Miele T 7944 C Manual
Have a look at the manual Miele T 7944 C Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 171 Miele manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
External drainage via a sink or gully See Front view illustration. If you want to drain the water off into a sink you will need to secure the hose carefully, e.g. by tying it to a tap to make sure it cannot slip during use. Otherwise there is a risk of overflowing water which could cause damage. Use the bow-shaped guide to prevent the drain hose from becoming kinked. Installation conditions requiring a non-return valve Certain installation conditions require the fitting ofa non-return valve for external water connection(available as an optional accessory). A non-return valve will prevent the risk of back-flow out of the dryer which could cause damage. A non-return valve is required: – If the tumble dryer is connected to a sink drain outlet (see the following section). – If the tumble dryer is connected to a drainage systemalready in useby another appliance, e.g. a dishwasher or washing machine.Example: Connection to a sink drain outlet The drain hose with non-return valve fitted can be connected directly to a suitable sink drain outlet. Remove the following from the back of the dryer at the top: Adapter1and hose clip3behind it. Installation and connection 41
1 Adapter 2 Nut 3 Hose clip 4 End of the hose 5 Non-return valve 6 Tumble dryer drain hoseFit adapter1to the sink drain outlet using nut2. If this nut has a flat disc in it you should take the disc out first. Attach the end of hose4to adapter 1. Use a screwdriver to tighten hose clip3up close to the nut. Non-return valve5has to be fitted with the arrow pointing in the direction of flow (i.e. towards the sink). Otherwise water will not drain out of the appliance. Fit non-return valve5to tumble dryer drain hose6(make sure it is fitted in the correct direction - see arrow on non-return valve). Secure the non-return valve using hose clips. Installation and connection 42
Electrical connection U.K. All electrical work should be carried out by a suitably qualified and competent person, in strict accordance with current national and local safety regulations (BS 7671 in the UK). Ensure power is not supplied to the appliance until after installation work has been carried out. The appliance is supplied with a mains cable with moulded plug ready for connection to a 230-240V mains supply. Please ensure the connection data quoted on the data plate match the household mains supply. Connection should be made via a suitable switched socket which is easily accessible after installation. For extra safety it is advisable to protect the appliance with a suitable residual current device (RCD). Contact a qualified electrician for advice. Do not connect via an extension lead. Extension leads do not guarantee the required safety of the appliance (e.g. danger of overheating).Non-rewireable plugs BS 1363 The fuse cover must be refitted when changing the fuse, and if the fuse cover is lost, the plug must not be used until a suitable replacement is obtained. The colour of the correct replacement cover is that of the coloured insert in the base of the plug, or the colour that is embossed in words on the base of the plug (as applicable to the design of plug fitted). Replacement fuses should be ASTA approved to BS 1362 and have the correct rating. Replacement fuses and fuse covers may be purchased from your local electrical supplier. WARNING: THIS APPLIANCE MUST BE EARTHED Electrical connection 43
Load1Final spin speed in a domestic washing machineResidual moistureEnergy Duration kg rpm % kWh min. Cottons Normal27.0 1000 60 3.90 111 Cottons Normal7.0 7.0 7.0 7.01200 1400 1600 180053 50 48 433.55 3.35 3.25 2.90101 97 93 85 Cottons Normal + Low temperature7.0 1000 60 4.20 175 Cottons Hand iron27.0 1000 60 3.10 89 Cottons Hand iron7.0 7.0 7.0 7.01200 1400 1600 180053 50 48 432.75 2.55 2.45 2.1079 74 71 63 Minimum iron Normal23.5 1200 40 1.40 45 Minimum iron Normal + Low temperature3.5 1200 40 1.50 73 Minimum iron Hand iron3.5 1200 40 1.20 39 Automatic plus Normal5.0 600 50 2.70 114 Delicates Normal2.5 700 50 1.55 116 Denim Normal3.0 900 60 2.40 119 Gentle smoothing1.0 1000 60 0.75 32 Woollens handcare2.0 1000 50 0.15 4 1Weight of dry laundry2EN 61121:2005 test programme All data was calculated using EN 61121:2005 unless otherwise stated. Notes for test institutes: Before testing in accordance with EN 61121, drya3kgload of cotton laundry with 70% residual moisture as per the above standard using the Cottons Normal programme without any extra options. Consumption data can vary from the nominal values given above depending on the size of the load, types of textiles, residual moisture levels after spinning, fluctuations in the electricity supply and any extra options selected. Consumption data 44
Height 850 mm Width 595 mm Depth 634 mm Depth with door open 1074 mm Suitable for pushing under a worktop –Height –WidthYes 850 mm 600 mm Suitable for stacking Yes Weight 52 kg Drum volume 111 l Maximum capacity 7 kg dry weight Capacity of condensed water containerapprox. 4.2 l Drain hose length 1.50 m Maximum delivery head 1.50 m Maximum drain hose length 4.00 m Length of connection cable 2.00 m Voltage Connected load Fuse rating See data plate Lamp wattage Test certificates awarded Energy consumption see Consumption data Technical data 45
