Miele Pw 6065 Operating Manual

							1. Sort the laundry
^Empty all pockets.
,Foreign objects left in pockets
(e.g. nails, coins, paper clips, etc.)
can cause damage to clothes and
the machine.
^Pre-treat stains.
Tough stains (blood, egg, coffee, tea
etc.) or badly soiled areas (collars and
cuffs) should be penetrated with a stain
remover or a paste made from powder
detergent and warm water. Dab stains
with a damp light colored cloth. Do not
rub!
,Do not use chemical solvents in
the machine.
^
Sort the laundry.General tips
–Dark fabrics often bleed the first few
times they are washed. They should
be washed separately several times
before being included in a mixed
load.
–Remove any lead weights or strips
from curtains before washing.
–Loose underwires should be
removed or sewn in place before
washing.
–Woolens and knitted garments
should be turned inside out.
– Close zippers and hooks and eyes
before washing.
– Comforter covers and pillowcases
should be fastened in order to
prevent small items from rolling
inside of them.
Donotmachine wash items if it is not
recommended on the fabric care label.
Using the washer
11
 
						

							2. Load the washer
^Open the drum door using thea
button.
The drum light lights.
^Load the laundry loosely into the
drum.
For best results, wash mixed loads of
small and large items. This will improve
washing effectiveness and help
distribute the load evenly.
For the lowest energy and water
consumption load the washer to its
max. capacity. See Program guide.
Note: Overloading the washer will affect
wash results and cause wrinkling.
^Close the drum door.
Close the drum door. To prevent
damage to the door seal and
clothing, make sure that there are no
clothes caught between the drum
door and the seal.
3. Select a program
Two program selection possibilities:
–Select a Favorite by pressing the
respective direct select button.
–Select from the Program selection
menu by turning the jog shuttle.
^If desired select Extras and/or a
delay start time with the respective
submenus.
Coin mechanism
If a coin mechanism operates the
machine, please regard the displayed
request to pay.
If the door is opened after a program
has started or if the program is
canceled the credit is lost.
Using the washer
12
 
						

							4. Adding detergent
Use detergent according to the laundry
soiling and water hardness.
Too little detergent may cause:
–ineffective cleaning of laundry;
fabrics may become gray and stiff
over time.
–grease stains on the laundry.
–hard water deposits on the heating
element.
Too much detergent may cause:
– oversudsing with minimal drum
movement; poor wash, rinse and
spin results.
– higher environmental burden.
See Detergent for more information.^Pull out the detergent dispenser
drawer and add detergent.
j= Detergent for the main wash
i= Only add detergent (
1/4of the
total recommended amount of
detergent) to this compartment
for the pre-wash.
§= Fabric softener or liquid starch.
^Close the detergent dispenser
drawer.
Using the washer
13
 
						

							5. Starting a program
Start flashes when a program can be
started.
^Press the Start button.
The Start button lights.
The display shows the approximate
program run time. It will count down in
minutes. The first 10 minutes the
washer calculates the water
absorbency of the laundry. The overall
program time may be shortened or
lengthened.
Additionally the sequence cycle is
displayed. The washer shows the
current program step.
The drum light turns off after the
program starts.
Press one of the following direct select
buttons during the running program:
– ButtonDExtras
the displayed Extras can be selected
or deselected after the program start.
–
ButtonEDelay Start
the time of day and the approximate
program end is displayed.
–
ButtonGCancellation
to cancel the currently running
program. The wash water will be
drained away.
6. At the end of a program
The anti-crease program starts when
the laundry is not immediately removed
from the washer after the program end.
Anti-crease and End will flash
alternately in the display.
^Use theaDoor button to open the
drum door.
^Remove the laundry.
Check the drum for any missed
pieces of laundry. Items
inadvertently left in the washer may
be damaged (e.g. shrink or discolor)
during the next wash cycle.
^
Check the folds of the door seal for
any small articles which may have
been trapped.
^
Close the drum door. Otherwise
foreign objects may find their way
into the drum. These could be
inadvertently washed and cause
damage to laundry.
Using the washer
14
 
						

