lock	
menu	pass	code
See	the	cutout	page	from	Appendix	D,	
page	79.
Allows	establishment	of	a	new	
code.
Control-Panel 
Lock Release
To	re-enable	the	
control-panel	buttons	
after	activation	of	the	
Control-Panel	Lock
Press	and	hold	the	ACTIVITY	button	
on	the	control	panel	for	ten	seconds.		
If	the	TV	is	powered	off,	you	can	
now	press	the	POWER	button	to	turn	
it	on.
Allows	the	control	panel	to	be	
unlocked	if	the	remote	control	is	
misplaced.
Auto Input 
Sensing for 
HDMI
If	the	New Device 
Found	screen	does	
not	appear	when	you	
connect	an	HDMI	
device.
Disconnect	the	HDMI	device.1. 
Delete	the	HDMI	input	in	the	2. Inputs	
>	Name	menu	(see	page	50).
Power	on	and	connect	the	new	3. 
device.
The	New Device Found	screen	
will	display.
System ResetIf	the	TV	does	not	turn	
on	or	off,	does	not	
respond	to	the	remote	
control	or	control-
panel	buttons,	or	has	
audio	but	no	video.
Press	and	hold	the	POWER	button	on	
the	control	panel	for	ten	seconds.
The	TV	will	turn	off.		Power	on	the	
TV	and	the	green	LED	will	flash	
quickly	for	about	one	minute.		The	
changes	you	made	most	recently,	
before	using	SYSTEM RESET,	may	
be	lost.
TV Reset
I M P O R TA N T:		
Use	this	reset	
only	if	other	
troubleshooting	
has	been	unsuc-
cessful.
To	reset	all	consumer-
accessible	settings	
and	all	memories	to	
the	original	factory	
defaults.
Use	TV	Reset	if	the	TV	
can	respond	to	con-
trols	but	TV	behavior	is	
abnormal.
CAUTION:		All	owner-
performed	setups	and	
adjustments	will	be	
erased. 	
While	viewing	the	TV,	press	1. 
MENU	to	display	the	TV	main	
menu.
With	the	main	menu	displayed,	2. 
press	number	keys	1  2  3	to	
display	the	Reset	menu.
READ THE ON-SCREEN 3. 
WARNING AND INSTRUC-
TIONS.
If	you	do	not	wish	to	use	this	•	
reset,	press	BACK	or	MENU	to	
back	out.
If	you	do	wish	to	use	the	•	
reset,	press	ENTER	to	erase	
all	memories	and	settings.
The	TV	will	start	the	initialization	
process	and	then	turn	off.		
Power	on	the	TV	and	the	front	
green	LED	will	start	flashing.		All	
memory	and	settings	outlined	in	
this	Owner’s	Guide	will	need	to	
be	set	again.
VUDU™Reset VUDU 
Connection
(249 Series)
VUDU	does	not	•	
respond	to	commands.
The	selection	does	not	•	
play	(e.g.,	screen	is	
black	or	the	“Loading”	
messge	is	frozen	on	
screen).
Press	the	MORE	Key.1. 
Press	the	2	key.2. 
The	screen	will	briefly	go	blank	
while	VUDU	initializes.
This	reset	does	not	reset	the	TV	
or	any	TV	settings.
Appendix E:  Troubleshooting, continued
 
						

							 Appendices 83
Appendix E:  Troubleshooting, continued
General TV Operation
SymptomRemarks
	1.The	TV	remote	control	does	not	work.	Check	that	the	batteries	are	fresh	and	installed	correctly.•	
Check	that	the	control	mode	on	the	remote	is	set	to	TV.•	
Be	no	more	than	20	feet	from	the	TV	when	using	the	remote	control.•	
Program	the	remote	control	to	operate	the	TV	or	other	device.•	
Reset	the	remote	control.•	
	2.When	I	try	to	use	the	remote	control,	the	
POWER	key	blinks	five	times.
Replace	the 	batteries.
	3.TV	does	not	respond	to	the	remote	control	or	
to	control-panel	buttons	and	TV	will	not	power	
on	or	off.
Unplug	the	AC	power	cord	for	10	seconds.•	
Press	and	hold	the	POWER	button	on	the	control	panel	to	•	
perform	system	reset.
	4.When	a	device	is	selected	from	the	Activity	
menu,	the	screen	is	blue	or	black	(no	signal	
source).
•	 Make	sure	the	selected	device	is	turned	on.
•	 Begin	play	of	the	device.
	5.You	have	forgotten	your	Lock	menu	pass	code.See	“Bypassing	the	Parental	Lock”,	Appendix	D.
	6.Rating	restrictions	are	not	working.Open	the	Lock	>	Parental	Lock	menu	and:
•	 Verify	that	the	ratings	locks	are	active.
•	 Check	the	Lock	Time/Unlock	Time	to	check	if	rating	restric-
tions	are	disabled.
•	 Rating	restrictions	apply	only	to	content	on	the	ANT	input.
	7.On-screen	displays	appear	each	time	you	
change 	a 	function.
Normal	TV	operation.
	8.
	9.I	have	turned	on	CEC	for	my	HDMI	devices	
but	control	is	erratic	and	I	wish	to	disable	it.
First 	•	turn	off	the	TV’s	HDMI	control	for	the	specific	device.		
Open	the	Inputs	>	HDMI	Control	menu,	select	the	device,	
select	Off.
Disable	CEC	on	the	device	itself.		See	the	device’s	instruc-•	
tions.
If	the	problem	persists,	do	the	following:•	
Disconnect	the	device	from	the	TV.1. 
Open	the	Inputs	>	Name	menu	and	select	Delete	for	the	2. 
device.
Reconnect	the	device	to	the	TV	and	Auto	Input	Sensing	3. 
will	recognize	the	device	with	CEC	disabled.
Reset NameWhen to UseHow to UseResulting Action
VUDU
Reset VUDU 
Account 
Password
(249 Series)
You	have	forgotten	
your	account	pass-
word.
Using	a	computer,	go	to	
www.VUDU.com.
Reset	your	account	password	
from	the	VUDU	website	(requires	
access	to	e-mail).
VUDU
Reset Parental 
Controls 
Passcode
(249 Series)
You	have	forgotten	
your	passcode.
Call	VUDU	Customer	Care	at	
1-888-554-VUDU	(8838).
VUDU	Customer	Care	will	reset	
your	passcode.
 
