Miele W 4446 Wps Operating Instructions

Rear view
Protruding lid for holding when
moving the machine
Electricity supply cable
Inlet hose with Waterproof system
Drain hoseTransit bar covers
Restraining clip for inlet hose and
drain hose
Restraining clips for transit bars
when removed
Installation and connection
51
 

Installation surface
A concrete floor is the most suitable
installation surface for a washing
machine, being far less prone to
vibration during the spin cycle than
wooden floorboards or a carpeted
surface.
Please note the following points:
The machine must be level and
securely positioned.
To avoid vibrations during spinning,
the machine should not be installed
on soft floor coverings.
If installing on a wooden joist floor:
We recommend a plywood base (at
least 59x52x3 cm). The base should
span...

Using the spanner supplied, turn the
left-hand transit bar 90°, then

withdraw the transit bar.Turn the right-hand transit bar 90°,
then

withdraw the transit bar.
Installation and connection
53
 

To avoid the risk of injury the
holes for the transit bars must be
covered after the transit bars have
been removed.
Fit the covers onto the two holes.
Then plug the holes as shown with
the caps.Secure the transit bars to the back of
the washing machine. Make sure that
holesare fitted over retainers.
The machine must not be moved
without the transit bars in place.
Store them as shown or keep them
in a safe place for future use. They
must be re-fitted if the machine is to
be moved again (e.g. when...

Levelling the machine
The machine must stand perfectly level
on all four feet to ensure safe and
proper operation.
Incorrect installation may increase
electricity and water consumption and
may cause the machine to move about.
Screwing out and adjusting the feet
The four adjustable screw feet are used
to level the machine. All four feet are
screwed in when the machine is
delivered.

Using the spanner supplied, turn
counter nut2in a clockwise
direction. Then turn counter nut2
together with foot1to...

Washer-dryer stack
A T 200, T 4000, T 7000 or T 8000 Miele
tumble dryer can be stacked on this
machine using a WTV stacking kit
which can be purchased from your
Dealer or the Miele Spare Parts
Department.
Washer-dryer stack using a T 7000
series dryer and WTV 417 stacking
kit
aSafety distance to wall:
at least 2 cm
bHeight:
approx. 179 cm
cDepth of the washer-dryer stack:
approx. 67.5 cm
Washer-dryer stack using a T 200,
T 4000 or T 8000 series dryer and
WTV 412 stacking kit
aSafety distance to wall:
at...

The Miele Waterproof system
The Miele Waterproof system protects
the washing machine from water
damage.
The system consists of three main
components:
1) the inlet hose
2) the electronic unit and the washing
machine housing
3) the drain hose
1) Inlet hose
– The inlet hose is fitted with an
additional electrical safety valve
which works like an automatic
stopcock and is housed in the inlet
hose connection box.
– It is pressure tested to between
7,000 and 10,000 kPa.
– The inlet hose has a protective...

Connection to the water supply
The plastic casing of the safety
valve contains electrical
components. The Waterproof system
must only be connected to its own
stopcock. It must not be connected
to mixer taps or similar and must not
be fitted in areas where there is the
risk of water or other liquids
reaching it.
Do not get wet.
The protective sleeve of the hose
must not be damaged or kinked.The machine should be connected to
the mains water supply in accordance
with local and national safety
regulations....

Maintenance and care
If you intend to unscrew the Miele
Waterproof system hose from the
stopcock it is essential to disconnect
the machine from the electricity supply
first.
Only use aMiele Waterproof system
hose should you need a replacement.
In order to protect the water inlet
valve, the dirt filter in the water inlet
valve connection must not be
removed.
Extension hose
A 1.5 metre long (metal) extension hose
is available from your Miele dealer or
the Miele Spare Parts Department as an
optional extra....

Connection to the drainage
system
The machine drains via a drain pump
with a delivery head of 1 metre*. The
drain hose must not be kinked as this
restricts drainage. The swivel elbow at
the end of the hose can be turned in
either direction, or can be detached if
required, with a sharp twist and pull.
If required, the drain hose can be
extended to a length of 5 m. The
necessary parts can purchased from
the Miele Spare Parts Department or
your Miele dealer.
* For a delivery head of more than 1 m
(up to a...