							The washer has the option to save the most used wash
programs on the direct select buttons. The option Save
must be selected in the Settings - Supervisor level.
Contact Technical Service for access to this level.
Selecting/Changing a Favorite
Main menu
1 Cottons Uni. 60°CProgram selection
2 Minimum iron 40°C SettingsF
3 Delicates 40°C
4 WoollensH30°C12:00
^Press any direct select button, e.g.D.
Basic menu
Cottons Uni.60°C1400 rpm
Duration 0:45 h
Extras
HDelay Start
Y
HSave
HBackA
H
^Turn the jog shuttle to select the component you want to
adjust: program, temperature or spin speed.
^
Press the jog shuttle to confirm the selection.
Depending on the selection the display shows one of the following
submenus.
Important: If no selection is made in the sub-menu, the
display will switch back to the basic menu after 20
seconds.
– Select a program
ProgramBackA
selectionCottons Hygiene
Cottons Uni.
Minimum ironH
^
Select the desired program with the jog shuttle and
confirm. The basic menu shows again.
Favorites
15
 
						

							– Selecting a temperature
Cottons Uni.60°C 1400 rpm
Temperature
cold - 60°Ca
^Select the desired temperature with the jog shuttle and
confirm. The basic menu shows again.
– Selecting the spin speed
Cottons Uni. 60 °C1400rpm
Spin speed
0 - 1400 rpmt
^Select the desired spin speed with the jog shuttle and
confirm. The basic menu shows again.
Selecting Extras
^Press the direct select buttonD. The sub-menu Extras
shows.
Cottons Uni.60°C1400 rpm
OptionsPre-wash
Starch Stop Rinse hold
BackA
^
Select the desired Extras with the jog shuttle and confirm.
The basic menu shows again. Repeat if another Extra is
desired. See Extras for more information.
Favorites
16
 
						

							Saving a Favorite
The basic menu shows all selected components.
Cottons Uni.40°C1400 rpm
Pre-wash
Duration 00:53:00 h
Extras
HDelay StartY
HSave
HBackA
H
^Press the direct select buttonF.
Assigning a direct select button
Cottons Uni.40°C1400 rpm
Pre-wash
until now : Cottons Uni. 60°C1400 rpm
Saving to :1
2 3 4 BackA
^Select the desired number for the favorite with the jog
shuttle and confirm. The favorite is saved with the individual
selections and shows in the main menu.
To assign more favorites, repeat the process with the
remaining direct select buttons.
Favorites
17
 
						

							The basic wash programs can be enhanced with Extras.
Accessing the sub-menu "Extras"
Cottons Uni.60°C1400 rpm
Duration 0:45 h
Extras
HDelay StartY
HBackA
H
^Press the direct select buttonD. The sub-menu Extras
shows.
Selecting Extras
Cottons Uni.60°C1400 rpm
OptionsPre-wash
Starch Stop Rinse hold
BackA
^Select the desired Extras with the jog shuttle and confirm.
– Repeat if another Extra is desired.
– A selected Extra is marked with a tick.
Pre-wash
For laundry with heavy soiling e.g. dust, sand.
Starch Stop
The water is drained away in the last rinse and the program
stops.
Fill the starch directly into the drum and then continue the
program. See Detergent - Separate starch for more
information.
Options
18
 
						

							Rinse Stop
The washer stops after the last rinse, the laundry remains
soaking in water. This will prevent wrinkles if the laundry is not
removed immediately at the end of the wash program.
Intensive*
For laundry with normal to heavy soiling or stains.
The total time for the wash program will be extended.
Water plus*
The washer comes factory set with the Extra selection Water
plus activated. The water level during washing and rinsing is
increased.
Other settings for Water plus can be selected. See Settings
for more information.
* Intensive and Water plus can be added from the Settings
- Supervisor level menu, when the access is activated by
Technical Service.
Extras which can be selected are shown in the sub-menu
Extras. If an Extra is not shown, it is not available for the
selected program.
Options
19
 
						

							The delay start option allows you to select the program end
time. The program start can be delayed between 30 minutes
and 24 hours.
Select the sub-menu Delay Start
Cottons Uni.60°C1400 rpm
Duration 0:45 h
Extras
HDelay StartY
HBackA
H
^Press the direct select buttonE. The Delay Start menu
shows.
Select the Delay Start time
The program end can be selected in 30 minute steps.
Cottons Uni.60°C1400 rpm
12:03Start time:15:45
Finish:16:30
^Select the desired program end time with the jog shuttle
and confirm. The program end time is adjusted to the next
full or half hour. The program start will be delayed
according to the desired program end time.
Starting the Delay Start
^
Press the Start button.
The elapsed delay start time is displayed and will count down
in minutes.
Canceling the Delay Start
^
The Delay Start can be canceled with the direct select
buttonG.
After the program start the actual load size is measured.
This can result in an earlier program end.
Delay Start
20