						

							84 Appendices
Appendix E:  Troubleshooting, continued
TV Power On/Off
SymptomRemarks
	1.TV	takes	an	excessively	long	time	to	power	
on.
When	powered	on,	the	TV	needs	time	to	boot	up,	just	as	•	
does	a	computer.
For	faster	power-up,	change	the	Energy	setting	to	Fast	•	
Power	On	(Initial	>	Energy	menu).		With	this	setting	the	TV’s		
power	usage	when	off	exceeds	ENERGY	STAR®	recom-
mended	levels	for	a	powered-down	device.
	2.You	cannot	program	the	TV	to	turn	on	auto-
matically	(Timer	function)
The	TV	may	be	locked.•	
The	clock	may	not	be	set.•	
	3.TV	turned	itself	off	and	the	light	on	the	front	
panel	started	to	blink.
Momentary	power	fluctuation	caused	the	TV	to	turn	off	to	•	
prevent	damage.		Wait	for	the	green	light	to	stop	flashing	
and	turn	the	TV	on	again.
	If	the	TV	does	not	stay	on,	press	the	POWER	button	on	the	•	
control	panel	for	at	least	eight	seconds	to	perform	System	
Reset.		If	this	happens	frequently,	obtain	an	AC	line	power	
conditioner/surge	protector.
An	unusual	digital	signal	may	have	been	received,	triggering	a	•	
protection	circuit.		Wait	for	the	light	to	stop	flashing	and	turn	TV 	
on.
	4.TV	will	not	power	off.Press	the	POWER	button	on	the	control	panel	for	ten	seconds	
to	perform	System	Reset.
TV Channels
SymptomRemarks
	1.The	TV	takes	several	seconds	to	respond	to	
channel	changes.
It	is	normal	for	digital	channels	to	take	longer	to	tune	in.•	
Press	ENTER	after	entering	a	channel	number	to	avoid	•	
delays.
Use	a	4-digit	number	for	an	over-the-air	digital	channel.•	
Use	a	6-digit	number	for	digital	cable	channels	if	your	cable	•	
service	is	able	to	recognize	6-digit	channel	numbers.
	2.You	cannot	access	a	channel.Use	number	keys	instead	of	CHANNEL	Up/Down.•	
Be	sure	the	channel	you	want	to	view	is	in	memory.•	
Check	that	the	TV	is	switched	to	the	correct	device	or	•	
antenna	for	that	channel	by	pressing	the	ACTIVITY	key.
Make	sure	the	Lock	>	Parent	menu	lock	is	set	to	Off.•	
If	you	cannot	tune	to	a	virtual	digital	channel	even	though	the	•	
TV	has	already	memorized	digital	channels,	tune	to	the	physi-
cal	channel	number	used	by	the	broadcaster.		The	virtual	
channel	will	then	be	automatically	added	to	memory.
You	may	be	trying	to	tune	to	an	analog	channel	that	is	no	•	
longer	broadcasting.
	3.When	ChannelView	list	is	displayed,	informa-
tion	appears	incomplete
Press	INFO	to	update	the	display	for	the	highlighted	channel.•	
Program	information	is	displayed	only	for	the	currently	tuned	•	
channel.
Available	information	is	sent	from	the	broadcaster	or	cable	•	
provider.		No	other	data	is	available.
Make	sure	the	TV	clock	is	set	correctly.•	
 
						