Altering the residual moisture level in the Cottons programme The tumble dryer is designed to dry effectively using as little energy as possible. However, if you require the laundry to be drier or damper, you can reduce or increase the default residual moisture in the Cottons programme. Follow the steps ( ,,...) to programme and store in memory. Before you begin, ensure that: – The tumble dryer is switched off. – The door is closed. Press theStart/Stopbutton and keep it pressed in whilst carrying out steps -. Switch the dryer on. Wait until theStart/Stopbutton lights up constantly... . . . and then release theStart/Stop button. – TheLow temperatureindicator light will flash once briefly. Anumberto show which option is selected will appear in the display alternating with the letterP. 0Increased residual moisture. Laundry damper. IStandard residual moisture (factory default setting) (theAutomatic plusindicator light will also flash once). 2Reduced residual moisture. Laundry drier. (theAutomatic plusindicator light will also flash twice). Pressing theStart/Stopbutton switches between the options. Switch the dryer off. The setting you have selected is now stored in memory. You can change it again at any time. To check the setting: Carry out steps to. Switch the dryer off after step. Programmable functions 46
Altering the residual moisture level in the Minimum iron programme The tumble dryer is designed to dry effectively using as little energy as possible. However, if you require the laundry to be drier or damper, you can reduce or increase the default residual moisture in the Minimum iron programme. Follow the steps ( ,,...) to programme and store in memory. Before you begin, ensure that: – The tumble dryer is switched off. – The door is closed. Press theStart/Stopbutton and keep it pressed in whilst carrying out steps -. Switch the dryer on. Wait until theStart/Stopbutton lights up constantly... . . . and then release theStart/Stop button. Press theLow temperaturebutton once. – TheLow temperatureindicator light will flash twice briefly. Anumberto show which option is selected will appear in the display alternating with the letterP. 0Increased residual moisture. Laundry damper. IStandard residual moisture (factory default setting) (theAutomatic plusindicator light will also flash once). 2Reduced residual moisture. Laundry drier. (theAutomatic plusindicator light will also flash twice). Pressing theStart/Stopbutton switches between the options. Switch the dryer off. The setting you have selected is now stored in memory. You can change it again at any time. To check the setting: Carry out steps to. Switch the dryer off after step. Programmable functions 47
Anti-crease Anti-crease helps prevent creasing, if laundry is not normally removed im - mediately after the end of a programme. The anti-crease function –is activated when the tumble dryer is delivered. You can shorten the duration of the anti-crease phase or deactivate it if wished. –is used in all programmes except Woollens handcare. – should be left activated. Follow the steps ( ,,...) to programme and store in memory. Before you begin, ensure that: – The tumble dryer is switched off. – The door is closed. Press theStart/Stopbutton and keep it pressed in whilst carrying out steps -. Switch the dryer on. Wait until theStart/Stopbutton lights up constantly... . . . and then release theStart/Stop button. Press theLow temperaturebutton twice. – TheLow temperatureindicator light will flash 3 times briefly. Anumberto show which option is selected will appear in the display alternating with the letterP. 0Anti-crease off i1 hour anti-crease (theAutomatic plusindicator light will also flash once). 22 hours anti-crease (factory default setting) (theAutomatic plusindicator light will also flash twice). Pressing theStart/Stopbutton switches between the options. Switch the dryer off. The setting you have selected is now stored in memory. You can change it again at any time. To check the setting: Carry out steps to. Switch the dryer off after step. Programmable functions 48
Altering the volume of the buzzer The buzzer has two volumes. Follow the steps ( ,,...) to programme and store in memory. Before you begin, ensure that: –The tumble dryer is switched off. –The door is closed. Press theStart/Stopbutton and keep it pressed in whilst carrying out steps -. Switch the dryer on. Wait until theStart/Stopbutton lights up constantly... . . . and then release theStart/Stop button. Press theLow temperaturebutton three times. – TheLow temperatureindicator light will flash four times briefly. Anumberto show which option is selected will appear in the display alternating with the letterP. 0Normal buzzer (factory default setting) ILoud buzzer (theAutomatic plusindicator light will also flash) Pressing theStart/Stopbutton switches between the options. Switch the dryer off. The setting you have selected is now stored in memory. You can change it again at any time. To check the setting: Carry out steps to. Switch the dryer off after step. Programmable functions 49
Altering the standard drying level in the Automatic plus programme The tumble dryer is designed to dry effectively using as little energy as possible. However, if you require the laundry to be drier or damper, you can reduce or increase the default residual moisture in the Automatic plus programme. Follow the steps ( ,,...) to programme and store in memory. Before you begin, ensure that: – The tumble dryer is switched off. – The door is closed. Press theStart/Stopbutton and keep it pressed in whilst carrying out steps -. Switch the dryer on. Wait until theStart/Stopbutton lights up constantly... . . . and then release theStart/Stop button. Press theLow temperaturebutton four times. – TheLow temperatureindicator light will flash six times briefly. Anumberto show which option is selected will appear in the display alternating with the letterP. 0Increased residual moisture. Laundry damper. IStandard residual moisture (factory default setting) (theAutomatic plusindicator light will also flash once). 2Reduced residual moisture. Laundry drier. (theAutomatic plusindicator light will also flash twice). Pressing theStart/Stopbutton switches between the options. Switch the dryer off. The setting you have selected is now stored in memory. You can change it again at any time. To check the setting: Carry out steps to. Switch the dryer off after step. Programmable functions 50