							 Appendices 85
Appendix E:  Troubleshooting, continued
Picture
SymptomRemarks
	1.Picture	does	not	look	like	a	high-definition	
picture.
Not	all	signals	are	high-definition	signals.		To	receive	high-defini-
tion	programming	from	your	cable	or	satellite	provider,	you	must	
subscribe	to	the	provider’s	high-definition	service.			Some	over-
the-air	broadcasts	are	in	high-definition	and	can	be	received	with	
a	high-quality	antenna	suited	to	your	location.
	2.TV	has	sound	but	no	picture.Check	that	all	video	inputs	are	plugged	in	firmly.•	
Press	and	hold	the	POWER	button	on	the	control	panel	for	•	
ten	seconds	to	perform	System	Reset.
	3.Picture	has	become	dimmer.Adjust	picture	brightness	and	contrast	to	maximum	levels.
	4.There	is	a	large	black	or	gray	rectangle	on	
the	screen.
The	TV’s	analog	closed	captioning	has	been	set	to	“text”	mode	
in	the	Captions	menu.		Turn	off	because	there	is	no	text	informa-
tion	being	broadcast.
	5.You	cannot	view	a	picture	when	playing	a	
VHS	tape.
Check	your	VCR’s	owner’s	guide	for	further	troubleshooting.	
	6.VCR	or	DVD	player’s	on-screen	menus	jitter	
up	and	down.
Stop	playback.		Possible	cause:		Many	VCRs	and	DVD	players	
provide	on-screen	menus	at	only	half-resolution	that	may	
appear	to	jitter	up	and	down.
	7.When	viewing	a	stopped	VCR,	white	lines	
are	rolling	on	the	screen.
•	 Turn	off	video	mute	for	the	VCR.
•	 Begin	playing	the	tape.
•	 Change	the	VCR	input	from	Line	1	to	the	VCR	antenna	input.
	8.A	color	program	appears	as	a	black	and	
white	image,	or	the	colors	are	dim,	or	the	
screen	is	black.
The	PerfectColor	color	balance	has	been	incorrectly	set.		Reset	
the	PerfectColor	balance.
	9.Picture	from	an	HDMI	input	is	noisy	(poor	
quality).
Upgrade	a	Category	1	(unmarked)	HDMI	cable	to	a	Category	2	
high-speed	HDMI	cable.
	10.The	image	from	a	computer	appears	dis-
torted	when	viewed	on	the	TV.
Normal	TV	operation.		The	TV	does	not	correct	distortion	in	•	
the	picture	from	a	computer	because	the	correction	process	
may	cut	off	the	edges	of	the	image.
The	aspect	ratio	may	be	wrong	for	the	image.		Press	MORE	•	
and	then	0	(FORMAT)	to	change.
Sound 
SymptomRemarks
	1.There	is	no	sound	even	when	the	
volume	is	turned	up.
•	 Check	if	the	MUTE	key	is	on.
•	 The	TV’s	“Listen	to:”	setting	may	be	set	to	SAP	(analog	program	
from	the	ANT	input)	but	no	SAP	is	being	broadcast.
•	 Check	that	the	Speakers	option	is	set	to	TV	to	hear	sound	from	
the	TV	speakers.		Possibly	sound	is	being	sent	to	one	of	the	audio	
outputs	for	an	A /V	receiver	or	headphones.
•	 If	using	an	A /V	receiver,	check	that	the	Speakers	option	is	set	to	AV	
Receiver	to	hear	sound	from	the	A /V	receiver	speakers.
•	Press	and	hold	the	POWER	button	on	the	control	panel	for	10	
seconds	to	perform	System	Reset.
 
						

							86 Appendices
Appendix E:  Troubleshooting, continued
Sound 
SymptomRemarks
	2.The	sound	does	not	match	the	screen	
picture.
The	TV’s	“Listen	to:”	setting	may	be	set	to	SAP	(analog	program	from	
the	ANT	input).
	3.The	sound	from	my	A /V	receiver	does	
not	match	the	screen	picture	(I	should	
hear	the	correct	audio	from	my	A /V	
receiver).
Check	that	DIGITAL	AUDIO	OUTPUT	and/or	AVR	AUDIO	•	
OUTPUT	on	TV’s	main	panel	is	connected	to	the	A /V	receiver.
Without	this	connection,	devices	connected	only	to	the	TV	(and	
not	the	A /V	receiver)	can	be	heard	only	from	the	TV	speakers.		
Note	that	this	includes	the	ANT	input,	a	device	(such	as	a	
camcorder)	connected	to	the	convenience	panel,	and	any	other	
device	sending	audio	to	the	TV	only.
If	using	a	NetCommand-controlled	A /V	receiver,	NetCommand	•	
may	be	selecting	the	wrong	A /V	receiver	audio	input.		Check	the	
A /V	receiver’s	NetCommand	setup	in	the	Inputs	>	AVR	menu.
	4.Cannot	select	an	audio-only	device;	it	
does	not	appear	in	the	Activity	menu.
Plug	an	unused	video	plug	into	the	Y/ V I D E O	jack	to	activate	Auto	
Input	Sensing	and	make	the	audio	device	selectable	in	the	Activity	
menu.
	5.Sound	is	coming	from	the	TV	speakers	
instead	of	the	A /V	receiver.
Disconnect	headphones.		Connect	the	TV’s	AUDIO	OUT	to	the	A /V	
receiver	and	select	AV	Receiver	from	the	New	Device	Found	screen.
NetCommand IR Control (NetCommand-equipped models only)
SymptomRemarks
	1.Cannot	see	the	menu	from	the	A /V	Receiver.A /V	Receiver	Set	Up	for	Audio-Only	Switching•	
The	A /V	Receiver	is	not	connected	to	any	video	input	of	the	
TV.		To	check	the	A /V	Receiver	menu,	temporarily	plug	into	
an	unused	input	of	the	TV,	such	as	Input	3.		Exit	the	New	
Device	Found	screen	and	select	Input	3	from	the	Activity	
menu.	Press	MENU	on	the	A /V	receiver’s	remote	control.
A /V Receiver Set Up for Audio and Video Switching over •	
HDMI
Use	the	MENU	key	on	the	A /V	receiver’s	remote	control.
A /V Receiver with •	HDMI Control
Switch	the	remote	control	to	AUDIO	mode.		Press	the	
MORE	key	and	then	1	(Menu).
	2.NetCommand	unable	to	learn	specific	device	
keys.
A /V	Device	does	not	use	IR	format	for	remote	control	•	
signal.	ITT	and	RF	formats	cannot	be	learned.
Room	lighting	may	affect	the	signal.		Have	the	remotes	very	•	
close	(6	inches	or	less)	to	the	TV	during	Learning.
If	learning	a	Mitsubishi	remote	control,	make	sure	mode	is	•	
not	set	to	TV.
Some,	but	not	all,	device	key	functions	can	be	learned	by	•	
NetCommand.		For	example,	POWER	and	PLAY	may	be	
learned,	but	other	functions	may	not.
The	signal	from	the	remote	control	may	not	be	strong	•	
enough.		Insert	fresh	batteries	and	try	Learning	again.
 
						

							 Appendices 87
Appendix E:  Troubleshooting, continued
NetCommand IR Control (NetCommand-equipped models only)
SymptomRemarks
	3.The	A /V	receiver	is	the	selected	audio	source	
but	there	is	no	sound.
A /V	Receiver	Set	Up	for	Audio-Only	Switching•	
Check	to	see	if	the	A /V	Receiver	power	is	turned	on.	-
With	A /V	receiver	power	turned	on,	redisplay	the	Activ-	-
ity	menu	and	press	ENTER	to	allow	NetCommand	to	
correctly	select	the	A /V	Receiver	input.
Incorrect	setup	in	the	Inputs	>	AVR	menu.		Check	the		-
device	connection	assigned	in	the	AVR	menu.
A /V	Receiver	Set	Up	for	Audio	and	Video	Switching	over	HDMI•	
Check	to	see	if	the	A /V	Receiver	power	is	turned	on.	-
If	the	device	is	connected	only	to	the	TV	(e.g.,	on	ANT		-
or	a	front	panel	input),	verify	that	the	TV’s	AUDIO	
OUTPUT	is	connected	to	the	A /V	receiver.
The	A /V	receiver	is	not	switching	properly	because		-
you	have	not	learned	the	IR	codes	for	the	A /V	receiver	
inputs	to	which	your	devices	are	connected.
	4.There	is	no	sound	from	the	A /V	receiver	
for	my	DVD	player	or	other	surround	sound	
device	even	though	I	learned	the	IR	code	for	
the	A /V	receiver’s	DVD	input	or	other	input.
(A /V	Receiver	Set	Up	for	Audio-Only	Switch-
ing)
NetCommand	A /V	receiver	setup	for	the	DVD	player	or	digital	
surround	sound	device	or	other	device	is	not	switching	prop-
erly.		See	“Automatic	Switching	(Audio	or	Audio/Video),”	page	
63,	and	perform	A /V	receiver	setup	for	a	digital	surround	sound	
device.
	5.There	is	no	sound	or	picture	from	the	A /V	
receiver	for	my	DVD	player	or	other	device	
connected	to	the	A /V	receiver;	the	A /V	
receiver	should	be	sending	video	to	the	TV	
over	an	HDMI	cable.
(A /V	Receiver	Set	Up	for	Audio	and	Video	
Switching	over	HDMI)
The	NetCommand	A /V	receiver	setup	is	not	switching	audio	
and	video	inputs	properly	because	you	did	not	“learn”	the	A /V	
receiver’s	IR	codes	for	the	device	inputs.		See	“Case	3:		Auto-
matic	Audio	and	Video	Switching	via	HDMI,”	page	65.
	6.I’ve	selected	my	DVD	player	or	other	sur-
round	sound	device	in	combination	with	the	
TV	speakers	but	hear	no	sound	from	the	TV	
speakers.
A /V	Receiver	Set	Up	for	Audio-Only	Switching•	
If	you	have	only	an	audio	connection	from	the	device	to	the	
A /V	receiver,	a	physical	audio	connection	from	the	device	
to	the	TV	is	also	required.
Connect	the	left	and	right	audio	output	from	the	device		-
to	the	appropriate	TV	audio	input.		Now	you	can	hear	
audio	from	the	device	through	either	the	TV	speakers	or	
the	A /V	receiver.
To	switch	audio	sources,	press	MORE	9	(Audio),	press		-
		to	show	the	Speakers	option,	then	press		to	
select	AV	Receiver	or	TV.
A /V	Receiver	Set	Up	for	Audio	and	Video	Switching	over	HDMI•	
With	your	DVD	player	connected	to	the	A /V	receiver,	only	
video	is	passed	from	the	A /V	receiver	to	the	TV	because	of	
copy-protection	restrictions	on	the	HDMI	signal
	7.I	“learned”	the	RECORD	key	for	my	VCR/DVR	
but	when	I	pressed	the	RECORD	key,	the	
VCR/DVR	did	not	record	anything.
Check	that	the	VCR	or	DVR	is	receiving	a	signal	directly	from	
your	cable	box	or	satellite	receiver.
 
						

							88 Trademark and License Information
LICENSOR’S	SUPPLIERS	DO	NOT	MAKE	OR	PASS	ON	TO	END	USER	OR	ANY	OTHER	THIRD	PARTY,	ANY	
EXPRESS,	IMPLIED	OR	STATUTORY	WARRANTY	OR	REPRESENTATION	ON	BEHALF	OF	SUCH	SUPPLIERS,	
INCLUDING,	BUT	NOT	LIMITED	TO	THE	IMPLIED	WARRANTIES	OF	NON-INFRINGEMENT,	TITLE,	MERCHANTABIL-
ITY	OR	FITNESS	FOR	A	PARTICULAR	PURPOSE.
Manufactured	under	license	from	Cambridge	Mechatronics	Ltd.
Rapidfire	and	the	1...	logo	are	trademarks	of	Cambridge	Mechatronics	Ltd
Manufactured	under	license	from	Dolby	Laboratories.		Dolby	is	a	trademark	of	Dolby	Laboratories.
ENERGY	STAR®	and	the	ENERGY	STAR	mark	are	registered	U.S.	marks.		ENERGY	STAR	is	a	registered	mark	owned	
by	the	U.S.	government.
HDMI™	the	HDMI	logo	and	High-Definition	Multimedia	Interface	are	trademarks	or	registered	trademarks	of	HDMI	
Licensing	LLC.
		Imaging	Science	Foundation	Certified	Calibration	Controls
The	software	in	this	TV	is	based	in	part	on	the	work	of	the	Independent	JPEG	Group,	copyright	©	1991-1998,	Thomas	
G.	Lane,	all	rights	reserved.
x.v.Color	and	the	x.v.Color	logo	are	trademarks	of	Sony	Corporation.
VUDU™	is	a	trademark	of	VUDU,	Inc.
ChannelView™,	DeepField™	Imager,	Easy	Connect™,	NetCommand®,	PerfectColor™,	PerfecTint™,	Plush	1080p®	
5G,	SharpEdge™,	Smooth120Hz™	Film	Motion,	Unisen™	are	trademarks	of	Mitsubishi	Digital	Electronics	America,	
Inc.
Trademark and License Information
Network Service Disclaimer
Third	party	content	and	services,	including	without	limitation	home	entertainment	services	by	VUDU,	Inc.,	are	
provided	in	accordance	with	whatever	terms	and	conditions	are	established	by	the	third	party	providers	and	
agreed	to	by	you.	Mitsubishi	Digital	Electronics	America	(“MDEA”)	has	no	control	over	any	such	third	parties	or	
any	agreement	you	reach	with	them.	MDEA	has	no	control	over	the	networks	or	transmission	facilities	by	which	
content	and	services	are	provided	by	third	parties.	Your	connection	to	the	internet	may	vary	in	availability	and	
quality.	Customer	service	questions	are	to	be	directed	to	the	third-party	provider,	not	MDEA.
MDEA	DOES	NOT	WARRANT	CONTENT	OR	SERVICES	PROVIDED	BY	ANY	THIRD	PARTY,	EITHER	
EXPRESSLY	OR	IMPLIEDLY,	FOR	ANY	PURPOSE.	MDEA	DOES	NOT	WARRANT	THAT	ANY	THIRD	PARTY	
SERVICE	WILL	REMAIN	AVAILABLE	FOR	ANY	PERIOD	OF	TIME	OR	THAT	IT	WILL	BE	SATISFACTORY,	UNIN-
TERRUPTED	OR	ERROR	FREE.		MDEA	EXPRESSLY	DISCLAIMS	ANY	IMPLIED	WARRANTIES,	INCLUDING	
BUT	NOT	LIMITED	TO,	WARRANTIES	OF	MERCHANTABILITY	OR	FITNESS	FOR	A	PARTICULAR	PURPOSE	
WITH	RESPECT	TO	ANY	THIRD	PARTY	CONTENT	AND	SERVICES.
MDEA	WILL	NOT,	UNDER	ANY	CIRCUMSTANCES,	BE	LIABLE,	WHETHER	IN	CONTRACT	OR	TORT	OR	
OTHER	LEGAL	THEORY,	FOR	ANY	DIRECT,	INDIRECT,	INCIDENTAL,	SPECIAL	OR	CONSEQUENTIAL	
DAMAGES,	ATTORNEY	FEES,	EXPENSES,	OR	ANY	OTHER	DAMAGES	ARISING	OUT	OF,	OR	IN	CONNEC-
TION	WITH,	YOUR	USE	OF	ANY	CONTENT	OR	SERVICE	THAT	IS	PROVIDED	TO	YOU	BY	ANY	THIRD	PARTY,	
EVEN	IF	ADVISED	OF	THE	POSSIBILITY	OF	SUCH	DAMAGES.
 
						

							 Trademark and License Information 89
Mitsubishi TV Software
END-USER LICENSE AGREEMENT FOR EMBEDDED SOFTWARE
IMPORTANT – READ CAREFULLY:	This	License	Agreement	is	a	legal	agreement	between	you	(either	an	individual	or	an	entity)	and	
Mitsubishi	Digital	Electronics	America,	Inc.	(MDEA)	for	all	software	pre	installed	and/or	provided	along	with	this	television	(“Software”).		By	
utilizing	this	television	and	Software,	you	agree	to	be	bound	by	the	terms	of	this	License	Agreement.
The	Software	is	protected	by	United	States	copyright	laws	and	international	treaty	provisions,	as	well	as	other	intellectual	property	laws	
and	treaties.		The	Software	is	licensed,	not	sold.
1.	LICENSE GRANT. 	MDEA	grants	you	a	non-exclusive,	non-transferable,	limited	right	and	license	to	use	one	copy	of	the	Software	
only	with	the	Mitsubishi	television	model	that	included	this	owner’s	guide	and	owned	by	you.
2.	RIGHTS AND LIMITATIONS.
Software	Not	for	Resale.		You	may	not	resell	or	otherwise	transfer	for	value	the	Software,	except	in	conjunction	with	a	sale	of	the	TV	that	
Software	has	been	pre	installed.
Prohibition	on	Reverse	Engineering,	Decompilation	and	Disassembly.		The	Software	contains	trade	secrets	or	other	proprietary	material	
in	its	human	perceivable	form	and	to	protect	them,	you	may	not	reverse	engineer,	decompile,	or	disassemble,	or	otherwise	reduce	the	
Software	to	any	human	perceivable	form,	except	to	the	extent	that	the	foregoing	restriction	is	expressly	prohibited	by	applicable	law.
Separation	of	Components.		The	Software	is	licensed	as	a	single	product.		Its	component	parts	may	not	be	separated	for	use	on	more	
than	one	TV.
No	Rental.		You	may	not	rent,	lease,	lend,	or	sublicense	the	Software.
Trademarks.		This	License	Agreement	does	not	grant	you	any	rights	to	any	trademarks	of	MDEA.
3.	VIOLATIONS.		You	understand	that	any	use,	copying	or	transfer	of	the	Software,	except	as	permitted	pursuant	to	this	License,	
may	subject	you	to	serious	criminal	and	civil	penalties	including	damages	and	an	award	to	MDEA	of	attorneys’	fees	in	connection	with	any	
violation	of	this	License.		You	further	understand	that	you	may	be	held	legally	responsible	for	any	copyright	infringement	or	other	violation	
of	intellectual	property	rights	that	is	caused,	encouraged,	or	induced	by	your	failure	to	abide	by	the	terms	of	the	License.		This	license	
is	effective	until	terminated,	and	will	terminate	immediately	without	notice	from	MDEA	or	judicial	resolution	if	you	fail	to	comply	with	any	
provision	of	this	License.
4.	COPYRIGHT. 	All	title 	and 	intellectual 	property	rights	in	and 	to	the 	Software 	(including 	but	not	limited 	to	any 	images, 	photographs, 	
animations,	video,	audio,	music,	text,	and	“applets”	incorporated	into	the	Software),	and	any	accompanying	printed	materials	are	owned	
by	or	licensed	to	MDEA.		All	title	and	intellectual	property	rights	in	and	to	the	content	which	may	be	accessed	through	use	of	the	Software	
is	the	property	of	the	respective	content	owner	and	may	be	protected	by	applicable	copyright	or	other	intellectual	property	laws	and	
treaties.		This	License	Agreement	grants	you	no	rights	to	use	such	content,	except	that	you	own	the	media	on	which	the	Software	is	
recorded,	but	MDEA	and	its	licensors	retain	ownership	of	the	Software	itself.		All	rights	not	expressly	granted	are	reserved	by	MDEA.
5.	EXPORT RESTRICTIONS. 	MDEA	is	licensing	the	Software	for	use	within	the	United	States.		You	agree	that	you	will	not	
export	or	re-export	the	Software.		You	specifically	agree	not	to	export	or	re-export	the	Software:	(i)	to	any	country	to	which	the	U.S.	has	
embargoed	or	restricted	the	export	of	goods	or	services,	which	currently	include,	but	are	not	necessarily	limited	to	Cuba,	Iran,	Iraq,	Libya,	
North	Korea,	Sudan,	and	Syria,	or	to	any	national	of	any	such	country,	wherever	located,	who	intends	to	transmit	or	transport	the	Software	
back	to	such	country;	(ii)	to	any	person	or	entity	who	you	know	or	have	reason	to	know	will	utilize	the	Software	in	the	design,	development,	
or	production	of	nuclear,	chemical,	or	biological	weapons;	or	(iii)	to	any	person	or	entity	who	has	been	prohibited	from	participating	in	
U.S.	export	transactions	by	any	federal	agency	of	the	U.S.	government.		You	warrant	and	represent	that	neither	the	BX A	nor	any	other	U.S.	
federal	agency	has	suspended,	revoked,	or	denied	your	export	privileges.
6.	DISCLAIMER OF WARRANTY.  EXCEPT AS OTHERWISE PROVIDED IN THIS LICENSE OR IN THE LIMITED WARRANTY 
APPLICABLE TO THE TV, MDEA MAKES NO OTHER WARRANTIES OF ANY KIND WHATSOEVER REGARDING THE SOFTWARE 
AND HEREBY EXPRESSLY DISCLAIMS ALL WARRANTIES OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, WITH 
RESPECT TO THE SOFTWARE.  ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES 
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY DISCLAIMED BY MDEA.  IN 
NO EVENT SHALL MDEA BE LIABLE TO YOU OR ANY THIRD PARTIES, IN CONTRACT, IN TORT OR OTHERWISE, FOR ANY 
DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE.   BECAUSE SOME 
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES, THE ABOVE LIMITATION MAY 
NOT APPLY TO YOU.
7. 	LIMITATION OF LIABILITY.  MDEA SHALL NOT, UNDER ANY CIRCUMSTANCES BE LIABLE TO YOU OR ANY THIRD 
PARTIES FOR ANY DAMAGES OF ANY NATURE, WHETHER INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR 
OTHERWISE, INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOST PROFITS, LOSS OF GOOD WILL OR EXPENDITURES 
MADE OR COMMITTED FOR IN RELIANCE ON THE CONTINUATION OF THIS LICENSE.  YOU AGREE THAT NEITHER MDEA’S 
BREACH OF THIS LICENSE NOR ITS FAILURE TO REPAIR A DEFECT, ERROR OR BUG SHALL CONSTITUTE A FAILURE OF THE 
ESSENTIAL PURPOSE OF THIS LICENSE.  BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION 
OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.  MDEA’s 
liability to you for direct damages for any cause whatsoever and regardless of the form of the action, will be limited to the money 
paid by you for the TV (based on fair market value of the TV ) that caused the damages.
8.	 GENERAL.		This	License	Agreement	will	be	governed	by	the	laws	of	the	State	of	California.
WARNING:		This	product	contains	chemicals	known	to	the	State	of	California	to	cause	cancer	and/or	birth	defects	
or	other	reproductive	harm.	
 
						

							90 Trademark and License Information
GNU General Public License
Version 2, June 1991
Copyright	(C)	1989,	1991	 Free	Software	Foundation,	Inc.	 	 	 675	Mass	Ave,	Cambridge,	MA	02139,	USAEveryone	is	permitted	to	copy	and	distribute	verbatim	copies	of	this	license	document,	but	changing	it	is	not	allowed.
PreambleThe	licenses	for	most	software	are	designed	to	take	away	your	freedom	to	share	and	change	it.		By	contrast,	the	GNU	General	Public	License	is	intended	to	guarantee	your	freedom	to	share	and	change	free	software--to	make	sure	the	software	is	free	for	all	its	users.		This	General	Public	License	applies	to	most	of	the	Free	Software	Foundation’s	software	and	to	any	other	program	whose	authors	commit	to	using	it.		(Some	other	Free	Software	Foundation	software	is	covered	by	the	GNU	Library	General	Public	License	instead.)		You	can	apply	it	to	your	programs,	too.
When	we	speak	of	free	software,	we	are	referring	to	freedom,	not	price.		Our	General	Public	Licenses	are	designed	to	make	sure	that	you	have	the	freedom	to	dis-tribute	copies	of	free	software	(and	charge	for	this	service	if	you	wish),	that	you	receive	source	code	or	can	get	it	if	you	want	it,	that	you	can	change	the	software	or	use	pieces	of	it	in	new	free	programs;	and	that	you	know	you	can	do	these	things.
To	protect	your	rights,	we	need	to	make	restrictions	that	forbid	anyone	to	deny	you	these	rights	or	to	ask	you	to	surrender	the	rights.		These	restrictions	translate	to	certain	responsibilities	for	you	if	you	distribute	copies	of	the	software,	or	if	you	modify	it.
For	example,	if	you	distribute	copies	of	such	a	program,	whether	gratis	or	for	a	fee,	you	must	give	the	recipients	all	the	rights	that	you	have.		You	must	make	sure	that	they,	too,	receive	or	can	get	the	source	code.		And	you	must	show	them	these	terms	so	they	know	their	rights.
We	protect	your	rights	with	two	steps:		(1)	copyright	the	software,	and	(2)		offer	you	this	license	which	gives	you	legal	permission	to	copy,	distribute	and/or	modify	the	software.
Also,	for	each	author’s	protection	and	ours,	we	want	to	make	certain	that	everyone	understands	that	there	is	no	warranty	for	this	free	software.		If	the	software	is	modified	by	someone	else	and	passed	on,	we	want	its	recipients	to	know	that	what	they	have	is	not	the	original,	so	that	any	problems	introduced	by	others	will	not	reflect	on	the	original	authors’	reputations.
Finally,	any	free	program	is	threatened	constantly	by	software	patents.		We	wish	to	avoid	the	danger	that	redistributors	of	a	free	program	will	individually	obtain	patent	licenses,	in	effect	making	the	program	proprietary.		To	prevent	this,	we	have	made	it	clear	that	any	patent	must	be	licensed	for	everyone’s	free	use	or	not	licensed	at	all.
The	precise	terms	and	conditions	for	copying,	distribution	and	modification	follow.
GNU GENERAL PUBLIC LICENSETERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION0.		This	License	applies	to	any	program	or	other	work	which	contains	a	notice	placed	by	the	copyright	holder	saying	it	may	be	distributed	under	the	terms	of	this	General	Public	License.		The	“Program”,	below,	refers	to	any	such	program	or	work,	and	a	“work	based	on	the	Program”	means	either	the	Program	or	any	deriva-tive	work	under	copyright	law:	that	is	to	say,	a	work	containing	the	Program	or	a	portion	of	it,	either	verbatim	or	with	modifications	and/or	translated	into	another	language.		(Hereinafter,	translation	is	included	without	limitation	in	the	term	“modification”.)		Each	licensee	is	addressed	as	“you”.
Activities	other	than	copying,	distribution	and	modification	are	not	covered	by	this	License;	they	are	outside	its	scope.		The	act	of	running	the	Program	is	not	restricted,	and	the	output	from	the	Program	is	covered	only	if	its	contents	constitute	a	work	based	on	the	Program	(independent	of	having	been	made	by	running	the	Program).		Whether	that	is	true	depends	on	what	the	Program	does.
1.		You	may	copy	and	distribute	verbatim	copies	of	the	Program’s	source	code	as	you	receive	it,	in	any	medium,	provided	that	you	conspicuously	and	appropri-ately	publish	on	each	copy	an	appropriate	copyright	notice	and	disclaimer	of	warranty;	keep	intact	all	the	notices	that	refer	to	this	License	and	to	the	absence	of	any	warranty;	and	give	any	other	recipients	of	the	Program	a	copy	of	this	License	along	with	the	Program.
You	may	charge	a	fee	for	the	physical	act	of	transferring	a	copy,	and	you	may	at	your	option	offer	warranty	protection	in	exchange	for	a	fee.
2.		You	may	modify	your	copy	or	copies	of	the	Program	or	any	portion	of	it,	thus	forming	a	work	based	on	the	Program,	and	copy	and	distribute	such	modifica-tions	or	work	under	the	terms	of	Section	1	above,	provided	that	you	also	meet	all	of	these	conditions:
a)		You	must	cause	the	modified	files	to	carry	prominent	notices	stating	that	you	changed	the	files	and	the	date	of	any	change.
b)		You	must	cause	any	work	that	you	distribute	or	publish,	that	in	whole	or	in	part	contains	or	is	derived	from	the	Program	or	any	part	thereof,	to	be	licensed	as	a	whole	at	no	charge	to	all	third	parties	under	the	terms	of	this	License.
c)		If	the	modified	program	normally	reads	commands	interactively	when	run,	you	must	cause	it,	when	started	running	for	such	interactive	use	in	the	most	ordinary	way,	to	print	or	display	an	announcement	including	an	appropriate	copyright	notice	and	a	notice	that	there	is	no	warranty	(or	else,	saying	that	you	provide	a	warranty)	and	that	users	may	redistribute	the	program	under	these	conditions,	and	telling	the	user	how	to	view	a	copy	of	this	License.		(Exception:		if	the	Program	itself	is	interactive	but	does	not	normally	print	such	an	announcement,	your	work	based	on	the	Program	is	not	required	to	print	an	announcement.)
These	requirements	apply	to	the	modified	work	as	a	whole.		If	identifiable	sections	of	that	work	are	not	derived	from	the	Program,	and	can	be	reasonably	consid-ered	independent	and	separate	works	in	themselves,	then	this	License,	and	its	terms,	do	not	apply	to	those	sections	when	you	distribute	them	as	separate	works.		But	when	you	distribute	the	same	sections	as	part	of	a	whole	which	is	a	work	based	on	the	Program,	the	distribution	of	the	whole	must	be	on	the	terms	of	this	License,	whose	permissions	for	other	licensees	extend	to	the	entire	whole,	and	thus	to	each	and	every	part	regardless	of	who	wrote	it.
Thus,	it	is	not	the	intent	of	this	section	to	claim	rights	or	contest	your	rights	to	work	written	entirely	by	you;	rather,	the	intent	is	to	exercise	the	right	to	control	the	distribution	of	derivative	or	collective	works	based	on	the	Program.
In	addition,	mere	aggregation	of	another	work	not	based	on	the	Program	with	the	Program	(or	with	a	work	based	on	the	Program)	on	a	volume	of	a	storage	or	distribution	medium	does	not	bring	the	other	work	under	the	scope	of	this	License.
3.		You	may	copy	and	distribute	the	Program	(or	a	work	based	on	it,	under	Section	2)	in	object	code	or	executable	form	under	the	terms	of	Sections	1	and	2	above	provided	that	you	also	do	one	of	the	following: